Search Documents

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By T. F. Witherbee

IT is proposed to give, first, a description of the works ; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

Jan 1, 1876

By Richard A. Allwes

The Bureau of Mines conducted an in-mine case study on two consecutive three-entry gate road systems designed in accordance with the stiff-yield pillar design concept. This Bureau study was conducted in order to further develop technology that will improve the health and safety aspects of longwall mining. Support loading and strata activity were monitored to determine the effects of retreat longwall mining on the gate road ground control system. Analyses of pillar stress and roof bolt loading histories revealed that headgate roof support elements ex-perienced cumulative loading throughout the life of the longwall panel. Tailgate pillar loadings had significantly different histories from the loading histories of the headgate pillars. Stress relief occurred in the tailgate pillars following the passage of the longwall face. More-over, the stiff-yield pillar design, with the abutment pillar placed adjacent to the working panel when part of the headgate system, provided effective ground control in that no major roof falls or roof problems were experienced in the headgate or tailgate systems during longwall mining.

Jan 1, 1985

By David D. Walker

The purpose of the investigation was to describe and appraise tungsten deposits in Montana . The work supplements previous investigations made by Pattee ( 10 ) and Walker ( 17 ) in selected areas of the State . Scheelite deposits in tactite are the most numerous and most important economically , having accounted for nearly all of the State's tungsten production . Of the 64 deposits examined during the current study , 50 contained scheelite , 11 hubnerite , 2 wolframite , and 1 ferberite . The State's major tungsten production has been from scheelite deposits in Beaverhead County . The report lists , by counties , the type and grade of each deposit . The more important occurrences are accompanied by geological and assay maps .

Jan 1, 1963

By H. Jiang, Y. Luo

The study develops an automated, high-efficiency drilling control system to reduce respirable dust and increase energy efficiency in underground coal mines. It uses specific energy to evaluate efficiency and proposes a comprehensive drilling control algorithm based on laboratory tests. The algorithm optimizes drilling parameters to maintain high efficiency, reduce dust generation, and improve safety.

Feb 12, 2022

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By James Corcoran, Richard McLane, Matt Neuner, Joseph DeMello, Hugh Davies

The Los Angeles County Metropolitan Transportation Authority (LA Metro) Purple Line Extension Section 1 (PLE1) is a $3.12 billion USD design-build, underground heavy rail project, connecting an existing station at Wilshire Blvd. and Western Ave. and extending 3.92 miles under Wilshire Blvd, terminating approximately 550 feet west of Wilshire and La Cienega Blvds. The project alignment runs immediately adjacent to the La Brea Tar Pits, world renowned for Pleistocene fossils and continuous seepage of asphaltum (locally known as tar) and gas in an urban setting. This paper presents a successful case history of the planning, design, and construction efforts to safely construct the bored tunnels through Reach 3 of the alignment (between Wilshire/Fairfax Station, and Wilshire/La Cienega Station), in a designated Methane Zone in the City of Los Angeles. Historical context on decades of challenges and studies is summarized. Further, this paper outlines the pro-active partnership between the Owner: LA Metro, the Design Builder: Skanska-Traylor-Shea Joint Venture, and geotechnical design services provided by Golder Associates to safely manage pressurized face tunneling through a confined gas zone near the La Brea Tar Pits. Specifically, a program of in-situ oxidation and soil gas extraction was designed to test and analyze risks associated with pressurized face TBM tunneling through the complex subsurface geological conditions, then implemented during construction. In advance of tunneling, a network of wells was used to draw air into the gas zone to oxidize the 6,500 ppm hydrogen sulfide gas, as well as determine methane recharge rate. During TBM tunneling, the wells were converted to a gas extraction system to evacuate, filter (H2S) and burn (CH4) the gas as the Tunnel Boring Machine passed, providing a preferential pathway for the gas to migrate toward extraction wells, and preventing the migration to adjacent buildings. The team extracted and treated 3,857,000 cubic feet of mostly methane gas over 40 days as the TBMs passed through the zone. Gas behavior, pressures, and concentrations were monitored not only from the extraction system, but also in basements and utility vaults along this section of the alignment.

Jun 13, 2023

By T. J. De Mull

The Alligator Ridge Mine is located 70 miles northwest of Ely in White Pine County, Nevada. Development of the mine began in the late 1970's as a joint venture between Amselco Minerals, Inc. and Occidental Minerals Corporation, with Amselco as the operating partner. Early in 1983 Nerco Minerals Company acquired Occidental's share of the property. The mine and ore processing facility have operated at capacity since 1981 producing 680,000 tonnes of ore and 1,900 kg of gold per year. The gold ore deposits at Alligator Ridge consist of disseminated micron-size gold particles in a silicified siltstone matrix. The deposit comprises three separate but adjacent areas of mineralization that are designated as Vantage 1, Vantage 2, and Vantage 3 after the name of the basin in which the deposits lie.

Jan 1, 1983

The blasting process involves a complex interaction of a delayed sequence of moving sources of seismic energy which produce nonlinear behaviour near the blast holes. A deterministic description of this nonlinear behaviour represents a formidable problem. The modelling of blast vibrations remote from the blast source may use some of the primary features of the blast design such as charge type, charge weight and initiation sequence. Such modelling of blast vibrations usually assumes linear behaviour remote from the blast holes. Site specific charge weight scaling laws may be used to predict the blast vibration levels with relatively poor accuracy. An important ingredient which is missing from charge weight scaling laws is the seismic source wavelet emanating from each blast hole. The present paper considers some approaches which may be used to determine a suitable source wavelet. The wavelets are suitable for use in the region where linearity may be assumed. In that region, it is possible to model the attenuation and scattering of the seismic wave as it propagates from the blast source to the measurement location.

Jan 1, 1990

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

By Albert L. Toenges

EARLY in 1949, the Economic Cooperation Administration requested the Bureau of Mines to assign a coal-mining engineer to study milling conditions in Greek lignite mines; to make recommendations for the introduction of methods and practices that should increase production and decrease the cost of mining; and, from the results of a geological reconnaissance by geologists of the United States Geological Survey, to suggest plans for the development of mines to supply fuel for a thermal power plant, Albert L. Toenges was assigned to this investigation and arrived in Athens, Greece, March 15, 1949. The study of mining operations and the geological reconnaissance (which was made by W. G. Pierce and X. M. Denson, geologists, United States Geological Survey) Were conducted concurrently. The Geological Survey will publish the results of its investigation separately. Washability studies of lignites from Aliveri and Kimi were made at the Central Experiment Station of the Bureau of -Mines, Pittsburgh, Pa. The lignite fields mentioned in this bulletin are shown in figure 1.

Jan 1, 1951

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be rehandled. Prior studies have shown that by only changing blasthole timing with the same blast design, fragmentation and throw alter. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum interhole delay for fragmentation has been found by studying timings from 0 millisecond (ms) to 45 ms. Instantaneous timing between holes increased the throw by more than 31 m (100 ft), but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw.Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.”Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is rehandled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators have allowed for precise delay timings to be used between rows, holes and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation."

Jan 6, 2017

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By Donald J. Keefe

The Remote Working Level Monitor (RWLM) is an instrument used to remotely monitor the Rn-daughter concentrations and the Working Level (WL). It is an ac powered, microprocessor based instrument which multiplexes two independent detector units to a single central processor unit (CPU). The CPU controls the actuation of the detector units and processes and outputs the data received from these remote detector units. The remote detector units are fully automated and require no manual operation once they are set up. They detect and separate the alpha emitters of RaA and RaC' as well as detecting the beta emitters of RaB and RaC. The resultant pulses from these detected radioisotope; are transmitted to the CPU for processing. The programmed microprocessor performs the mathematical manipulations necessary to output accurate Rn-daughter concentrations and the WL. A special subroutine within the program enables the RWLM to run and output a calibration procedure on command. The data resulting from this request can then be processed in a separate program on most computers capable of BASIC programming. The calibration program results in the derivation of coefficients and beta efficiencies which provides calibrated coefficients and beta efficiencies.

Jan 1, 1977

By T. F. Witherbee

It is proposed to give, first, a description of the works; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

By Y Xu, T Rowles, B Dareeju, A Dissanayake

Recent updates on tailings dam design guidelines require analysis of undrained (short-term) stability with the application of the SHANSEP model. The SHANSEP model, which was originally developed for alluvial soils, predicates that the Undrained Shear Strength (Su) increases with increasing effective stress. Residual soils by their nature do not necessarily follow this relationship. This paper examines an alternate method to define Su over a range of effective stress conditions for residual soils. Residual soils, formed by weathering of their parent rocks, are generally micro-structured in nature. The microstructural features, such as interparticle bonding, play a fundamental role in stress-strain behaviour of the residual soils. As interparticle bonding is independent of effective stress and void ratio, the undrained shear strength of residual soils is expected to be less dependent on effective stress than alluvial soils, especially at low stress levels. A series of triaxial tests conducted on residual soils, however, indicated that the undrained shear strength and the undrained shear strength ratio (Su/σv’) are to a degree dependant on effective stress. It was found that the undrained shear strength ratio is significantly higher under low stress levels and progressively reduces with increasing effective stress. Based on the laboratory testing data, a strength function with varying undrained shear strength ratios can be developed for the residual soils under the stress range anticipated for a design of a tailings dam. This includes capping the input undrained strength at lower effective stresses based on the drained (effective) and minimum undrained strength. The Factor of Safety (FOS) calculated for the embankment utilising the traditional limit equilibrium (LE) method indicated the application of undrained strength function for the residual soils can provide a significant optimisation for the embankment design compared to adopting a constant undrained shear strength ratio or constant undrained shear strength in the design.

Jul 1, 2021

By Charles B. Manula

This paper describes the development of a mathematical model for simulating the behavior of a longwall coal production system. The longwall simulator is a design simulator incorporating both deterministic and stochastic methods to calculate: (a) the size and density of support; (b) the cutting force, power requirements and haulage speed for the loader-shearer; (c) the conveyor size, speed and power requirements; and (d) delay generation at head and tail-gates and the longwall face.

Jan 1, 1978

Kroemer(1-3) and Kroemer et al.(4) define the isoinertial technique of strength assessment as one in which mass properties of an object are held constant, as in lifting a given weight over a predetermined distance. Several strength assessment procedures possess this characteristic. Most commonly associated with the term is a specific test developed to provide a relatively quick assessment of a subject's maximal lifting capacity using a modified weight-lifting device.(1,5) The classic psychophysical methodology of assessing maximum acceptable weights of lift is also considered an isoinertial technique under this definition.(6) While the definition provided by Kroemer(1) and Kroemer et al.(4) has been most widely accepted in the literature, some have applied the term "isoinertial" to techniques that differ somewhat from the preceding definition, such as in a description of the Isotechnologies B-200 strength testing device.(7) Rather than lifting a constant mass the B-200 applies a constant force against which the subject performs an exertion. The isoinertial tests described here apply to situations in which the mass to be moved by a musculoskeletal effort is set to a constant. Is Isoinertial Testing Psychophysical or Is Psychophysical Testing Isoinertial? As various types of strength tests have evolved over the past few decades, some unfortunate developments in terminology have arisen to describe and classify different strength assessment procedures. This is particularly evident in sorting out various tests that have been labeled "isoinertial." One example was cited earlier. Another problem that has evolved is that the term "isoinertial strength" has two connotations. The first is the conceptual definition: isoinertial strength tests include any strength test in which a constant mass is handled. In practice, however, the term is often used to denote a specific strength test in which subjects' maximal lifting capacity is determined using a machine and a constant mass is lifted.(1,5) Partially as a result of this dual connotation, the literature contains references to both "isoinertial strength test" as a psychophysical variant(8) and the psychophysical method as an "isoinertial strength test" (4,9) To lay the framework for the next two chapters, the authors will briefly discuss some operational definitions of tests of isoinertial and psychophysical strength. In stating that the isoinertial strength test is a variant of the psychophysical method, Ayoub and Mital(8) refer to the specific strength test developed by Kroemer(1) and McDaniel et al.(5) Clearly, this isoinertial protocol has many similarities to the psychophysical method: both are dynamic; weight is adjusted in both; and both measure the load a subject is willing to endure under specified circumstances. However, while both deal with lifting and adjusting loads, there are significant differences between the psychophysical (isoinertial) technique and the Kroemer-McDaniel (isoinertial) protocol in their procedures and the use of the data collected in these tests. For our purposes, we designate the

Jan 1, 1998

By N. L. Wimmler

The chromite deposits along the Stillwater complex in Stillwater and Sweetgrass Counties, Mont., have at various times been studied and reported on by the Federal Geological Survey, the Montana Bureau of Mines and Geology, other Government agencies, and private interests, Several of the deposits were explored to a mall extent by the owners during the World War of 1914-17, but no production resulted. The importance of these deposits and the urgent necessity of developing large domestic sources of chromite were realized shortly before the beginning of the recent World War. These deposits were therefore investigated and developed by Government agencies and., as a result, now afford the largest known reserves of chromium in the United States. In 1939, under the authority of the Strategic Minerals Act, the Bureau of Mines and the Geological Survey made preliminary investigations of these deposits. As a result, the Bureau of Mines conducted an extensive program of trenching, diamond core drilling, and sampling. This work was begun in August 1939 and continued to April 1943. The Bureau of Mines also performed numerous metallurgical tests on the beneficiation of the chromite ores and concentrates and for the production of chromium metal there from. Research continues as a means toward utilizing these ores.

Jan 1, 1948