Search Documents

By S. Banisi, A. Haji-Zadeh, H. Asadi, M. Maleki-Moghaddam

One area in AG/SAG milling field which has received a great attention is the optimization of liner design for any application to increase the availability of mills. The Gol-E-Gohar iron ore concentration plant uses three 9m × 2.05m autogenous mills (AG) in parallel in a dry operation. The AG mill shell is lined with three series (57 cm each) of 36-row liners. Due to large variations in feed characteristics and inadequate blending, the performance of AG mills has been lower than the target value. Therefore, to improve the comminution efficiency, the optimization of the design of AG mill shell liners was applied in this plant. By simulation it was found that increasing the liner lifter face angle from 7 to 30° while maintaining the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. Measurement of the wear profiles of shell liners indicated that the wear along the liner length was not uniform and the highest wear occurred between 0.5 m and 1.2 m of the mill length. A new liner design was proposed by redistributing the metal from parts with a lower wear rate to the parts with a higher wear rate to arrive at a uniform wear profile along the liner length at the liner removal time. The non-uniform shell liner was constructed and installed in one of the three parallel dry AG mills. It was found that the first and second liner designs increased the mill throughput by 2.6 and 7.5%, respectively. After conversion to SAG milling on the account of liner change, 18% (from 413 to 489 t/h) increase in throughput was realized. It was predicted that the non-uniform liner designs will increase the liner life time by 10% and will reduce the scrap metal from the current value of 59% to 50%.

Jan 1, 2014

By C. A. Young

The remediation of cyanide (CN-) and nitrate (NO)-) anions in mine and agricultural waters by various photolytic methods has been reviewed and investigated. Photolytic methods such as direct photolysis, homogenous photolysis, and heterogeneous photocatalysis are briefly described and compared. Results and discussions show that each method has certain advantages and disadvantages. For each method, Eh-pH diagrams prove useful for determining reaction mechanisms. Preliminary results obtained for cyanide oxidation and nitrate reduction show that homogeneous photolysis can be superior due to faster kinetics than the other methods. The photolytic methods were individually, not simultaneously, tested and compared. Differences in concentrations of products were obtained and attributed to differences in photoconversion efficiencies and other inherent characteristics of .the photolytic methods. Various reaction mechanisms are proposed in accordance with the literature as well as measurements obtained from solution analysis using ion selective electrodes and ion chromatography .

Jan 1, 1995

In 1953, Dr. N. H. Fisher of the Bureau of Mineral Resources, acting on behalf of the Society of Economic Geologists, which is considering the sponsoring of a uniform system of nomenclature for ore reserves, enquired from the Australasian Institute of Mining and Metallurgy whether it had ever considered this subject and particularly whether it had ever set up any standard definitions or specifications with regard to ore reserves.As this had not been done, but was thought to be desirable, the Council of the Institute appointed a Committee consisting of H. H. Dunkin, Associate, Professor of Mining Engineering, University of Melbourne (Convenor), E. A. Rudd, Professor of Economic Geology, University of Adelaide, I. N. Campbell, Chief Geologist of Western Mining Corporation; and the writer to consider and report on this supject.In December 1953, the Committee submitted its first report to the council and this report (reproduced here as an Appendix) was widely circulated among member companies, and engineers, with an invitation to comment on the proposal. A large number of, replies was received and studied.After studying the replies the Committee issued a second report in part as follows:-From these replies we have learned that the suggestions made in the first teport of the Committee are unacceptable to most of those interested, on one or all, of the following grounds;-(a) number of categories,(b) definition of categories;(c) nomenclature.

Jan 1, 1955

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

The production of metallic titanium and titanium-rich alloys in forms useful to the engineer involves the use of certain techniques not usually necessary in fabricating the commoner metals and alloys. However, not all stages in the handling and shaping of titanium-base materials require the application of unfamiliar methods. It is the purpose of this paper to indicate where the well-known techniques are applicable as well as to outline the unusual operations which are necessitated by certain chemical characteristics of titanium.In brief, the characteristics just mentioned are manifestations of the very great reactivity of titanium, especially at elevated temperatures. Liquid titanium burns vigorously when brought into contact with air. It also reacts with practically all refractories, causing damage to the latter as well as undesirable contamination of the metal. Even solid titanium undergoes serious superficial contamination when heated above 800°C. in air for more than a few minutes. In addition to an oxide skin being formed, oxygen enters into solid solution in the surface of the metal causing the latter to become hardened and eventually embrittled.Up to date, titanium has been made only on a pilot plant scale by methods which produce a spongy or powdered product. Refractory problems have prevented the development of chemical reduction methods for making titanium in the form of a liquid pool from which ingots of useful size could be cast. Therefore the first part of this paper will cover the consolidation of powdered or spongy titanium. The latter portion will provide a brief description of...

Jan 1, 1950

By A. J. Potgieter, C. Hill, A. Humpel, D. S. Magudulela, V. Scholtz, A. Coetzee

Keywords: Pyrometallurgy, long steel products, coke, sinter, blast furnace, steel plant Located in Northern KwaZulu Natal, Mittal Steel South Africa Newcastle works produces roughly 1.8 million tons per annum, supplying long steel products, locally and overseas. The great extent of local raw material availability and low conversion cost ensures that Mittal Steel South Africa is among the lowest cost, high quality producers of steel. MSSA Newcastle works can be subdivided into two main sections: The iron making side, comprising the coke ovens, sinter plant and blast furnace, and the steel making side, comprising the basic oxygen furnace, ladle furnace, continuous casters, and the medium, rod, and bar mills.

Jan 1, 2006

By Kun Wang, Xinhui Li, Huaqing Xie, Qingbo Yu, Qin Qin

"Three typical model compounds of bio-oil (ethanol, acetone and phenol) were studied in the steam reforming process for hydrogen production. In the thermodynamic analysis, the three componds showed the similar trends. The hydrogen yields increased with the increase of steam/carbon (S/C) ratios, and the temperatures of the maximum hydrogen yields moved afterward to low temperature zone. However, the hydrogen contents were just about 70%. For improving hydrogen yield, a new system for steam reforming of bio-oil with site CO2 capture was put forward. This system required the catalst with the larger granularity having greater mechanical strength and higher abrasion resistance. So, six Ni-base catalysts loaded on Al2O3 particles prepared were used and among them, Mg-Ni/Co catalyst showed the best catalytic performance. For the simulated bio-oil (the mixture of the compounds), the hydrogen yield can attain 63% with Mg-Ni/Co catalyst with the good stability and regeneration ability.IntroductionCurrently the interest in the use of hydrogen as a clean energy carrier is increasing, and the main way for producing hydrogen is steam reforming of fossil fuels, containing steam reforming of nature gas, naphtha and coal. But this way caused substantial amounts of CO2 emitted, and these sources of hydrogen which are non-renewable energy will eventually be used up [1, 2]. As a kind of renewable energy, biomass is recognized as an attractive alternative to fossil fuels, because of its neutral CO2 emissions [3]. There are mainly two thermochemical processes using biomass to produce hydrogen, gasification and flash pyrolysis followed by steam reforming (SR) of the biooil produced in the flash pryolysis process [4]. The latter was known as one of the most promising and economically viable methods for hydrogen production [5]. In the last decades, the biomass flash pyrolysis technology was adequately developed and fairly mature [6]. But the steam reforming of bio-oil is still at the research stage and yet has been leading to more and more concerns by the researchers. In their research, the catalysts were widely studied and yet mainly were powdery[7-10], and the reactors manily were fixed bed reactors[11-13], readly causing the carbon deposition and the catalyst deactivation, against the continuous running. In this paper, a new systerm was put forward and could realize continuous production of hydrogen, yet needed catalysts with the larger granularity having greater mechanical strength and higher abrasion resistance, as well as powdery CO2 sorbents which mainly calcium oxide based ones.In this paper, the thermodynamic analysis of the steam reforming processes of three typical bio-oil model compounds (ethanol, acetone, phenol) was performed, and the effect of S/C ratio and temperature on the hydrogen yield and the compositions of gaseous products were investigated. Then, a new systerm for steam reforming of bio-oil with site CO2 capture was put forward, and the catalysts with a certain granularity were prepared and studied."

Jan 1, 2014

By D. S. Pye, J. P. Gallus

Successful hydraulic pressure treatment of oil and gas wells that have long producing intervals, multiple pay zones, fluid thief zones, or natural or induced fractures has long been a serious problem plaguing the petroleum industry. High fluid-injection rates, straddle packers, ball sealers, and either liquid or solid additives to the treating fluids are being used to cope with this difficult and costly problem.l-6 The use of ball sealers and straddle packers is limited, in practice, to wells that have been completed with perforated cemented casings or liners. Well stimulation with ball sealers and straddle packers is usually successful as long as the cement remains competent. The other techniques of diverting are used with all types of completions. However, there are two significant disadvantages of the high rate method: excessive horsepower requirements, and the need of large treating-fluid volume. Consequently, most well stimulation techniques that involve diverting depend upon ball sealers or granular materials. Liquid diverting agents, and some of the solid ones in use today, frequently will cause formation damage. On the other hand, the most popular particulate diverting agents often are so soluble in the treating fluid that they become largely ineffective; their particle size is severely reduced as they dissolve while being transported through thousands of feet of pipe to the formation face down hole. In our attempts to deal with the shortcomings of these diverting agents, we experimented with a large variety of potentially suitable deformable materials the solubility of which could be controlled. Following are the criteria for the diverting agent sought: 1. The material must be effective in reducing fluid loss to thief zones, including existing fractures and very high permeability layers in the formation to be pressure treated. 2. The material must have enough strength to bridge under the treating pressure. 3. The material must be insoluble or slowly soluble in the treating fluids so that the particles retain sufficient size to be effective after they reach the formation face. 4. The material must be completely soluble in the produced oil or condensate liquid so that it can be removed readily; it must not cause formation damage. A number of products consisting of various polymers blended with waxes and other solid hydrocarbons were examined. All these materials satisfied the criteria for a diverting agent and also exhibited some degree of plastic deformability. On the basis of initial tests of strength and hardness, several blends of wax and polymer were selected for extensive testing in the laboratory and the field. These compounds have congealing temperatures ranging from 140 to 190F; they are insoluble in water and soluble in oil. They conformed, therefore, to the criteria specified for a theoretically superior diverting agent. Laboratory and field tests were conducted using these wax-polymer materials to demonstrate that the use of a deformable diverting agent can significantly improve fluid diverting performance. Data in this

Jan 1, 1970

This investigation was planned to determine:1. The precipitation-hardening properties of the copper-nickel-phosphorus alloys; and2. The influence of arsenic and bismuth, singly and together, on the mechanical properties of these alloys.It was carried out in conjunction with an investigation, previously published in these Prooeedings on "The Influence of Various Elements on the Mechanical Properties of Copper containing a small percentage of Bismuth," and also formed part of a study of the influence of bismuth, nickel and phosphorus on the properties of commercial arsenical-copper.The first part of the present investigation arose out of a discovery some years ago of precipitation-hardening in phosphorus-deoxidized coppernickel boiler tubes, containing approximately 2% nickel and 0·03% phosphorus, supplied to an Australian Railways Department. At that time there was little information available on precipitation-hardening in copperrich copper-nickel-phosphorus alloys, but at the end of 1935 a short paper on the subject was published by E. C. Rollason and T. G. Bamford(2) and at the beginning of 1940 a comprehensive account was published by D. K. Crampton, H. L. Burghoff and J. T. Stacy.(3) Although the investigation carried, out independently by the present author was not as comprehensive as that of Crampton, Burghoff and Stacy, the results are in agreement with those of the American as well as of the British authors; hence, only a summary of this aspect of the work is needed here to establish a basis for a study of the influence of bismuth and arsenic.PREPARATION OF TEST PIECESAll alloys were melted under charcoal in plumbago crucibles in an oil-fired furnace and were poured out of contact with air into oil-dressed moulds to give billets either 7· 5 in. long X 0.83 in. diam. X 1·3 lb. weight or 12 in. long X 1·125 in. diam. X 3·3 lb. weight depending on requirements (the larger size was used, for example, in establishing the annealing characteristics of the precipitation-hardening alloys). The raw materials were electrolytic copper of the composition described in the previous paper(I) 6% copper-arsenic, 14% copper-phosphorus, 1:7% copper-bismuth, and Mond nickel in the form of "shot." The method of producing test pieces from these billets and the annealing treatments ana tests to which the pieces were subjected have been described in the previous paper.

Jan 1, 1944

By P L. McCarthy

To design and operate a successful mine the technical specialists must agree on what is ore, what is not ore, and how quickly the orebody is to be mined and processed. These seemingly simple questions defy easy analysis and can push mining engineers, geologists, metallurgists and others to the limit of their capabilities. The questions are rarely addressed adequately in feasibility studies or in operational planning. To optimise the mine and processing plant requires proper determination of cut-off grades or values, prediction of feed variability on an hourly, daily or longer basis, right-sizing the mining rate for optimum product quality, understanding the cost of capital and the expectations of investors, and many other considerations that involve geology, geotechnical engineering, mining, metallurgy, environmental effects and economics. This paper addresses the key matters that should be considered as inputs to the practical issues of metallurgical plant design and operation.CITATION:McCarthy, P L, 2015. Integrated mining and metallurgical planning and operation, in Proceedings MetPlant 2015, pp 35–45 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Winzes are usually sunk 9 ft. 6 in. long by 6 ft. 0 in. wide and are divided into two compartments, 4 ft. 0 in. by 5 ft. 0 in. inside the timbers. The general practice is to sink the winze to a depth of from 9 to 12 ft., put in bearers and three or four rings of timber, and then erect a sinking headframe before continuing sinking operations.GENERALThe main feature governing the design of the headframe was that all parts could be transported on timber trolleys in No. 2 Shaft. Except for some minor details the structural members consist of steam pipe. Joints are sections of steam pipe welded to one member and into which the other member fits and is held in place by a 1-in. bolt. The headframe consists essentially of two bedpieces to carry the winch and to form a seat for the four legs. The legs support the sheave bearers, the tipping door and the brace.Except during tipping operations the door is in a nearly vertical position. For tipping it is lowered to an inclined position and a hook suspended from one of the bracing members of the headframe is attached to a "D" welded to the bottom of the kibble. This causes the kibble to tip when it is lowered on to the tipping door. The capacity of the kibble is 4 cubic feet.THE HEADFRAMEThe dimensions of the headframe are:Height to top of sheave .. .. 14 ft. 10 in.Distance centre to centre of legs 4 ft. 4 in.Length of bedpieces .. .. .. .. 8 ft. 9 in.The weight is approximately 2,000 lb., the tipping door and bedpieces being the heaviest members. They weigh 240 lb. and 170 lb. respectively.One compartment of the winze is decked over, and the bedpieces, which are 8 ft. 9 in. lengths of 6 in. pipe with three short lengths of plate welded to the underside, are placed over the sinking compartment, either transversely or parallel to the winze. Three 3 inch pipes act as spreaders between them.Welded to the top of each bedpiece is a 6-in. by iHn. plate 3 ft. 0 in. long with four 4-in. by 1.5-in. slots cut longitudinally at 10 in. centres. Two 10 in. by 4-in. timbers are bolted to these plates, the distance between them being adjusted to suit the holes in the winch bedplate, which is bolted to the 10-in. by 4-in. timbers.Two short lengths of 3 in. pipe are welded to each bedpiece at 4 ft. 4 in. centres. These form the seats for the legs of the headframe, which are...

Jan 1, 1941

By A. T. Robles, L. Buckingham

"When certain gold ores containing pyrite, graphite, humates and fumates or other organic compounds which are possibly adsorbed on clay minerals are treated with aqueous solution of alkali metal cyanide, the aurocyanide complex which forms is adsorbed by these ""pregrobbing"" species in the ore. Dissolution of gold proceeds until chemical equilibrium is attained between the cyanide complex adsorbed by the ore and in solution.Sodium lauryl sulfate (SLS) may be used to decrease the adsorptive activity of the prerobbing species in the ore. It has successfully improved recovery at Holt-McDermott Mine and is highly biodegradable.INTRODUCTION Precious metal-bearing ores containing preg-robbing species are poorly amenable to standard cyanidation techniques. The ""preg-robbing"" impurities with which they are associated tend to adsorb the gold cyanide complexes and carry them through the circuit to the tailings. Also, gold may be associated with these impurities in the ore and not be leached by the cyanide complexing agents used in conventional cyanidation techniques.Methods for dealing with the problem of preg-robbinq impurities in gold ores are:Carbon-in-Leach (CIL), in which granular activated carbon is added to compete with preg-robbing species for the gold cyanide complexes. This process can improve gold recovery in mildly preg-robbing ores especially when fine carbons with very high activities are used. However, with severely graphitic ore, the carbon associated with the rock may outperform the granular activated charcoal.Chemical Oxidation, in which the ore is subjected to preliminary chemical oxidation techniques to oxidize carbonaceous materials using such diverse reagents including ozone, sodium hypochlorite, calcium hypochlorite, chlorine gas, permanganates, perchlorates, chlorates and oxygen prior to subjecting the oxidized ore to standard cyanidation treatment to extract gold. This is generally a costly method and will not prove economical on a low-grade ore."

Jan 1, 1992

Geochemical projects in progress or recently completed in the Bureau of Mineral Resources, Geology, and Geophysics (BMR) cover a wide range of topics and include research projects, regional studies, and prospecting programmes. However, in these notes emphasis is given to projects which are directly relevant to mineral exploration.FIELD INVESTIGATIONSStream sediment sampling, rock and soil sampling, and geobotanical surveys have been used by the BMR in a number of areas, partly in attempts to locate specific zones of mineralization, and partly to investigate the effectiveness of the various methods under different conditions of climate and topopraphy and in different geological settings.Stream sediment sampling has been most successful in the Territory of Papua and New Guinea. For example, in the South Sepik area, zones of disseminated su1phide mineralisation were found to give rise to anomalies with peak values of up to 1,000 p.p.m. copper, compared with background values of about 40 p.p.m. (Dow et al., 1968). By contrast, the results of rather limited work in the Northern Territory and in the Kimberley district of Westen Australia were inconclusive.Rock and soil sampling, on the other hand, was successfully used in a number of areas in Northern Australia, particularly at Rum Jungle and Tennant Creek.Rum Jungle area In the Rum Jungle area, where uranium and base metal mineralization is mainly associated with a Lower Proterozoic black slate sequence, samples, of c-horizon soil or weathered 'rock are generally collectedfrom the bottom of drill holes, usually 15 to 20 ft deep, bored with a power-operated auger.Surface sampling indicates that such a technique would probably have shown up all the major geochemical anomalies delineated by deep sampling, but the latter gives slightly more consistent and slightly

Jan 1, 1970

By Dean Brox

The use of Tunnel Boring Machines (TBMs) for tunnel construction of long tunnels in the Andes of South America has been of mixed success in the past due to a variety of reasons and key lessons can be recognized. A review of past TBM tunnel projects in the Andes has unveiled some interesting findings for different TBM tunnel approaches with both world records of progress as well as nearly in-completed projects with machines being abandoned. Key considerations for the use of TBMs for tunnel construction in the Andes include geological issues; (faults, rock type, rock strength, rock abrasivity, durability, groundwater inflows),depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, intermediate access possibilities, minimum tunnel size, support requirements, contractor and labour experience, and project schedule demands. TBMs offer highly recognized schedule benefits(high progress, no concrete lining) for a project if intermediate access adits are limited as well as hydraulic benefits for water conveyance projects. Minimum specifications for TBMs can be easily developed to suit the unique requirements of any project so as long as all factors are carefully considered. The overall conditions and factors associated with some projects may suggest that it is not appropriate to use TBMs due to a perceived high risk. Finally, access for geotechnical investigations by drilling in the commonly steep terrain of the Andes is typically difficult and often not impossible. Alternative approaches for geotechnical investigations for TBM tunnels including comprehensive mapping, high-resolution airborne electric-magnetics for delineation of possible fault zones, and rock block sampling is presented and discussed.

By D Johnston

Within the first full year of BarrickÆs Cowal Gold Mine operation, the Lake Cowal Foundation Limited (LCF) has already been delivering results consistent with its goal to protect and enhance the natural environment of Lake Cowal and its catchment area. The LCF is a non-profit Environmental Trust established in June 2000 in conjunction with the development consent process for the construction of BarrickÆs Cowal Gold Mine. Its primary goal is to protect and enhance Lake Cowal, a nationally significant ephemeral wetland located 350 km west of Sydney, New South Wales, Australia. Significant concentrations of water birds visit the lake and the Australian Heritage Commission listed Lake Cowal on the Register of the National Estate in 1992. The LCF is managed by a Board of Directors from representative member organisations including the Total Environment Centre, National Parks Association, Nature Conservation Council and Barrick Australia Limited. Although largely funded by Barrick, the Foundation also attracts external funding and works in partnership with a diverse range of other groups and organisations, beyond the mine fence. The total value of currently approved projects is estimated to be in excess of $7.1 million, which includes æin-kindÆ contributions made by the local community and in particular the Lachlan Catchment Management Authority (LCMA) and local farmers. To date, LCF has been involved with the development and implementation of 30 projects with a total of 34 project partners. LCF has worked with over 60 landholders to improve Lake Cowal and its catchment, with 6180 ha of land now being managed for conservation or sustainable farming in the local area. Many landholders have been, or are involved in property planning or participating in other training opportunities. Sustainability of LCF programs and outcomes will be assured by commitments to projects within four key themes: conservation, research and research support, sustainable farming and community education and training. The LCF works independently from the mining company and has no responsibility for the environmental management within the mining lease. It is about capitalising resources generated by the mine to enhance environmental outcomes in the wider Lake Cowal catchment area by working collaboratively with the local community, industry and government authorities to ensure the long-term protection of a unique wetland ecosystem affected by landscape scale degradation.

Jan 1, 2007

By J Canterford

There is an apparent push to develop and commercialise "new and innovative" process flow sheets. A not-too-difficult reality check clearly demonstrates that the success rate of this push is not particularly significant and in fact could be regarded as a waste or misappropriation of R&D funding and the associated brain power. As Julian Sumner Miller would comment "why is this so?" To put it bluntly, many of the so-called innovative developments are equivalent to gold plating the dunny door - visually interesting but of very limited practical value. This presentation encapsulates some personal lessons learnt over the past 45 years.CITATION:Canterford, J, 2013. Developing a ænew and innovativeÆ process flow sheet - Traps for all players of all ages, in Proceedings MetPlant 2013 , pp 1-5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By R. Lestari

Newmont Batu Hijau operates with an accelerated mining rate to optimize life of mine (LOM) project economics. This results in a portion of ore mined being stockpiled for reclaim and processing throughout, and at the end of mine life. LOM economics can be further enhanced by preserving stockpiled ore value by mitigating oxidation effects. A detailed stockpile ore oxidation study was conducted to: ?? Develop a practical understanding of how oxidation affects ore value; ?? Determine how oxidation rate can be controlled, and; ?? Determine how oxidation effects can be mitigated to preserve ore value. The result of the study is a stockpile management strategy that significantly reduces oxidation related losses and, implementation of that strategy within practical constraints. Implementation includes installation of Controlled Potential Sulfidisation (CPS) flotation to facilitate oxidised sulfide copper recovery and, recovery of dissolved copper from stockpile drainage solution into saleable product. This paper describes the study results including managing and predicting stockpile oxidation with time, monitoring performance of implemented CPS flotation and recovery of dissolved copper from stockpile drainage. These are essential elements of successful long term mine operation in Batu Hijau.

Jan 1, 2014

By H. D. Kline

This publication describes mining and milling methods and costs at the Madison mine of National Lead Co., St. Louis Smelting & Refining Division, in the Fredericktown district of southeast Missouri and is one of a series prepared by the Federal Bureau of Mines on methods, practices, and costs of mining and milling throughout the United States. The are bodies of the Madison mine are known for the complexity and diversity of their are minerals. Sulfides of copper, nickel, and cobalt occur in commercial quantities with lead sulfide, which is the most valuable metallic mineral in are bodies of the Bonne Terre formation in southeast Missouri. Several attempts were made by various operators to mine the complex ores and separate the sulfide minerals before 1927 when National Lead Co. became interested in the Fredericktown district. Operating then as the St. Louis Smelting & Refining Co., the company began mining and milling ores from the Madison mine in 1944 and has operated continuously since then. A recently built refinery produces copper, nickel, and cobalt metal from a concentrate containing iron sulphides and small quantities of copper, nickel, and cobalt sulphides.

Jan 1, 1961

The Golden Grove Project area is located 220 km (137 miles) east of Geraldton in Western Australia (Fig. 1). The project is a joint venture involving Amax Exploration (Australia) Inc. (Amax), Electrolytic Zinc Co. of Australasia Ltd. (EZ), and Esso Exploration & Production Australia Inc. (Esso), each with 31 116% interest, and Aztec Exploration Pty., Ltd. (Aztec), with a 3 1/2% carried and a 3% contributing interest. The venture covers two significant volcanogenic massive sulfide deposits and some 40 km (25 miles) of highly prospective Archean volcanics. During the course of the past 12 years (to 1983), all four companies were responsible for operating the project at one time or another and all influenced the discoveries. The Gossan Hill and Scuddles deposits are typical examples of volcanogenic massive sulfide deposits associated with Archean explosive submarine acid to intermediate volcanic complexes. They are located in the northwesterly trending Yalgoo greenstone belt of the West Australian Archean Shield. Gossan Hill, located in 1972, is essentially a copper deposit with minor zinc lenses; to date, 97 diamond holes have delineated a geological resource* estimated to contain 13 Mt (14.3 million st) of of 3.4% Cu and 13 g/t (0.38 oz per ton) Ag in the main lenses with minor lenses totaling 2 Mt (2.2 million st) of 3.7% Cu and 17 g/t (0.49 oz per ton) Ag and 1.7 Mt (1.9 million st) grading 1.5% Pb, 14% Zn, and 87 g/t (2.8 oz per ton) Ag. Scuddles is a zinc-copper deposit with gold and silver credits. It *Resource estimate provided by Esso for inclusion in Aztec Exploration Pty. Ltd. 1982 Annual Report was discovered in 1979 and, to the end of 198 1, had been delineated with 42 diamond holes. On the basis of this drilling, a geological resource* of 26 Mt (28.7 million st) has been estimated in three coalescing lenses. The lenses comprise 7.5 Mt (8.3 million st) of 2.1 % Cu, 12 g/t (0.35 oz per ton) Ag, and 0.3 g/t (0.009 oz per ton) Au; 7.6 Mt (8.4 million st) of 0.4% Cu, 9.9% Zn, 73 g/t (2.3 oz per ton) Ag, and 0.7 g/t (0.02 oz per ton) Au; and 1 1.0 Mt (1 2.1 mil lion st) of 1.1 % Cu, 9.3% Zn, 8 1 g/t (2.6 oz per ton) Ag, and 1.5 g/t (0.044 oz per ton) Au. Readers are referred to Frater (1978) and Harris et a). (1982) for a more detailed geological account of these deposits.

Jan 1, 1991

In order to appreciate fully the place of palaeontology within the general framework of the geological sciences, consideration must be given to the time, about 150 years ago, just before the study of fossils was beginning to be applied to geological problems. At theend of the eighteenth century, almost all geologists recognised that fossils were the remains of animals and plants that had lived at the time when the rocks in which they occur were formed. It was also realized that many-some geologists thought all-rocks hadbeen formed under water, but as regards the order of succession in which these rocks had originated, and the relative ages of rocks found in different parts of the world or even of one country, only the haziest and most contradictory ideas existed.Around the turn from the eighteenth to the nineteenth century, a widely taught system of theories was that of the German professor, Abraham Gottlob Werner, who believed that the surface of the earth had once been covered by a universal ocean at whose bottom all rocks had been deposited. As the level of this ocean gradually subsided, older rocks-so Werner taught-are now generally found in the mountains or at great depth below the younger rocks; this was his "Primitive Division" which included granite, gneiss, schists, slates, basalt, porphyry and other igneous and metamorphic rocks, all of which he believed to be of sedimentary origin. Younger rocks, according to Werner, were formed at successively lower levels as the water receded. Next in age he placed a "Transition System" of limestones and greywackes; still younger the so-called "Floetz Division," which included sandstone, limestone, gypsum, salt, coal, but also some basalt, porphyry and other rocks; youngest were the alluvial deposits of recent clays, loams, sands and gravel. Thus, in the Wernerian system the age of a rock was determined on the basis of its petrographic properties and the height of its occurrence relative to sea-level.Here and there these ideas survived well into the nineteenth century. As late as 1825, Charles Darwin listened to lectures by Professor Jamieson, one of the last proponents of Wernerian theories in England. The fact that entirely different kinds of fossils occurredin rocks which were regarded as contemporaneous did not worry the theoreticians.It is, therefore, noteworthy and significant that the value of fossils for the interpretation of geological events was demonstrated to the geologists by an engineer and surveyor, WiIIiam Smith, who, although no professional geologist, has often been called the "Father of English Geology." His professional work, which was mainly concerned with drainage and irrigation projects, took Smith to all parts of England, where he sometimes journeyed as much as 10,000 miles in 11 year. Smith was a keen observer and, unhampered by theoretical speculations, he noted the occurrence of fossils and collected specimens wherever he went. Before long he realized that the same kind of fossils followed each other in successive layers of rocks in much the same way in different parts of England, and soon he was able, by looking at fossils collected by other people, to tell from what...

Jan 1, 1950