Search Documents

By Ivan F. Avery

DOMESTIC production of carbon black increased 4 percent in 1962 to 2,056 million pounds. Furnace black output was 8 percent, or 132 million pounds, above that in 1961 and accounted for 90 percent of total carbon black production. Channel black output continued to decline and was 55 million pounds less than in 1961. Carbon black shipments during the year totaled 2,082 million pounds and were 5 percent above those of 1961. About one-fifth of these shipments were exported; the balance were sold domestically. An increase of 180 million pounds in domestic sales was partially offset by a decline of 80 million pounds in exports. Total value of carbon black production in 1962 was $145 million. The average value per pound of 7.06 cents was 0.24 cent per pound less than in 1961. Producers' stocks declined 26 million pounds during the year.

Jan 1, 1963

By L. Rodd, C. Walker, T. Koehler

"The energy content of slag represents approximately 80% of the total energy inputs to a laterite nickel electric smelting furnace. Conventional slag handling methods produce only low grade heat and the entire thermal content of the slag is wasted. A heat recovery system proven on BOF slag in the mid 1980's can be adapted to a laterite nickel rotary kiln electric furnace (RKEF) plant. Slag is granulated using a high velocity air jet inside a waste heat boiler to produce slag granules. Granules are cooled during flight via radiation to water-cooled boiler walls and by convection to the granulation air. This system has the potential to recover 80% of the total slag energy in the form of hot air and steam.Integration of the recovered slag energy into the RKEF smelter can be achieved by a number of methods, including the use of preheated air at the ore dryers, kiln or existing power plant. Energy from the slag boiler may be used to reheat boiler feed water from the power plant or to produce superheated steam and generate electricity. The heat recovery system can provide up to 25 - 30% of the total electrical requirement of each RKEF line and a reduction in CO2 emissions of 234,000 tonnes per year.The total cost of slag heat recovery, including CAPEX and OPEX, is $2.5/GJ, which is competitive with using coal when CO2 credits are $18 per tonne. With Clean Development Mechanism (CDM) carbon credits currently selling at €13 ($20 USD) per tonne CO2, there is considerable opportunity for slag producers in regions including South America, Korea, Indonesia and Africa. Increasing fuel costs and more wide-spread legislation for GHG emissions will likely create conditions in which slag heat recovery could generate a favourable return on investment."

Jan 1, 2010

By B. J. CROSS., Henry Kreisinger, John Blizard, C. E. Augustine

This bulletin presents the results of 36 tests made on a 468-horsepower Edge Moor boiler fired with pulverized coal at the Oneida Street Station of the Milwaukee Electric Railway & Light Co., Milwaukee, Wis. The tests were made by the fuel section of the United States Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation. Illinois coal was used as fuel; the furnace, burners, and feeders were designed by the Locomotive Pulverized Fuel Co. The object of the tests was to determine what over-all boiler efficiency could he obtained with pulverized coal under various conditions of furnace operation and with coal of different fineness and moisture content. The investigation was thorough. The pulverized coal, as it was supplied to the furnace, was weighed in specially designed tanks placed on platform scales. Twenty-nine of the tests were of 24 hours duration, three of 16 to 18 hours, and four of 12 hours. All tests are reported excepting two-8 and 20-which had to be stopped abruptly, No.8 because a motor actuating the coal-feed screw burned out and No. 20 because of trouble with the feed pump. Tests 1 to 27, inclusive, were made with round burners and tests 28 to 3Rwith spreading burners. In the first nine tests a large excess of air was supplied in an effort to prevent the ash fusing at the bottom of the furnace. In tests 10 to 16 the supply of excess air was reduced in order to get a high efficiency, regardless of the slagging of ash at the furnace bottom. Tests 17 to 27 were made with a water screen about 10 inches above the bottom of the furnace, to make possible the burning of coal with a small supply of excess air without the ash fusing at the bottom of the furnace. Tests 28,29, and 30 were made without the water screen and with a small supply of excess air, and tests 31 to 38 with a water screen around the walls near the bottom of the furnace. Tests 32, 33, 34, and 35 were run with coarser coal than that used ordinarily at the plant. Tests 36,37, and 38 were made with undried coal.

Jan 1, 1923

By H. O. Hofman

Jan 1, 1896

By I. AITKENS

Turquoise is prized solely for its attractive color ; it is dull and opaque , wholly lacking the brilliant luster that is the chief attraction of transparent gems . The best quality of turquoise is blue , of a soft and pleasing tone , like the color of clear sky but distinctive , as indicated by use of the term " turquoise blue . " Often its value is lessened by a greenish cast ; in many stones the green predominates . A large proportion of the turquoise that is mined is utterly worthless , so inferior and unattractive is its color . The finest grade of turquoise comes from Persia , notable from Nishapur . Large quantities have been mined in the Southwestern States of the United States , and less important deposits have been found in a number of the other States .

Sep 1, 1931

By R. Romano, E. Montalar, J. B. Serón

The SMR geomechanics classification system (adaptation of RMR for slopes) is reviewed with data from 87 actual slopes in Valencia. In a research project, SMR has been applied by a GIS system, as a method to forecast stability problems in future road construction. As a result of this work a methodology for GIS application has been developed. On revient sur la classification geomechanique SMR ( une adaptation du RMR pour talus et pentes) avec les dates de 87 talus existant autour de Valencia. Dans le cadre d’un projet de recherche SMR a été appliquée, avec un système GIS, comme méthode de prévision de stabilité problèmes dans la construction de futures routes. Une méthodologie pour l’application du GIS a été développe. Das Geomechanische Einteilungssystem SMR (eine Anpassung des RMR an Böschungen) wird an Hand der Daten von 87 Böschungen im Gebiet von Valencia überdacht. In einem Forschungsprojekt wurde das SMR in einem Geographischen Informationssystem (GIS) als Methode zur Vorhersage von Stabilitätsproblemen bei zukünftigen Straßenbauprojekten eingesetzt. Das Ergebnis dieser Arbeit ist die Entwicklung einer Methodologie für die GIS-Anwendung

Jan 1, 2003

By Mary S. Esfandiary

U.S. scientists attempting to maintain continuous surveillance of scientific information are confronted with two acute problems: The steady, even spectacular; increase in the volume of such information and the fact that much of it is published in unfamiliar foreign languages, According to the National Science Foundation, almost one-third of the world's scientific literature is published in languages that are read by less than 5 percent of U.S. scientists. Most scientists in the United States must rely on abstract journals and translations to obtain information on developments in research and investigations conducted in the non-English-speaking countries. However, there are problems involved in procuring suitable abstracts and translations and in obtaining such information as cheaply and rapidly as possible.

Jan 1, 1961

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By Sabri Ergun

NEW theoretical data are presented for the intensity of X-rays diffracted from randomly oriented aromatic and alicyclic molecules and diamondlike structures such as are found in coals, cokes, and carbonaceous materials. Data have been computed using the Debye interference function. Computations for the smaller molecules have been made with the Univac 1204 computer: those for large structures, with either the IBM 704 or Bendix G-20 computer. A brief theoretical introduction of the Dobye interference function is given, and an outline is made of the treatment of experimental data so that the experimental interference function can be obtained.

Jan 1, 1965

Study on Reasonable Mineral Processing Flow Sheet of Yunfu Low-Grade Pyrite Ores Low-grade ores in Yunfu Pyrite Mining Area were investigated, in order to find an economical, reasonable and environment-friendly mineral processing technology, which is of low consumption and high efficiency in pyrite recovering, which can ensure that the quality of pyrite concentrate product is eligible for sale and the sulfur content of the discharged tailings meets the national emission standards. A flow sheet with a classification, a jigging for coarse-grain minerals and a spiral chute separation for fine-grained minerals was adopted, and the sulfur grade and recovery of the pyrite concentrate is 35.50 per cent and 86.70 per cent respectively, while the grade of tailings is only 6.70 per cent.

Sep 13, 2010

By W. E. Oching, M. M. Ghomshei

Attracting and retaining workers in mining industry has become an uphill battle to many mining companies. As workers with significant experience retire, it is getting more difficult to attract not only new workers but also top talent to the mining industry to replace professionals exiting the workforce. To make matters worse, students’ enrolment in the post-secondary mining programs in Canada and USA is continuously declining year after year for reasons not directly linked to job market. This raises a question of how can the future needs of mining be met? This paper focuses on avenues for collaboration of industry and educational institutions to meet the current and future needs of mining. It provides effective approaches that mining institutes can engage with program advisory committees, role of the mining industry in supporting both faculty and students, how to harness the benefits of diverse workforce in the country and use of innovative technologies to attract young workers in mining. This work presents Human Resources (HR) professionals with tools that they can use to hire and retain skilled workers with strong interest to work in the mining industry. It also provides HR professionals with an opportunity to re-evaluate their restructuring practices during economic downturns as they reduce number of employees on temporary or permanent basis. The paper stresses the need of working together of the mining stakeholders including mining industry, academic institutions, First Nations’ communities and provincial(state) and federal governments to meet the current and future demands of mining as the industry experiences shortage of labour and low students’ enrolment in post-secondary mining programs. It is shown that mining educational institutes can enhance their programs and recruitments through establishing a better communication with all stakeholders. This communication can be facilitated by creating a national advisory board, to work with all mining programs at the national level for sustainable mining.

Jan 1, 2023

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior ofTiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was 150 and that of the silica in the same system was 0.02, resulting in a separation factor of 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

By M. Prud’Homme

Potash is an important natural mineral used largely as a fertilizer in the production of food and fiber. About 93 percent of all potash consumed globally is used in agriculture as fertilizer. The balance is used to manufacture potassium chemicals. Most potash is extracted by conventional underground mining methods. Solution mining is used when underground deposits are irregular and very deep. The other main production method involves the evaporation of brines in shallow salt lakes, followed by the harvesting of potassium minerals.

Jan 1, 2005

By D P. Blair

Various analysis techniques are used to determine the nature of a large seismic event that was triggered by a mass blast in an underground mine. This event was recorded by surface accelerometer arrays whose output was doubly integrated using a stable filter to determine the dynamic displacements. The peak dynamic displacements during the blast were 0.09 mm, and during its latter stages, this blast induced a seismic event having a peak dynamic displacement more than ten times larger at 1.26 mm. Polarisation analysis, based on the complex covariance matrix, showed that the seismic event was caused by movement of a known underground fault, close to the blast, which radiated most of its release motion as a shear-horizontal (SH) wave. The change in frequency content with time for the blast and seismic event was initially determined using the Fourier-based reassigned S-method. This analysis showed that the large amplitude seismic event had frequency content significantly lower than that of the blast. Nevertheless, this Fourier technique still retains the problems associated with short time windows as well as the fact that most realistic signals are non-stationary. In order to eliminate such influences, the more recently developed empirical mode decomposition (EMD) was used to obtain the intrinsic mode functions (IMF) of the seismic wave propagation. The EMD vibration analysis showed that each IMF generally exhibited distinct frequency changes throughout the blast and a significant reduction in frequency throughout the subsequent event. It is shown that most of the energy of the seismic event is contained in IMF modes 2, 3 and 4 of the SH wave; the high-frequency first mode (IMF1) contains little energy. Such modal analysis is not possible using standard Fourier methods.CITATION:Blair, D P, 2015. Dynamic displacements from a blast-triggered seismic event, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

OPENING SESSION Session Chairpersons: Dr. P.P. Jourdan & Dr. L.A. Cramer Transformation to Tackle the Challenges Facing the Ferro Alloy Industry in the Next Decade R.J. Linnell Electricity Supply in SA ? A 10-Year View T.S. Gcabashe IDC as the Catalyst for Growth in the South African Ferroalloys Industry J. Kriek Development in the Global Stainless Steel Industry V. Muñoz CLOSING SESSION Session Chairpersons: Mr. R.J. Linnell & Dr. O.F.R.A. Damm The Health of Vanadium T.E. Jones Steel Raw Materials - Nickel, Chrome, Stainless Steel Scrap and Manganese H.H. Pariser

Jan 1, 2004

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management.This paper describes the data integration requirements in a mine, concentrator and port for unification of the redundant data. The capture of the mining events, stock pile management and the metallurgical information is the base requirements for a dynamic environment to reduce the overwhelming amount of information to unified set of information. Part of any decision support program should entail these results to continuously improve the measurement system to address the costs in mine and milling the ore."

Jan 1, 2003

By X Hu, Z Pokrajcic, R Embry, P C. Stewart, J Carpenter, E Jones

Whilst the value of Pit to Plant and Mine to Mill optimisation has been proven since the 1990s, sustaining the productivity and efficiency gains typically requires ongoing test work, blast trials, plant surveys, and model calibration services. In contrast, the input to digital twin Pit to Plant or Mine to Mill optimisation is tens to hundreds of millions of tonnes of standard mine operating data. This paper presents a series of digital twin case studies from across the mine value chain, including machine learning testing methodology, model accuracy statistics and the application of Shapley Additive Explanations (SHAP) for model interpretation. These case studies demonstrate how machine learning and data fusion ore tracking connects hundreds of millions of tonnes of downstream performance data to produce digital twin models (operating models that are continuously updated and integrated into the wider Mine to Mill/Pit to Plant ore tracking system). Digital twin modelling software has been used to add block model variables for dig-rate, crusher and mill throughput, recovery (tailings grade), lump yield, product grade and product quality, fines yield and fines in lump. Block-by-block predictions are added to the geological resource and grade control block models as new block model variables. These new block model variables are used across all mine planning time horizons from life-of-mine planning to daily schedules. In addition to the materials handling and geometallurgical prediction case studies, the paper also presents digital twin case studies for drill and blast simulation and plant set point optimisation. The case studies show how digital twin simulation enables drill and blast engineers to simulate the effect of different blast designs in different blast domains using the mines operating data. Plant set point optimisation applies mathematical optimisation algorithms to the machine learning model to provide live operational decision support to metallurgists and plant operators. The digital twin machine learning case studies demonstrate a digital and sustainable paradigm for Mine to Mill and Pit to Plant optimisation.

Jun 22, 2022

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

By C. Garcia, A. Potulska, J. J. Opazo, T. Comi

"The Sierra Gorda SCM sulfide ore processing plant began commissioning in the third quarter of 2014. Located in the Atacama Desert in northern Chile, the project is an open pit mine and Copper-Molybdenum processing plant is one of the most highly-instrumented operations in the world. It is the first hard rock operation in Chile and the second in South America to utilize HPGR technology. It is a significant Molybdenum resource especially in the first five years and the Molybdenum separation plant is complex. Designed to process up to 60 million lbs. of fine Molybdenum per year, it uses the latest technology and equipment to ensure superior recovery and product quality. It also has gas handling and alarm systems to fulfil the Company’s vision of “Zero Harm”. This paper discusses the overall operation and issues relating to the concentrator start-up. These include a review of the mineral processing design, the unified process control center and management information systems, and the correlation of geological and metallurgical performance data (mine-to-mill) for use in anticipating and preparing for treatment of diverse ore deliveries. INTRODUCTION Sierra Gorda SCM is a joint venture partnership with KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining, and Sumitomo Corporation (Japan) operating in northern Chile. The Sierra Gorda open pit mine and Copper-Molybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, well-instrumented mine in Chile. This paper contains a general review of the project including geology and history. This was a very fast-track project going from greenfield site acquisition to mill start-up in 10 years. Highly-experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied. The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (see Figure 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km from the village of Sierra Gorda at an elevation of approximately 1,700 m above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic, and Escondida, to name a few."

Jan 1, 2015