Search Documents

The Molycorp operation at Mountain Pass, California, is unique in that it is the only place in the world where bastnasite is mined. The orebody is a metamorphic carbonatite; the mineral of importance is bastnasite, a fluocarbonate containing principally cerium, lanthanum, neodymium, and praseodymium, with small amounts of samarium, gadolinium, and europium. In addition, appreciable quantities of barite, calcite, and strontianite are present. Molycorp had mined and processed the bastnasite ore since the early 1950s at a rate of about 100 tpd by a unique hot flotation process in a plant originally used for cyanidation of gold ore. The concentrate was primarily used in high quality glass polishing, lighter flints, ceramics, and in specialty steel making. Then in the early 1960s, Molycorp and the Colorado School of Mines Research Foundation developed a solvent extraction process to recover europium from the bulk rare earth concentrates. In 1965 a new SX plant was constructed to produce this material for use as a red phosphor in color television tubes. Because of the demand for this material, a new 500 tpd concentrator was designed and constructed in 9 ½ months. Then, because of a sharply increased demand for europium, the plant was expanded to 1200 tpd only four months after completion of the original construction. The crushing section of the new plant was designed similarly to those portable units used in road construction and arrived on the site in ten major pieces. Foundations were concrete piers; and after their completion, the entire crushing plant composed of primary and secondary crushers, conveyors, and a screen was erected in fourteen days by a crew of ten men assisted by a mobile crane. Pit-run ore is loaded into 35-ton trucks by a 7 yd (5.4 cu m) loader, trans- ported to .the crushing plant, and dumped into the 65 -ton concrete pocket. A 42 in. by 20 ft (1.07 m by 6. 1 m) apron feeder feeds ore to the 30 in. by 42 in. (760 rnrn by 1070 mm) single toggle jaw crusher. Crushed ore is trans- ferred by a scissors conveyor to a 5 ft by 14 ft (1.52 m by 4. 27 m) double- deck screen which produces a final ¾ in. (19 rnrn) product with the oversize being treated in a 4 ¼ ft (1. 3 m) standard cone crusher. Cone crusher product is returned to the first scissors conveyor to join the primary crusher product. Dust collection is by a wet scrubber, and an operator's control room is located to overlook the primary. The entire crushing is in the open, and a 30-ton mobile crane is used for maintenance. Molycorp’s two-stage crushing plant is an excellent example of functional design for a small mining and milling operation.

Jan 1, 1978

By P. Michael

Proponents of geomorphic mine land reclamation have criticized current reclamation practices in the coal fields of steep-sloped Central Appalachia as too narrowly focused on civil engineering principles and neglectful of the functional and aesthetic benefits of reclaiming mine sites in ways that mimic natural landforms and drainage patterns. They observe that current mining and reclamation practices are radically transforming the mountain-and-valley terrain into gigantic flat plateaus and, in doing so, disrupting the beauty and ecology of the natural landscape. Instead of designing and constructing linear or planar surfaces and unvarying slope gradients during the reclamation process, they recommend ?landforming,? i.e. the adoption of curvilinear, compound slope forms that blend well with the surrounding physiography and represent the result of naturally stabilizing geomomorphic processes. The authors feel that the concept of geomorphic mine land reclamation is sound, however, its application to the Central Appalachian coal fields faces significant--albeit not insurmountable--challenges. They include: (1) existing reclamation enforcement regulations that are focused on civil engineering principles and not explicitly supportive of geomorphic methodologies; (2) regulatory agencies? current intent to limit the down-gradient reach of excess spoil fills in order to allay disruption or burial of natural streams; (3) actual or perceived increases in reclamation costs; and (4) the challenge of designing and constructing ?natural? landforms that are mature and stable in an otherwise youthful, erosional landscape.

Jan 1, 2010

The Mount Isa mine in North West Queens- land produces a total of nearly 10 million t/yr from separate copper and silver lead zinc orebodies. Sampling information is mainly obtained from diamond drilling on 30 to 40 metre centers in both types of orebodies. For the copper orebodies the majority of the core is analysed for copper content using a non-destructive bulk analyser developed by the Australian Atomic Energy Commission. The diamond drill core in the silver lead zinc orebodies is usually sam- pled as sawn half core and assayed in the com- pany laboratory using a variety of methods dependent upon the level of metal content and/or the elements required. Underground development is sampled where additional information is required to improve the ore reserve estimate. The copper areas are sampled using a standard 2.0 m by 2.0 m chip sample of the wall. The chips are taken on a 250 mm spacing. Lead areas are sampled using a 100 mm wide by 4 mm deep channel over intervals determined by the area geologists. The massive, irregularly shaped copper ore bodies are mined as large sublevel open stopes and pillars. Ore reserve estimation on both a production unit and global scale is routinely carried out using a geostatistical system developed in-house and running on a Sperry 1100 mainframe computer. Copper grade, tonnes and the Kriging var- iance are estimated at points on a user defined grid. The Kriging program uses 10 m assay composites from diamond drill core and underground chip samples. One average (rela- tive) variogram is used throughout the main copper orebodies. The validity of using an average variogram was verified by the original geostatistical study undertaken in the late 1970's.

Jan 1, 1987

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

By Jamie Delgado, Marco Arelano

The changes of bench angles in an Open pit mine has a strong economical impact in the “mining business”, particularly in its cash flow related both to the decrease as well as to the increase of the global bench angle or the inter-ramp angle. The global vision of bench optimization process currently developed by Compafila Minera Zaldivar (CMZ), includes the interconnection of different processes driving to the completion of the designs. Thus five very influential areas are recognised such as: (1) The physical Surrounding terrain, (2) the strength parameters, (3) the observational model, (4) the acceptability criteria and (5) the operational considerations. One of the important variables affecting this process is Drilling and Blasting (D&B). Increasing the bench angle requires to optimisation of D&B. To achieve this efficiently controlled sub processes must be defined. Three (3) steps can be defined: (a) design parameters, (b) explosive energy distribution and (c) operation results. To control and improve said steps quantitative evaluations of D&B must be performed. One valid evaluation is the “near field vibration monitoring technique” (at bench level). With the application of damage criteria, measurements and modelling of particle velocity a proper definition and optimisation of stages (a), (b) and (c) was achieved, The use of this methodology has enabled to CMZ to successfully increase the inter-ramp angle in three degrees thus obtaining a saving of US$ 36 million in the waste material removed. Also, the efficient control of the bench slopes has resulted in the improvement of the fragmentation operational results. This has resulted in a 26Oh increase in the ore processing by saving energy in the primary crusher due to its performance improvement.

Jan 1, 2001

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By R. Pressacco

"IntroductionAgrium’s history in fertilizer production and marketing goes back to 1931. Today, Agrium Inc. is a world leader in the production, distribution, and marketing of fertilizers and related products to the agricultural industry. Agrium is the largest North American producer of nitrogen fertilizers, a major producer of phosphate and potash fertilizers, and a world leader in fertilizer wholesale distribution and retail marketing. The mine at Kapuskasing is located some 40 km southwest of Kapuskasing, Ontario (Fig. 1). It has been developed to supply high-quality, low-cost phosphate rock to the company’s Redwater, Alberta facility, where it is an ingredient in ammonium phosphate fertilizer production. The Kapuskasing mine is the only phosphate mine in Canada and will rank as one of the highest-grade phosphate mines in the world (Clark and Duncan, 1999). Apatite is the principal ore mineral mined at the Kapuskasing Phosphate Operations.GeologyThe first record of exploration in the area was from a program executed by Continental Copper Mines in 1955 which evaluated the magnetic anomaly located in the Cargill and Cumming townships for its base metal potential. Intermittent exploration of the base metal potential of this magnetic anomaly continued in the following years, until the phosphate potential of the area was first examined in 1974 by International Minerals Corporation which recognized the presence of a layer of apatite sands overlying the carbonatite host rocks.The local geology consists of a core complex of multi-phased carbonatite rocks which are surrounded by a ring of pyroxenite, and have provided a U-Pb age date of 1907 Ma ± 4 (Sage, 1988). These two rock types are in turn situated within quartz diorite gneisses that form a large portion of the Kapuskasing Structural Zone (Fig. 2). The carbonatite host rock is sub-divided into two sub-types: sovite and rauhaugite. The sovite is a medium- to coarse-grained, white, banded rock in which calcite is the dominant carbonate species and it includes accessory minerals such as phlogopite, magnetite, clinohumite, apatite, olivine, pyrrhotite, and amphibole. Apatite can reach 15% abundance in this rock type (Sage, 1988). In sharp contrast to the sovite, the rauhaugite appears as a massive, fine-grained, dense, beige to tan-coloured rock in which dolomite is the dominant carbonate species. Phosphate values can range to 14% P2O5 in the rauhaugite."

Jan 1, 2001

By Cuim R., M. L. Li

Fankou Lead-Zinc Mine produced pyrite concentrate (P.C.) from the zinc tailings by rougher and scavenger flotation before 2010, with the averaged S grade of 40.54% at recovery of 79.34% ( to the feed of S circuit). On the one hand, the economic value of P.C. increases with its purity, on the other hand, when the S grade of P.C. feed to sulfuric acid manufacturer is over 47%, the pyrite cinder can reach a high Fe grade of 62% which can be directly sold as iron concentrate. On this background, engineers in Fankou Mine set the P.C. with S grade of 47% as target. The direct way to reach that goal was to clean the rougher P.C.. Lots of cleaning flotation tests were conducted and the compromised strategy was to produce two ranks P.C. with the S grade of 47% and 38% at the recovery of 44.20% and 36.17%, respectively. The dual-product flowsheet was successfully industrialized in 2010. In order to further improve the quality of P.C., gravity separation was introduced into the flowsheet. The numerical simulation and separation tests were performed to evaluate the beneficiation and classification performance of hydrocyclone as it treated the rougher P.C.. It was shown that the underflow of hydrocyclone could addressed the S grade of 47%, and the finer size overflow could also be enriched to P.C. with S grade of 47% by flotation, due to the contained pyrite with well liberation. That is to say, with the ingenious addition of hydrocyclone to treat the rough P.C., single P.C. with S grade of 47% could be achieved. The new flotation-gravity separation flowsheet was commissioned to produce the high quality P.C. at the end of 2013. The averaged S grade is 47.20% at recovery of 82.26% in 2014. The two steps flowsheet improvement maximizes the enterprise benefits and leads to simple utilization of Fe in pyrite in downstream industry.

Jan 1, 2018

By A. Rao, J. A. Davidson, B. L. Jones, K. W. Bowes, D. Craib

Supported by ANSTO, Groundwater Science and Inception Consulting Engineers, Boss has embarked on a series of technical projects aimed at reinforcing the Project’s capability to meet its export permit production capability. This paper will focus on three aspects of this technical program: Reducing the cost of resource expansion through smart use of low cost, surface target generation techniques; Improving the rate of uranium leaching and solution stability (gypsum, jarosite) through lixiviant chemistry modifications; and Development of an ion exchange (IX) process to increase production capacity, and integration of IX and the current solvent extraction circuit with the existing uranium precipitation and product preparation circuits.

Jan 1, 2020

By M. B. Kime, A. T. Kaniki

"Grinding tests were conducted on an oxidized copper-cobalt ore using a pear-shaped ball mill. Twelve mono-sized ore fractions were prepared and wet ground batchwise. The mill was run for 0.5 to 30 min intervals. The shortest interval provided data more closely related to the breakage function (B) because less secondary breakage was hypothesized. Some selection function (S) and B parameters were determined. Remaining parameters were estimated using a population balance model simulator. To evaluate the kinetics model, an unsized ore sample was also milled. Predicted and measured particle size distributions (PSDs) agreed well, suggesting that S and B parameters can be used for continuous operation mass balances.RÉSUMÉ Des essais de broyage ont été menés sur un minerai oxydé de cuivre-cobalt à l’aide d’un broyeur à boulets piriforme. Douze fractions de minerai de dimension unique ont été préparés et broyés en voie humide en lots. Le broyeur était mis en route à des intervalles de 0,5 à 30 minutes. L’intervalle le plus court fournissait des données plus étroitement liées à la fonction d’abattage (B) car d’après l’hypothèse avancée, le besoin d’abattage secondaire était moindre. Certains paramètres de la fonction de sélection (S) et de B ont été déterminés ; les paramètres restants ont été estimés à l’aide d’un simulateur de modèle d’équilibre de population. Pour évaluer le modèle de cinétique, un échantillon de minerai non calibré a également été broyé. Les compositions granulométriques (PSD, de l’anglais particle size distributions) prévues et mesurées correspondaient bien, ce qui laisse penser que l’on peut se servir des paramètres S et B dans le cadre d’équilibrages massiques en fonctionnement continu. INTRODUCTIONSize reduction of solids is a very energy intensive and highly inefficient process. It consumes approximately 5% of the electricity produced worldwide (Rhodes, 1998), and more than 50% of the total energy used in mineral processing plants (Walkiewicz, Lindroth, & Clark, 1996). An increase in grinding efficiency can therefore result in significant reductions in operating costs. This often amounts to determining the optimal design configurations for milling an ore sample in a laboratory mill under standard conditions. Prior to optimizing the milling stage, the requirements for downstream processing in terms of particle size distribution (PSD) need to be understood because low liberation and overgrinding will lead to future problems. Once this is done, it is also important to clearly understand the breakage properties of the ore. The kinetics of size reduction in tumbling mills are often determined using two probabilistic functions: selection and breakage (Austin & Luckie, 1972). Knowledge of the selection and breakage functions also enables the prediction of the PSD for a given ore sample."

Jan 1, 2017

This Bureau of Hines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

By G Gopinath, R Balachander, H S. Venkatesh

This paper describes in detail the controlled blasting adopted and the measurements undertaken for the successful excavation of large twin tunnels under a shallow cover for a six-lane highway project in India. The tunnels are D-shaped, each 15 m in diameter, and the cover between the tunnels and the existing railway track was about 14 m. These twin tunnel tubes were characterised by two separate three-lane carriageways for each direction of traffic, and were planned with about 25 m of reinforced cement concrete (RCC) portals at the entrance and exit of the tunnels. The major challenge of the project was the blasting of tunnels in rock below an operating railway line. As the tunnels approached the area below the railway line, the ground vibrations were monitored vertically above the blasting faces and on the railway track sleepers. Vibration intensities between those generated from tunnel blasting and those from the movement of the trains were compared, and it was found that the vibrations from blasting were lower than those from the moving trains. Though the permissible level of ground vibration based on the Indian Standard (IS) code happens to be 70 mm/s, the maximum charge per delay was calculated restricting this limit to 50 mm/s. This ensured that the vibrations in the vicinity of the railway tracks never exceeded the prescribed limit of 70 mm/s. The surface ground settlement before and after the blasts were also measured using an optical levelling instrument, which confirmed that there was no significant impact on the surface movements due to blasting. Extensometer readings inside the tunnels showed that there was no deformation in the tunnel. These twin tunnels are now operational and are providing faster connectivity with safety.CITATION:Gopinath, G, Venkatesh, H S and Balachander, R, 2015. Controlled blasting for twin tunnels with a shallow cover under an operating railway line, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022

By John E. Conley

The great demand for metallic aluminum for the prosecution of World War II caused the consumption of bauxite, the common ore of aluminum, to increase greatly. Prior to the war, the domestic deposits 'of bauxite, which occur chiefly in Arkansas and less extensively in Georgia, Alabama, and Mississippi, supplied only: about 30 ,percent of the ore required for aluminum-metal production and approximately 40 percent of alumina for all purposes. Enemy activities during the war seriously interfered with shipment of bauxite from the normal peacetime source in Surinam, Netherlands Guiana, South America, and focused attention on the necessity for increasing production from known domestic deposits. Even in peacetime, the production of aluminum ore in the United States could not satisfy requirements. Field drilling and exploration by Bureau of Mines engineers resulted in the discovery of important tonnages of high-grade bauxite suitable for treatment by the conventional Bayer process, Although an ore containing approximately 55 percent Al2O3 and only 2 to 4 percent SiO2 is preferable, it was necessary to use ores containing up to 8 or 10 percent SiO2. Because of the lower recoveries of aluminum with increased silica content, the Reconstruction Finance Corporation, through the Metals Reserve Company, established a base price of $4 for a 50-percent Al2O3 ore, containing 13-percent silica, with a premium or penalty of 14 cents for each percent of Al2O3 over or under 50; each percent of SiO2 under 13 was awarded a 20-cent premium, and each percent over 13 suffered a penalty of 43 cents; all prices were on the basis of 1 long ton of ore, dry basis.

Jan 1, 1949

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical assessment of orebodies in the mining industry typically relies on bench-scale or lab-based characterization techniques. In this study, we investigate drone- and tripod-based field hyperspectral imaging as a potential addition to the geometallurgy toolkit in multiple applications. This pilot study tests hyperspectral imaging for largescale mineral mapping in and around the active Lisbon Valley copper mine, including natural exposures, previously producing U-V mines, highwalls, dumps, and leaching sites. Tests include different (supervised and unsupervised) mineral data classification methods, varying mineral spectral reference libraries, comparison with ground-truth geological and spectroscopic mapping and sampling, and integration with LiDAR data. The results show that hyperspectral scans can produce spatially registered maps of the distribution of different spectrally active mineral types over dumps, highwalls, leach pads, and natural outcrops. Clays, other phyllosilicates, carbonates, and sulfates showed up particularly well. The sensor was also able to distinguish dry from lixiviant-saturated areas and map different clay types on the leach pads, and shows promise for differentiating types and health of vegetation. These results suggest that hyperspectral imaging, if coupled with robust ground-truthing, can be a useful complement to existing geometallurgical techniques in the mining industry, such as geological mapping, blast hole sampling and automated mineralogy identifications, and handheld spectrometry. In particular, hyperspectral imaging has promise for mapping the distribution of acid-consuming minerals; mapping the distribution of swelling, sliming, and heap-blinding clays; and pinpointing problem areas on heap leach pad surfaces.

Feb 10, 2021

By C Boyle

Brockman 2 mine is located in the Pilbara of Western Australia and is operated by Rio Tinto Iron Ore. Mineralisation is hosted by synclines where there is structural complexity to focus fluid flow. Mineralisation is hosted by the Brockman Iron Formation. Mining is on 10 m benches and blastholes spaced at 6 - 8 m apart are geologically logged, sampled by shovel cuts, and assayed using X-ray fluorescence for ten chemical variables. Blast blocks are digitised by mine geologists to assign destinations of material within blasts. Resource evaluation drilling is on a spacing of 50 m × 50 m across known mineralisation and consists of recent reverse circulation drilling and older open hole percussion drilling. Sampling of resource evaluation drilling is by rotary splitters or riffle splitters, and assaying is by X-ray fluorescence for ten chemical variables. Ordinary kriging of resource evaluation produces a long-term resource model. This study examines whether mine planning would be improved by using a blasthole estimate to extrapolate grades into deeper benches and merging the blasthole estimate with the long-term model made using resource evaluation drilling. The two estimates are merged into one model using an inverse weighting based on kriging variance. However, reconciliation results in a test bench show the original estimate made using resource evaluation drilling more closely matches mine geology block outs than does the merged model. This is due to a local trend of more high grade and higher iron grades of high grade in the area. The blasthole estimate of deeper benches must use extrapolation and it is diffi cult to take local trends into account. In contrast, the estimation using resource evaluation drilling is mainly interpolation and is better able to handle local trends.

Jul 11, 2011

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2018

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2017

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016

By L. Zhou, A. Martikainen, G. Goodman

Continuous airflow monitoring can improve the safety of the underground work force by ensuring the uninterrupted and controlled distribution of mine ventilation to all working areas. Air velocity measurements vary significantly and can change rapidly depending on the exact measurement location and, in particular, due to the presence of obstructions in the air stream. Air velocity must be measured at locations away from obstructions to avoid the vortices and eddies that can produce inaccurate readings. Further, an uninterrupted measurement path cannot always be guaranteed when using continuous airflow monitors due to the presence of nearby equipment, personnel, roof falls and rib rolls. Effective use of these devices requires selection of a minimum distance from an obstacle, such that an air velocity measurement can be made but not affected by the presence of that obstacle. This paper investigates the impacts of an obstruction on the behavior of downstream airflow using a numerical CFD model calibrated with experimental test results from underground testing. Factors including entry size, obstruction size and the inlet or incident velocity are examined for their effects on the distributions of airflow around an obstruction. A relationship is developed between the minimum measurement distance and the hydraulic diameters of the entry and the obstruction. A final analysis considers the impacts of continuous monitor location on the accuracy of velocity measurements and on the application of minimum measurement distance guidelines.

Jan 1, 2012