Search Documents

By Arthur E. Wells

"The present and possible future commercial production of potash from various sources in the United Status is discussed below under the following heads:1. Potash from the saline lakes.(a) Nebraska lakes.(b) California lakes.(c) Other lakes.2. Potash as by-product from the cement kilns.3. Potash as by-product from the iron blast furnace.4. Potash from silicate rocks.(a) Feldspathic material.(b) Leucite rocks of Wyoming..(c) Sericite slates of Georgia.(d) Glauconite (greensand) of New Jersey.5. Potash from Alunite.6. Potash from organic sources other than kelp.7. Potash from kelp.In this discussion very little more than passing reference, if any, will be given to those projects which up to date have been developed only slightly, if at all, beyond the small scale laboratory stage, or for the development of which there appears to be very little financial and technical backing at the present time. Nether or not many of these proposed projects have merit can be determined only by an actual operating demonstration.Generally speaking, the potash industry of the United States has been hardly more than marking time since the armistice. This is, largely due to the fact that the consumers of potash have been expecting that heavy shipments of foreign potash to the United States would be resumed soon at somewhere near the pre-war prices, and they have not seen owing domestic potash at present prices for many months. The result has been that domestic producers have been unable to sell their product at even cost and many producers of potash have been obliged to close down. Thu Nebraska lake plants were closed down in February. The California saline plants were operating at below capacity, and the only large alunite plant is closed down. Even the cement plants have little or no inducements to recover the potash being lost in their waste gases and the production is very small at present.This condition will doubtless continue until a definite policy is decided upon as to the future importation of potash salts from Germany and. France. If unrestricted importation is allowed at prices even 50% greater than in 1913, only a very few, if any, of the domestic projects will be in position to compete with the foreign potash immediately, and the present industry will probably greatly decline with little or no prospect for a future resumption of the industry."

Aug 1, 1919

The Sons of Gwalia Mine in Western Australia is situated about 140 miles north from Kalgoorlie in arid country, where supplies of fresh water are difficult to obtain.Mine salt water is used throughout the treatment plant, whilst fresh water for domestic, boiler, and power purposes is pumped from a number of shallow outlying wells. The waters from all wells are constant in character, although they vary in the quantities of salts contained.An average sample of mixed waters gave the following analysis (Gr. per gal.):Sodium chloride 70.82Magnesium chloride 33.03Calcium chloride 26.98Calcium carbonate .. 11.57Calcium sulphate 22.71Iron oxide and alumina 2.10Silica and insoluble 4.58When this water is used in the boilers in its natural state it is scale-forming and intensely corrosive.

Jan 1, 1927

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By Dezhou Wei, Cong Han, Shuling Gao, Wengang Liu, Yanbai Shen

The recycling schemes of copper mineral to a copper raw ore produced in China is investigated in this paper, of which is aimed at copper concentrate‘s grade is over 26.00% and recovery is over 90.00%. The primary copper mineral the raw ore is chalcopyrite and the main gangue minerals are quartz, orthoclase, albite, clinochlore and phlogopite. There are four useful metal elements contained in the copper raw ore, which are Cu, Pb, Zn, Au and Ag, and the grade of each is 3.75%, 0.01%, 0.11%, 0.31 and 483.5 g/t. Two floating recycling schemes and its corresponding flotation reagent system were determined. The results show that calcium oxide, sodium carbonate and sodium sulphide were used as regulators, sodium n-butylxanthate was used as collector and terpenic oil was used as frother in two floating recycling schemes are effective. The open-circuit test’s results show that the copper mineral contained in raw ore can be effective collected, and both concentrates gotten through two schemes are up to grade.

Jan 1, 2014

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By A. Aitio

Sustainable development is one of the central themes of the work of the World Health Organization; chemical safety is one of its important components. For more than 25 years, WHO has had specialized units for assisting member countries in dealing with their problems in chemical safety. For one of the units involved, International Programme on Chemical Safety, a reorientation is in progress to make best use of existing resources, and to prioritise the work to optimally correspond to the needs of the member countries. The risk assessment work of IPCS, and specifically, the work on chromium and chromium compounds, are discussed.

Jan 1, 2004

By Berk. A. A.

"INTRODUCTION Corrosion of sections of piping used in steam-heating systems is frequently regarded as unavoidable, and periodic replacement is provided. Surfaces exposed to newly condensed steam appear to be especially vulnerable to attack. As an added nuisance, solid products of the corrosion tend to accumulate, plugging return lines.The trouble is ascribed in the main to carbon dioxide and oxygen 3/ 4 / 5/ 6/ dissolved in the condensate. When oxygen is the principal factor, the corrosion usually is characterized by pitting. Carbon dioxide tend3 to cause an acidic condensate which dissolves the metal more uniformly and produces the familiar failure at threaded areas where the piping is relatively thin, and where high stress may tend to acceletate the attack. Carbon dioxide enters the system with the feedwater, generally in a combined form such as carbonates and bicarbonates. Oxygen enters both with the raw feedwater-and as air leaking into lines under partial vacuum. The larger central-heating plants have sought to reduce corrosion by eliminating these gases as much as possible. A smaller plant ordinarily lacks the equipment and technical supervision required for this purpose."

Jun 1, 1944

By Sir Stopford Brunton

Gold was first found in Nova Scotia about 1830-40, but its significance at that time was not appreciated. Probably the first discovery that resulted in any work was made by Lieut. C. !'Estrange, at Mooseland, on the Tangier river, in 1858.1 Since that time gold has been mined with varying success until now, and from 1868 onwards work has never altogether ceased. Gold mining in Nova Scotia is at the moment under a cloud, and the idea generally accepted by most people is that it has failed in the past, and that there is no prospect for it in the future. The actual reasons for the present situation have never been carefully analysed, and it seems a good thing to see what really is the state of the case and whether or not this general idea is worthy of credence. It is the purpose of the present paper to analyse the situation in the light of present knowledge, and to set forth some data which may assist in the future development of the Province.

Jan 1, 1926

By A. P. I. Popoola, T. J. Olaniyi, A. A. Adeleke

"A laboratory froth flotation experiment was conducted on a low-grade carbonatite copper ore sample obtained from Phalaborwa in the Limpopo province of South Africa. The sample was a homogenous hydrocyclone overflow which serves as the feed to the flotation cells at Palabora Mining Company (PMC). The sample has an average copper assay of 0.59% with predominant copper-bearing minerals being chalcopyrite, bornite and cubanite. The carbonatite nature of the ore comes from the high content of calcium (28.85%) and magnesium (6.84%) minerals. Collectors used were sodium diethyl dithiocarbamate and potassium ethyl xanthate alongside Senfroth 38 supplied by Senmin. The results showed that at 200 g/t mixture of collectors (50:50), an optimum grade of 8.03% Cu in the rougher flotation concentrate was achieved at 74% recovery, while during the second flotation, 24.65% Cu was obtained at 74.4% recovery using a Senfroth 38 dosage of 6 L/t with 100 g/t mixed (50:50) collectors. The particle size and pH value of the pulp played a significant role in that the mixed collectors performed efficiently at pH above 8.3 and at room temperature while particle sizes greater than 53 µm were well concentrated when compared with those of less than 53 µm. INTRODUCTION The need for copper ore concentration research is on the rise as a result of the depletion of deposits and the advent of low-grade copper ores. Although most copper ore deposits have other valuable minerals that support their economic extraction, the increase in technological innovations as regards copper usage and applications has increased the demand for copper. Several factors influence concentration results in a froth flotation column, of which the reagent used is most influential."

Jan 1, 2015

By E. K. Kleespies

The Bureau of Mines demonstrated a technique for electrowinning titanium from titanium nitride and titanium dioxide. Titanium-nickel-copper metal solutions containing 26 to 61 weight-percent titanium were prepared by electrolyzing titanium nitride in molten mixtures of potassium fluotitanate) and sodium chloride or barium chloride and depositing titanium on nickel-copper cathodes. A titanium-nickel alloy was prepared by electrolyzing titanium dioxide in an electrolyte of potassium fluotitanate) sodium fluoride) and calcium fluoride and depositing titanium on solid nickel cathodes. This alloy contained 21 weight-percent titanium and had a combined oxygen-carbon content of less than 0.1 weight-percent. A compartmented cell confined the oxide feed near the anode and inhibited oxygen contamination of the metal.

Jan 1, 1966

By Brian Gar Wingfield

Bulk explosive systems have developed from the infancy stages in the early sixties to a sophisticated process of the nineties. With ever changing bulk explosives technology, bulk delivery and loading systems needed to keep pace. Efficiency, as compared with packaged loading, was the keyword allowing faster loading of trucks and shots. Efficiency was also improved by the explosives coupling factor that bulk loading permitted.

Jan 1, 1991

By H. R. Manouchehri

In flotation practices, as particles become finer, such as smaller than 20 μm, process efficiency declines markedly. Selective agglomeration of fine particles is a technique to enhance the recovery of fine valuable minerals in flotation circuits. Different agglomerating methods have been introduced and tested. One method that has recently received much attention is to make use of magnetic force to aggregate fine particles. A selective aggregation of fine paramagnetic particles, such as sulfide minerals, can be achieved in the high-intensity magnetic field prior to or during flotation. The method is simple, selective and effective for fine particles and has low operational cost, though a minimum magnetic susceptibility for fine grains is required to promote the process. In this paper, the implementation of the ProFlote magnetic conditioning device in Boliden’s Garpenberg old concentrator in Sweden, where a complex massive sulfide ore is treated, is presented and discussed based on Boliden’s Garpenberg plant. The results showed an increase in the flotation recovery of fine valuable minerals. Zinc (Zn) production was increased by between 1,100 and 1,500 t/a, while salable yearly silver (Ag) production was increased by 1,500 kg. The copper (Cu) grade in the final concentrate was increased by 1 percent, while reductions in its Zn and lead (Pb) grades were obtained. Moreover, considerable reduction in Zn deportment to the final tail was observed

By B. K. Parekh, Z. Chen

INTRODUCTION The need for cleaning and recovery of fine (minus 28 mesh or 0.5 mm) coal fraction has increased in recent years. This results from realizing a substantial recovery of ultraclean coal from the waste stream improving overall Btu (heat) recovery, providing extra revenue for the coal industry. Also the potential of using the clean coal so obtained for making coal-water mixture which could replace oil. An additional benefit of recovery clean coal from the waste stream is reducing environmental concern of burning uncleaned coal and in waste disposal. Deashing of coal by physical beneficiation processes is limited by the degree to which ash components are liberated from coal. Conventional processes have been inefficient in terms of Btu recovery, for ultrafine coal. Chemical cleaning methods, which involves leaching of ash material from coal, have provided ultraclean coal at high Btu recoveries, are more costly than the physical cleaning methods. An advanced physical separation technique that appears to address the need discussed above is selective flocculation. This technique which has been successfully utilized in iron ore beneficiation offers the potential of processing fine and ultrafine coal to produce a clean fuel. OBJECTIVES The main objective of the present study is to investigate applicability of selective flocculation technique for recovery of clean coal product from the waste coal slurry supplied by the Peabody Coal co., from their three different coal preparation plants. It is also the objective of the program to conduct preliminary economic study of the selective flocculation process.

Jan 1, 2002

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By W. H. Bassett

THE ease and value of the application of spectrum analysis to industrial chemistry appears to be appreciated in few of the large works laboratories of this country. For 8 years, this analysis has been of great value to the authors in both analytical and metallurgical work. To the analyst the complete qualitative analysis of an unknown alloy, revealed by a spectrogram, is a sure basis for the planning of the most direct and rapid method of attack. As the determination of each element proceeds, the purity of precipitates may be checked as often as desired. The spectrograph proves invaluable in the recognition of impurities, the separation of which would entail a lengthy and difficult procedure, or when the weight of an unknown is less than is necessary to complete the desired determinations. A few hundredths of a gram will usually suffice for spectrographic analysis. In the separation of the rarer elements, the spectrograph will show, with precision, the point where each step has been successful. In zinc of certain classes, indium, gallium, and germanium have been isolated in this way; the presence of antimony in lake coppers has been proved; and bismuth has been detected in zinc and in alloys where the presence of a few thousandths of a per cent. would be harmful. An antimony precipitate in a delicate determination may contain a considerable proportion of tin or arsenic, both of which will be revealed. The spectrograph is consequently important to the metallurgist as well as to the analyst.

Jan 2, 1922

By G S. B Karunatillake

Following a pre-feasibility study, Mount Isa Mines commenced a feasibility study on the deposit of the George Fisher Mine in May 1997. Board approval was granted in May 1998 to construct a 2.5 million tonne per annum mine and to upgrade existing concentrator and smelter facilities. The world-class George Fisher zinc-lead-silver deposit is located approximately 22 kilometres north of the city of Mount Isa, in north-west Queensland and is 2.6 kilometres north of the existing Hilton Mine. It will be a large-scale underground mine, sustaining a profitable zinc-lead-silver business in Mount Isa for at least ten years. This paper will outline the details of the mine that was developed during the feasibility and design phase. It will include a description of the mining methods, ventilation, fill, ore handling, services and infrastructure. The utilisation of existing assets and the development of innovative ideas were essential to the successful economic development of the George Fisher Mine.

Jan 1, 2000

Change is inevitable but learning from change is an option. Willingness to learn is one of the first lessons that a leader must learn. Get comfortable and get left behind. I propose to outline the main social changes which are taking place and their impact on the Minerals Industry. Also the changing way we do business and what are the skills needed to manage that change and diversity. How are Associations and Institutes responding to this ever changing environment? More specifically, what is my Vision for the Institute to assist professionals to achieve greater and continuing professional excellence in their chosen professions?

Jan 1, 2000

By Robert M. Matyas, P. E. Sperry, Robert J. Smith, A. A. Mathews

INTRODUCTION The first Dispute Review Board (DRB) was utilized on a tunnel project 20 years ago. Increasingly utilized on a wide range of construction projects, DRB's are becoming the norm on tunnel and underground projects. This paper summarizes the growth in this usage, uses observations and experience to establish that barriers to the utilization of DRB's are more perceived than real and that many arguments against the DRB concept are not valid, and notes some of the salient elements that should be considered in practice to optimize DRB effectiveness. The purpose of the paper is to provide an annotated checklist for current and prospective users. The basic concept, structure, and operation of DRB's are described elsewhere and will not be repeated here (ASCE, 1991). DISPUTE REVIEW BOARD USAGE A compilation of Dispute Review Board usage for tunnel and underground projects to January 1994 indicated use on 63 contracts with a cumulative construction value of $3.8 billion and a total of 60 disputes settled. As of that same date, DRB's were planned for another 63 contracts with an estimated construction value of $4.7 billion. (A listing of these 126 projects is available from the authors.) This success and popularity have spread to other civil projects as well as process and building construction. The increase in DRB usage has been exponential. See Figure 1.

Jan 1, 1995