Search Documents

THOSE NOT MARKED ARE MEMBERS; MARKED THUS ? ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR ASSOCIATES ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. ?AARONSON, ALFRED E Pres., Tuloma Oil Co., Unity Bldg., Tulsa, Okla. '18 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co. 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, LOUIS BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div. Jenkins, Ky. 115 ABBOTT, ROBERT R. Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Fujitagumi Taiwan Office, Taipeh Formosa, Japan. '14 ABEEL, GEORGE H., JR., Cons. Min. Engr., 4111 Lafayette Ave., St. Louis, Mo. '18 ABEY, HIROSHI, Min. & Met. Engr., Arakawa Mine, Mitsubishi Co., Senpoku-gun, Akitaken, Japan. '17 ||ABOUCHAR, S. S., Cia. de Minerales y Metales, S. A. Santa Eulalia Unit, Apt. 70, Chihuahua, Chih., Mexico. '17 ABRAHAMS, A. I 1391 Madison Ave., New York N. Y. '14 ?ACKER, E. O'C., Met., 128 East Washington Lane, Germatown Philadelphia, Pa. '86 ACKER, WILLIAM L., Diamond Drill Contractor... Mears Bldg., Scranton, Pa. '18 ?ACKERMAN, ERNEST R., Pres., Lawrence Portland Cement Co. Plainfield, anion Co.. N. J. '15

Jan 1, 1923

By Ward B

Central Colliery was developed to exploit large underground reserves in the German Creek lease. It was planned from the outset as a retreating longwall operation and is the first longwall mine in Queensland. Longwall mining is not new to Australia but all previous experience has been confined to the coalfields of New South Wales. There was no precedent for longwall extraction in the markedly different geological setting of the Bowen Basin in Central Queensland. Various investigations were thus carried out during the initial development of Central Colliery, prior to the installation of the longwall, to ascertain the geotechnical characteristics of the coal seam and the adjacent strata and to predict the performance of the heading and pillar design as mining proceeds to depth. Laboratory tests showed the coal to be weak with an unconfined compressive strength of 9.6 MN/m2. Site inspection and geophysical correlation revealed a shear zone and extensive intraformational shear planes in the seam. The latter were found to exert a controlling influence on rib reaction in the headings. This behaviour was predicted by finite element modelling of the development headings which indicated that mining induced stresses in the coal would be relieved by block movement of the ribs. A chain pillar width versus depth curve was established for yielding pillar design based on empirical and computational methods. This gave pillar widths from 25m to 48m over the proposed depth range of 150m to 300m. Finite element modelling of the 25m pillars chosen for the first gateroads confirmed the overall stability of the design but suggested that rib spall could be significant in the adjacent tailgate. (1) Chief Mining Engineer, Capricorn Coal Management Pty. Ltd., German Creek Mine, Queensland (2) Senior Engineering Geologist, Coal Division, The Shell Company of Australia Limited, Melbourne

Jan 1, 1986

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By Scott W. Hazen

This report describes the design, analysis, and results of a special experimental mine-sampling project conducted as part of the Bureau of Mines continuing program on sample-methods research. The experimental project was conducted at the Bureau?s Denver Mining Research Center and at the Climax molybdenum mine within the framework of a cooperative research agreement between the Bureau and Climax Molybdenum Co., Division of American Metals-Climax, Inc. The primary objective of the project was to investigate the interrelation-ship between sample volume, number of samples, the standard deviation of an assay distribution, and the precision required for an estimate of grade of ore, and to develop this interrelationship into a relatively simple method of application for use in mine sampling.

Jan 1, 1962

By A. Lopez-Valdivieso

Particle size enlargement processes play an important role in solid/liquid separation, and in beneficiation unit operations. In the latter, not only the size of the formed aggregates but also their surface properties are very important. Oil agglomeration has a special place among such processes: it is a selective process in which hydrophobic particles are agglomerated into hydrophobic agglomerates which can be recovered by flotation. This explains the broad applications of oil-assisted beneficiation processes not only in the beneficiation of fine coal, but also in agglomerate flotation of many different types of ores, and in coal/gold agglomeration.

Jan 1, 2004

By Roy A. Grancher

HAPPY BIRTHDAY Not only is 1971 the Centennial Year of the AIME, but it also marks the One Hundredth Anniversary of the United States Portland Cement Industry. On September 26th in 1871 David O. Saylor of Allentown, Pennsylvania, received his patent Numbered 119,413 for the manufacture of portland cement. "Cement" had been used in the United States before that. This was, however, natural cement - a direct product of rocks as found in nature, usually burned at low temperatures in open kilns. During the early 1800s this natural cement played an important role in such projects as the building of the Erie Canal. It was only after the Civil War that small amounts of high priced portland cement was imported from Europe. The successful use of this material in construction led to Saylor's experiments and subsequent patent for the manufacture of a scientifically controlled product in this country. These one hundred years have witnessed four major "ages" of cement . . . three of them occurring in the last quarter century since World War Two. The first age was the "Age of Development", a seventy-year period which saw the growth of cement and its concrete end uses as major construction materials. Next followed a period called the "Age of Demand" when, after the war, cement became in short supply relative to large building requirements. In effect a cement shortage existed. The decade of the Sixties proved to be the "Age of Reaction", with its courses of action coming in response to the problems that arose when the industry's expansion programs provided too much capacity. Today cement, and the concrete industries, find themselves entering the "Age of Reason". Overcapacity, low price, rising costs, and poor returns are several of the reasons behind that name, As these industries face the construction challenge of the Seventies, and beyond, the application of basic management principles (otherwise known

Jan 1, 1971

By William H. Lewis

This paper describes the Bureau of Mines efforts in the research and development of a new and innovative mine lighting system which is based on fiber optics technology. The new lighting concept offers significant advantages over conventional systems in the areas of both safety and long- term maintenance costs. An overview of Bureau research into the problems and limitations of present-day mine lighting systems is also presented.

By R. T. Johansen, R. J. Heemstra

In water flooding the gradual accumulation of insoluble materials on the sand face causes the injection pressures to increase while decreasing the amount of water injected . This plugging material often is composed primarily of insoluble precipitates of calcium , iron , and magnesium . Treatment with sodium tripolyphosphate ( STP ) either eliminates or reduces the formation of precipitates . Field tests are discussed showing the almost immediate effects of using STP in the injection water . Methods of treatment , solubility of STP in fresh water and brines , and precautions to observe when starting to treat a waterflood with this chemical are given . Laboratory data show that the preferential wettability of a crude oil for reservoir rock can be reversed by adding a small amount of STP to the flooding water . This reversal in wetting tendency should not only decrease the injection pressures but also increase oil recovery by improving the sweep efficiency of a water flood .

Jan 1, 1964

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo, Noelia Munoz-Garcia, Michèle Heitz

Sulfide tailings from past and present mining activities are important hosts of critical elements and precious metals. This review paper presented a literature survey on the recovery practices of some critical minerals containing Te from sulfide tailings with a special focus on the physical beneficiation and hydrometallurgical separation methods. Finally, a conceptual framework and possible processing flowsheets were proposed. The findings of this review will be useful for the researchers in the field of geochemistry, mineral processing, and metallurgy to evaluate the separation processes for reprocessing of mine tailings for the recovery of critical minerals.

Feb 1, 2024

NEARLY all problems in mining engineering involve the transport and distribution of materials from place to place, and in general the most economically managed mines and plants are those in which the transport of materials has been carried out most efficiently. Of all these transport problems, the hoisting of ore out of the mine and the distribution of same to the various treatment works is perhaps one of the most important. It is proposed in the present paper to traverse the conditions,affecting the location, scale of operations, and design of the main shaft and head gear at the Mount Morgan mine; afterwards describing the designs and workings of the shaft house, winding engine, and transport from the shaft house to the treatment works.LOCATIONWhen the copper-gold ore was developed sufficiently to determine approximately the boundaries of the ore-body, it was found that the existing vertical shafts would be wholly inadequate to deal with the increased quantity of ore required to be handled. It was proposed, therefore, to construct a new shaft, and to handle in this...

Jan 1, 1911

By W. R. Crane

DRAINAGE in these mines has been discussed in papers, on mining practice,1 but the fact that water, varying from 0.16 to 3.46 and averaging 1.43 times the amount of ore mined, has to be pumped from the mines daily, indicates the importance of the problem and the advisability of making a thorough investigation of the source of mine water, its mode of entry into the mines, its effect upon mining conditions; and consideration of means of improving the conditions. While conditions are not serious, yet there is danger that they may become worse if present mining practice is continued, owing to the presence of formations, known to carry large quantities of water, that overlie the ore bed worked. Much detailed information has been collected regarding: rainfall, and run-off in streams draining the district; the effect of different kinds of formations, porous and non-porous; the inclination of the surface; the condition of the surface above the mines, i. e., whether or not disturbed by ground movement; the occurrence of the ore and character of associated formations, particularly with respect to presence of jointing or slip planes, faults, etc.; failure of top rock in the old stopes; and the conditions under which water effects entrance into the mines, i. e., whether as a natural or forced flow. The study furnished fundamental data on the source of waters now entering the mines and that which may later enter due to collapse of top formations in. abandoned workings. The presence of jointing, or slip planes, has a pronounced influence upon the whole drainage problem. These present lines of least resistance to the water and, by weakening the top formations, cause fracturing of the overlying rock, allowing both surface and deep-seated waters to enter the mines.

Jan 1, 1927

By Ulf B. Andersson, Christina Dahnér-Lindkvist, Bruno Figueiredo, Jessa Vatcher, Jonny Sjöberg, Joel Andersson

Hydraulic fracturing to precondition the rock mass in high seismic risk environments has great potential. Unfortunately, there are many unanswered questions about how to best implement a hydraulic fracturing program at individual mine sites, and even how to best use our engineering tools to evaluate these plans. To give the hydraulic fracturing field tests at LKAB’s Kiirunavaara Mine the best chance of success, fully-coupled, discontinuum numerical modelling Itasca’s 3DEC code was used together with statistical simulations of the fracture network. For modelling purposes, it was assumed that hydraulic fracturing successfully reduces seismic risk through 1) the creation of hydraulic fractures along a plane at each injection site, and 2) activation of existing discontinuities. A variety of scenarios for the mine were evaluated, which focused on site specific uncertainties (such as the spacing of the pre-existing discontinuities) and practical solutions (such as the hydraulic fracture spacing, selection of injection medium, and hydraulic fracture site location relative to production). The discrete fracture network (DFN) realizations were developed using available statistical data for discontinuities near where hydraulic fracturing was planned.

Apr 26, 2022

By Satayev IS, Shepelev DV

Various ways for applying the X-ray fluorescent method to process lump-by lump separation of secondary aluminium raw materials (scrap, slags, waste) as well as ferrosilicon and ferrochromium are being considered and physically demonstrated. A commercial X-ray radiometric sorter has been developed for processing secondary raw materials. Marketable quantities of aluminium scrap with appropriate copper and zinc content have been produced for smelting with a minimal additional of pure aluminium. An industrial complex for scrap processing, incorporating two X-ray radiometric sorters from the Hammermils company is successfully operating at one of the works in Russia.

Jan 1, 1993

By Qingxia Liu, Mingbo Zhang, Hongbo Zeng

The shortage of freshwater has been a major challenge for mineral flotation in arid areas. When using high salinity water, certain electrolytes are detrimental to flotation while others can improve the flotability of minerals. In this paper, the flotation behaviors and contact angles of pyrite in both Milli-Q water and high salinity water were investigated using different collectors at various pH levels. Results show that the thionocarbamate has a less affinity to pyrite in different solutions under mildly alkaline conditions as compared with potassium amyl xanthate (PAX) and N-isopropoxypropyl-N’-ethoxycarbonyl thiourea (iPOPECTU). At high pH levels, the slime coating on pyrite surfaces, which is caused by colloidal precipitates of magnesium and calcium ions in seawater, was confirmed by SEM, EDX and in-situ zeta potential measurement. The slime coating of colloidal precipitates on mineral surfaces led to low recovery of pyrite at high pH levels. The study of flotation behavior of pyrite in high salinity water improves our fundamental understanding of mineral flotation in seawater.

Jan 1, 2015

By M. Prasad

Growing concern over increased levels of atmospheric carbon dioxide has prompted new interests in development of materials and techniques for its sequestration. Various research and developmental work on different aspects of carbon capture technology are being extensively carried out worldwide. The main objective of the present work is to synthesize a HAS material having high capacity and robust ability for recycling to capture greenhouse gases with special reference to carbon dioxide (CO2) from the sources from where it is released to the atmosphere. Existing CO2 capture techniques involves the use of solid materials that lack sufficient stability for repeated use or liquid adsorbents that are expensive and require significant amounts of energy. Keywords: greenhouse gases, carbon capture, solid adsorbent, HAS material

Sep 1, 2012

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle and Safety Guidelines developed under U.S. Bureau of Mines Contract No. JO 366003, ?Improving Man Transit Safety. This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements are embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle Is presented In Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By Luisa Alfieri, Giorgio Fantauzzi, Sergio Notarianni, Spencer Cavagnet, Alessandro Damiani

"The new tunnels of the Copenhagen ""Cityringen"" will be excavated, at Kongens Nytorv square, crossing over the existing M1 and M2 metro lines. After the crossing, the tunnels will underpass the historical building of the Magasin du Nord and adjacent masonry buildings, with a minimum tunnel cover of about 4.5 m. The tunnels have an internal diameter of 4.9m and are being excavated through earth pressure balanced Tunnel Boring Machines in mixed face.The Magasin du Nord estate is characterized by a very complex structure, with different blocks built in different times. An assessment of the condition of the building and its sensitivity to tunnellinginduced ground movements has been conducted through a fully coupled soil-structure interaction analysis; based on the results of this analysis, mitigation measures have been designed.INTRODUCTIONThe Copenhagen Metro Cityringen is expected to be running in July 2019 and will consist of two single tracks in a twin tunnels, each approximately 16 km in length, for transporting up to 243,000 passengers on an average work day. The Cityringen includes 17 underground stations with island platforms, 4 crossover facilities and 3 construction and ventilation shafts. The tunnels is being excavated using earth pressure balanced Tunnel Boring Machines and have an internal diameter of 4.90 m.The intersection with the existing M1 and M2 metro-line will take place at Kongens Nytorv and at Frederiksberg. According to the design alignment, in Kongens Nytorv the new tunnels will pass over the existing M1 and M2 ones; as a result of this, the tunnels will underpass the historical building of the Magasin du Nord and the adjacent masonry building hosting a Mc Donald’s with a minimum cover of about 4.5m.In the framework of Risk Assessment for sensitive buildings, the effects of tunneling-induced ground movements on the Estates ØS0437 (McDonald’s building), ØS0428 (Magasin du Nord) and ØS0004 (Hviids Vinstue) were evaluated. To achieve this goal a fully coupled soil-structure interaction has been considered and the entire excavation process has been reproduced in a 3D model where the abovementioned buildings have been modeled. In this way, a risk assessment analysis was performed evaluating directly the effects of the excavation in terms of settlements and variations of the internal forces as far as the excavation process proceeds. In figure 1, a picture of the construction of Kongens Nytorv station, with Magasin du Nord and Mc Donald’s building on the background, is presented."

Jan 1, 2016

By R. C. Corey

Anticipating the need for convenient, economical, and safe means for disposing of combustible wastes contaminated with low-level activity, in connection with private and institutional uses of radioisotopes, the Atomic Energy Commission (AEC) has provided the Bureau of Mines with funds to develop an incinerator for this purpose. A prototype incinerator, designated hereafter as BOMAEC-30, was designed, constructed, and tested, based on fundamental and applied research investigations of the combustion characteristics of rubbish and sawdust, which will comprise the bulk of contaminated wastes. No radioisotopes were used in the tests; the objective was to remove as much particulate matter from the products of combustion as possible. The prototype unit was designed to burn 30 pounds per hour, using 100 percent over fire air admitted tangentially in an all-metal, cylindrical combustion chamber. The gas-cleaning system consisted of special fabric bags and absolute filters.

Jan 1, 1962

By E. Watkins, S. J. SCHATZEL, K M. AJAYI, V. Gangrade, Z. Khademian

A stochastic discrete fracture network (DFN) model is developed based on mine site core log data to predict the horizontal and vertical permeabilities from the surface to the top of the caved zone at a longwall mining site in southwestern Pennsylvania. One hundred DFN realizations were generated to determine permeabilities for the isolated zone over an abutment pillar after mining the second panel. The results from this study show that the vertical and horizontal permeabilities from the DFN model agree closely with field measurements, which indicates that the resultant permeability obtained from the field measurements is representative of the predicted permeabilities. With this agreement, the aperture data for other zones of the mine could be obtained from the geomechanical model — specifically, for the fractured zone over the gob. Based on the successful validation of this model, this model could be further developed to predict the permeability of the fractured zone over the gob with fracture aperture obtained from the geomechanical analysis. This will complete the fracture characterization of the overburden, which could be used to predict potential shale gas flow to the mine in the event of a breach. This prediction could provide information on the associated risk of a casing breach and determination of methods to proactively prevent such an occurrence.

Feb 1, 2023

By A. E. M. Warner, A. Vahed, P. J. Mackey

"Since early 2015, the price of nickel has dropped from the region of US$6/pound to current levels of around US$4.60/pound (March 2017), reflecting several market factors, but principally due to lower demand from China. Under such conditions, nickel companies have been under pressure to contain operating costs. In addition, labor and energy costs will continue to rise, while nickel ore grades will likely continue to drop. All major companies now accept the need for climate change action and consequently efforts are being made towards lowering carbon-based emissions. Nevertheless, meeting these challenges can also contribute to higher operating costs without parallel innovative developments - which at the same time, under current conditions, major companies are tending to curtail. In this paper, several productivity improvement opportunities to reduce unit operating costs at nickel sulphide and nickel laterite plants are reviewed. Opportunities include: (a) process technology and energy-type selection, production capability, optimization of process intensity and implementation of newer technologies; (b) improved productivity, equipment availability including maintenance best practice; (c) energy savings and recovery opportunities and use of energy surveys and, (d) process modeling and improved scheduling. Such improvements along with an uptick seen in nickel demand going forward should better position the world nickel industry.INTRODUCTION Nickel is an essential metal to modern society, primarily through its use as an important ingredient in stainless steel. Thus, stainless steel finds vital applications in food preparation facilities, as well as important uses in transportation and industrial applications. Canada has always played an important role in nickel production and nickel metallurgy. In the 1940s and 1950s, Canada supplied over 90% of the world’s nickel. However, this proportion has declined considerably to around 10% of the world nickel supply today. Still, Canada remains an important nickel supplier and contributor to nickel extractive technology. Due to the importance of nickel to society, nickel demand is expected to continually rise. On the other hand, nickel companies have been under pressure to contain production costs amid languishing nickel prices. While demand projections show nickel growth, there are uncertainties in actual levels of future market growth. Ore grades are dropping, while labour and energy costs, which are key cost contributors are rising, hence efforts to lower production costs will generally require innovative approaches."

Jan 1, 2017