Search Documents

By Jorge Beim

Helical Piles are increasingly being used to support and rehabilitate structures subjected to compressive axial loads. Traditionally, empirical correlations between installation torque and load capacity of helical screw piles are used as the field quality control. Load tests, however, are always recommended to validate the installation process and design methodology. This paper describes a test program performed on helical piles installed at the National Geotechnical Experimentation Site of the University of Massachusetts - Amherst campus (UMass-Amherst), well known for its deep varved clay deposit. Seven of these piles were submitted to Dynamic Load Tests using the Pile Driving Analyzer® (PDA), and also to Static Load Tests. Good agreements were obtained between the results of the dynamic and static load tests, encouraging the use of the former testing method as a viable alternative to the latter for determining the compressive load capacity of helical piles installed in cohesive soils. The results of the load tests were also compared to the predictions based on torque correlations, resulting in correlation coefficients which were higher than the ones traditionally used.

Jan 1, 2012

By Richard K. Sandaas

Start Date: April 4, 1988 Completion Date: Dec. 29, 1989 Contractor: SCI Contractors Past and present transportation centers will come together at International District Station, located at the south entrance to the tunnel next to the turn-of-the-century Union Station train depot. The area will bustle once again with activity as commuters and visitors converge on the modern transit station at the edge of Seattle's International District. Buses coming from south Interstate 5 and Interstate 90 will enter the tunnel through this station. [ ] International District Station is an open-air station, 1,060 feet long and 82 feet wide (about 15,400 cubic yards of concrete were used to build the station). A concrete lid over the southern portion of the station staging area is held in place by 131 support piles. The station will include entrances on Jackson Street and King Street. Union Pacific Realty is planning to build an office and retail complex upon the lid. The station also has an international flair. Symbols of the Chinese zodiac will be etched into the station plaza floor. The station platform walls will be lined with large steel panels embellished with designs in origami?a Japanese folded paper art form. [ ]

Jan 1, 1990

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014

By J. S. Stewart

THE Mackenzie River Valley proper extends from Great Slave lake to the Arctic ocean (see map, Figure 1). From Fort Providence, near Great Slave lake, to Aklavik, near the Arctic coast, the distance by river is 1,000 miles. This will give some idea of the extent of the region. Throughout the length of the river valley, the Precambrian complex rocks are overlain by unaltered sedimentary rocks several thousand feet in thickness. These sediments are dominantly marine and Palaeozoic in age. In places, the Palaeozoic strata are overlain unconformable by Cretaceous an Tertiary sediments. The strata have been folded and, in general, the inclination of the beds to the horizontal is comparatively gentle. Here, then, we have the essentials for potential oil fields covering an area over 1,000 miles in length. This is probably the largest comparatively unexplored potential petroleum region in North America, and surface evidences of oil in the form of seepages occur in several places. Many of these seeps were known to the early explorers, and the first Geological Survey report on the Mackenzie River region, containing the results of field work carried out by R. G. McConnell in 1887-88, noted the petroliferous character of the Devonian strata and the indications of petroleum(l). This region is, however, handicapped by distance from markets and sources of supply of materials; by lack of modern transport facilities; by short season for river transport, and mountainous country separating the valley from the Pacific seaboard; and by the long winter season with weather that makes outdoor work difficult. These factors have tended to discourage the enthusiasm of would-be promoters, and so development in this region has been slow In 1920, a test well drilled about fifty miles northwest of Fort Norman discovered oil in commercial quantity, and three additional wells proved a small area to be productive.

Jan 1, 1944

Organization Place Date 1917 American Electrochemical Society Pittsburgh, Pa. Oct. 3-6 American Institute of Mining Engineers St. Louis, MO. Oct. 8-13 American Gas Institute : Washington, D. C. Oct. 16-19 American Institute of Architects Philadelphia, Pa. _ Dec.. 26-29 American Society of Mechanical Engineers New York City. Dec. 26-29 American Mining. Congress State Chapter Phoenix, Ariz. Dec. 26-29

Jan 10, 1917

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By Dennis R. Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson’s effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Dialkyl dithiophosphinates are a unique class of collectors used in the flotation processing of Cu- Au, complex polymetallic, and precious metal ores. They are known to exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive HSE profile. Historically, for most reagents used in flotation, practical methods of chemical usage have preceded detailed scientific understanding of how they work; this applies also to dithiophosphinates. Recently, however, the research community has shown significant interest in this chemistry, and numerous studies have been conducted to understand the fundamentals of interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized by drawing on concepts and insights from coordination chemistry. A comparison between the interactions of dithiophosphinates and dithiophosphate analogues with various minerals and metals is also made throughout. We believe that such a critical analysis/overview will be invaluable in identifying gaps in knowledge regarding this important set of compounds, which in turn may provide a basis for the design of studies that can advance understanding of their flotation performance. INTRODUCTIONDialkyl dithiophosphinates are an important member of the class of thiophosphorus compounds that are widely used in flotation beneficiation of base metal sulfide and precious metals ores. Ore flotation studies and plant practice experience have demonstrated their unique properties compared to the traditionally used sulfide collectors such as dialkyl dithiophosphates (their closest analogues) and xanthates. The predominant dialkyl dithiophosphinate used in the industry today is sodium diisobutyl dithiophosphinate (a.k.a. DIBDTPi; AEROPHINE® 3418A1 introduced by American Cyanamid in the late 1970s; Figure 1). The widest application of AEROPHINE 3418A is found in complex polymetallic ores of Cu-Pb-Zn-Ag, Pb-Zn-Ag, and Cu-Zn where it has demonstrated improved recoveries (and flotation rates) of sulfide minerals of Cu, Pb and Ag and selectivity against sphalerite, iron sulfides, and penalty elements (Mingione, 1991). More recently, it has also been used as a collector in the processing of Cu, Cu-Ni, and Ni ores (Guitard et al., 2015) and Cu-Au ores (Dunne, 2005). In general, it is considered to possess the collecting power of xanthates together with the selectivity (against pyrite) of dithiophosphates (Hope et al., 2003a, 2003b), while requiring lower dosages than those reagents (Guitard et al., 2015). AEROPHINE® 3418A has also found an important place in several targeted formulations to improve flotation performance. Other benefits of this reagent include higher flotation rates, having a better HSE (health, safety and environmental) profile2 compared to xanthate, and exhibiting resistance to hydrolysis and oxidation (Guitard et al., 2015). Compared to diisobutyl dithiophosphate (DIBDTP), which is known to contribute significantly to frothing (often leading to over-frothing), AEROPHINE® 3418A is observed to be froth neutral (i.e. it does not alter the existing froth characteristics). As is the case for other flotation reagents, the design and application of AEROPHINE® 3418A has preceded understanding of its behavior at a fundamental level. Recently, there have been numerous fundamental and application studies designed to develop a better understanding of its interaction with sulfide minerals and precious metals. This should help in optimizing its application in flotation and provide a basis to better rationalize its unique selectivity and activity characteristics. Past studies on the interacti"

Jan 1, 2016

By James B. Cathcart

The potash mine of the International Minerals and Chemical Corp. is about 18 miles east of Carlsbad, New Mexico, in sec 1 and 12, T 22 S, R 29 E, N.M.P.M. Potash is produced from two zones in the Salado formation of late Permian age. The lower zone, consisting of a mixture of sylvite (KCI) and halite (NaCl), lies at a depth of about 900 ft, and the upper zone, in which the principal potassium mineral is langbeinite (K2SO4 2MgSO4), lies at a depth of about 800 ft. Because of the plastic nature of the material, fractures in the Salado formation are extremely rare and have been noted only on the 800 ft level of the International mine. The open fracture described below is almost unique. Only one other open fracture has been noted, and it was on a working face in the same general area as the one described, but was destroyed before the writer had a chance to examine it. According to J. E. Tong, foreman on the 800 level, this fracture was similar to, but smaller than, the one herein described. The saline strata are nearly flat-lying and comprise interbedded layers of halite, anhydrite (CaSO4), and poly-halite (2CaSO4.MgS04.K2SO4-2H2O), with halite predominating. The halite layers contain local concentrations of sylvite, carnallite (KC1.MgCl2.6H2O), and langbeinite. The principal marker in the potash mines area is a bed of anhydrite about 8 ft thick, and 70 ft below the 800 level. This bed contains varying amounts of polyhalite, and locally a few blebs of sylvite. Two principal marker beds are present over most of the 800 level. The lower is the "Middle Salt Marker," a bed of bright-orange halite, which ranges in thickness from a knife-edge to about 0.6 ft, and is usually bounded above and below by thin seams of green or reddish-brown clay. In langbeinite-rich areas, this marker usually contains abundant blebs of langbeinite. The upper of the two principal markers is a green clay seam, containing abundant halite, which ranges in thickness from 0.1 to about 0.5 ft. It is 2 to slightly more than 5 ft above the Middle Salt Marker. No langbeinite of minable grade is found above this clay, and it

Jan 1, 1950

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By Sergei Decterov, Peter Hayes, Evgueni Jak, Taufiq Hidayat, Denis Shishin

Copper smelter operations around the world are under sustained pressure to reduce costs and increase output. Through the provision of reliable data on fundamental properties of the chemical systems the opportunities for improvements of industrial copper production can be identified. Experimental and modelling studies on phase equilibria, thermodynamics of copper slag/matte/metal/gas systems have been combined into an integrated research program undertaken at PYROSEARCH. Experimental phase equilibria studies involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of compositions of equilibrium phases with electron probe X-ray microanalysis (EPMA). Thermodynamic databases development and modelling is undertaken using the computer package FactSage in conjunction with advanced models used for complex solution phases. Progressive development of these research methodologies has brought significant advances in characterisation of these complex systems, including a new optimised thermodynamic database for the copper-containing slag system Cu2O-Al2O3-CaO-FeO-Fe2O3-MgO-S-SiO2.The new data and models can now be applied to assist in improvements of the processes. The effects of changes to chemistry and process conditions within the smelting reactor can be examined. Several examples of new descriptions of the phase chemistry of the Cu2O-CaO-SiO2 and Cu2O-FeO-Fe2O3-SiO2 systems in equilibrium with metallic copper showing calculated and experimental data are presented.

Jan 1, 2014

The design, specification, and performance evaluation of the Communications and Location portions of a Coal Mine Rescue and Survival System are described. The work was performed as part of a nine month effort to develop a mine rescue and survival system using existing technology and state -of-the -art hardware as recommended by the National Academy of Engineering. Three basic subsystems were developed, one for survival, one for communications/location and one for rescue. This report and related equipment manuals describe only the Communications/ Location Subsystem which was designed, fabricated, and tested by the Westinghouse Georesearch Laboratory in Boulder, Colorado. Two basic technologies were used. Electromagnetic signals propagating through-the-earth provide voice downlink and coded beacon up-link communications. Seismic methods were developed to provide means for locating trapped miners. Seismic signalling also provides a backup means for communications. Parallel development programs for the electromagnetic and seismic portions of the system were conducted. The resulting hardware and software have been partially tested in coal mines and under simulated emergency conditions in order to evaluate system performance. The results of these tests are discussed. Further testing is recommended in order to establish quantitative performance limitations tinder a variety of environmental conditions and to develop methods for improving system performance.

Jan 1, 1971

By C. E. M. Meskers

Electronic and Electric Equipment contains a range of components made of a wide variation of metals, plastics and other substances. Up to 60 elements can be found in complex electronic equipment: base metals, precious metals and special metals in circuit boards and batteries. Because of its amount WEEE represents a considerable metal resource with a higher special and precious metal content than found in ores. The Umicore integrated smelter and refinery recovers and supplies back to the market 17 different metals from EEE. Pre-treated materials enter state of the art, material and energy efficient metallurgical processes for environmentally sound recovery of metals and treatment of off gasses and hazardous substances. The organics in the feed function as reducing agent and alternative energy source during smelting for precious metal recovery. Lithium-ion batteries are treated using a dedicated process. As a result the environmental footprint of metals produced from EEE is much smaller than primary production.

Jan 1, 2009

By Claude W. Sill

In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of. Tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate; It seemed likely that the, same general procedure could be used in determining semimicro quantities of uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant its turn permits the use of the very stable indicator, ferroin, with its sharp color.., change and exactly reproducible blanks. Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Gleu. The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months.

Jan 1, 1952

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"INTRODUCTION An extensive test program is in progress by the Bureau of Mines to determine ways and means of recovering ferromanganese-grade ore 6/ from the wide-spread domestic manganese and manganiforous iron deposits. Samples for testing were received from the Interstate Manganese Co. in northeastern Tennessee, 11 miles west of Mountain City and 10 miles southwest of Damascus Va. The ore deposit occurs in the residual material of the Shady dolomite 7/ as an unconsolidated mixture of hard and soft manganese oxides and clay.Numerous tunnels and pits have developed a large reserve of ore in an area of about 15 acres. One pit 250 by 50 by 20 feet is being mined by rower shovels. The ore is hauled to a washing plant for log-washing, hand-sorting, and jigging. Coarse concentrates from the washing plant are marketed without further beneficiation.ACKNOWLEDGMENTSThe authors wish to acknowledge the assistance of R. F. Fisher, who made the roasting and magnetic tests."

Mar 1, 1942

By Peter A. Cain, John C. Folinsbee

"A 4-ft.-diameter shaft has been drilled to a depth of 2,790 ft. in strong, hard, basic Precambrian rocks at Lynn Lake Manitoba. This was done on the property of Sherritt Gordon Mines Limited for the purpose of ventilating and developing the ""N"" orebody, which is located approximately 4,000 ft. south of the Farley shaft.The drilling was done under contract by two drilling companies. Peter Bawden Drilling (1964) Limited drilled the initial 12:1,4-in. pilot hole to a depth of 3,000 ft. Shaft Drillers Limited of Canada then reamed the hole to 4 ft. in diameter to a depth of 2,790 ft. At this point, the reaming was stopped because of the difficulty in passing a change in direction in the line of the pilot hole. The hole was completed by driving a raise 200 ft. from the 3000 level to the bottom of the 4-ft. hole using an Alimak raise climber.Cuttings from the reaming operation were directed into the 12:1,4-in. pilot hole, where they fell to the 3000 level and were removed by a mucking machine and standard mine development cars.The elapsed time from the start of the pilot hole to the completion of the reaming operation was ten months, with an average advance of 279ft. per month. There was a two-month delay between the completion of the pilot hole and the start of the reaming operation.The 12:1,4-in. hole was drilled in an elapsed time of 45 days from the time of setting up the rig. The average advance per day was 66.8 ft.The reaming operation was done in an elapsed time of 194 days. A one-month delay required to repair damaged equipment left 163 days for the drilling and setting-up operation, for an advance per day of 17.1 ft."

Jan 1, 1966