Search Documents

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heating at 200°C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. Materials and Methods The work was done on high grade electrolytic copper, 99.942 per cent. copper plus silver, silver 0.0008 per cent. It was hot-rolled to >/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire 'were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, L. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite by an acid pressure leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project.

Jan 1, 2004

By Kirkhouse C. B

Soon after the Broken Hill Limited started operations at their Iron and Steel Works at Newcastle, NSW, it was found necessary to install a mill for rolling small merchant bars, rounds, etc.An arrangement of the first mill laid down is shown on Plate 1., Fig. 1. This mill commenced operations on the 18th July, 1917.The feed for this mill was rolled in the existing 18-in. mill and sheared to the lengths required before being delivered to the billet storage yard. The billet storage yard is 90 ft. span, and is served by one 10-ton electric overhead travelling crane. Billets were placed on the billet bed preparatory to being charged into the heating furnace.The heating furnace was of the continuous recuperative with end discharge and had a hearth 40 ft. long by 10 ft. wide. The billets were pushed through the furnace by means of two hydraulic rams, which could either act together and push one row of billets, or act singly and push two rows of billets. This furnace was fired by producer gas from the producers shown on Plate I., Fig. l.The gas was conveyed to the furnace by means of a brick underground flue.

Jan 1, 1935

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By Philip Bucky

THE term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater mecha-nization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar model built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimensions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein.

Jan 1, 1938

By C. Dorfling, M. Tadie, M. Tucker

Electrowinning is the final step in the hydrometallurgical production of high purity copper, involving the passage of electric current through an electrolyte and consequent plating of solid copper to form cathode sheets. Key electrowinning performance indicators are the current efficiency, specific energy consumption, yield, and quality of the metal. The high energy demand and associated cost mean that determination of performance indicators is critical during operation, but ‘online’ measurement is impractical due to the nature of the measurements and corrosive environment brought about by acid mist. This research considered the development of a predictive electrowinning model as a shift towards a pre-emptive approach to attaining plant performance data. A steady-state model was created from input variables available in the industry, using a first-principles approach combining mass balances, electrochemical and thermodynamic equations, and property correlations. A circuit diagram equivalent of an electrowinning cell, containing multiple pairs of electrodes, was used as the backbone of the model. The kinetics of each electrochemical reaction were modelled including iron as a major impurity. Losses in current efficiency due to ineffective electrode contact, short circuits, and stray currents were also incorporated. The model was used to predict the current efficiencies for tests performed at varying conditions in a bench-scale electrowinning cell; the average absolute error between the measured and predicted current efficiencies was 3.2%. The model requires a unique parameter fitting approach for each industrial operation; if parameters are customised for specific plants, the model will be a useful tool to predict performance and can aid the development of effective process control systems in copper electrowinning tank houses. Keywords: Copper; current efficiency; electrowinning; modelling; plating rate

Jan 1, 2020

By Edgar Bain

SUMMARY THE results of an enquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration 'are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research Laboratories. All the compositions studied contained carbon in amount comparable to commercial alloys.

Jan 3, 1927

By R. L. Cosgriff

A commercial, battery-powered mine vehicle has been equipped for remote operation in coal mines. This vehicle is controlled by an operator from the remote station. Command signals originating at the remote station as well as video and data signals originating on board the vehicle are relayed between the remote station and vehicle using a single coaxial line. This coaxial line is normally 2,000 feet in length and is reeled in and out from a drum mounted aboard the vehicle The vehicle has a maximum speed of 6 ft/sec and a minimum speed of 4 ft/sec using 36-volt excitation of the traction motor. If this traction motor is excited by two of the three batteries, 24-volt excitation, the vehicle will travel at approximately 2 ft/sec. The speed can be reduced by the operator to 1 ft/sec. This vehicular system has been tested in coal mines. Presently, the major limitation of this system is associated with fatigue failure of the splices in the coaxial line and lack of mobility caused by its 3-wheel design.

Jan 1, 1974

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

By Fábio Lerbach

Balanço Energético Global da Vallourec Sumitomo Soluções Tubulares do Brasil site Jeceaba em 2016, com os principais indicadores de consumo energético das áreas consumidoras. Além dos indicadores energéticos globais, o balanço apresenta os consumos específicos de cada insumo nas diversas áreas, permitindo a análise de cada setor da Usina, isoladamente. Destaca-se em 2016: - desligamento do AF em nov/2016

Jan 26, 2018

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By G. M. Ault, G. C. Deutsch

The paper reviews the efforts made to utilize powder metallurgy to solve problems encountered when using alloys at high temperatures. The following subjects are discussed: comparison of wrought and sintered super alloys, sintered aluminum powder, porous materials for transpiration cooling, molybdenum, and cermets. TODAY, powder-metallurgy techniques are be-JL coming increasingly important, producing materials which at the present time cannot be made by any other method. Among these materials are high melting-point metals such as tantalum and tungsten, porous metals for filters and lubricant-containing bearings, electrical contacts and electrodes (i.e., tungsten-copper), cutting tools of the cemented carbides, and magnet alloys. In addition, the powder-metallurgy industry has grown because, through the application of its methods, shaped parts, such as gears, can be produced at tremendous rates with a low scrap loss in comparison with manufacture by casting or forging and machining. In the past few years, by utilizing powder metallurgy, several approaches to the problem of high temperature materials have been investigated. In this paper the authors will review some of the studies on application of materials having properties above 1350°F. Since their experience lies in the aeronautical field, possible uses of powder-metallurgy techniques in the production of aircraft en- gines will be emphasized. A large portion of the work is classified, but such a restriction has not eliminated any field from discussion, although limiting the amount of detail it is possible to present. The development of high temperature alloys from powders and porous metals for cooling will be discussed as well as research done on molybdenum and molybdenum alloys, cermets, and intermetallics. Some studies on the utilization of cermets will be considered along with special problems that have been revealed through these investigations. Special interest in certain factors of sintered aluminum powder (SAP) makes it desirable to discuss this material although its use temperature is below the 1350°F limitation set for this paper. High Temperature Alloys from Powders In general, components made from powders for room-temperature application have been investigated with the primary purpose of taking advantage of the high production rates and economies made possible by powder metallurgy. From the standpoint of properties, the ojective of the powder metallurgist has been to obtain a product comparable to the cast or wrought product that is to be replaced. Comparisons of the properties of alloys made by powder-metallurgy methods with those of similar compositions made by casting and forging are reported in the literature.12 In many cases equivalent

Jan 1, 1955

By Jay F. Colinet

Respirable dust exposure has long been known to be a serious health threat to workers in many industries. In coal mining, overexposure to respirable coal mine dust can lead to coal workers? pneumoconiosis (CWP). CWP is a lung disease that can be disabling and fatal in its most severe form. In addition, miners can be exposed to high levels of respirable silica dust, which can cause silicosis, another disabling and/or fatal lung disease. Once contracted, there is no cure for CWP or silicosis. The goal, therefore, is to limit worker exposure to respirable dust to prevent development of these diseases. The passage of the Federal Coal Mine Health and Safety Act of 1969 established respirable dust exposure limits, dust sampling requirements for inspectors and mine operators, a voluntary x-ray surveillance program to identify CWP in underground coal miners, and a benefits program to provide compensation to affected workers and their families. The tremen­dous human and financial costs resulting from CWP and silicosis in the U.S. underground coal mine workforce are shown by the following statistics: ? During 1970?2004, CWP was a direct or contributing cause of 69,377 deaths of U.S. underground coal mine workers. ? During 1980?2005, over $39 billion in CWP benefits were paid to underground coal miners and their families. ? Recent x-ray surveillance data for 2000?2006 show an increase in CWP cases. Nearly 8% of examined underground coal miners with 25 or more years of experience were diagnosed with CWP. ? ?Continuous miner operator? is the most frequently listed occupation on death certificates that record silicosis as the cause of death.

Jan 1, 2010

By J. A. Abols, P. M. Grady

Recovery via gravity is one of the oldest mineral processing methods available. Unfortunately, the use of gravity techniques for gold recovery has been in decline for the past century as more effective chemical processes such as flotation and leach/CIP have been developed. Recently, with the push towards more sustainable environmental outcomes, the benefits of gravity separation have become more apparent. While gravity as a unit process is not usually capable of achieving as high a recovery as flotation or whole ore cyanidation, a combination of gravity devices alone or in conjunction with these processes can offer significant advantages to the operator. This paper reviews the range of gravity devices available, their application and the results that can be achieved by maximizing gravity through the use of a combination of gravity recovery devices. Three case studies are provided.

Jan 1, 2005

By G. M. Thain

Ancient Mining - The following three contributions were received for publication in addition to the preceding papers. 1. Ancient gold-mining sites in the Transvaal G. M. THAIN* Pre-European gold mining and working in South Africa is a tantalizing field for conjecture. Well over thousand sites have been identified in Rhodesia, but here we have had to reach double figures, judging by published accounts. Geologically, the Transvaal is less amenable primitive exploitation, but it difficult to reject the idea that the knowledge gained to the north did not have its influence south of the Limpopo.

Jan 1, 1974

By D. Harrington

"In order to stimulate general interest in mine safety among their employees the mining companies of Butte, Mont., instituted in 1918 a Miners' Field Day, and this field day has since been held annually about the end of July, the last one being on July 25, 1921. The mining companies of the Butte district finance this meet in proportion to the number of men employed at the time of the meet, the contributing companies with number of working force, end proportional contributions for the opening field day in 1918 being given below:COMPANY NUMBER EMPLOYED AMOUNT CONTRIBUTEDAnaconda Copper Mining Co.,12,500,$ 1,078.53Butte & Superior Mining Co.,1,800,155.32North Butte Mining Co.,,1,294,111.67East Butte Copper Co.,,850,73.36W. A. Clark Interests,,600,51.78Davis-Daly Mining Co.,,340,29.35,,,,17,384,$ 1,500.00*Note: In many mining districts it is now the custom to hold an annual Miners' Field Day. The field day, as a rule, is financed principally by the mine operators, and was instituted primarily to promote interest among miners in the ""Safety First"" movement. Usually demonstrations or contests in first aid and mine rescue are the leading feature of the day's events, which include games, races, dancing, and all the other amusements usual to a gala holiday. Thus the field (ley serves the double purpose of stimulating interest in mine safety and promoting cordial relations and community fellowship. This paper is an interesting account of the way in which the Miners' Field Day in the Butte district is organized, with data on costs, plan of organization, method of conducting, and the practical benefits derived from it. - Ed"

Oct 1, 1921

By N. H. Emmons

An interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at its plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory. Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaccs. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top mas necessary and the engineering force was started on the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of east copper, but the heat was great that the copper bent readily, due to the jarring of its

Jan 1, 1911

By Paul M. Tyler

One by one new metals come to share the burden of modern industry. Long before the Christian era potters and glass workers employed fine and costly blue pigments that contained cobalt. Cobalt blue class has been found in the tombs of the Egyptians and in the ruins of Troy, and many of the colors used by the ancient Greeks and Romans contained cobalt. The ancients, however, were apparently unaware that the colors they used were caused by cobalt, and it was not until late in the 17th century that the existence of the element was recognized, Writers in the Middle Ages referred to "cobalos" as an evil spirit that haunted mines and caused trouble to the miners. Subsequently the German worms "Kobold," meaning goblin, came to be applied to any baffling mineral and particularly to minerals that resembled ores but failed to yield metal when smelted. Even to-day there is something of an air of mystery about cobalt, and a medieval cloak of secrecy still surrounds many of the metallurgical processes employed in its production. "Zaffre" was mentioned about the middle of the sixteenth century by Biringuccio, and in 1735 the metal war, first prepared by G. Brandt. To preparation of cobalt compounds, however, must have been carried on in at least a small way ever since the opening of the silver-cobalt deposits of Schneeberg in 1470. By 1790 there were 25 works engaged in the industry, rust of them located in Saxony, but the total output of these works probably did not exceed 300 tone of cobalt annually, mostly in the fore of smalt. The smalt which contained approximately 6 per cent cobalt was sold in Venice in 1520 at about 16 cents a pound. A few refineries in Holland supplied the Irish linen trade, contributed a farce amount to the Dutch linen industries, and alto provided smaller quantities for the manufactuer of litmus in Holland. A complete description of the early [histor,] of the cobalt industry in Saxony, is given by Mickle in the Deport of the Bureau of Mines of Ontario, vol. 19, 1913, pt. 2, pp. 234-251.

Jan 1, 1930

By Christopher Newman, David Newman

The ability to assess, address, and predict mining-induced stress distribution is paramount in maintaining a safe and efficient underground operation as coal mines continue to develop at deeper depths and in more geologically complex reserves. This is especially true for longwall mining operations given their limited flexibility in panel layout and orientation. This paper focuses on ground behaviors and conditions observed at two deep-cover, steeply dipping longwall mining operations in Utah’s Unita coal basin. This region is susceptible to coal pillar bump/bounce events as a result of high depth of cover, high-extraction mining, and the close proximity of a thick massive stiff sandstone stratum to active mineworks. The successful prediction of mining-induced coal bump events for Mine A and Mine B operating in the Unita basin has prompted mine management to develop a rock mechanics testing database for reserve calculations. The database is applicable to mine planning as well as the development of multiple numerical models to proactively identify and address adverse ground conditions using input parameters calibrated to site-specific behaviors and conditions. For both Mine A and Mine B, the most critical question relates to longwall development and recovery for “extreme” deep-cover longwall panels at overburden depths greater than 600 m. This paper highlights the impact of high-stress concentrations associated with deep-cover longwall mining as well as the methods applied to mitigate stress impacts on miner safety and longwall production.

Jul 1, 2023