Search Documents

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By Donald C. Clark

The Blasting Contractor as an Insurance Risk involves a discussion of changing times in the insurance market and changing methods of operation in the construction industry. Since the advent of Internal Revenue Service~1 and Occupational Safety and Health Act~2 regulations by the Federal Government in the early 1970's, operations have changed. Many small users of explosives have discontinued any use in favor of subcontracting the drilling and blasting to specialists. This change in operations along with the change in the insurance market has created coverage problems which is the subject of discussion of this paper. Although no definite conclusions are reached, it is an attempt to promote understanding and further the efforts toward equitable solutions.

Jan 1, 1977

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011

By Oscar Marreros D

Luego de que Centromin realizara los estudios de los taludes del tajo Raúl Rojas a través de los métodos Janbu y Bishop, se recomendó que el talud final del lado oeste se mantuviera con el diseño planeado a 45° puesto que así lo requerían las instalaciones de la concentradora al límite del tajo. Posteriormente, este diseño se eliminó porque se comprobó la estabilidad del talud estudiado. En ese sentido, el presente texto señala los nuevos análisis de mecánica de rocas para la estabilidad en cuña, donde se eliminan los riesgos de seguridad de la concentradora y se disminuye la cantidad de desmonte.

Apr 1, 1991

By J. E. Hawley

"IntroductionA STUDY of the trace elements in the ash •of coals from nine seams in the Sydney coalfield, Nova Scotia, was undertaken at the suggestion of Dr. W. A. Bell, Geological Survey of Canada, as a part of a larger study of these and other Nova Scotia coals being made by the Geological Survey and the Nova Scotia Department of Mines under the direction of Dr. P. A. Hacquebard.The main purpose of this investigation has been to •determine if a knowledge of the trace element distribution might be of assistance in the recognition of individual seams, the distinction of which is not always easy or positive in folded and faulted strata by ordinary stratigraphic and structural means.The study has been so conducted as to afford information on the variation of trace elements in individual petrographic intervals or divisions in each of the seams examined, intervals determined by Dr. Hacquebard on the basis of their banded ingredients, vitrain, clarain, durain, fusain, etc, as observed under the microscope in polished sections. The results, as well, indicate the trace element composition of the coals of the area as a whole, and quantitative data for fifteen elements are given, along with concentrations of thirteen other elements, stated in terms of intensity ratios. Data on distribution of germanium, though considered here along with other elements, are dealt with elsewhere*."

Jan 1, 1955

By Abegail Endraca, Allan Sebastian, Andrew Raine, Allan Patdu

The project involves the construction of a new aqueduct tunnel by an Earth Pressure Balance TBM tunnel for the Novaliches-Balara Aqueduct No 4 (NBAQ4) project in Metro Manila. It comprises a 7.3 km long and 3.1 m internal diameter tunnel that can deliver up to 1,000 MLD of raw water and the tunnel passes under urban residential and urban populated areas adjacent to and along Commonwealth Avenue. A new reservoir intake structure was constructed in the La Mesa reservoir by a cofferdam and the TBM breakthrough connected the reservoir to the outlet surge shaft structure and the downstream pipe network system connecting to the Balara Water Treatment Plant. The TBM incorporated a double articulated head configuration to allow tight 80 m radius curves to navigate some of the difficult alignment considerations. The alignment passed very close to some existing foundations for MRT7 and needed to clear several tight curves to remain within government land ownership. The project excavated through the local Guadalupe weak rock formations and there was minimal ground movements observed as a result of the work.

Jun 13, 2023

By Raymond L. Lowrie

Deregulation, as authorized by the Energy Policy Act of 1992 (PL102-486) allows free-market competition in the electric-utility industry. As the act unfolds, though, uncertainties abound about the type, degree and direction of impacts throughout the affected economy — from fuel suppliers to electricity generators and from power distributors to energy consumers. Instead of having a familiar base of captive customers and electricity prices fixed by negotiation with state public utility commissions, utility companies are preparing for open, free-market competition. They are looking at all areas, including fuel supply, to cut costs to remain competitive. Humorous anecdotes are told about utility companies shunning insiders for senior executive positions. Instead, they are opting for people from the telephone or other industries with deregulation experience. And there are light-hearted stories about a trend away from traditional electric-company names, such as the name of a city or state followed by Edison or Power and Light, to space-age names, such as Ameren, Entergy, Illinova or Unicom. No one wants to be left behind or be perceived to be left behind.

Jan 1, 1996

By H. S. Sichel

"The valuation of diamond ferous deposits depends on (i) the density distribution, (ii) the size distribution of stones and (iii) the selling price structure prevailing at a particular time.In the density distribution the stochastic variable is defined as the Dumber of individual stones found per sample unit irrespective of the stone size. The density distribution is discrete and allows for barren sample units.As diamonds often occur in clusters, a Poisson mixture distribution is derived which is entirely new, as existing discrete distributions cannot represent the stone number frequencies found in nature.For the sizes of diamonds, which are measured by weight, a new compound logarithmic normal distribution is developed.Combination of (i), (H) and (iii) leads to a meaningful appraisal of diamond ferous ground expressed in monetary value per production unit of mining.Finally, confidence limits are calculated which allow for inference from sampling to recovery."

Jan 1, 2014

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015

By Alcides José de Lucena Silva

Tudo parece ir bem com o sistema de automação antigo, mas sabe-se que conforme o tempo passa, uma falha neste sistema pode acontecer e/ou uma falta de sobressalente por obsolescencia. Modernizando o, conseguimos realizar a migração de forma escalonada, administrando tempos e orçamentos, inclusive aproveitando parte da arquitetura existente. O trabalho em questão irá demostrar o desenvolvimento da migração do sistema de automação do Alto-forno#3, incluindo troca de controladores, segregação das redes de automação e substituição dos supervisórios, aumentando a capacidade do sistema e tornando o mais robusto e confiavel para manter um dos principais ativos da CSN funcionando atualizado até o fim da sua vida util.

Aug 17, 2017

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

Crushing Plant Process Optimisation Design of processes in order to find the most efficient solution to a specific task is a difficult problem. Often the number of solutions are large and the optimal solution is therefore difficult to identify. Crushing plant process design is no exception from this statement. In order to find the best solution issues like equipment selection and process configuration must be mastered. The solution must both be technically feasible and preferably have a low operating cost. Since crushing plant design is a complex task with a large solution space it is basically impossible to master without a specialised tool. For a long time simulation softwares have been used to assist in the design process. These tools only give answers for how a user defined plant will operate. There are no tools with capabilities to consider different design options in order to determine what the most efficient solution looks like. In this paper a method for crushing plant design optimisation is presented. The novel method utilises a combined optimisation routine and expert system in order to find the most cost efficient solution to a given process task. The user will only need to define the feed material properties, the process capacity, and the end product requirements. The developed system will find the solution lowest production cost per ton.

Sep 13, 2010

By D. E. Nash

Environmental compliance programs for mining companies are not only important management tools, but can deflect serious civil and criminal penalties if violations of environmental laws do occur. The paper discusses the legal foundation for such programs and their basic structure.

Jan 1, 2001

By L. A. Pursell

Environmental constraints can both delay and raise the cost of a major plant addition, often requiring a complete reevaluation of the plant site and the proposed project. In this case history, steps are presented which were followed in applying for environmental permits for a major addition to a lime plant. Methods are described for determining expected emission increases and for selecting the best control technology for each source. The description progresses through pre-application conferences with control agencies, the formal application procedure, computer modeling the air quality impact, and the methods followed in obtaining a favorable determination.

Jan 1, 1983

By Bengt T. Andersson

Outokumpu Consulting Engineers, Outokumpu Oy SF-02200 Espoo 20, Finland This paper describes experiences from some operating non-ferrous flash -smelters and focuses on the advances in smelter byproduct and gas treatment engineering design. In this context a summary is given of the specific technical and economic benefits achieved-by flash -smelting technology and oxygen enrichment. The paper will also briefly outline a few new process and equipment developments.

Jan 1, 1983

By David E. Siskind

"This report describes recommended vibration monitoring and assessment practices at blasting sites.Intended is regular monitoring, tracking of trends, responding to complaints of alleged damage, and the technical and data aspects of addressing lawsuits."

Jan 1, 1999

By R. J. Pokora

This Bureau of Mines report is an applications manual that can be used by the nonmetallic mining industry for guidance in installing noise control materials into crushing and screening plants. These noise control modifications were installed and successfully tested at three operating quarries. This report identifies the major noise sources that can be encountered in crushing and screening plants, and discusses the applicable noise control materials and techniques that a plant operator can utilize on a retrofit basis to reduce equipment noise.

Jan 1, 1984

By C Smith, R I. Maczkowiack, P D. Erskine

Open cut coal-mining has been conducted in the Bowen Basin region of central Queensland for almost five decades, and has disturbed an estimated area of 140 000 ha of agricultural land until 2011. Approximately one-third of the area disturbed by mining has been rehabilitated to pastures or bushland. However, none of the rehabilitated land has yet been assigned a specific end-use. This research project develops an approach for assessing end-use risks for the regionÆs mined land, and develops risk assessment models for selected end-uses. First, a web-based survey of stakeholders was used to identify risks to be assessed. The risks identified were surface erosion, subsurface erosion, bushfires, weeds and feral animals. The survey also identified possible end-uses of bushland and grazing. Second, conceptual risk models were developed based on the risk assessment concepts of likelihood and consequence specified in the Australian and New Zealand risk assessment standards. Likelihood was modelled using site characteristics and management factors that influence the occurrence probability of risks (eg surface erosion), while consequence was modelled using a set of site condition indicators and condition thresholds (changes in root-zone water-holding capacity, soil erodibility, vegetation ground cover and soil organic matter and transition probability to a non-preferred ecosystem type).The factors influencing likelihood and consequence for each risk have been integrated using Bayesian networks. The next step in model development is to parameterise the Bayesian networks using existing equations, empirical datasets, or expert opinion where data are not available. The parameterised models will be used to assess grazing and bushland end-uses against erosion, bushfire, weed and feral animal risks for rehabilitated mined land sites, with the purpose of identifying the relative risks associated with each end-use, and the landform design specifications and land management practices under which end-use risks are minimised.CITATION:Maczkowiack, R I, Smith, C and Erskine, P D, 2012. Risk assessment models for post-mining land use, in Proceedings Life-of-Mine 2012, pp 33-42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Gordon H. Dechman

This report presents the concept, design, and testing of a sonic velocity monitoring system for the early detection of slope failure in open pit mines. The heart of the system is a device for producing reproducible sonic signals in rock. Because changes in the velocity of sound through rock near the top of the pit wall are a measure of extent and rate of fracturing of the rock, velocity histories obtained from periodic, automatic sonic velocity surveys provide positive information about developing slope instability.

Jan 1, 1976