Search Documents

By L. W. Vollmer

Introduction During the past three years at least fifty strings of 9% nickel steel tubing have exhibited excellent resistance .to the variably severe corrosive conditions typical of many of the sweet condensate wells in Mississippi, Louisiana, and Texas. This experience, and the characteristically outstanding performance of other ?nickel alloy steels under hydrogen sulphide corrosive conditions, dictated the selection of 9% nickel steel tubing for the second well drilled in the sour condensate Pincher Creek field of southwestern Alberta. The damaging effects of the Pincher Creek reservoir fluids on well equipment had been manifested in the discovery well by the rapid and not yet fully understood failure of API Grade N-80 tubing, stainless steel wire lines, and alloy steel fishing tools. Two very unexpected failures in the 9% nickel steel tubing, after only six days of service in production tests, instigated an extensive and continuing investigation to ascertain the probable cause of failure. This discussion presents some of the results obtained thus far which cast a little light on the perplexing behaviour of steels in hydrogen sulphide environments in general, and in sour condensate wells in particular. History of Tubing Failures Walter Marr well No. 1, in which the 9% nickel steel tubing failures occurred, produces from the Madison lime at the depth interval approximately 12,200 to 12,750 feet. The gas-oil ratio is about 26,000 and the gas contains 10.2 per cent hydrogen sulphide and 6.3 per cent carbon dioxide by volume.

Jan 1, 1952

By Carl W. Kelley

PRODUCTION in the United States of carbon black has increased from 20 million pounds per year in 1920 to over 2 billion pounds in 1964 valued at $156 million, mostly for consumption by the rubber-tire industry, which uses over 90 percent of total production. Production of over 2 billion pounds in 1964 is a 7.8-percent increase over 1963 and is the first time furnace black production has topped 2 billion pounds. Although 1964 channel black production dropped 6 percent below 1963, carbon black produced by the furnace process, which ac-counted for 92 percent of total production, increased 9 percent to 2,053 million pounds. Total shipments during 1964 amounted to 2,245 mil-lion pounds, a 7 percent increase. This growth parallels the expansion of the automotive and petroleum industries. Along with this expansion have been many advances, both in methods of manufacture and in the quality and variety of blacks available to industry. There are several kinds of carbon black, thermal, channel, furnace, lamp, and oil blacks. Until recently, channel has been the important black in rubber compounding. Following the introduction of the synthetic GR-S, and more recently of "cold rubber," it has been found that certain furnace blacks with particle size larger than that of the standard channel black give superior reinforcement. A great advantage of furnace black is that its yield per unit of gas feedstock is higher than that of channel black. The 184-million-pound increase in domestic carbon black sales was partially offset by a 37-million-pound decrease in exports. Decrease in exports especially to Europe, is expected to continue. In Europe, as in the United States, the major end use for carbon black is in the manufacture of automobile and truck tires. Although the number of automobiles in Europe is predicted to grow by about 7.5 percent per year, compounded until 1975, the increased demand will be met by a 20 percent increase in existing capacity and by the new plants being built in Europe by U.S. companies. Also) aromatic oils for producing furnace blacks are plentiful now that western Europe's chemical industry is switching to a petroleum base.

Jan 1, 1965

By Cheng Li, Yanlei Wang, Lingrui Kong, Jianxin Tang, Fang Yuan

Coal mined-out areas have a significant impact on mining safety and affect the pressure distributions of neighboring coal faces. The PFC3D software is used to study the goaf mechanical characteristics, and the core loading test verifies the rationality of the numerical simulation method. The results from the numerical modeling showed that the void ratio, particle size ratio, and particle size distribution of the rock particle sample (RPS) had a significantly remarkable influence on the compression deformation characteristics of the rock block. The parallel-bond tensile strength and parallel-bond cohesion had a notable impact on the compression deformation traits of the rock block only when the axial stress level was lower than 12 MPa. By contrast, when the axial stress exceeded 5 MPa, the effective modulus significantly influenced the compression deformation features. However, the stiffness ratio, loading rate, and parallel-bond friction angle had almost no effect on the compression deformation characteristics. Furthermore, when the stress level was less than 10 MPa, the stress–strain curves from the rock core samples’ numerical simulation and loading tests were approximately linear. In addition, the Pearson correlation coefficients of the stress–strain curves suggest that the goaf zone’s core numerical simulation results had a robust correlation with the loading test results. The findings of this study can serve as a reference for the field application of PFC3D software and safety assessments in goaves.

Jan 18, 2022

By N. S. Dalal, B. Jafari, F. H. Y. Green, M. Petersen, V. Vallyathan

"Stable coal radicals (SCRs) were detected by electron spin resonance (ESR) spectroscopy in the lung tissue of autopsied coal miners. The SCR concentrations were measured in the lung tissues from 98 coal miners with and without (a) coal workers' pneumoconiosis (CWP), (b) cancer, and (c) a history of cigarette smoking. Concentrations of SCRs were also determined in the lungs of nonminer controls. The SCR concentration was related to longer mining tenure, CWP disease severity, lung cancer, and cigarette smoking. The mean concentration of SCRs in the lung tissues of miners with 30 ± 1.4 y of coal mining exposure was 5.3 ± 1.3 x 10"" spins/g versus controls who had a nondetec¬table level (< 10 15 spins/g). An increase in disease severity was accompanied by a progressive increase in SCR concentration. A SCR concentration of 4.8 ± 0.7 x 10"" spins/g was found for simple CWP (with moderate coal macules) versus 7.8 ± 4.6 spins/g lung tissue for complicated CWP (with progressive massive fibrosis). Significantly higher (i.e., 10 x 10"") concentrations of SCR in the coal miners' lung tissues were associated with an exposure history in the anthracite regions of northeastern Pennsylvania. These results in¬dicate a possible role for SCRs in the disease process. Furthermore, ESR appears to be an adequate methodology for the quantitation of coal dust retained in the lung and for distinguishing exposures to anthracite and/or bituminous coal.THE PREVALENCE AND SEVERITY of coal workers' pneumoconiosis (CWP) differ markedly between geographic locations, mines, and coal fields irrespective of comparable levels of exposure to coal mine dust These differences cannot be fully explained by the presence of silica and other minerals in the coal mine dust.' Rank of coal is also an important factor in the pathogenesis of CWP. Equally important is that the prevalence of CWP decreases from east to west in the United States,' and South Wales miners develop more severe CWP than miners in Scotland.' However, there are conflicting reports that cast uncertainty on the influence of rank of coal in the development of CWP."" These problems are complicated but will be solved as new technology emerges and as more is learned about the disease process."

Mar 1, 1992

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco&apos;s Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott&apos;s Chino operation, and one of the world&apos;s largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983

By B Beale

Bow-tie analysis is a commonly used tool in the Major Hazard Facility sector to identify, display and control risks that have the potential to pose serious harm to personnel. It is a simple but powerful risk management tool that displays traditional risk assessment outputs as easily interpreted ‘bow-tie diagrams’. These are an effective and versatile communication format that can be applied to any type of risk (eg safety, environmental, assets etc) and as such show great benefit in managing operational hazards in mining.

May 5, 2022

By Irving Kabik

Chlorates and perchlorates, when mixed with certain reducing materials, may give a detonating explosive of considerable power. Concerning explosive chlorate mixtures, Guttman3/ states that they "have at all times fascinated inventors on account of the large amount of oxygen stored up in potassium chlorate, which can be given off so readily. When Lavoiser and Berthollet tried to make a chlorate powder in a stamp mill in 1788, they made a great show of it, and even two ladies were present. Unfortunately, after a certain amount of pounding the powder exploded and killed an official and the daughter of the Government commissary, who assisted at the experiments.***. It is interesting to observe how the same old mixtures are proposed over and over again with slight alterations only, in order to qualify for a patent. Potassium chlorate with some carbonaceous matter like charcoal, sugar, starch, glycerin, flour, or sometimes a vegetable or mineral oil and the like occurs again and again." Sprengel explosives, in which some of the undesirable sensitivity of the chlorate was minimized by coating the crystals with a liquid reducing agent, received some attention after a patent was issued to Dr. Herman Sprengel in England in 1871.4/ A somewhat similar explosive, known as Rack-a-

Jan 1, 1945

By T Berryman, C Adams, L Griesel, C Buxton

The Kalgoorlie Consolidated Gold Mines (KCGM) schedule model is used for short- to medium-term planning and scheduling at the Fimiston Open Pit Mine (the Superpit). The model bridges the gap between grade control models, which are generated one to seven days prior to mining, and the annual Resource and Reserve model update that is used for budget and life-of-mine plans. The schedule model uses close-spaced grade control data (up to 20 000 m drilled each month) as well as resource definition drilling to estimate production volumes three to six months ahead of current mining. From this, a rolling 12 week mining and processing schedule is generated on a monthly basis. As the KCGM operation is mill and sulfur constrained, the schedule model needs to be an accurate predictor of ounces as well as tonnes, gold and sulfur grades. The process must also be time efficient in order to meet monthly planning and reporting deadlines. Due to the large amount of new data generated each month, model updates using conventional interpretation and estimation techniques have proven to be impractical and too time consuming. This paper will examine the evolution of the Superpit schedule model process over time, recent improvements and the effect of different model outcomes on short- and medium-term mine planning.CITATION:Griesel, L, Buxton, C, Adams, C and Berryman, T, 2014. The superpit schedule model – A time-efficient data-driven estimation for short- and medium-term planning, in Proceedings Ninth International Mining Geology Conference 2014 , pp 397–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By S J. Schafrik, C Keles, C Schlosser, E S. Gilliland, A K. Louk, N S. Ripepi, S Keim, J Amante, E Diminick

Three legacy coalbed methane production wells have been converted to injection wells for a one-year carbon dioxide (CO2) injection test to evaluate the potential for CO2 storage in the coal reservoir and the potential for enhanced gas production at offset wells. The injection reservoir is composed of 15–20 individual coal seams with an average thickness of 30 cm (1.0 ft), spanning a depth range of approximately 240 (800 ft) to 670 m (2200 ft).The monitoring program for this test includes gas and water sampling of the three injection wells, three dedicated monitoring wells and approximately 20 offset production wells. Key technologies used for monitoring the study area include time-lapse GPS and interferometric synthetic aperture radar (InSAR) acquisitions for surface deformation measurement, a 28-station buried passive microseismic monitoring array, real-time downhole pressure and temperature sensing and perfluorocarbon tracer fluids, which will be injected with the CO2 stream. The schedule for the monitoring program includes pre- (baseline), during- and post-injection data collection. This schedule will allow data to be analysed for time-lapse changes and trends, which are important for understanding the migration of gas and fluid phases in the reservoir – including CO2, methane, other hydrocarbons and water – and for observing the changing distributions of reservoir pressures and stresses.The results of the monitoring efforts for this study have implications for monitoring mining operations. The combined use of GPS and InSAR geospatial data to evaluate elevation changes across and beyond the study area may prove to be an accurate option for measuring surface deformation, including mining-induced subsidence, in unstable terrain. Long-term microseismic monitoring using high-sensitivity instruments has several applications in mining operations, including rock stability monitoring, production monitoring and miner location detection during emergencies. Tracer studies and short-term microseismic monitoring used to assess methane extraction can also be used to develop and optimise degasification systems for underground coalmines.CITATION:Gilliland, E S, Ripepi, N S, Schafrik, S J, Schlosser, C, Amante, J, Louk, A K, Diminick, E, Keim, S, Keles, C and Karmis, M, 2015. Monitoring design and data management for a multiwell CO2 storage/enhanced coalbed methane test in a stacked coal reservoir, Buchanan County, Virginia, USA, in Proceedings Third International Future Mining Conference, pp 47–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By J. A. Gay

BRITISH success in extracting significant quantities of germanium from gas works flue dusts has been one of the prime forces in promoting similar research in the United States. Pittsburgh Consolidation Coal Co. and Pennsylvania Coal & Coke Co. are two of the larger U. S. firms with germanium from flue dust research programs. British interest in germanium started in 1933 when V. M. Goldschmidt reported that some coals from the Yard Seam of Northumberland and Durham contained 30 to 50 ppm of germanium.

Jan 8, 1953

By R. J. Matetic

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX&apos;s) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it&apos;s influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the fieldsite. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 2010

By J. W. Perez

Raw coal will often break intragranularly in either a completely random way or in a differential mode where one species will have a different rate of breakage than another. Locked coal-ash and coal-pyrite particles can also break by the preferential detachment of one species from another along zones of inherent weakness in locked particle assemblages. The mode. cf breakage is largely a function of the nature of the feed, but it is also influenced by the comminution device and the operating variables. Evidence of breakage of particles in the various modes is seen in the crushing of raw coal and middlings particles with a rotary beaker, jaw crusher, rolls, hammer mill and rod mill. Evidence from the literature indicates the detachment mode is often important for coal, ores and metallurgical products. Further confirmation comes from the crushing of a specially prepared &apos;ore&apos; of sized magnetite in plaster of Paris.

Jan 1, 1988

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

The Marvel Loch Operations (MLO) plant was treating ores from up to six MLO sources and in addition needed to blend externally sourced ores with its own ores. This presented a metallurgical accounting dilemma, which was subsequently addressed by the design, implementation and testing of an automatic sampling system. The MLO automatic sampler was well designed and has been the subject of previous internal and external reviews. The sampling action is fully automated and the unit is essentially self cleaning particularly when sampling primary ores. The purpose of this paper is to document the rationale behind the design, the specific details of the sampling station, its use for ore purchase purposes and an assessment of the sampling system to meet the needs of the operator.

Mar 1, 2010

Conventional treatment of oxide and oxidised sulphide minerals by flotation involves the use of sodium sulphide for sulphidisation. Sodium sulphide is generally applied in a "slug" dosing fashion with manual regulation. However, it is recognised that "over addition" or "under addition" of sulphidising reagent can result in poor flotation recoveries. Thus, control of sodium sulphide additions is an important aspect of a sulphidisation circuit, both commercially and metallurgically. In any plant where the flotation feed is "constant" it is possible to operate at a constant rate of addition of sodium sulphide. In actual plant practice, however, it is difficult to maintain a truly constant feed for any reasonable duration because this implies not only a constant feed-rate, but also constant mineral composition and particle size range. These factors can vary significantly and ideally require corresponding variations in the additions of sodium sulphide to maintain optimum recoveries. To cope with variations in the feed, it is essential to have automatic rather than manual regulation of the sulphide reagent addition. The CPS process achieves this control by utilising a sulphide ion-selective electrode as a control instrument in sulphidisation. The CPS process which uses a selective electrode, enables the sulphide ion concentration in the flotation pulp to be monitored and controlled continuously throughout the stage of sulphidisation.

Jan 1, 1989

By P Jackson, J Rea, M D. Goodz

The Morning Star Gold Mine has operated over a 101-year period, producing gold from narrow quartz veins and sulfide stockworks hosted mainly within a dioritic-gabbroic dyke. The deposit has been developed over a vertical depth of 980 m with drilling extending the vertical depth to greater than 1200 m. Currently there is a total Inferred Resource of 4.6 million tonnes at a grade of 6 g/t for 910 000 ounces of contained gold resources, which comprises an underground project and a surface project. Significant variation exists between the grade of drill core intersections and that observed in face sampling and subsequent production reconciliation (250 - 650 per cent). Studies were carried out on ten major production reefs, where the grades of drill intercepts were compared with face samples collected during development and mining. The implications of this study have been used as justification to assign production or stope/development grades where applicable to resources that are direct extensions of the historical development headings. Grade assignment and its impact on sensitivity for gold resources are detailed and show a 40 per cent variation in the gold resource, depending upon whether a production or calculated stope grade is used in grade assignment for the major reef deposits. Recent diamond drilling has intersected approximately 40 new gold bearing quartz reefs and sulfide zones that contain all the key mineralogical and structural indicators, and traditional large variations in gold grades similar to the historical major production zones. The implications of grade factoring and grade assignment are the greatest challenges confronting the resource estimation team in defining grade for these new zones. Grade assignment is seen as a method of balancing known historical production observations with the irregular grade distribution inferred from drill core assay results. Ongoing mine development and bulk sampling works are planned to validate the grade assignment process. The first stage of this process is the trial mining of the newly discovered Maxwell Reef (MR). The stope drawpoints were completed in August 2008 and the MRS1 stope is scheduled for completion in September. The stope reconciliation results will be presented at the October 2008 conference.

Jan 1, 2008

By Vladimir Panjkovic, Ostrovski. Oieg, Campbell Cripps Clark, John Truelove

"Effects of properties of raw materials and blast on the performance of an iron bath reactor have been examined by a mathematical model. The model consists of three modules: 1) chemical reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, post-combustion ratio and heat-transfer efficiency, temperature and composition of the off-gas, and slag and metal chemistry.IntroductionOne of the anticipated advantages of smelting reduction over conventional ironmaking is the use of lower-grade raw materials. In this work, the effect of-properties of raw materials on the performance of an iron-bath reactor is examined with a numerical model. The model is also used to assess the effect of properties of the blast (flowrate, temperature and oxygen enrichment) and ejected droplets (generation rate, size and ratio of total weights of slag and iron droplets) on the key parameters of the process. In the process coal, oxygen, ore (which may be partly prereduced) and fluxes for specified slag composition are charged to the bath. Slag and iron droplets are ejected from the bath into the gas phase, where they are heated before returning to the bath. Iron droplets undergo decarburisation and reoxidation with CO2 and H2O. Dust is also generated from the bath, and oxygen or preheated air for post combustion is injected from the top of the vessel.The model consists of three modules: 1) reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The structure of the model and the data exchange between the modules are shown in Fig. 1. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, postcombustion ratio (PCR), heat transfer efficiency (HTE), off-gas temperature and composition, slag and metal chemistry, and rates of decarburisation and reoxidation of the iron droplets."

Jan 1, 1996

By E Widzyk-Capehart

The mines of the future can be envisioned as complex, large-scale technological systems being operated remotely from few centrally located (major cities) operating centres and skeletal crew stationed at the site. These systems will require remotely located human operators to constantly adapt to new and unforeseen system and environmental demands. In addition, the remote operators will need to match system properties to the changing demands and operational conditions, ie must be able to handle the ‘non-design’ emergencies, because the system designers would not have been able to foresee all possible scenarios of failures and provide automatic safety devices for every contingency. Therefore, it is highly important that the operators’ job, which involves problem solving and decision making at the workstation level, is facilitated by the proper interface designs. This paper argues that decision support systems and thus human-system interfaces for the mines of the future should be developed based on the principles of human-system integration that take into account human information processing and cognitive abilities. The information presented to the operator must support the operator in taking appropriate action through a human-system interface designed according to scientific principles of User Centred Design. A case study is presented where an iterative design process was used by CSIRO researchers as an evaluation method involving users (control room operators) at several stages of the user interface design in order to correct any design inadequacies as they emerged. This process allowed the designers to identify any usability issues before the user interface was fully implemented, which subsequently enabled the control room operators to easily adapt to the new interface and carry out all designated tasks in a timely and effective manner.

Nov 22, 2011

This report describes the results of a program to design, procure, install, and evaluate a multi-channel underground telephone system of modern design in the Sunshine Silver Mine near Wallace, Idaho. Although the evaluation portion of the program was deleted, this report contains a cost benefit analysis for such a system using estimates of operational data for the Sunshine Mine. The results show a centrally switched telephone system of conventional design with ruggedized phone enclosures and special environmentally sealed dial pads to be the most economical.

Jan 1, 1982