Search Documents

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

By O. Schumacher

Guidelines for publication of information defining the amount and grade of resource material available in a deposit are well established in Australasia?s JORC Guidelines, Canada?s National Instrument 43-101 and similar documents in South Africa, Peru, Chile and elsewhere (Table 1). These guidelines provide standards to apply regarding the geologic and geostatistical basis for describing the level of confidence to be assumed for an estimate of the amount and grade of material. All of them provide for a strict distinction between material that has been demonstrated to be economically mineable and that which has not, and all of them provide terms such as ?resource? or ?exploration information? to be applied to data regarding material that has not been demonstrated to be economically mineable. It is not until an economic study has been completed that we are allowed to apply the powerful terms ?reserves? and ?ore? to our deposit material. Indeed, the application of these eye-catching labels immediately tells the reader that an economic study has been completed by a qualified person, and that the results of the study were positive. While extensive guidelines are established for describing the level of confidence in published geologic data, and the nature of the economic study that should be accomplished before using the terms ?reserves? or ?ore?, surprisingly little guidance is provided regarding the process to use, and the level of detail to attain, for estimating capital and operating costs for the study. The intent of this paper is to lay the groundwork for development of suitable guidelines for the cost estimating process. While the codes do not provide specific instructions for the cost estimate, they do provide numerous hints and clues to help determine the level of detail expected and the type of procedure to apply in preparing the estimate. This paper will first review the various codes to gain an insight into the thinking of the drafters of the codes regarding their unstated expectations for the cost estimating process. Based on this review, a series of guidelines are proposed for this purpose.

Feb 27, 2013

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

In longwall mining, premining prediction of methane emission rate depends on a number of geological factors, geographical factors, and operational factors. These same factors also can impact the selection of a specific degasification system. This study proposes a principle component analysis (PCA) and artificial neural network (ANN) approach to predict the ventilation methane emission rates of U.S. longwall mines and the optimum combination of degasification boreholes based on the given characteristics of the mine. Artificial neural networks, more than conventional computer models, are adaptable systems that can solve problems such as non-polynomial or very complex relationships that are difficult to describe mathematically. Data on ventilation emissions and degasification system design were obtained from 63 longwall mines in 10 states and were combined with corresponding geological, geographical, and operational parameters for the period 1985-2005. PCA was used to determine the variables that most influence ventilation emissions and degasification system design. Different combinations of variables in the data set and network structures were used for network training, cross-validation, and testing. The resultant ANN models predicted ventilation methane emissions with a 90-95% accuracy and were superior to multi-linear and second order non-linear models. The ANN-based expert classification system was able to classify the design of the degasification system (no degasification, gob vent borehole, horizontal and gob vent borehole, and horizontal, vertical and gob vent borehole) with more than 80% accuracy. The models can be used as prediction and decision tools for the ventilation emissions and degasification system selection for specific site and mine-design conditions.

Jan 1, 2009

The concept of æsustainabilityÆ can largely be defined as development that will not compromise the ælivabilityÆ of the planet for future generations. It has multiple dimensions, such as the triple bottom line û environmental, economic and social. And it also includes temporal (now and the future) and spatial (local and global) aspects that have to be taken into consideration to achieve true sustainability.Energy sustainability might be defined as û having the light turn on when you push the switch. It has, of course many more dimensions than this simplistic definition. Coal in Australia has an important role in keeping our lights on, but has its problems that need to be tackled head on to maintain a role in sustainable development.An overriding issue in terms of sustainability for coal is its major contribution to our greenhouse gas emissions. Whilst we have one of the most effective energy sectors in the developed world, based on well-managed, abundant fossil fuels, our greenhouse gas emissions are one of the highest per GDP in the developed world. We have to reduce our ægreenhouse gas signatureÆ.This paper explores the issues of coal utilisation greenhouse gas emissions as an indicator of the fuelÆs sustainability and the potential lower emissions pathways we will have to follow in a future carbon-constrained world.The technology changes will have significant implications for the minerals industry and it is argued that forward-looking coal/greenhouse emissions strategies need to be developed in alliance with the coal (and energy) sector for the minerals industry to maintain its global competitiveness.

Jan 1, 2004

By N. F. Faria, F. Monteiro, B. O. Taiwo, A. Palangio, D. Fonseca, J. Manuel

This paper explores the interpretation and application of Particle Size Distribution (PSD) curves in optimizing blast design and enhancing downstream operations. The study looks at important factors like D50, D80, fines content, and the uniformity index to show how PSD curves affect the efficiency of different mining processes. The first section of this paper discusses the impact of blast design parameters such as burden, spacing, and explosive energy on the resulting PSD, highlighting their significance for downstream operations like crushing, and material handling. The section concluded that proper alignment of PSD with downstream size classes, like primary crusher inlet sizes, among others, can result in substantial cost reductions and productivity gains. The second part presents a case study from dstgroup aggregate quarry in northern Portugal, utilizing fragmentation analysis to evaluate blast performance and promote continuous improvement. The section specifically examines the effect of stemming material size on blast fragmentation, comparing the impact of using aggregate with a D80 of 12.32 mm versus a D80 of 21.94 mm. The D80 value represents the particle size at which 80% of the stemming material is smaller, making it a critical parameter in evaluating the stemming's effectiveness in confining explosive energy. The drilling and blasting designs were meticulously planned using O-PitDev and O-PitSurface software to ensure accuracy in blast parameters and layout. To assess the fragmentation resulting from these different stemming material sizes, the study utilized WipFrag 4 software. The software allowed for precise measurement of particle size distribution after the blast, as well as a detailed comparison between the two stemming sizes. Results from the analysis indicate that using bigger-sized stemming material led to improved blast confinement, which in turn resulted in better fragmentation compared to the smaller-sized material. The reviewed blast videos demonstrate that the larger aggregate effectively contained the explosive energy within the borehole, thereby reducing premature venting and directing more energy towards breaking the surrounding rock mass. This led to finer fragmentation with D80 = 1240.1 mm, D50 = 685.9, and Dmax = 2580 mm, which is advantageous in downstream operations like crushing and milling. On the other hand, the smaller stemming material (D80 = 21.94 mm) did not confine the explosive energy as efficiently, resulting in coarser fragmentation (D80 = 1327.37 mm, D50 = 750.76, and Dmax = 2370 mm) and reduced overall blast efficiency. These findings highlight the significant influence of stemming material size on blast performance and fragmentation outcomes. 

May 4, 2025

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

By P. F. Allen

WITH capacity of 51,000 tpd, the Morenci concentrator produces approximately 49,000 tons of tailing for final deposition. Disposal involves distribution of thickened tailing to dams in such a manner that solids can be used for dam construction and water can be impounded for reclamation. During early operation, although tonnage treated was lower, it was necessary to use orthodox disposal practices in the areas available for tailing. Trestles mounted on a series of dams, constructed of borrow material, carried the pipelines from which tailing were spigoted behind the dams. When adequate disposal areas were finally established, it became desirable to look for more efficient methods. The idea of placing the distribution pipe or manifold directly on the crest of the dam was advanced in 1945. After a period of testing, that procedure in modified form replaced the older trestle arrangement. Marked economies resulted, and time required to prepare dams for succeeding storage cycles was greatly reduced. The tailing disposal area for the Morenci concentrator lies south and southwest of the concentrator building. Ample storage space is available. A wide valley contains three sharply defined ravines lying on an average slope of 4 pct. The more central of these ravines, and the largest of the three, is known as Morenci canyon, which provides substantially more tailing storage area than the other two. Stargo canyon lies to the west; the other is appropriately named East canyon. Total area of the tailing disposal site is nearly 31/4 sq miles, or about 2000 acres. The storage area in use was somewhat more than 850 acres at the end of 1954, or 16 acres per 1000 tons of tailing to be stored daily. At the present time none of the east side dams are in regular use but they are available in emergency. There are five dams on the west side (in Morenci and Stargo canyons) as well as two auxiliary dams adjacent to No. 4 West and No. 5 West. This has made it possible to concentrate men and equipment in a smaller area with consequent savings in both manpower and machinery. Tailing Thickening: Tailing from the flotation process reaches the thickeners with a solid content of about 18 pct. The launder carrying this pulp is subdivided at a central point into seven launders carrying a proportional share to each of seven tailing thickeners, which are located in Morenci canyon close to the concentrator. Five of these thickeners are 300 ft diam and two are 325 ft diam. Thickeners are of the peripheral traction type and rakes travel at the rate of one revolution in 37 to 39 min. The entire installation provides 500,000 sq ft of settling area, or approximately 101/2 sq ft per ton of tailing to be thickened daily.

Jan 1, 1957

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By K. Galovich, P. Krivokuca

"Quinsam coal mine is located about 25 km west of Campbell River on the east coast of Vancouver Island, British Columbia. Using continuous miners in a fully mechanized retreat room-and-pillar operation, it produces low sulphur, “super compliance” thermal coal for domestic and international markets at a rate of about 2600 t/d. Currently, 65 people work at the site, including some corporate employees.Opened in 1993, the Quinsam mine had a dismal safety record until 1997. Lost time injuries and medical aids were unacceptably high. In 1998, a change in corporate structure brought a change in safety attitudes; a total and unequivocal commitment to safety as job No.1 by corporate and site management. This commitment was clearly spelled out in a new mission statement, circulated to all employees by the new President and CEO, David Slater: “Safety is job No. 1; Production flows from safety; and Think safety at all times.” As well as re-defining workplace safety practices, QCC tightened engineering controls and enforced strict adherence to mine plans.This paper provides a general background to the mining operation, and describes the safety practices that have resulted in an enviable safety record in recent years, reflected by provincial and national recognition."

Jan 1, 2004

By Christoph Zschiesche

Managing complex material streams within a lead smelting/reduction process has a long history at Aurubis. After modernization of the secondary lead smelter in 1991, Aurubis operates an electric furnace and a Peirce Smith converter to process complex secondary materials. This process links the copper and the lead metallurgy allowing Aurubis to properly combine primary and secondary process lines to optimize the processing of complex raw materials and smelter intermediates. However, combination of copper and lead metallurgy processing requires a continuous evaluation as raw material quality and composition varies. This paper describes Aurubis lead smelter processing and provides some fundamental considerations to optimize the lead processing, in particular with aspects related to speiss formation

By Fabio do Prado Verderano

A partir de corpos de prova de uma chapa de aço baixa liga NBR 6656 grau LNE 26, realizou-se a caracterização microestrutural, levantamento do perfil de dureza ao longo da espessura da chapa, ensaios de tração monotônicos, cíclicos de fadiga e análises fractográficas. Concluiu-se que, nas extremidades da espessura da amostra, o valor da dureza é maior, indicando que quando a chapa foi laminada as superfícies em contato com os rolos de laminação sofreram encruamento, aumentando a dureza nessa região. A microestrutura encontrada e o grau das inclusões presentes na amostra são compatíveis para o material, bem como as propriedades mecânicas monotônicas, que estão de acordo com a especificação. Por meio de ensaios de fadiga de baixo ciclo, encontrou-se uma boa correlação entre as propriedades monotônicas e cíclicas do material para a proposição da equação de Basquin, considerando-se dados seguros, quando utilizado os primeiros vinte ciclos do ensaio de fadiga para estabilização de cada corpo de prova. Verificando-se a seção transversal da fratura do corpo de prova, observa-se que o mecanismo de falha do material ocorreu a partir do aparecimento de trincas na interface ferrita-cementita com propagação transgranular até a fratura final.

Aug 17, 2017

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

Caving of the second lift of the E26 orebody at Northparkes Mines was monitored with a comprehensive package of instrumentation, including an ISS seismic monitoring system. Seismicity was collected by an array of 19 triaxial accelerometers and 9 uniaxial geophones, giving a high quality seismic data set. The seismic response to block caving at Northparkes has been divided into two papers. The first paper focuses on the seismicity during undercutting. The second paper deals primarily with the seismicity during cave propagation during initial cave production. In this paper, traditional seismic monitoring concepts are applied to seismicity during cave mining. More than 40 000 seismic events were recorded during cave undercutting between February and January 2004. Events up to local magnitude +1.3 were recorded near the mine during undercutting, with event rates of up to 500 per day. Analysis of frequency-magnitude distributions, S-wave to P-wave energy, and temporal variations in event magnitude all gave insight into the seismicity recorded. In addition, a new technique, called apparent stress time history, was shown to be sensitive to stress change from undercut blasting, and useful to identify significant periods during cave development. A significant difference was identified between the cave back location and the halo of seismic events above the cave. Throughout the undercutting, the a seismic zone of loosening was typically 50 to 70 metres in vertical thickness. Based on the seismicity, a stress driven rock mass failure model is proposed. Early in the undercutting, seismicity and movements in the seismogenic zone were directly triggered by stress change from undercutting. Towards the end of undercutting, seismicity was virtually uncorrelated with undercut blasting, and likely due to the onset of cave initiation.

Jan 1, 2008

By N. J. Castilla, R. Giglio

"Circulating fluidized-bed (CFB) combustion technology has been around for over 40 years, but over the last 6 years it has been commercially demonstrated at the 500 MWe scale at the Lagisza plant located in Bedzin, Poland. The CFB at the Lagisza plant has unique first-of-a-kind design features, such as vertical-tube supercritical steam technology and a lowtemperature flue-gas heat extraction that allows the plant to achieve high plant efficiencies of over 43% (net lower heating value). Another unusual feature for a coal power plant is that this plant meets all its atmospheric emission permit levels without any post-combustion de-NOx or de-SOx equipment such as selective catalytic reduction (SCR) or flue-gas desulphurization (FGD).CFB clean coal power technology is entering the utility power sector just in time to help deal with declining quality in internationally traded coals and to promote the large-scale use of economic, low-quality domestic fuels. Owing to the very attractive price discounts, growing supplies of low-quality Indonesian coals are outpacing the supply of high-quality Australian, Russian, and US coals. In Germany and Turkey, the use of domestic lignites for power production provides a secure and economic energy solution while creating domestic jobs.Conventional pulverized coal (PC) boilers will have trouble accepting these off-specification coals because of their narrow fuel specifications; they typically call for heating values above 5500 kcal/kg. This limitation is not an issue for CFB technology because of its ability to burn the worst and best of coals with heating values ranging from 3900 to 8000 kcal/kg.This paper provides an outlook for future coal supply, quality, and price, as well as a review of the technical and economic benefits of CFB technology firing low-quality fuels for utility power generation."

Jan 1, 2015

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006

CONTENTS RUSSIA-R. C.-BECKSTROM 3 VENEZUELA-F. H. KAY 9 TRINIDAD-W. J. MlLLARD 20 RUMANIA-1. I. GARDESCU 26

Jan 1, 1932

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By P Wigley

New methods of analysing and modelling flotation circuits have been developed as part of the AMIRA P9 mineral processing research project. A study using these techniques was conducted on the Olympic Dam copper flotation circuit to provide the following outcomes: an estimate of the flotation cell hydrodynamic properties and froth performance characteristics, and identification of potential areas for improvement; an estimate of the feed floatability parameters for basic model development; and identification of potential flotation circuit improvement opportunities. A flotation circuit model of the Olympic Dam copper concentrator was developed using the data collected from mass balanced site surveys, along with hydrodynamic data, froth performance data and numerous laboratory batch flotation tests. The simulator that has been developed from the model has the ability to estimate the influence of selected changes (such as circuit changes) on flotation circuit performance. Several stream destination simulations were conducted to provide guidance for further testwork and possible circuit improvements. The results from these simulations are presented.

Jan 1, 2003