Search Documents

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By Michael A. Trevits

Since the promulgation of the MINER Act and the follow-up changes to the regulations governing mine seal construction and maintenance, mine operators must be acutely aware of the atmosphere in sealed mine areas and prepared to deploy control technologies when the conditions are warranted. On Site Gas Systems1 in Newington, Connecticut was awarded a contract by the National Institute for Occupational Safety and Health (NIOSH) to construct a novel in-mine nitrogen (N2) generation plant using pressure swing adsorption (PSA) technology. PSA technology utilizes carbon molecular sieve material and pressure to adsorb oxygen (O2) molecules while allowing N2 molecules to pass through the sieve material. The prototype PSA unit was tested at the NIOSH Safety Research Coal Mine (SRCM) where a 62,000 ft3 area of the mine was rendered inert during a series of two tests. The resultant data were then used to construct a CFD simulation of both injection tests. In addition, O2 depletion and gas leakage rates were quantified in the model and were compared to actual values. Once the model was calibrated, the sealed mine area was doubled and simulations were made with various injection rates and injection site locations to determine the impact on the time needed to render this area inert. This paper presents an overview of the PSA plant, the details of the gas injection tests and CFD modeling work.

Jan 1, 2010

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

By Joseph Grumer

About a century ago Bunsen and his associates invented the famous burner that bears his name and was to become the ancestor of today's gas appliances. Over the years, Bunsen's invention became the starting point of a highly developed, practical technology that culminated in the gas industry as we now know it. However, it did not occur to the early workers to investigate the scientific potentialities of the new device, and as a result the science of gas-burner performance did not keep pace with the growing industry. It was with the objective of closing the rapidly widening gap between science and technology that the present research was undertaken Its immediate purpose was to provide basic information on the combustion characteristics of .fuel gases, in particular as they affect flashback, blowoff, and yellow tipping. Information obtained in the present research and contained within this report consists of the following: (1) Fundamental flashback and blowoff characteristics have been determined, it is believed, for all fuel-gas mixtures in which the gas industry may be interested. These are critical boundary velocity gradients for flames in free air, on burners with ports at room temperature and pressure. Burner aeration is characterized by the parameter, fraction of stoichiometric. These basic limits are explained, values are presented, and calculation procedure is given for deriving corresponding values of port loading and percent primary air (chs. I and II).

Jan 1, 1956

By A Minchinton

With blasting, all far-field phenomena including, but not limited to, stress wave propagation, fracture, vibration and muck pile formation are intrinsically and irrevocably dependent upon near-field phenomena or mechanisms that we describe using physics-based mathematics typically transcribed into computer codes. The energetics involved in such near- to far-field transitions are not fundamentally relevant as they are simply progenitors of these processes.The notion of explosive energy as a descriptor for explosive or blasting performance is a case in point. These energies, which are generally used in blasting tables, are almost exclusively based on ideal detonation theory alone and do not include the influence of the rock, charge diameter, blasthole length and the late-time dynamic expansion that can be predicted using codes based on non-ideal detonation theory.With decoupled charges in presplits for example, the pressure drop between the charge and the blasthole wall can be simply described to first order using the energy relationship associated with adiabatic expansion. However, a more realistic mechanistic solution involves interacting fluids and turbulence leading to dynamic processes such as the channel effect.CITATION:Minchinton, A, 2015. On the influence of fundamental detonics on blasting practice, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 41–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Charles T. Harper

The uranium deposits discovered by Amok (Canada) Ltd. in the Cluff Lake area of north western Saskatchewan occur at or near the southern edge of the uplifted basement core of the Carswell circular structure. Two types of mineralization, distinguishable, by their geological and structural setting and mineral paragenesis, have been recognized. The N-Claude type is characterized by a relatively simple mineral assemblage, consisting of uraninite or pitchblende with coffinite, and is accompanied by variable amounts of graphite and organic matter, and Fe, Cu, Pb and Mo sulphides. Both N and Claude orebodies occur within quartzofeldspathic gneisses of the basement core. On the other hand, the D-type ore has a complex mineral assemblage consisting of: uraninite, pitchblende, thucholite and coffinite, along with native gold and selenium; gold tellurides, and selenides of Pb, Bi, Ni and Co; sulphides of Fe, Cu and Pb; and organic matter. The D orebody occurs within carbonaceous shales at the base of the Athabasca Formation as well as in fault zones in regolithic quartzo feldspathic gneisses above the inverted unconformity. An age of 1050 m.y., which is consistent with a period (circa 1200-1000 m.y.) of widespread hydrothermal activity and uranium mineralization or reworking within and adjacent to the Athabasca Basin, has been obtained from uranium mineralization from the D orebody. Later reworking (circa470 m.y.) of the mineralization occurred at the intersection of older mineralized shear zones with radial faults produced during meteorite impact.

Jan 1, 1978

By Bill A. Hancock

In Situ leaching for the recovery of uranium from low grade sandstone deposits is one of the newest technological advances in the mineral industry. It is rapidly developing into a commercially feasible mining system which has economic, environmental, and social advantages over conventional mining systems. Because of the current uranium shortage, development of In Situ leaching into a sophisticated system has gained new impetus. In Situ leaching will become an important mining technique in the future, which will greatly help to supply uranium for our nation's energy heeds. In this paper, I will be giving an overview of the merits of the system, as well as the technology, problems, and research in solution mining of uranium.

Jan 1, 1977

By John Convey

"IRON ORE was first smelted in Canada about the year 1736 at Les Forges, Quebec -a most appropriate name for such a historic locale. During these early years of the 18th, 19th, and first quarter of this century, about six million tons of ore were mined and employed in the manufacture of items ranging all the way from kettles, stoves, and cannon for the early settlers to weapons of war for the allied armies of World War I.But this symposium on iron ore is not concerned with this early period. Instead, it is concerned with the iron ore industry of today -an industry which will soon be-come one of the two most valuable mineral industries in Canada.The subject in its broad geographic and economic aspects will be introduced by Mr. Buck; Dr. Harrison will describe the geology and origin of the principal iron ore deposits; Dr. Downes will go into beneficiation as it applies to iron ores; and Mr. Gertsman will discuss primary processing. The symposium will not deal with the steel end of the industry, because that phase itself could well form the subject of a symposium."

Jan 1, 1955

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Robert Stefanko

With passage of the Clean Streams Act of the Commonwealth of Pennsylvania and its impact on the coal industry, considerable research has been conducted to explore various approaches to the problem, including deep-well disposal. Available drillhole data from gas and oil wells were used to develop cross -sectional maps for various portions of the state and potential disposal zones were evaluated. Bethlehem Mines Corp., faced with a severe water problem at its Marianna operation in Washington County, cooperated with the Dept. of Mining at The Pennsylvania State University in establishing a 1500-ft well into the Salt Sands for the purpose of determining the feasibility of mine water disposal. The thickness, porosity, and permeability of the formation at the well site proved to be below what had been anticipated from drillhole data. Further, subsequent hydraulic fracturing did not improve the flow characteristics of the well; pumping pressures remained in the range of 1800-2000 psig for disposing of water at the rate of 150 gpm. The legal problems of disposal at the site were very formidable. When the Salt Sands proved to be less than satisfactory, permission could not be obtained to dispose in other promising formations. The paper details many of the problems associated with the experimental well and makes an assessment of the potential for deep-well disposal of mine water. The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given e1sewhere.l,2 The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania. Enactment of more restrictive clean-water legislation in Pennsylvania recently had a great impact on the coal industry. Among its provisions was the reclassifica-tion of most mine water as industrial waste whose dis-posal is prohibited in any stream of the Commonwealth. This had the effect of accelerating research in a variety of areas, although treatment methods still retained primary interest. When a feasibility study of deep-well disposal was proposed to the Pennsylvania Dept. of Mines and Mineral Industries, the Coal Research Board (CRB) approved it. This paper summarizes the efforts on this project. Acid mine water is a chemically complex liquid. having no definite quantitative relationship among its constituents. However, it is the iron disulfide (FeS2) associated with practically all coal seams that produces the objectionable products present in acid mine water when combined with air and water. The principal contaminants are sulfuric acid (H2SO,) and ferric hydroxide (Fe(OH)2. Ferric hydroxide is a rust-colored gelatinous precipitate that coats stream bottoms and destroys aquatic life. However, other ions and bacteria are present in acid mine water in varying amounts.

Jan 1, 1971

By E. O. RHODES

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining, prepara- tion, and utilization of coal. This mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee, which cooperated with a counterpart British Committee. In some instances; engi- neers from other allied countries cooperated. The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter, Deputy Solid Fuels Administrator. The personnel of the mission consisted of H. F. Yancey, in charge, J. W. Buch, Thomas Fraser, L. L. Newman, and L. D. Schmidt of the Bureau of Minos; H. H. Lowry, Director of the Coal Research Laboratory, Carnegie Institute of Technology; H. J. Rose, Vice-President and Director of Research, Bituminous Coal Research, Inc.; and F. H. Reed, Chief Chemist, Illinois Geological Survey. E. 0. Rhodes, Manager, Development Section, Tar Products Division, Koppers Co., Inc., served on the mission for the Chemical Subcommittee of 1.I.I.C. in Europe. His assignment was the investigation of the coal-tar industry. In this connection he prepared this report on the German Low- Temperature Tar Industry as a companion to his provious report on the German High-Temperature Tar Industry (Bureau of Mines Information Circular 7409). Because of Mr. Rhodes' extensive experience in these fields and the impor- tance of the subject material to the coal producers and those utilizing coal-tar products, both reports are issued by the Bureau of Mines. Over fifty reports were written by the members of the Solid Fuels Mis- elon. These, together with microfilms of supporting data obtained in the course of the investigations, are on file at the Foreign Documents Group, Technical Reports Section, Bureau of Mines, Pittsburgh, Pa., where they are available for examination. Copies of reports available in printed form may be ordered from the Department of Commerce, Office of Technical Services, Washington 25, D. C. Check or money order accompanying order for printed reports should be made payable to the Treasurer of the United States. A Bibliography of Scientific and Industrial Reports, covering all ma- terials and subjects and giving instructions for obtaining the desired items, has been published weekly by the Office of Technical Services. Effective July 1, 1948, the Bibliography of Scientific and Industrial Reports will be prepared monthly instead of weekly and on a more selective basis. issue, which will be the first monthly issue, will be available about July The July month thereafter through June 1949. Annual subscriptions and orders for individual copies starting with the July 1948 issue should be addressed to the Department of Commerce, Office of Technical Servicos, Washington 25, ur, and be accompanied by chock or money order made payable to the Troas- Bibliof the United States. Annual subscriptions for monthly issues of the Bibliography of Scientific and Industrial Roports will be $10. Individual issues will cost $1 per copy. Foreign subscriptions will be $14 per year and $1.50 por copy. tions listed in the Bibliography of Scientific and Industrial Reports should All orders for reports in microfilm or photostatic type of reproduc- ורי

Feb 1, 1949

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018

Access to the Rosebery Orebody, which dips into the western slopes of Mount Black at 45¦, has been achieved in sequence by the following means: - A series of adits down to 8 level - An inclined shaft (No. 1 Shaft) sunk internally from 8 level to 14 level - A vertical circular concrete lined shaft (No. 2 Shaft) sunk internally from 4 level to 19 level. Although the orebody has been fairly well defined to 19 level, deeper ore occurrences have been outlined by a series of drill holes decreasing in frequency with depth to 26 level. No. 2 Shaft (sink) was stopped some 10 m below 19 level in order to make an early start on doubled production at West Coast Mines, with the intention of subsequently extending the shaft or of driving a decline from the lowest operating horizon for deeper access. The decline approach was adopted some six years after production commenced from No. 2 Shaft. The reasons for that decision are outlined, together with an account of the constraints and design requirements imposed by commencing by a vertical shaft in the hanging wall of the orebody.

Jan 1, 1982

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By Gregg Vickell

"High tonnage, low grade gold mines such as Omai’s afford economies of scale that are unto their own insufficient to sustain profitability at today’s depressed gold price. Complimenting profitability objectives is the perpetual challenge to reduce operating costs and optimize unit operating efficiencies while being ever vigilant of issues such as environmental control.Key to achieving these objectives at Omai are throughput and availability gains, gold recovery improvements, cost cutting, a skilled workforce and reliable power generation.This paper attempts a cursory review of startup-to-date plant performance advances and future performance-driven objectives.INTRODUCTIONCommercial gold production at Omai commenced in January 1993 with annual output climbing to 250,000 opy by the end of 1994. A mill expansion completed in August 1996 increased gold production to 340,000 opy by the end of 1997. Current milling capacity is 20,000 in tpd (nom.) with actual capacity exceeding 24,000 mtpd on occasion depending on ore size and competency. Mill feed consists of hardrock (andesite, quartz diorite and rhyolite) and softrock (saprolite, laterite) at a nominal ratio of 70:30, respectively. Present day average weighted grade of the feed is 1.4 g/t gold.PROCESS DESCRIPTIONPrimary crushing, ore handling and the original 12,000 mtpd hard and soft rock SABC mill, hereafter referred to as Mill ‘A’, remains essentially as documented by Konigsmann (1 994) complete with poststartup modifications. The mill expansion, hereafter referred to as Mill ‘B’, features an 8000 mtpd hard rock SABC grinding circuit similar in configuration to Mill ‘A’ and differing only in equipment size. Mill ‘B’ includes a 9000 H.P.,reversible variable speed , single pinion drive, 32 ft. x 15 ft. SAG inill , a 7 ft. short head pebble crusher and two parallel 5400 H.P., 16.5 ft. x 30 ft. ball mills with dedicated cyclone packs consisting of D26 hydrocyclones."

Jan 1, 1999

By S McEachern, J Lowe

An important issue currently facing the mining industry in Australia is the management and cost to the industry and other stakeholders of entry into and exit from towns and their communities. These costs can be environmental, social, economic, political or reputational. The ability of companies to engage the trust of stakeholders, including: communities, governments and investors, is critical, and corporate reputation plays a significant role in this. For the industry to secure a long-term and sustainable future, it must have the technical, business and reputation assets to proceed in a cost-effective, environmentally acceptable and socially supportive way. This research assesses reputation as a critical competitive issue for mining companies, as technology and information make mining more predictable; the physical and human assets of mining companies are less likely to be the critical resource in a Resource Based View model of competitive advantage. The proposition is that in mining today, reputation as it facilitates day-to-day operations, regulatory zeal and access to new mine sites will become the rare, inimitable and valuable resource for mining companies. This paper reports on an ongoing research program to evaluate the impact a mining companyÆs reputation(s), with its various stakeholder groups, has on a companyÆs ability to sustain competitive advantage. Integral to this study is to develop an understanding of the relationships between mining companies and their stakeholders, and the importance of corporate citizenship polices to reputation and hence to corporate sustainability. Through the identification of the drivers of reputation for the various stakeholder groups, a model of reputation formation will be developed and also reputation measures for the mining industry in Australia. The preliminary findings of this research, the results of an industry focus group conducted with representatives from regional mining operations, are reported. The industry focus group was designed to enable a better understanding of who are the main stakeholder groups and how they regard mining companies and to inform the second stage of the research project a Delphi Study of the drivers of reputation by stakeholder groups. The aim of this research is to further the understanding of the relationship between corporate citizenship, reputation and performance in the mining industry, thus assisting companies to strategically manage their corporate citizenship investments.

Jan 1, 2006

By Ree Llewellyn

"It has been estimated conservatively that the costs of wear damage and friction in the Canadian mining and mineral processing industry amount to over one billion dollars per year. These are mainly incurred through the repair or replacement of worn parts and production losses from related equipment downtime. The selection and application of the most appropriate wear protection components and systems, can thus have a very significant influence on productivity, profitability and global competitiveness.Details are presented of the wide diversity of materials used to counteract the varied and often complex wear attack mechanisms that occur in surface mining. The majority are various forms of steels and irons with generally very high hardness. However, they also include relatively soft elastomers and polymeric products.The main characteristics and applications of the different classes are reviewed. Case studies record significant performance improvements achieved through more judicious selections. Finally, some new developments which reduce maintenance charges by substantially increasing wear component life, are described."

Jan 1, 1996

By P. A. Cox

The purpose of the initial research performed under this contract was to determine the margins of safety in explosion-proof (XP) enclosures, which were designed and certified according to the current schedule (Schedule 2G). Results from this work provide baseline data on the current schedule, from which a new schedule can be formulated to give equal or greater levels of safety. Results and discoveries in the initial work led to an expansion of the contract to cover, additionally, weld quality in enclosure fabrication, reliability of enclosures with windows and lenses, and performance tests for enclosure qualification. Finite element calculations and hydrostatic tests revealed wide variations in the margins of safety in the enclosures studied; however, only one enclosure had a safety factor which was less than one. Results from a weld quality survey led to the recommendation of AWS Welding Standard D14.4 for the fabrication of XP enclosures. Based on other work, accelerated aging tests were recommended for qualifying plastics and adhesives that are used in some enclosures, and a Structural Performance Test was developed to test enclosure strength for a minimum static pressure of 150 psig.

Jan 1, 1982