Search Documents

By Gordon Cook

American Electric Power Company (AEP operates 31 coal mines in three states, and some 26 electric generating stations (19 coal-fired) located in the Ohio River Basin. Normally the system burns over 36,071,600 tonnes (40,000,000 tons) of coal and generates in excess of 3.6 X 1018 J (100 billion kwh) of electricity per year. In 1975, AEP, in response to the progressively more stringent air quality requirements of the clean air act, acquired large low-sulfur reserves in Carbon County, Utah (Figure 1. Location Map). Price River Coal Company (PRCC) is the operator OF this multi-seam complex, which is part of the Book Cliffs coalfield at an elevation exceeding 1,829 m (6,000 ft.). The topography is mountainous and divided by numerous canyons. Flat areas are at a premium (Figure 2. Castle Gate Area). Modern high production longwall mining takes in some top and bottom waste, and in this particular operation, it amounts to about 14% of the ROM tonnage.

Jan 1, 1983

By Arthur C. McFarlan

There are two distinct coal fields in Kentucky-the Eastern field constituting a part of the Appalachian coal region and the Western field constituting the southern part of the Eastern Interior region. The outcrop pattern of the State is dominated by the Cincinnati arch. Coal-bearing Pennsylvanian strata occupy a low structural position on either flank, preserved thereby from erosion, which in the past has removed these same beds, though a much thinner succession, from the crest of the arch. General geological relationships are shown in figures 1 and 2. On April 13, 1750, Dr. Thomas Walker discovered the first coal recorded in Kentucky. He entered the State through Cumberland Gap (Cave Gap) and found coal a few miles north.

Jan 1, 1944

By Richard Crockford

The World Trade Center (WTC) is located on the west side of Manhattan in New York City, approximately 0.5 miles north of Wall Street, and is owned and operated by the Port Authority of New York and New Jersey (PA). As part of the WTC site redevelopment the New York City Transit Authority?s No. 1 subway line which runs through the site below grade, was underpinned so that the soil beneath it could be removed along with the rest of the new east basement excavation. Consequently a scheme comprising micropile installation through and around the existing subway box was designed. The subway had to remain in use throughout save for planned weekend outages to allow a portion of the underpinning to be fitted through or on to the existing structure. At times this involved accessing and drilling from within the subway tunnel under short General Order (GO) Subway shutdown periods. At either end of the subway passage through the WTC site jet grout underpinning was designed to provide support and to complete the excavation and construction of the east basement wall in the areas beneath the subway where it was impossible to install a slurry wall. The jet grout blocks thus formed had to be largely installed around the clock during 53 hour long GO weekend outages and had to overcome severe logistical constraints in and over the tunnel. The jet grout blocks had to provide strengths of at least 500 psi at 3 days and 700 psi at 28 days. The jet grouted soil mass also had to have a level of permeability less than 0.03 feet/day (1 x 10-7 m/s). After an extensive trial program and then production testing it was concluded that the glacial till above the rock proved to be a particularly difficult soil strata to collect test data from and hence the level of observational monitoring was increased to progress the excavation works. Throughout the installation of micropiles and jet grout columns extensive monitoring was in place and prompted a variety of working method changes. The work described in this paper was performed by the Nicholson Construction Company/EE Cruz Joint Venture.

Jan 1, 2008

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small- scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single- hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

Jan 1, 2005

By Antal Partos

ATLAS Processing Company Shrevesport, LA initiated a major plant expansion in 1980. SITE Engineers, Inc. provided engineering consultation regarding the foundation of the vacuum unit. Four test borings were drilled and laboratory testing completed for shear strength and compressibility. Vertical drains were proposed to accelerate time rates of settlements. Steel erection was completed by May 22, 1981 with very small < 0.1 in., settlements. Hydrotesting was initiated on July 9, 1981 and completed on August 27, 1981. An average rebound of 0.3 in. was computed resulting into an average net settlement of 0.5 in. This paper describes in detail soil behavior during load testing.

Jan 1, 1992

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau&apos;s programs involved only health and safety research and education, and fuels testing. As the Federal Government&apos;s primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing minerals substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960&apos;s, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970&apos;s, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation&apos;s minerals, metals, and fuels.

Jan 1, 1976

By Rita D. Sylvester

"IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January I, 1965, to December 31, 1969. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January I, 1960;' the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January I, 1960;3 the 5-year list of Bureau publications and articles from January I, 1960, to December 31, 1964.' It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1965, to December 31, 1968, as well as the Bureau publications and articles for 1969."

Jan 1, 1970

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Wellington Pereira Inácio, Fernando Wypych, Sergio Neves Monteiro, Artur Camposo Pereira, Rafael Marangoni

"The efficiency by which an applied load is transmitted from the matrix to reinforcing fibers in a composite depends on the fiber/matrix adhesion strength. This is determined as the interfacial shear strength, IFSS, which may be measured by means of pullout tests that measure the force needed to pull a single fiber out of a block of material simulating the composite matrix. Different techniques are used to perform pullout tests. The objective of this work was to characterize the IFSS of sisal fibers embedded in epoxy matrix through the determination of the critical length pullout curves. As the main results, a relatively small critical length was found for the sisal fiber/epoxy pullout specimens, corresponding to a weaker IFSS. This was compared to other results applying different pullout techniques. Scanning electron microscopy observation identified the mechanism responsible for the weak sisal fiber adhesion to the epoxy matrix.IntroductionSynthetic fiber reinforced composites is today one of the most successful class of materials with increasing industrial applications from house appliances to large airplanes like the modem Airbus 380. However, environmental issues are revealing serious drawbacks related to the fabrication, use and post-use discard of these composites. For instance, the thermoset polymer composite reinforced with E-glass fiber, known as ""fiberglass"" has an energy-intensive fabrication associated with a surplus emission of C02, which is responsible for global warming [1]. Moreover, the glass fiber is considered toxic and also causes long term pollution after being discarded."

Jan 1, 2011

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By W. Rogers

Blast-induced rock mass displacement can have a significant impact on ore loss & dilution. The mischaracterisation of the grade boundaries both prior to, as well as a result of blasting can lead to significant financial losses on account of ore loss and dilution. Ore dilution occurs when waste material is miscategorised as ore and sent for processing or stockpiling, diluting the run of mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorised as waste and sent to the waste dumps, thus never being processed and recovered. Extensive research has been conducted at the University of Queensland over the last fifteen years to understand the impact of blast movement on ore loss and dilution. Recent outcomes of this research have developed innovative tools and techniques to measure and model blast movement. These techniques have been implemented at Ahafo gold mine in Ghana to understand blast movement dynamics and to implement solutions to reduce blast-induced ore loss and dilution. These solutions are validated through controlled trials and have been incorporated into site standard operating procedures to sustain the benefits.

Jan 1, 2012

By A. Davis, C. Webb, J. Sorensen

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM). The mine produced lead and zinc during the first half of the 1900s. Because of acidic drainage and elevated levels of metals in tailings and waste rock, the site was evaluated in 1998 and 1999. After evaluation, the mine was remediated during 1999-2001 by the BLM. Since remediation, values of pH in water samples have been nearly neutral and specific conductance values have been much lower than before remediation. The Grizzly Gulch forest fire of July, 2002, consumed much of the Belle Eldridge site and resulted in greater than normal erosion and sediment flushing during the months following the wildfire. Had the site not been remediated and the tailings emplaced within a capped repository, generation of acidity and off-site migration of heavy metals within sediments could have been severe at downstream locations.

Jan 1, 2007

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

By Nicole Peter

When introducing digital training technology a practical approach helps address cultural concerns.  Solutions to help create acceptance are discussed.  Resistance to change may be deeply rooted in traditional mine training personnel.  Traditional training staff members may consider themselves less digitally-savvy and resist technological methods available to them. A transitional approach intended to help mitigate or resolve resistance is presented as a continuous improvement pathway toward full adoption.  This presentation contends every mine should welcome the benefit of a digitally connected critical enabler.  The adoption of a digitally savvy learning centre is often viewed a disrupter to existing practice.  Given a commitment-driven learning centre model, technology offers the opportunity to transition from a compliance-based training model to one of competence.  Learning and Development practitioners should welcome the latest advances in neuroscience, Bloom’s taxonomy of learning model, and principles which guide mine safety training as outlined by the Lowell Institute for Mineral Resources at the University of Arizona. By employing digital applications to include animation, game-based simulations and immersive Virtual Reality (VR) these technologies create a viable digitally-savvy learning centre. We will outline the ingredients of a digitally enabled, or VR, Learning Centre to offer some observed benefits, successes, and potential short-comings. Much excitement in the industry surrounds implementation of simulation and/or VR headset training.  Given fair consideration of these as a ‘fit-for-purpose’ solution we examine the paradigm shift required to create real results for on-the-job learning.  Interim steps may be needed to meet the cultural transformation.   Simpler forms of VR, in the form of 3D models and VR environments as displayed on a large interactive touch screen, can serve to bridge this challenge and address a group learning environment. Features of the interactive 3D technology and ease of adoption are presented.  Usage of the touch screen is similar to that of a smart phone. It may be implemented as an obvious transitional tool.  To help describe merits of the interactive touch screen the presentation points out these sample underground and surface mine training applications. There are 3-D simulations such as ventilation, emergency response, support installation, and mine cycle and activity scheduling programs. These applications offer the ability to conduct entry examinations, complete digital pre-use checklists, and perform planned task observations in the virtual world of work. The tool may be used to teach the flow of hydraulics and do fault-finding on machinery such as loaders and dump trucks. Learners may navigate in a virtual mining environment to identify hazards, detect and assess abnormal ground conditions, address poor design features, and alleviate traffic constraints. It is possible to use connected physical controls to navigate machinery in the virtual environment. We conclude the presentation with a “compare and contrast” approach to cite potential cultural benefits by adopting a transitional method. 

May 4, 2025

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

By B D. Burford

High intensity stirred milling using the IsaMill has been the enabling technology for many projects by transforming the economics of fine grinding and simplifying circuit design. IsaMill grinding technology was originally developed for large-scale grinding to P80 sizings of 7 ¦m. The IsaMill is a high throughput, high efficiency mill that produces sharp product size distributions in open circuit configuration. The ability to grind in an inert environment, using a wide variety of media types, can give further metallurgical and economic benefits. The high energy intensity results in a small footprint that enhances the ability to distribute grinding power throughout the circuit, applying grinding energy to the minerals that need it. Recent scale up developments in IsaMill technology have enabled the benefits to be extended to large-scale conventional grind sizes, until now the domain of ball and tower mills. This paper will examine the crossover of IsaMill technology from ultrafine applications into the more conventional grinding area (P80 20 - 150 ¦m). Scale-up developments in IsaMill technology that have enabled this are reviewed. The upcoming commissioning of a 3.0 MW M10,000 IsaMill, the most powerful to date, grinding to P80 55 ¦m at PPL in South Africa will be discussed, as will the recent commissioning of a 2.6 MW M10,000 IsaMill at Kumtor. Recent testwork at McArthur River, where an IsaMill is being considered as an addition to the primary grinding circuit to replace the current tower mill will be reviewed. The potential combination of HPGR and IsaMill to transform concentrator grinding economics will also be discussed. Large-scale IsaMill technology has the ability to transform circuit design and energy efficiency for both coarse and fine grinding.

Jan 1, 2006

By J. P. May

This U.S. Bureau of Mines report identifies and evaluates factors responsible for dump-point accidents involving mobile mining equipment. Information regarding the occurrence and severity of the accidents, the industries affected, the types of equipment involved, the primary and contributing causes, and pertinent Federal regulations is included. The aim of this report is to provide information that will aid mine operators in the recognition of hazards associated with mobile equipment operation near the dump points of stockpiles and waste dumps.

Jan 1, 1990

By R. A. V. Raff

Although falls of roof, face and rib (or side) of coal mines were the third ranking cause of disabling accidents in 1966, the accidents from these falls resulted in the most serious injuries and accounted for approximately 50 percent of the total fatalities (I). Further breakdown of these statistics shows that 88 percent of the fatal accidents occurred within 100 feet of the working face and that 96 percent of the deaths were in bituminous mines, with only four percent taking place in anthracite workings. These figures demonstrated the need for improved reinforcement procedures in operational coal mines, and they provided ample justification for research in the area of accident prevention. The purpose of this project was to investigate the use of polymers and of related techniques to achieve rock bonding and reinforcement of coal mine structures, in order to obtain better or permanent ground support (e.g., drifts, entrees, coal and ore passes, galleries, tunnels and shafts) by the fill ing of fissures in the rock, thereby preventing or delaying the onset of serious rock degradation processes.

Jan 1, 1973