Search Documents

By David Sanscartier, Elizaveta Petelina, Alexey Klyashtorin

This paper provides an overview of the radiological risk mitigation approach applied by the Saskatchewan Research Council (SRC) for the remediation of 35 legacy uranium mine sites in northern Saskatchewan where uranium exploration and extraction took place in the 1950–60s. Mining activities resulted in an irregular increase of the gamma radiation dose rate (up to 18 μSv/h). The radiological objectives for the sites include a gamma dose rate at a spot (<2.5 μSv/h above local background), and the dose rate averaged over a hectare (<1 μSv/h above local background). These objectives are generally achievable at the impacted sites through the installation of shielding soil cover. This method may be impractical for site areas with rough terrain (e.g., steep slopes) and/or difficult access. A risk assessment approach is applied to determine if these areas can be safely left uncovered or if additional mitigation measures should be implemented. The risk assessment approach is based on two factors: (i) the ambient radiation dose rates collected through gamma surveys, and (ii) actual land use data collected through various surveys of activities of local community members at the sites. Exposure scenarios based on four land uses are applied to estimate a potential annual dose load for members of the public. The estimated doses are compared with the criterion of 0.3 mSv/a recommended by the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). If the criteria are not satisfied, a mitigation plan is developed, and post-remediation gamma levels are modelled using GIS tools to evaluate the performance of the proposed mitigations. The proposed approach allows the team to optimize resources for the site remediation so that public exposure to NORM are as low as reasonably achievable after remediation.

Jan 1, 2020

By V. R. Miller

The Bureau of Mines conducted research on substitute brazing filler alloys with properties similar to those of silver filler alloys in an effort to conserve silver and reduce hazards from cadmium emissions. Experimental work was conducted first on the commercial silver brazing alloys BAg-I, BAg-la, BAg-2, and BAg-3 to establish criteria for evalu-ating the substitute alloys. Properties investigated included the wettability of copper, brass, and steel substrates, and the strength of joints made with the filler alloys. A series of experimental alloys containing 50 to 60 pct Cu, 20 to 28 pct Mn, and 17 to 30 pct Zn was prepared and evaluated, together with Cu-Mn-Zn alloys with 5 pct Pb or 2 pct Ni. Wetting properties and joint strengths were not as good as those for silver filler alloys, and the high application temperatures reduced the copper and brass base metal strengths. However, experimental alloys containing 70 pct Cu, 15 to 20 pct Mn, and 10 to 16 pct Sn had wetting and strength properties approaching those of the silver filler alloys. The application temperatures for these alloys were high-er than those for silver fillers, but not as high as those for the Cu-Mn-Zn alloys. With the Cu-Mn-Sn alloy fillers, copper alloy joint members are less deteriorated by recrystallization than when applying Cu-Mn-Zn alloys. The Cu-Mn-Sn system has potential for further devel-opment as a substitute brazing alloy system, particularly if the melting temperature can be reduced by the addition of other elements without decreasing the ductility and wetting.

Jan 1, 1983

By K. C. Dean

The combination of flotation and chemical processing methods presented in this report of the Bureau of Mines enabled treatment of typical low-grade ferberite ores from the Boulder County, Colo. area, to produce specification-grade synthetic scheelite. The overall recovery from ore to synthetic scheelite was 87 percent, based on a flotation recovery of 93 percent and a similar recovery in chemical processing. Preliminary mineral dressing studies revealed that the physical and mineralogical nature of typical ferberite ores precluded high recovery of tungsten in plus 60-percent-W03-grade products by these methods. Therefore, the flotation research was focused on attaining plus 90-percent recovery in a concentrate containing 10 percent W03. Detailed studies were made (1) to establish optimum grinding conditions for obtaining adequate mineral liberation, (2) to develop collecting and modifying reagent combinations that would enable controllable selective flotation, and (3) to define the influence of different pulp solids, temperature, pH, and time for conditioning and for the rougher and cleaner flotation stages.

Jan 1, 1961

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By Xiaowen Liu

The thermal decomposition of diaspore was investigated by thermogravimetry (TG),differential scanning calorimetry (DSC), X-ray power diffraction(XRD),infrared (IR)spectrain this paper. The thermal decomposition mechanism of diaspore was discussed according to Coat-Redfer equation. It was found that the decomposition of diaspore was carried out at 500?,and the peak temperature was 530?. The electrovalent balance of diaspore was destroyed. The previous crystal structure was changed. a- Al2O3 was obtained after thermal decomposition. The activation energy is 287KJ/mol.

Jan 1, 2006

By AIME AIME

THE Iron and Steel and Institute of Metals Divisions will meet jointly at the Statler Hotel, Detroit, Oct. 4 and 5, during the Metal Congress, Oct. 2-6. The Wire Association, the American Welding Society and the American Society for Steel Treating, together with the two Divisions of the Institute, constitute the Congress this year, and each body offers an interesting technical program. The National Metal Exposition will, as usual, be held concurrently. Visiting metallurgists will find themselves engaged in a bit of research not listed in the program-a time study of how best to exploit in a few days both the Congress and all that the place of meeting has to offer. For Detroit, the beautiful "City of the Straits," is third in rank industrially in the United States, and its great manufacturing plants offer much of metallurgical interest. This is especially true of the automobile plants which will be open to members of the various societies during the week of the Congress.

Jan 1, 1933

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975

By Frank Johnson

Between 2000 and 2006, platinum production from the South African mines expanded from 206 to 307 tonnes (DME, 2007). Most of this additional metal has come from traditional ?narrow? reef stoping, generally taken to mean stoping in working places with a mining height of less than 1,5 metres. It is well known that narrow-reef stoping presents safety, technological and ergonometric challenges (Pickering, 2007). In planning for the expansion, which is still continuing, the platinum mining industry realized that it could not simply continue with traditional methods of narrow-reef mining. Particular issues identified were: ? High labour-intensivity: caused by use of hand-held rock drilling machines, labour-intensive support installation and stope cleaning; ? Dependence on rock-drillers: this occupation is no longer an attractive one and there is a reducing flow of new recruits; ? Safety: most of the work is performed close to the new faces, where there is the greatest exposure to the hazards of falling rock.

Jan 1, 2008

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

IN 1949 the Government Printing Office issued Bureau of Mines Bulletin 468 3 and previously (in 1948) Bulletin 467 4 as part of the program under the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C., 321-325, and amendments). The two bulletins, relating to oil shale and its products, were published to present abstracts of all patents in this field from 1845 to 1945 5 or before the Synthetic Liquid Fuels Act was passed. Also, as part of this program, bulletins were published on patents relating to the pressure hydrogenation of coal e and the Fischer-Tropsch synthesis.7 The Synthetic Liquid Fuels Act was not extended beyond April 1955, but it inspired much increased activity in the field of oil-shale research, and many patent applications were filed. It is the purpose of this bulletin to abstract the patents issued in the United States, the United Kingdom, and Europe from 1946 to 1956, inclusive. A few older patents omitted in the previous bulletins have been included.

Jan 1, 1959

By T. W. Wlodek

In this paper the relative merits of shot peening, induction surface hardening, spiral-rolling, and the combination of these surface treatments, are evaluated on the basis of their capacity to increase the fatigue strength of drill steel. The S-N relations for plain car-bon steel (SAE 1080) and Ni-Cr-Mo drill steels in the as-rolled condition were determined previously, using the new Canadian method of testing drill steel introduced at the annual meeting of the Institute in Toronto in 1950 (19). S-N curves have now been determined by this method for these two drill steels in the following conditions: shot-peened and drawn, induction hardened, induction hardened and shot-peened, and spiral-rolled. ( S.R.) . The ratios of the fatigue strengths of these steels after surface treatment, to their fatigue strengths in the as-rolled condition, are compared and the most beneficial treatments are thereby pointed out. The expected range of stresses and their distribution during actual drilling operations are estimated from data available, and the mechanism of failure of drill steel in the as-rolled and surface-treated conditions is analyzed. The magnitude of the surface compression stresses and their effect on ?fatigue strength are discussed.

Jan 1, 1958

Future climate variability and change will impact on mining operations and their attendant communities. To minimise this impact, early and informed risk management is warranted. However, research into the risks posed by climate to the Australian mining industry has so far been limited. We are conducting a systematic study of the mining life-cycle to identify the main areas of vulnerability and adaptive capacity of operations and communities. This project aims to assess what adaptation activities are currently being undertaken within the mining industry and its communities across Australia and to develop a risk management approach that will aid the adaptation of practices in and around the industry, better assuring the security of people, jobs, revenue and the environment under changed or extreme climate conditions. The Canadian mining industry was recently assessed through a similar study, which found that many mining companies perceive a real risk to mining from climate change in the future, despite few companies being actively involved in managing such risk. At a workshop held by CSIRO involving mining specialists, the most vulnerable stage in the mining process in the Australian context was assessed to be production. In particular, impacts on water and energy supplies and also transport and infrastructure were of high concern. Additionally, heat stress on workers and equipment, changes in groundwater flow and increases in geohazards were also identified as important factors in the short and long term if problematic climate events become more extreme or more frequent. Risks in the planning and post-mine stages were also identified. Based on literature reviews and preliminary discussions with mining experts, here we present an initial assessment of the climate adaptation issues relating to mining and its associated communities and describe our future work plans in this area.

Jun 1, 2010

By D A. Manhire, R M. Flores

The commercial develop of coalbed methane from the Powder River Basin has demonstrated that low-rank coals can be a viable source of gas. Currently over 20 000 coalbed methane wells exist in the Powder River and it is predicted that there will be 50 000 wells by 2010. What makes the Powder River Basin successful is the thickness of the coal (in excess of 30m) as well as the low ash content (

Jan 1, 2002

By W. M. Small

From the one producing well in Austria, 7000 bbl. of heavy oil was produced and sold in 1933. This well, owned by the Raky-Danubia, was completed late in 1932 in the formation called Flysch (Upper Cretaceous or lower Eocene) near Zistersdorf north of Vienna. Two wildcats drilling in the vicinity have not yet reached the producing beds. Near Vienna, the European Gas and Electric Co. drilled five shallow wells for gas, three of which were failures. One gas well was completed for 8 million cu. ft. capacity at 260 meters depth and with a pressure of 570 lb. Another is being tested following blowouts. One gas well and one dry hole were completed in the pool in 1932. In Upper Austria, the same company abandoned one wildcat at 679 m. and is drilling at 280 m. on a second. No gas was sold during the year, but a line is being completed to supply fuel to boilers of the Vienna Electric Works. Hungary No deep drilling was done in 1933. Oil and gas concession was granted by Parliament to the European Gas and Electric Co. on Trans-danubia. Active geological and geophysical investigation is in progress. Czechoslovakia In the Gbely and Hodonin shallow fields, some 26 wells were drilled of which three were reported as failures. The total production of the fields was 111,736 bbl. of oil and 40 million cu. ft. of gas used as fuel in the field. At Vacenovice, where there were already two small gas wells, a third producer was completed at 420 m. This pool markets a small amount of gas, which is compressed and used to light railway carriages. Wildcat wells were reported drilling at about 300 m. depth at both Jasina and Telnice. One 700-ni. wildcat near the Hodonin field was abandoned. Another failure was reported completed and abandoned at 820 m. near Holic.

Jan 1, 1934

By R. M. G. Machunter

Computer models of metallurgical circuits are extensively utilised in design, and prediction of overall plant separation performance. As always, in the final optimised flowsheet design there is a compromise between the recovery of values and grade of the circuit output. This paper mathematically examines various circuit options for the generation of a heavy mineral concentrate from a generic mineral sands wet concentrator plant. Based on data derived from testwork, any particular mineral sand has a unique release curve describing the separation performance of the heavy mineral suite. Models are constructed that combine particular stage output streams as feed to other stages in various configurations. The ramifications of each option are discussed and reasons why one particular option is selected over the others examined.

Jan 1, 2005

By B. S. Spottiswoode

Lack of visibility makes it difficult for continuous miner (CM) operators to judge the desired sump depth. The resulting inaccuracies have proven to lead to significant production losses. This problem of measuring the depth of sump has been addressed in the past and a few measurement techniques have evolved. Despite various attempts, a suitable commercial depth of sump sensor does not yet exist. A system using the Doppler effect has been patented, developed and successfully tested. The method is non-intrusive and involves a beam of microwaves being projected obliquely at the roof. The received signal is analysed with respect to the transmitted signal, yielding the desired measure of displacement. Surface tests have revealed an accuracy of a few centimetres. Underground simulation tests on a load haulage dump (LHD) machine have verified the repeatability under the harsh conditions of interest. The system is presently being installed on a CM where it is to undergo a long-term performance evaluation. This paper presents the theory behind such a system, the hardware developed, the signal processing requirements and an analysis of the test results.

Sep 1, 2001

By Martin D. Conyac

A mineral resource survey of rock types and geologic structures indicates that the Mt. Henry RARE II area has low potential for the discovery of metallic minerals. Potential for coal and geothermal resources is negligible. Essentially, the Mt. Henry RARE II area has had no claim-staking activity, nor has any mine been developed in it. SETTING Size and Location The 23,000-acre (9,308 ha) "1t. Henry RARE II area (No. 1-666) lies within the Kootenai National Forest approximately 36 mi (58 km) north of Libby, Montana, in the Purcell Mountain; of Lincoln County. Irregularly shaped, the area measures roughly 5-1/2 mi (8.9 km) north-south by 8 mi (12.9 km) Past-west, and lies about 1-1/2 mi (7.2 km) south of the Canadian border.

Jan 1, 1982

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

Jan 1, 1967