Search Documents

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the "strong" rock stratum, but did not correlate well with the design value calculated for the "weak" rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2005

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By S. Kraemer

Consumption of plastics has been growing in both the U.S. and world markets since the mid-1930s. This growth is due to plastics being used to make new products and as a replacement material for existing products. This paper develops an understanding of the replacement process by looking at the use of plastic, specifically PVC, in the construction pipe industry. History details the growth of the plastics industry and a discussion of the material selection process indicates the advantages and disadvantages of plastic pipe. Analysis shows that the use of plastic, as an alternative material for pipe, is having a significant effect on the cast iron, copper, clay, and steel industries. For the purpose of understanding the replacement process, three example residential systems were examined with a lifecycle cost analysis being performed. PVC was the material of choice in 1988 for all systems. Even though disposal cost was the one area where PVC was not the most cost effective, disposal costs were not sufficient to offset the overall advantage of using PVC on an economic basis. That plastic competes effectively with other materials, in terms of material properties and cost, indicates that further work should be performed to understand the impact plastics have on other material markets.

Jan 1, 1991

By A. J. Teske

Sustainable Development is a very broad initiative in the mining industry, with major components running over the entire life of the mine. It likely commences with pre-exploration permitting and continues to post-mining final closure and possible land reuse. Most major mining corporations embrace the sustainability initiative, either out of a sense of social responsibility or out of necessity in order to continue doing business. But many may view the overall initiative as an added ?cost of doing business.? In many elements of sustainability, there clearly can be added cost ? some as simple as complying with self-imposed sustainability reporting. Fortunately, one major element of sustainable development can clearly be shown to reduce costs ? energy resource management. This paper will describe how the mining industry sustainable development effort differs from other industries, but can benefit from their experience in energy resource management. The mining industry can utilize proven methods from other industries to further their energy management efforts. In addition, many of the resources developed and employed to promote better energy resource management in non-mining industrial settings will be listed.

Jan 1, 2010

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA's general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

By Paul. E. Pesonen

Since early in 1940 the Bureau of Mines has been concerned with possible means of utilizing manganese-bearing materials from the Missouri Valley manganese deposit. During the period between July 1945 and August 1947, the Bureau of Mines undertook to complete certain phases of the problem by re-evaluating the results of earlier work and supplementing the findings by additional operations and field studies considered necessary to permit drawing of final conclusions. Distinctive discoloration marks the outcrop of the manganese deposit which is exposed on both flanks of the Missouri River Valley and its major tributaries for a peripheral distance of approximately 523 miles in south-central South Dakota. The apparent magnitude of the deposit, judged largely from observation of the outcrop, had led to much speculation as to its actual value in terms of tonnage and grade. Similarly, investigative work aimed at developing a means of winning a usable manganese-rich product from the deposit had reached no conclusion, except that certain methods showed more promise than others for accomplishing the final objective.

Jan 1, 1948

By B Twidle, D Bertoldi, J Meikle, R Dunne

The Waihi Gold Mine is situated in a high rainfall area (annual average of over 2 m) on the North Island of New Zealand. Water treatment and discharge at the mine has been ongoing for the last 25 years. The first water treatment plant consisted of a æstandardÆ water treatment facility (ferric chloride precipitation) and cyanide detoxification. With time the project has expanded and the volumes of water increased requiring additional treatment methods (reverse osmosis) to meet the water quality for discharge. This paper will provide information on the historical development of the water treatment flow sheets, performance data and operating costs.CITATION:Bertoldi, D, Dunne, R, Twidle, B and Meikle, J, 2013. Water treatment at the Waihi Gold Mine, in Proceedings World Gold 2013 , pp 503-508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By X. M. Prévost

The reassessment of coal reserves has become a matter of urgency and has come as a result of the present situation of the industry, in the context of globalized coal economies, as well as new mining legislation and the advantages and difficulties of domestic coal suppliers. The de Jager report concerning coal reserves, released twenty years ago, can no longer be used as an estimate for accurately forecasting South Africa’s future coal production. The new reserve and resource study will promote the diversification of energy sources and provide a clearer view of the future of coal mining in the country. With plans to increase South Africa’s coal export capacity to approximately 84 million tons by 2005, it is uncertain whether the country really has sufficient reserves to meet this expansion, as well as satisfy the projected increase in inland demand. The face of South Africa’s coal industry and by association, the economy of our coal-dependent country, are both set to change. This is mainly due to factors such as the demise of most of the large collieries over the last approximately twenty years, growing numbers of economic empowerment producers, the emergence of strong competition in the export market, the dawn of Clean Coal Technologies (CCTs) and the Kyoto Protocol The paper will attempt to dispel some of the current myths about coalfields and reserves and highlight potential areas of high quality coal reserves, available mainly to new entrants in the industry. Keywords: Central Basin, Clean coal technologies, Coal combustion, Coal exports, Coalfields, coalLink, Coal reserves, Coal resources, Coal processing, Colliery, Economic empowerment, Discards, Fluidized bed combustion, Low-ash coal, Metallurgical coal, Power generation, Pulverized fuel, Reserve blocks, Richards Bay Coal Terminal, Run-of-mine production, Saleable production, SAMREC Code, South Dunes Coal Terminal, Steam coal, Synthetic fuels.

Jan 1, 2003

Granduc lies near the Alaskan border in British Columbia, about 600 miles (960 km) north of Vancouver. Prospecting in the area must take place in the short summer months of fog and rain because the winter is bitter cold, with snowfall up to 960 inches (24.4 m) accompanied by avalanches. Despite these difficulties, the mineral ized area was discovered in the 1920's. By 1956, Newmont Mining Corporation had developed mineable ore reserves estimated at 32,500,000 tons of 1.93% copper. Newmont and ASARCO, in a joint venture, then began development of the ore body, which was partially covered by glaciers. It was apparent a concentrator could not be built at the mine site where overland access was impossible due to the weather conditions and the terrain. Years of engineering studies of all possible access routes finally dictated the driving of an 11 mi long (17.6 km) tunnel passing under three glaciers and three mountain ranges to the nearest feasible concentrator site at Tide Lake. Even then, a mountain road subject to an average snowfall of 800 in. (20. 3 m) had to be built 32 mi (51 krn) from the concentrator through Alaska to Stewart, British Columbia, the nearest port. At Stewart, which is located at the head of a fjord 120 mi (192 krn) from the Pacific Odean, a fully equipped marine terminal was built. The tunnel, the lifeline between mine and mill, was to be driven from both ends; however, in 1965, an avalanche occurred at the Leduc portal, killing 26 crew members and wrecking much of the camp. The tunnel was then driven from one heading adjacent to the concentrator site at Tide Lake, a distance of 53,744 ft (16,381 m) to a point under the ore body. The remote location, type of terrain, and bad weather made supply of crews, equipment, and construction materials difficult; but in spite of these extremely adverse conditions, the tunnel crews set many world records. Mineralization throughout the ore zone is generally uniform in grade and composition and is primarily chalcopyrite and pyrrhotite associated with pyrite. Mining is mainly by sublevel caving. After blasting, rubber-tired load-and-haul equipment moves from level to level by means of an internal connecting ramp system on a 15% slope. At the gathering haulage level, 15-ton bottom-dump cars deliver the ore to a 600-ton pocket equipped with a Hudson "Rock-Flo" dump. The bottom of the ore pocket forms the feed chute to the primary

Jan 1, 1978

By K. Morin

"Silver and gold leaching by cyanidation is a well-known process used around the world. This reaction is often accompanied by the leaching of other species throughtout the cyanidation circuit that causes the diversion of cyanide towards non valuable by-products (SCN-, Cu(CN)x, Fe(CN)x, etc.). One of the detrimental impacts of the formation of these by-products is the precipitation of silver-cyanide complexes that occurs when cyanide concentration is too low. Without any extra-addition of free cyanide, the precipitated silver is lost and cannot be recovered causing an important economic loss. To overcome silver precipitation, cyanidation circuits are often operated at higher cyanide concentrations. Recently, COREM’s research team has been working on a technology to measure and control silver precipitation during the cyanidation process. Moreover, a methodology has been elaborated in order to evaluate threshold cyanide level which corresponds to the cyanide concentration at which silver starts to precipitate. This technology has been tested on site on a real cyanidation circuit at Agnico Eagle’s LaRonde mine."

Jan 1, 2014

By L. H. Michaud

An existing mining company plans to extend their surface coal mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accounting for the site show an overall NP:MPA ratio of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to? be mined. If traditional dragline mining methods were used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of Acid Mine Drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. In order to prevent the formation of AMD, the company has proposed to mine the area using Truck/Shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, a mine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil in order to achieve an overall net alkalinity in all spoil areas. Mining of this site should therefore not result in the formation of AMD.

Jan 1, 1994

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By Holt L. Farley

This report describes the development of an electronic system which detects unsafe slack and overload conditions in underground mine hoist ropes. The Slack and Overload Rope Protection System (SORPS) includes a fail-safe load cell inserted between the rope and the conveyance, and an accelerometer mounted on the conveyance. Signals from these transducers are telemetered via a radio link to the hoist control room, where they are combined with drum speed and chair status in a microprocessor-based decision and display unit. Abnormally high external force levels are detected as discrepancies between rope tension and cage acceleration; conveyance weight is inferred continuously. Hazardous conditions are displayed to the hoist operator, along with general hoist status. The system has been tested in a working mine for approximately two years. The report contains specifications, design data and field test experience generated under the SORPS program. It also includes information on dynamic modeling, vibration environment, the status of existing slack detection systems, and applicable control strategies.

Jan 1, 1983

By Sandra Lúcia de Moraes

O presente trabalho visou contribuir para o melhor entendimento do mecanismo inerente ao uso de agente coloidisante/dispersante no processo de pelotização de concentrado de minério de ferro. Avaliou-se a influência dos agentes coloidisantes em comparação aos aglomerantes Peridur e bentonita. Para este fim, foram realizados ensaios de bancada visando a identificação de possíveis ações destes agentes no grau de dispersão das misturas, bem como a sua influência na liberação/aglomeração dos finos. Os resultados destes parâmetros foram confrontados com os resultados de caracterização das pelotas confeccionadas com os diferentes agentes pelos quais foi possível identificar que os dispersantes tem forte atuação sobre o conteúdo de finos do concentrado de minério de ferro. A ação principal se dá pela remoção das partículas ultrafinas que recobrem os grãos mais grosseiros presentes na amostra e as dispersam, no caso dos dispersantes, aumentando a disponibilidade do conteúdo de finos <4 µm, principalmente os finos <1 µm (coloides). No caso do aglomerante orgânico, observa-se também essa ação, no entanto, os finos presentes são aglomerados na faixa entre 26 e 4 µm.

Aug 16, 2017

By Fred N. Kissell

This handbook describes effective methods for the control of mineral dusts in mines and tunnels. It assumes the reader is familiar with mining. The first chapter deals solely with dust control methods, regardless of the application. It is a brief tutorial on mining dust control and will be of help to the reader whose dust control problem does not conveniently fit any of the mining equipment niches described in later chapters. The subsequent chapters describe dust control methods for different kinds of mines and mining equipment. This includes underground coal and hard-rock mines, as well as surface mines, stone mines, and hard-rock tunnels. Because dust sampling has so many pitfalls, a chapter on methods used to sample dust is included. For those occasions when there is no practical engineering control, a chapter on respirators is also included. Except for those listed as ?future possibilities? in the longwall chapter, the dust control methods described are practical and cost-effective for most mine operators. If controlling dust were a simple matter, dust problems in tunnels and mines would have been eradicated years ago. Unfortunately, most underground dust control methods yield only 25% to 50% reductions in respirable-sized dust. Often, 25% to 50% reductions are not enough to achieve compliance with dust standards. Thus, mine operators must use several methods simultaneously, usually without knowing for sure how well any individual method is working. In fact, given a 25% error in dust sampling and day-to-day variations in dust generation of 50% or more, certainty about which control methods are most effective can be wanting. Nevertheless, over the years, some consensus has emerged on the best dust control practices. This handbook summarizes those practices.

Jan 1, 2003