Search Documents

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By R. Hammen

Processes are needed to rapidly and cost-effectively produce highly pure lithium salts for the rechargeable battery sector. Lithium purification is a chemical engineering challenge, due to the low concentration of lithium compared to sodium, potassium, magnesium, calcium, and transition metal ions commonly occurring in lithium brine resources. We describe a Solid Phase Extraction (SPE) process that rejects sodium and potassium, while binding lithium and other higher valent ions. Lithium is then harvested by selective displacement from the SPE column. The rapid equilibration kinetics of SPE composites enables these ion separations to occur in a small SPE column and in one column stage. The chemical parameters of the process are described.

By N. Z. Jovanovic

Irrigation of agricultural crops may be a cost-effective option for the utilization of gypsiferous minewater as it may also create an opportunity to produce crops during the dry winter season on farm sin South Africa, such as in Mpumalanga. In this study, intensive field monitoring systems were developed and implemented to assess the feasibility and sustainability of irrigation with gypsiferous mine water. Soil water and salt balance components, as well as crop yields, were monitored in field trials carried out at Kleinkopjé and New Vaal Collieries (Anglo Coal), and at Syferfontein (Sasol). Field measurements indicated that high crop and pasture yields can be obtained, provided fertilization and irrigation water management are appropriate. Soil water and salt balances indicated that considerable amounts of minewater can be used and considerable masses of salts can be removed through precipitation of gypsum in the soil profile. With appropriate management, water and salt runoff and salt leaching can be intercepted, thereby minimizing the impact on groundwater. The SWB model is being validated through on-going monitoring. This will allow the use of the SWB model at other sites to predict the long-term impact of irrigation with mine water on soil and groundwater, as well as to run scenario simulations in order to recommend sustainable management of irrigation with minewater.

Jan 1, 2004

By Tom Meikle

Long tendon support systems provide several challenges when used in-cycle as part of the secondary or primary support cycle. A two-component pumpable resin, Carbothix, has been in development for use with self-drilling rock bolts, but many of the attributes of this new resin system make it ideal for grouting long tendon support systems. While neat Portland cement grouts or polyester resin capsules have been used with long tendon support systems for many years, two-component pumpable resin systems overcome many of the shortcomings in these systems. The two-component systems dramatically improve the set-time to enable mining face advance with fewer delays, enable longer pumping distances, improve quality control, and enhance load transfer mechanisms. This paper describes the key benefits associated with a new pumpable resin and details the Australian Department of Mines and Petroleum department atmospheric testing results and cable load testing completed by Minova personnel to date. It also details the results of the Australian mine site trials and the introduction of these systems into production use.

Jan 1, 2012

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986

By R. H. Richards, A. E. Woodward

In Rittinger's Aufbereitungskunde of 1867 occurs (p. 195) the following table, which shows the rate of falling in water of fragments of minerals, of irregular shapes and of five different specific gravities: Diameter of particles in millimeters. 10 8 6 4 3 2 1 .5 Sp. Or. Velocity in meters per second. Auriferous silver, 16..9 .8 .7 .57 .5 .4 .29 .20 Galena,. ..7.5 .62 .55 .48 .39 54 .28 .20 .14 Pyrites,. ..5.0 .49 .43 .38 .30 .26 .22 .15 .10 Quartz,. ..2.6 -30 .27 24 .19 .17 .14 .10 .07 Coal,. ..1.3 .13 .12 .10 .08 .07 .06 .04 .03 With the purpose of extending this valuable table, to cover a larger number of minerals and sizes of each mineral, and of making it more easy of application in deciding upon a sieve-scale for any group of minerals, we have prepared the curves of velocity of fall of bodies in water shown in Plates I., XI., 111. and IV., using Rittinger's formula V= 2.44d(8 —1) where V= velocity in millimeters per second. " D = diameter of particles in meters. " 8 = specific gravity of the mineral. These curves embrace a large number of specific gravities, and for each specific gravity the relation of the diameter of the mineral particle to the velocity of its fall in water is given for all diameters and velocities used in practice. The second diagram is an enlargement of the lower left-hand corner of the first, the third bears the same relation to the second, and in like manner the fourth to the third. Plate I, therefore, covers the work of the coarsest jigging 2 inches in diameter; and under

Jan 1, 1890

By Dianne C. Marozas

The U.S. Bureau of Mines is conducting research to evaluate the potential for developing an in situ leach mining process that will selectively extract manganese from oxide ores, leaving gangue relatively undisturbed. To accomplish this, a geochemical approach, based on deposit-specific information such as mineralogy and geology, is used to constrain the operating parameters of the system. Among the studies being conducted are (1) leaching experiments to define reaction mechanisms and kinetics, (2) detailed petrologic characterization at the microscopic scale to assess Mn distribution and leaching efficiencies, (3) deposit characterization and evaluation, and (4) development of potential Mn recovery schemes. Data from these studies are being used to develop engineering design information for an in situ mining process. Specific details of the Bureau's research project are discussed, including results obtained to date.

Jan 1, 1991

This Bureau of Mines publication summarizes the industrial minerals industry of Idaho. It contains information on 119 principal deposits of 21 commodities in the State and describes the institutional and infrastructural factors affecting mineral development.

Jan 1, 1991

By Edward A. Barrett, Roberta A. Calhoun

Introduction This Instructor’s Copy contains most of the information needed to use the Wearing Hearing Protection Properly 3-D training reel. It offers practical suggestions on how to use the reel as a training aid, performance objectives for deciding if the training is appropriate for your needs, and discussion notes that provide additional information to the user. The 3-D reel was designed as a self-teaching aid that drillers and others who work at a drill site can use wherever the opportunity for such training presents itself. The latter could be a company preshift requirement or a tailgate session where workers would have an opportunity to view and discuss the reel. It could also be an individual looking at the reel in a pickup truck prior to beginning work at a drill site. The 3-D training reel is versatile in that it can be used for a small group of persons or for a single worker. For any of these situations, information is transferred to the individual by viewing each of the seven colorful, in-depth 3-D scenes and relating the words that appear in each scene to what is depicted in the visual. Acknowledgment The authors thank Linda J. McWilliams, Statistician, NIOSH Pittsburgh Research Laboratory, for her assistance in analyzing the experimental data in this document.

Jan 11, 2004

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 118-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

By Staff

This U.S. Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles.

Jan 1, 1989

By Lachezar Tsotsorkov

Corporate social responsibility Is a principal trend of the corporate strategy for sustainable development of Assarel-Medet JSC ? the largest Bulgarian company for open pit mining and ore processing the production activities of which date back to 1964. Sustainable development Social responsibility is considered as one of the three pillars for sustainable development, together with the economic and environmental responsibility.

Aug 1, 2013

By Anna M. Ferrero

Stability condition of underground excavations have to be assessed to guarantee safe operations within the quarrying working areas. This objective requires a reliable assessment of the rock mass natural state of stress and of the stress redistribution induced by the excavations. This goal is often complicated by difficult geological conditions induced by tectonic stresses, complex topographies and large and irregular excavation geometries. Consequently, the acting state of stress needs to be measured by specific in situ measurement devices. This work refers on an in situ measurements campaign carried out by CSIRO tests in an underground quarry located in the Carrara marble basin. The difficult path carried out for interpretation of the measurements is described in this paper. In particular, the numerical modeling performed using the Boundary Element Method (BEM) first, to study the influence of both surface topography and excavation geometry and then the Distinct Element Method (DEM) to evaluate the influence of rock discontinuities in the measurement zone are illustrated in this work. Parametrical analysis of the rock mass mechanical features is also described in order to calibrate the numerical models and analyze the experimental results. The work has been carried out trough several phases, which are: characterization of the rock mass through geostructural surveys: this allowed us to classify the rock mass and determine the mechanical and physical parameters necessary for modeling; on-site measurement of stress levels through the application of over coring techniques; numerical analyses for the simulation of excavation phases, using the Examine3D (BEM) engineering analysis code. comparison between the measured stress levels and those numerically calculated and subsequent calibration of the BEM model; Numerical model of the forecasted excavation based on the calibrated (BEM) model.

May 1, 2009

By Ramón Alanís, Filiberto Orrante, Andrea Festa, Baldomero Gutiérrez, Fernando Cornejo

"SGS implemented two rules-based fuzzy logic expert applications on two grinding circuits operated by Peñoles Group in Mexico. Both expert systems are based on control strategies that push against process constraints to improve throughput. Based on proven methodologies, the projects also required some new approaches that led to permanent changes to the mill control strategy.This paper provides descriptions of the implementation, operation and performance of both expert systems. It also reviews how improved production rates were achieved through the use of a common set of expert technology tools. An overview of the resulting control strategies implemented on the two circuits is presented. The paper also discusses the identification of the process constraints within each circuit and how these constraints are used within the expert systems.INTRODUCTIONMexico-based mining company Peñoles Group and the Advanced Systems group at SGS, formally known as MinnovEX Technologies Inc., collaborated on the implementation of two expert systems in two grinding plants, both located in Northern Mexico.The primary objective of the expert systems was to increase throughput whilst still maintaining the cyclone overflow product size within an acceptable range. The secondary objective was to achieve a high level of utilisation of the expert technology.In order to achieve these objectives, SGS proposed a proven methodology which leveraged the existing operating and technical expertise at site through the client’s involvement in the design and implementation stages. The in-house operating and technical expertise of SGS was also brought to the project and implemented with the client’s approval at all stages. At both sites the final acceptance was defined upon meeting both process and utilization parameters.The development and deployment of rules-based fuzzy logic applications has matured as a technology and consequently, clear definition of process states and their place in the logic structure to control a given circuit are now transferable. The key to the robustness of the control logic depends on selection and tuning rules for maintaining stability and optimizing a given circuit. Application integrators need to have a standardized approach for timely integration and deployment; a critical component to avoid the common critiques that expert applications are idiosyncratic and difficult to maintain."

Jan 1, 2009

By A. D. Hahn

This report describes and gives the results of an examination by the Federal Bureau of Mines of ilmenite-bearing placer sand deposits in the 24-mile long valley of Otter Creek, Kiowa and Tillman Counties, Okla. Drilling and sampling was completed in three periods between October 1956 and September 1957. Mineralogic studies and mineral-dressing tests on recovery of ilmenite and other heavy minerals from composited samples of the sands were made in Bureau of Mines laboratories at Rolla, Mo., in 1957 and early 1958. Otter Creek rises in and drains the southwestern extremity of the Wichita Mountains, which are represented locally by knolls and ridges of gabbro and granite surrounded by plains floored with flat-lying Permian red beds. The valley fill consists of a basal sand-clay component, derived from weathering of the igneous rocks, and an overlying silt-clay alluvium. Ilmenite is present in significant quantity and recoverable grain size only in the basal sand-clay.

Jan 1, 1960

By Alvear G. R. F. Flores

It is now 35 years since the organization of the first sulfide smelting conference in 1983. Since then, the smelting base metals industry has experienced several changes driven by the necessity to improve economic, operational and environmental performances and resource efficiency and meet the increasing market demand for metals. In this continuously challenging environment, it is relevant to recognize which are the main challenges that the industry will face in the coming years and critically address our preparedness to respond to them. This analysis have to consider not only the effort required from the fundamental research and technology aspects but also how these pillars interact with the drivers behind the base metals industry. This paper discusses some relevant aspects required to continue developing the base metal industry focusing on copper. Aspects such as the need to supporting the generation of fundamental metallurgical knowledge, acquisition and proper use of data with advanced analytics methods, technological innovation to develop sustainable process flowsheet are discussed with emphasis on efforts conducted by Aurubis.

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

This research investigates roof deformation and failure characteristics, as well as mechanical interaction between the panels of the roof strata above two adjacent working faces in a steeply inclined coal seam. Physical modeling with photogrammetry measurement method has been employed in this investigation. The movement of roof strata and section pillar, as well as the stratum morphological characteristics, was quantitatively analyzed. Results show that the roof movement direction above the two panels has zoning characteristics, especially in the lower panel. Roof migration in the lower panel of the working face is larger than that in the upper panel. The roof to floor closure perpendicular to the seam direction is larger than the sliding along the seam. The maximum roof concave and convex bending occurred at the middle and upper parts of both panels; the roof bending in the upper panel mining area indicates a larger mining disturbance induced by lower panel mining. The void ratio contour of the lower panel is an asymmetrically arched shape, which is different from that of the upper panel area. The higher roof strata above the upper panel exhibit separation and breaking, whereas the lower roof exhibits compression due to mining in lower panel. The section pillar is compressed and slides slightly, which aggravates the mechanical interaction between the panels and increases the caving height of the roof over the lower panel and the periodic weighting intensity

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

This research investigates roof deformation and failure characteristics, as well as mechanical interaction between the panels of the roof strata above two adjacent working faces in a steeply inclined coal seam. Physical modeling with photogrammetry measurement method has been employed in this investigation. The movement of roof strata and section pillar, as well as the stratum morphological characteristics, was quantitatively analyzed. Results show that the roof movement direction above the two panels has zoning characteristics, especially in the lower panel. Roof migration in the lower panel of the working face is larger than that in the upper panel. The roof to floor closure perpendicular to the seam direction is larger than the sliding along the seam. The maximum roof concave and convex bending occurred at the middle and upper parts of both panels; the roof bending in the upper panel mining area indicates a larger mining disturbance induced by lower panel mining. The void ratio contour of the lower panel is an asymmetrically arched shape, which is different from that of the upper panel area. The higher roof strata above the upper panel exhibit separation and breaking, whereas the lower roof exhibits compression due to mining in lower panel. The section pillar is compressed and slides slightly, which aggravates the mechanical interaction between the panels and increases the caving height of the roof over the lower panel and the periodic weighting intensity