Search Documents

By T. J. Snell

Bolnore Village in Haywards Heath, Sussex, England, is a large development covering 8 to 10 hectares and expected to provide 1500 homes in five phases to assist in the continuing demand for new homes in the London area. Part of the development required housing on a relatively shallow slope found to have deep seated failure planes which are fairly prevalent in this part of Sussex. Locally the slope angle was around 20 degrees but more typically the gradient was 6 to 7 degrees. There were significant concerns about slope stability and bearing capacity due to pre-existing shear surfaces and the complex geotechnical profile. There was some evidence of instability in the form of residual shear surfaces and tension cracks. The development required terracing the site with retaining structures up to 5 meters in height, formation of access roads and foundations of new houses. The developer Crest Nicholson adopted a collaborative approach with consulting engineers Powell Tolner and specialist geotechnical contractor Keller Ground Engineering. The solution consisted of a novel combination of contiguous bored piling, ground anchors, and both block work and timbacrib retaining walls to ensure the geotechnical issues were adequately addressed within the time and cost constraints set by the team. The paper describes the geotechnics of the problem together with the design, practical implementation, and site progress achieved

Jan 1, 2006

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By J J. Robinson, B N. Noller, D M. Franks, G McIlveen, D R. Mulligan, A T. Soro

Fiji is a developing nation that relies on economic opportunities and recently experienced increased interest in mining and mineral exploration that could potentially benefit the country. In order to understand the lack of, or failure of, past rehabilitation activity, this study applied risk-based approaches to identify the significance of activities or actions applicable to rehabilitation of post-mined land in Fiji. This involved the use of qualitative, semi-quantitative and quantitative risk methodologies, which allow assessment and evaluation of mechanisms of mining administration and practices, as well as rehabilitation methods and approaches that have been applied successfully to post-mined land in other countries with similar environmental and climatic conditions and social and regulatory environments to Fiji. The semi-quantitative risk-based technique followed an earlier approach applied for mine closure by Laurence (2006) and provided a systematic way to assess and evaluate rehabilitation issues that were identified on-site by assessors, who were able to estimate through expert judgement the likelihood and consequences based on conditions, situations observed and circumstances on-site. It demonstrated that experienced professionals could reproducibly score likelihood and consequence of selected items relevant to mine site rehabilitation, despite the wide-ranging issues identified during post mined land rehabilitation. The quantitative risk-based approach was adopted as a method to determine environmental bonds for mining projects using the assessment of consequences and likelihood results from the semi-quantitative approach, then incorporating unit cost of materials or activities for local conditions required to fully rehabilitate each issue at net present value. Application to both an abandoned mine site and a newly opened mine site in Fiji showed that this approach could provide a risk-based estimate for rehabilitation cost and demonstrated potential applicable in the Fijian context.CITATION:Soro, A T, Mulligan, D R, McIlveen, G, Franks, D M, Robinson, J J and Noller, B N, ?2014. Risk-based Rehabilitation Strategies for Post-mined Land in Fiji, in Proceedings Life-of-Mine 2014 , pp 165–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D. Symonds, A. J. Richins, M. G. Nelson

Mining activities at Kennecott and Park City are similar in that both districts began operation in the last half of the 18th century, and both operated on a large scale for many years. However, they are different for two important reasons. First, the mines in the Park City district were always underground. The city of Park City was above many of those mine workings. It remained in place after mining activity stopped, and as the town became an up-scale ski resort, property values increased and the tailings dumps became desirable building sites. In contrast, Kennecott eventually became an open pit mine, and the growing pit effectively consumed many of the small towns that had grown up around the underground workings. Even towns on the periphery of the open pit were razed to allow for the disposal of mine overburden. Second, almost all mining activity stopped in Park City in the early 1970s, just as the first rigorous environmental legislation in the United States was enacted. (The Ontario mine operated sporadically until 1982.) Many mine structures, waste dumps, tailings ponds and piles, and tunnels were simply abandoned as the mining companies ceased business or were bought out. Kennecott, on the other hand, has been in continuous operation for more than 120 years, so a closure plan hasn’t been finalized. Nonetheless, environmental and social problems have arisen, and the company has had to address them.

Mar 2, 2022

By Mark G. Lafontaine

Underground 802.11 wireless communications has become widely adopted for automation and communication purposes but maximizing the wireless signal presents many obstacles given the harsh environment as well as the presence of materials and conditions that can reduce signal propagation. Changes in elevations and curvatures in ramp to drift transitions also affect the wireless signal. Based on the requirements of wireless applications such as voice, data, or location tracking, the wireless site survey is the key tool for measuring and predicting signal strength and signal-to-noise ratio. These readings help determine the maximum distance between access points in order to sustain an overlapping wireless signal where required. This paper describes the methodology and tools used for measuring 802.11 wireless signal strength in an underground mine environment in Northern Ontario. The physical characteristics of the mine and the actual recorded wireless signal data will be presented in order for the audience to gain an understanding of the factors that affect signal throughput. Antenna selection used for the site survey will also be discussed as it played a key role in propagating the wireless signal.

May 1, 2013

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft Sinking operations could be reduced by over 30%, on the average with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

1. BOYD, JAMES. Statement on the Investigation of Natural Resources. Hearings before National Re-sources Economic Subcommittee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 125-131. 2. BUCH, J. W., HENDRICKS, T. A., AND TOENGES, A. L. Statement on the Investigation of Natural Resources. Hearings before National Resources Economic Sub-committee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 231-235. 3. CONGRESS, U.S. An Act to Provide for the Establishment and Operation of a Research Laboratory in the Pennsylvania Anthracite Region for Investigation of the Mining, Preparation, and Utilization of Anthracite, for the Development of New Uses and Markets, for Improvement of Health and Safety in Mining, and for a Comprehensive Study of the Region to Aid in the Solution of Its Economic Problems and to Make Its Natural and Human Resources of Maxi-mum Usefulness in the War Effort. Public, No. 812, 77th Cong., 2d sess. (S-357), ch. 764, approved Dec. IS, 1942, 2 pp.

Jan 1, 1962

The Interior Department's Bureau of Mines is the Federal Government's primary research arm in the mineral and fossil-fuel fields. In accordance with its Organic Act of 1910, the Bureau's responsibilities have been reinforced since the passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966, the Federal Coal Mine Health and Safety Act of 1969, and the Mining and Minerals Policy Act of 1970. The 1966 and 1969 acts deal specifically with the development of safe working conditions and a healthful working environment for those engaged in the mining industry, while the third sets the national policy as follows: " ... to foster and encourage private enterprise in (l) the development of economically sound and stable domestic mining, minerals, metal, and mineral reclamation industries; (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial security, and environmental needs; (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral resources, and (4) the study and development of [ ]

Jan 1, 1972

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

The depletion of good-quality phosphate resources, coupled by a need to supply acceptable products at a rapid rate, while meeting the specifications of fertilizer chemical plants, is of significant concern to the phosphate industry, particularly the production of concentrates with tolerable dolomite content. Tremendous efforts have been made in the past to develop an efficient and economical process that can effectively reject dolomite. However, dolomite removal continues to plague the phosphate industry due to several process-specific challenges being encountered with various beneficiation technologies. In this regard, detailed characterization of phosphate reserves is crucial to understand textural limitations and help design appropriate strategies to achieve quality products. In this paper, the development of procedures to establish dolomite rejection/francolite recovery curves for gravity preconcentration of pebble phosphate from Central Florida is described using high-speed X-ray computed tomography (HSXCT). The developed procedure is illustrated with the analysis of high MgO pebble phosphate samples (10.39 mm × 1 mm) received from South Pasture and Four Corners locations operated by the Mosaic company. The rejection/recovery curves were calculated for each sample for five different particle size classes to observe the trend in rejection/recovery with variation in particle size. In order to evaluate the reliability of the HSXCT data, analysis using the high-resolution X-ray computed tomography (HRXCT) technique was performed on one particular sample (FC-3-1). Finally, to assess the separation efficiency, the HSXCT and HRXCT rejection/recovery curves obtained were compared to experimental gravity preconcentration results reported in the literature. In this way, liberation limitations for gravity preconcentration in the processing of pebble phosphate have been established based on X-ray computed tomography analysis.

By Aimee A. Woolsey

Enterprise Unmanned Traffic Management is a holistic system concept evolving from technological developments in radio frequency where dynamic tracking can be added into current and emerging platforms. This is done through inexpensive RF sensors capable of real-time and cooperative, non-GPS tracking enabling digital visualization of assets, including unmanned aerial systems (UAS). The RF sensors are low size, weight, and power (SWaP), creating efficiencies in energy and material consumption while transmitting positions in real-time and at long ranges. Multiple UAS and other unmanned vehicles can be visualized for risk mitigation in operations,

Oct 17, 2022

By T. J. Ballard

"INTRODUCTION The Buck. Creek corundum area of Clay County, North Carolina, includes one of the largest single masses of peridotite outcrops in the whole Appalachian Range and has been described by Pratt, an early authority on corundum, as offering one of the best potentialities for corundum production in North Carolina.Two principal types of corundum deposits are found at Buck Creek the vein type and the corundum-bearing amphibolite dikes.The vein deposits occur in structural fissures that strike north to northeast in a gangue of feldspar, zoisite, an, chlorite. The corundum is generally coarse-grained and good-quality. The corundum content varies from several percent to 50 percent.The corundum in the amphibolites is more or less disseminated through the dike, is generally lower-grade, and is less in quantity, than the vein corundum. About 50 percent of the amphibolite corundum is coarse enough for snagging-wheel grade but is difficult to separate from the amphibolite.Production from the Buck Creek area has been small and came mainly from high-grade pocket in the vein deposits. Pratt 3/ reports 300 tons of corundum ore was produced to about 1896. No record of subsequent production is available.The critical shortage of corundum during the war, due to transportation difficulties and the depletion of deposits abroad, prompted the Bureau of Mines to investigate domestic reserves.After a favorable report was obtained on the Buck Creek area, the Bureau began exploration of the deposit in September 1943 and continued until February 1945."

Apr 1, 1947

These proceedings consist of papers presented at three Bureau of Mines Technology Transfer Seminars on ergonomics in the mining industry. These seminars were held in December 1981, and covered topics relating to ergonomics and mining in the areas of the man-machine interface, and design of the work environment. This area of research is directed toward reducing accidents traditionally associated with human error.

Jan 1, 1981

By J. Restrepo, N. Ripepi

"The International Organization of Standards defines risk as “the effect of uncertainties on achieving objectives (15).” In mining, many uncertainties can influence the outcome of personal or professional objectives and are often difficult to predict. Risk management, the minimization and control of adverse effects from exposure to identified risks, is a well-established concept that can summarized as “being smart about taking chances” (12). Risk management now consists of management processes unique to numerous organizations across many industries, as varying sectors encounter a variety of needs, including the analysis and mitigation of risks related to physical security, product liability, information security, various forms of insurance, regulatory compliance, and workplace safety (12). The reoccurrence of multiple fatality events in the US mining industry, especially the underground coal sector, suggests an opportunity for improved methods of major safety hazard identification, assessment, and mitigation. A risk management approach would include ready identification and mitigation of these risks, inclusive stakeholder engagement, and rapid integration. While many solutions to reducing the risk of mine disasters have been proposed including stricter regulation and improved technology, a comprehensive risk management approach has yet to be fully integrated in the US mining industry. In December of 2006, R. Larry Grayson of the National Mining Association’s Mine Safety Technology and Training Commission called for “a new paradigm for ensuring safety in underground coal mines, one that focuses on systematic and comprehensive risk management as the foundation from which all life-safety efforts emanate (7).” A risk management approach has already been implemented with success in Australia’s minerals industry as part of a transition during the mid-1990s from a prescriptive based health and safety attitude to a more proactive, duty-of care [risk-based] philosophy (13, 16, 17).FUNDAMENTAL ELEMENTS OF RISK MANAGEMENT TECHNIQUES The fundamental components of a comprehensive risk assessment/management program are well-established within the realm of mining health and safety. Figure 1 depicts the elements of a typical mining hazard management framework. The first step in any safety-based risk management system is to identify and assess hazards by their location, nature, and magnitude within a mine. Next, a decision is made about choosing to eliminate, mitigate, or tolerate each hazard. Ideally, a hazard will be eliminated during the design stages of mining, though dynamic mining conditions often require continuous improvement and reevaluation of existing hazard controls. If elimination is not possible, hazard mitigation actions can consist of methods, rules, equipment, competencies, or other mechanisms. If a hazard is simply tolerated, as many inherent mining hazards must be, then specialized administrative controls must be utilized to minimize losses. During this process, the performance of each action is monitored and modified as needed (13)."

Jan 1, 2015

By G. Graves, J. A. Walker

"Abstract - The Mount Fronsac North volcanogenic massive sulfide deposit is the most recently discovered massive sulfide body in the Bathurst Mining Camp. The deposit occurs within a sequence of intercalated fine-grained felsic tuff and sedimentary rocks (Little Falls member), at the top of the Nepisiguit Falls Formation. Aphyric to sparsely feldspar-phyric rhyolite and related volcanic rocks of the Flat Landing Brook Formation overlie the host sequence. The massive and semimassive parts of the deposit have a north-south strike length of 525 m and a dip of ~45°E; the deposit is continuous downdip for 600 m, and thickness varies from 2 to 20 m. The deposit contains an estimated geologic resource of 14 Mt of low-grade, semimassive (>60%) to locally massive sulfides, and includes a high-grade zone of 1.26 Mt grading 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, and 0.40 g/t Au. The semimassive to massive sulfide intersections occur in an envelope of quartz-sericite±chlorite schist, which is interpreted to be intensely deformed felsic tuff. This sequence has a maximum thickness of 140 m and contains significant (up to 50%) fine- to coarse-grained disseminated pyrite. The pyritic envelope has a strike length of 900 m and extends over 1000 m downdip. Massive sulfides are found throughout this alteration envelope, but more commonly occur at or near the upper contact. The significance of the discovery of this deposit is that it represents a near surface discovery of a large tonnage sulfide body in a mature mining camp, one in which the possibility of discovery of a new shallow deposit had been all but discounted. This opens the possibility for future discoveries in this part of the Bathurst Mining Camp. Sommaire - Le gîte de sulfures massifs volcanogènes du Mont Fronsac Nord est la découverte de sulfures massifs la plus récente dans le Camp Minier de Bathurst. Le gisement est situé dans une séquence de tufs felsiques à grains fins interlités de roches sédimentaires (membre de Little Falls, au sommet de la Formation de Nepisiguit Falls. La partie massive et la semimassive s’étendent du nord au sud sur 525 m et ont un pendage de ~45°E; le gisement est continu sur 600 m en angle de chute et son épaisseur varie de 2 à 20 m. Le gisement contient une ressource géologique évaluée à 14 Mt de sulfures semimassifs (>60%) localement massifs à basse teneur, incluant une zone à haute teneur de 1.26 Mt titrant 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, et 0.40 g/t Au. Les intersections de sulfures semimassifs à massifs se situent dans une enveloppe de schiste à quartz-sericite ± chlorite interprétée comme un tuf felsique intensément déformé. Cette séquence contient une quantité importante (jusqu’à 50%) de pyrite disséminée dont le grain varie de fin à grossier et son épaisseur maximale est de 140 m. L’enveloppe pyriteuse s’étend latéralement sur 900 m et a été tracée jusqu’à 1000 m en angle de chute. Des sulfures massifs sont trouvés partout à l’intérieur de cette enveloppe d’altération, mais ils sont plus fréquents près du contact supérieur. L’importance de cette découverte tient à ce qu’elle est un exemple d’un gisement à fort tonnage nouvellement découvert à une faible profondeur dans un camp minier mature, i.e., un camp ou l’on ne croyait plus qu’il était possible de trouver un gisement près de la surface. Ceci ouvre la porte à la possibilité d’autres découvertes dans cette partie du Camp Minier de Bathurst."

Jan 1, 2006

Jan 1, 1988

By Fernando O. Boechat

Com a redução da oferta de minério granulado de boa qualidade no mercado mundial e as restrições ambientais à sinterização, as pelotas de minério de ferro passaram a ocupar um papel importante como matéria prima para produção de ferro primário. Entretanto, embora apresentem maior resistência à degradação, as pelotas ainda sofrem com este problema, embora em menor magnitude, quando comparadas com granulados. Pode-se identificar a degradação das pelotas de minério de ferro em duas etapas, durante o manuseio e sob redução. Uma vez que vários estudos já analisaram a degradação durante o manuseio, a degradação durante a redução torna-se um assunto relevante e pouco explorado. Assim, o presente trabalho avaliou as energias envolvidas no movimento da carga ao longo de um forno de redução direta do tipo Midrex, usando o método dos elementos discretos. Para isso, foi utilizado o software EDEM® para obtenção das energias dissipadas durante as colisões das partículas. Aplicando estas energias ao modelo mecanicista proposto por Tavares e Carvalho [4] para fragmentação das partículas foi possível estimar a taxa de geração de finos no interior do forno. Estes resultados foram utilizados na previsão da degradação mecânica de pelotas no interior do forno, que previu a geração de 1,2 a 2,6% de finos gerados em um forno Minimod®, dependendo das premissas usadas.

Aug 1, 2018

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977

By Xiang-dong XING, Zhen-yang wang, Xing-le LIU, Jian-Liang Zhang

Experiments were carried out by adding CaF2 as catalyst in a Ar atmosphere to study the isothermal reduction kinetics of vanadium titano-magnetite carbon composite pellets under high temperature in the range from1473 to 1673K. By analyzing reduction mechanism, it was found that the rate controlling step was gas diffusion, and the activation energy was 178.39kJ•mol-1 without adding any catalysts. Adding CaF2 of 3% to vanadium titano-magnetite carbon composite pellets can decrease the apparent activation energy of reduction, and the decrease extent was 14.95kJ•mol-1. In addition, temperature is an important factor influencing on reaction rate.

Jan 1, 2015

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By Robert S. Sanford, Harold C. Pierce

"At one time the Alaskan Eskimo lived in many small settlements scattered along the Arctic coast. These settlements extended as far south as Bristol Bay and several miles inland on the large rivers. When the white man established trading posts, schools, hospitals, and missions, these people gradually congregated around them in a few large villages. The natural fuel supply near many of the large villages along the Arctic coast became exhausted as a result of the abnormally large influx of people from small outlying settlements.The population of Barrow, Alaska, according to the 1940 census, is 363 persons, but since that time it has increased considerably, and later estimates place the present population between 400 and 500 persons. With the exception of 25 white persons, the entire population is comprised of Eskimos.The government maintains a school, hospital, radio station, and weather station at Barrow. In addition to the government, installations, there is a church, a privately owned trading post, and cooperative store owned by the Eskimos.For many years the Barrow Eskimos depended on driftwood and petroleum residue from Cape Simpson for their fuel supply. This fuel provided not only warmth for the Eskimo during the long cold winters but also heat for melting ice, the only source of 'water during .the winter. In recent years the sources of petroleum residue and driftwood have not been adequate to meet the demands for fuel During the winter of 1942-43 and again in 1943-44, Barrow experienced an acute shortage of fuel.The fuel problem at Barrow was brought to the attention of Governor Ernest E. Gruening, who was instrumental in getting a Bureau of Mines engineer4/ to investigate reported coal occurrences in the vicinity. Coal deposits along the Meade River and at Peard Bay were examined during the spring and fall of 1943. The Alaska Native Service shipped in mining equipment in September 1943 and commenced stripping an open-pit mine on the Meade River in June 1944. In conjunction with this work, an engineer5/ of the Bureau explored by churn drilling to determine the tonnage of- coal in the vicinity of the mine. In addition to this work, the Bureau of mines examined coal deposits in Peard Bay area and along the Kuk River south of Wainwright."

Nov 1, 1924