Search Documents

On September 4, 2007, Mine Safety and Health Administration, in alliance with the International Union of Operating Engineers and the International Association of Bridge, Structural, Ornamental, and Reinforcing Iron Workers, presented the first annual Mine Construction Maintenance and Repair?s Safety Contractor of the Year Award to Artisan Contracting, Inc., of Cape Girardeau, MO. Eligible contractors located throughout the United States were nominated. Artisan Contracting was nominated by Illinois Cement Company located in LaSalle, IL. Illinois Cement Company is a Division of Eagle Materials Inc., located in Dallas, Texas. Mr. Larry Frankum President of Artisan Contracting Inc., stated, ?While it is gratifying to receive a wonderful award such as this, we must not forget how fragile a good safety record is. We must constantly remain diligent in pursuit of maintaining safe work sites.?

Feb 1, 2008

By Met M, Orr C. W, Met B. E

As was mentioned in the last paper of this series(l), magnesium was added to lead with the idea that it would act as a de-oxidiser. The magnesium lead alloys give rise to an inter-metallic compound of the composition Mg2Pb(2) and it has some remarkable properties. It is known to disintegrate on standing in the atmosphere and it confers this property also on lead alloys in which it occurs. Magnesium forms a solid'solution with lead, and according to Kurnakow, Pogodin' and Vidusova(S) the limits of solubility are as follow...In conformity with the practice used in preceding series, the limit of concentration used in the present investigation was 0.1 %. Accordingly, it would be expected that all the alloys used would consist of the solid solution and the detrimental Mg2Pb would be absent. Whilst this was the case, it...

Jan 1, 1939

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By N. A. D. Parlee, M. M. A. El-Naggar, G. 8. Horsley

The apparatus was of a modified Sieverts type1&apos;2 with a reaction tube designed to function also as the cell component of an oxygen pressure gage. The reaction tube assembly is shown in Fig. 1 and described in Table I. The main body is a 1-in.-OD 15 mol pct calcia-stabilized zirconia tube. The ground-glass joint, g, the male part of which carried a prism for optical pyrometer use, was connected to the remainder of the Sieverts apparatus. The calibration of the cell (at its 1000°K operating temperature) for internal oxygen pressures (PO2in) in the range 0.2 to 10 9 atm was made against internal air pressures measured by mercury manometer and McLeod gage. At very low po2in values down to l<Tn atm the performance was checked by comparing pQ calculated from electromotive force measurement when the apparatus was filled with a) pure CO gas and b) a CO-CO2 mixture of the ratio CO-CO2 = 1:0.398, with Po, values calculated from the equilibrium constants of the following reactions at 1000°K:

Jan 1, 1968

By Russell Levens

A strategy for prioritizing mining health and safety research by evaluating the potential for risk reduction through interventions is proposed. Mining has one of the highest incidence rates of injury and disease found in major industries. The main premise of this paper is that often the best opportunities to reduce these rates are not revealed by retrospective analysis of injury and illness data. Instead, a proactive approach is needed that accounts for risks to specific hazards that can be abated by engineering or behavioral interventions. The process proposed here begins with development of prospective interventions. The degree of reduction in risk to be expected from an intervention then is determined from statistics on the mining worker population, the expected degree of success of the intervention, and the expected change in the severity of injuries resulting from the intervention. Three disparate mining health and safety concerns are presented to demonstrate common problems in assessing risks of injury and illness and describe additional data needs. Information on events preceding injuries and illnesses and more detailed demographic data on the mining work force are needed to analyze injury and illness data more precisely. Detailed information on exposure to specific hazards is necessary to evaluate the potential for an intervention to reduce risk of injury or illness.

By Ignaz Lichtig

[IN CONNECTION with its work on the conversion of coal to liquid cud gaseous fuels,3 the Bureau of Mines has always striven to keep informed of developments in this and related fields so that unnecessary duplication of effort could be prevented and so that useful ideas, presented in scientific and technical literature, could be evaluated as quickly as possible. Thus the E has compiled expensive literature and patent abstracts on the Fischer-Tropsch synthesis4 and hydrogenation d e venation of coal at elevated h temperatures and pressures.5 6 This publication differs from the references just given in that it covers patent applications, which may or may not have been approved for issuance as a patent, and also includes later material. The patent literature is, of courses, a valuable source for new ideas. German patent, have been particularly useful in this field because both processes for the complete conversion of coal to fluid fuels originated in Germany and were thoroughly investigated there because of the shortage or of indigenous fluid fuels. Among the German literature relating to these processes are patent applications. In contrast to the United States, Germany has a system in which applications are published before the final patents are issued. This arrangement permits the public to view all the applications and not just those for which a patent was granted as is done in the U.S. system. When main of the invention are judged not patentable by the German Patent Office, such documents nevertheless may contain useful ideas for scientists and engineers.]

Jan 1, 1961

By R. Barbaroux, B. Dubreuil, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"As conventional, base or precious metal ores are being depleted worldwide, the mining industry is being faced with an increasing exploitation of arsenical sulfidic ores. Enargite is a common example. The downstream processing of these ores poses several problems ranging from high smelter penalties to finding economical and environmentally acceptable means of disposing of the arsenic. Several hydrometallurgical processes have been proposed for extracting arsenic from enargite concentrates, notably using alkaline sulphide leaching (ASL). However, few alternatives exist for removing the arsenic from solution and stabilizing it in an approach that is both economical and environmentally acceptable.Dundee Sustainable Technologies (“DST”) has developed a technology for the sequestration of arsenic by vitrification. Originally optimized to cost-effectively stabilize arsenic trioxide (As2O3), DST has shown that vitrification could be successfully extended to the stabilization of other arsenical products, such as calcium arsenate (Ca3(AsO4)2) and sodium arsenate (Na3AsO4). In this paper, the vitrification of arsenic in the context of an enargite leaching was newly explored and demonstrated successfully.Two processing routes are being proposed by DST for the removal of arsenic from enargite concentrates and their stabilization by vitrification. In one route, arsenic is extracted by ASL and is then precipitated under atmospheric conditions and with minimal use of reagents and time. The resulting precipitate is an unstable hydrated ferric arsenate (FeAsO4•2H2O) that is then vitrified in a non-dilutive method, significantly increasing the stability of arsenic and meeting the TCLP guideline. Unlike is required for scorodite, stabilization was successfully achieved without concern for the crystallinity of the precipitate."

Jan 1, 2017

By Benoit Bissonnette, David Gelderland

"The Campbell Mine Constructed Wetlands has been in full operation, processing effluent from the water treatment plant of the mill circuit for the last two years.The overall results are extremely positive with dramatic improvements for the originally targeted parameters – Ammonia, Copper and toxicity.• Ammonia concentrations were reduced from an average of 5 mg/L to an average of 0.43 mg/L which translates to an average reduction of 91%.• Copper concentrations were reduced from an average concentration of 0.054 mg/L to an average of 0.019 mg/L, which translates to an average reduction of 65%.• LC50 Acute toxicity testing revealed no impact.• IC25 Chronic toxicity tests revealed no impairment to growth or reproduction.As a result of the improvements in discharge water quality from the wetland, 100 percent compliance with respect to all Certificate of Approval, MISA and MMER regulations for effluent will be consistently achieved.The system has proven to be very easy to operate and maintain, with a minimum of care. Given some basic rules are followed, the construction of the wetlands was straightforward and relatively inexpensive compared to other treatment methods.The ecological benefits of the operation of the wetland are also quite substantial, as is the positive image of the corporation in environmental stewardship.INTRODUCTIONOver the last four years, Campbell Mine has adopted an aggressive schedule for the development of wetlands for use as the final stage of effluent treatment within the tailings management facility. The focus of this work has been to utilize natural biological systems to provide Campbell Mine with a 100 percent compliant water quality with respect to all MISA, MMER and COA discharge criteria at all times throughout the effluent discharge period."

Jan 1, 2003

By Virgínia Morete Barbosa Bertolo

Ligas a base de zircônio são utilizadas na indústria nuclear devido à baixa absorção de nêutrons e alta resistência à corrosão em ambientes de alta temperatura e pressão. Nas condições de operação essas ligas estão sujeitas à fragilização pelo hidrogênio. Este trabalho visa avaliar o efeito do hidrogênio na liga ZirBrasil-1, produzida em forno elétrico a arco VAR (Vacuum Arc Remelting) nas condições: encruada e tratada termicamente. As análises de difração de raios-X indicam a existência de uma matriz Zr-a, hexagonal compacto, para todas as condições de tratamentos térmicos. Após a hidrogenação, ocorreu a formação de ZrH e ZrH2. Os hidretos formados são de pequeno volume e não conectados para as amostras laminada e tratada a 700°C/1 h e 800°C/2 h, sendo que a condição de 800°C por 6 h obteve a maior quantidade de hidretos por área e alguns hidretos conectados. Em todas as condições os hidretos se encontram espaçados ao longo da espessura das amostras. Os resultados de microdureza Vickers indicam a ocorrência de precipitação para tratamentos a 800°C e confirmam o efeito fragilizador do hidrogênio. A liga encruada absorve maior quantidade de hidrogênio, com início do processo de absorção ocorrendo após 12 horas, já a amostra tratada a 800°C por 6 h absorveu apenas 0,5%H e iniciou a absorção após 26 h. O conjunto de resultados permite concluir que a amostra recristalizada é a indicada para o desenvolvimento do processamento termomecânico, quando comparada a condição encruada devido ao maior tempo para início do processo de absorção e menor quantidade absorvida de hidrogênio.

Aug 8, 2018

By P. Bermingham

A new approach to load testing of high capacity piles is presented. The method is mobile, inexpensive, repeatable and non-destructive allowing for multiple pile testing at a single site. A reaction mass is placed over a pressure chamber situated atop the pile to be tested. The test method is significant in that it can produce linearly increasing forces of high magnitude (over 5.0 MN) with durations of up to 80 milliseconds. This represents pulse durations an order of magnitude longer than achieved using a drop hammer. The accelerations the pile undergoes are less than one g, (conventional dynamic methods = 50 to 100 g). These effects combine to produce pile behaviour no longer dominated by the action of stress wave, instead the pile is under high levels of stress through its length during the force input. This is representative of the situation when static loads are applied, thus the method may be considered quasi-static. Further advances introduced with this method are that pile deflection and transmitted force are measured directly by means of a laser beam and load cell. This allows accurate correlation of event load displacement histories without the error associated with zero shift (acceleration integration) or non-homogeneous materials (strain measurement). The load displacement histories emulate those obtained for static load testing.

Jan 1, 1989

By Kristineq Pankow

The August 2007 Crandall Canyon mine disaster raised national awareness of mining-induced seismicity (MIS) in Utah as well as general interest in how seismic monitoring might improve mine safety in the region. Unlike the situation in most other mining areas in the U.S., local seismographs in Utah?s Wasatch Plateau (WP) and Book Cliffs (BC) coal fields are an integral part of a modern real-time earthquake information system developed by the University of Utah Seismograph Stations (UUSS) as part of an Advanced National Seismic System. The UUSS earthquake catalog contains a continuous record of MIS at all active mine sites in the WP-BC region since 1978 (more than 18,000 seismic events = M 4.2). We describe characteristics of MIS and current seismic monitoring capabilities in the WP-BC region. We then demonstrate, using MIS from an example Utah coal mine, the ability to refine event locations with estimated absolute errors of ~200 m or less using a combination of (1) a double-difference relocation methodology and (2) ground truth information provided by mine operators. This approach enables sufficient spatial resolution to correlate MIS with mining activities, providing a useful tool to help improve mine safety.

Jan 1, 2008

By A. Lashagri

This paper presents research results on assessment of environmental impact of digging and loading equipment in surface coal mining. Environmental impact is accessed through the equipment exhaust and dust emissions, and sound level. Exhaust emission is related to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx), and volatile organic compounds (VOCs). Dust generation is expressed through the particulate matter PM10 and total suspended particulate matter (TSP), while sound is presented through the sound pressure level. Modeling of environmental impact of digging and loading equipment is conducted in Microsoft Visual Studio.NET software package. This research is a part of a boarder project on development of software system for the selection of productive, cost-efficient and eco-friendly mining systems, which is sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). The research work presented here may be used by mining professionals to aid in quantifying environmental impact of digging and loading equipment and determinate strategies for reducing its overall impact.

Feb 27, 2013

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By M Pizey, M Kingsbury

Since 1950 Stockton Open Cast Mine has excavated over 60 million tonnes of Brunner Coal Measures overburden sandstones and mudstones. The current operator, Solid Energy New Zealand, recognises that acidic drainage from this overburden and from historic underground mines has led to depressed pH levels and elevated levels of metals in streams draining the Stockton Plateau. These streams report to the Ngakawau River. To quantify the effects of mine site acid drainage remediation/mitigation on the lower Ngakawau River water quality, a catchment hydrogeochemical model has been field calibrated and ecotoxicology tests have been undertaken. The hydrogeochemical model indicates that pre-mining and present pH values in the lower Ngakawau River are similar but present aluminium and iron concentrations are elevated. Ecotoxicology tests have semi-quantified the critical metal concentrations and interim water quality targets to achieve ecological recovery are presented. Analyses of long-term total suspended solids (TSS) and turbidity monitoring in the lower Ngakawau River and St Patrick&apos;s Stream indicate that TSS of 120 mg/L and turbidity of 20 NTU are exceeded for &lt;20% per cent of the time. Hence, specific criteria to protect migratory native fish from turbid water are currently met in the Ngakawau River and St Patrick&apos;s Stream.

Jan 1, 2003

By E. J. Duggan

CLIMAX ore is an altered and highly silicified granite, about half of the gangue being quartz. Molybdenite is the only mineral recovered and most of it is intimately associated with the quartz in fine veinlets. Other minerals are molybdite, pyrite, and chalcopyrite. Although the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make this profitable. The pyrite ranges from 2 to 5 per cent and the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the problems is its elimination, and that of pyrite iron, from the final product. On account of the high degree of dissemination of the molybdenite and the necessity of eliminating the iron and copper, fine-grinding followed by flotation is the only known feasible method of concentration. Two factors, peculiar to Climax ore, have a predominating influence on the metallurgical attack: (1) Molybdenite is one of the most easily floated minerals. High recoveries may be made with pine oil alone if the

Jan 1, 1946

By Luis Valdivia

Dado que el objetivo principal de un departamento de Geología de exploraciones es el de estimar recursos minerales en nuevos blancos de exploración identificados a través del análisis e interpretación de información geológica proveniente de diversas fuentes. En ese sentido, el presente texto señala la sistematización de los datos geológicos como el uso de las imágenes satelitales, fotografías aéreas, geofísica, geoquímica, cartografiado geológico, sondajes diamantinos, catastro minero, datos geográficos y políticos, etc. a través de un servidor que integre dichas estructuras lógicas de conocimiento, de manera que todos puedan acceder a ella de manera fácil y dinámica. Asimismo, para los datos de carácter numérico llámense muestras, sondajes, leyes, se utiliza la plataforma Access como gestor de base de datos, mientras que para la información grafica superficial, el software ArcGis.

Sep 24, 2008

By Mark A. Jirsa

The Biwabik Iron Formation is a ~1.9 billion year-old sequence of iron-rich sedimentary rocks that was metamorphosed at its eastern- most extent by ~1.1 billion year-old intrusions of the Duluth Complex. The metamorphic recrystallization of iron-formation locally produced iron-rich amphiboles and other fibrous iron-silicate minerals. The presence of these minerals in iron-formation along the eastern part of what is known as the Mesabi Iron Range, and their potential liberation by iron mining has raised environmental health concerns. We describe here the geologic setting and mineralogic composition of the Biwabik Iron Formation in and adjacent to the contact metamorphic aureole of the Duluth Complex. The effects of metamorphism are most pronounced within a few kilometers of the contact, and decrease progressively away from it. The contact aureole has been divided into four metamorphic zones?each characterized by the composition and crystal structure of the metamorphic minerals it contains. The recrystallization of iron-formation to iron-rich amphibole minerals (grunerite and cummingtonite) and iron-pyroxene minerals (hedenbergite and ferrohypersthene) is best developed in zones that are most proximal to the Duluth Complex contact. ©2007 Elsevier Inc. All rights reserved. Keywords: Iron-formation; Mining; Fibrous; Mineralogy; Metamorphism.

Jan 1, 2007

By P. Cole Gregory, Michael R. Yenchek, John C. Edwards

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were under- taken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau&apos;s Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 1993

By M. Visser

Keywords: Pyrometallurgy, furnace, ferrochrome, Samancor, ferrochrome process Samancor Chrome has been, and continues to be, a major player in ferrochromium production. The company has a proud history and possesses benchmark technology and operations. Currently five business units are operating: two sets of mines and three smelter plants. Samancor Chrome produces around one million tons of charge chrome annually. Chrome ore, intermediate-carbon ferrochrome, and low-carbon ferrochrome, form part of the portfolio. Electrode paste is also manufactured through a joint venture with Highveld Steel and Vanadium. Samancor Chrome has a balanced approach towards operational strategy, and has entered into a number of joint venture partnerships. Through its access to quality raw materials, knowledge, and experience of various production technologies, and its strategic abilities, Samancor Chrome is well positioned to reap the benefits from opportunities in the current and future industry context.

Jan 1, 2006

By R. S. Bowman, G. S. Austin, J. M. Barker, P. S. Freeman

The physical, chemical and mineralogic characteristics of zeolites allow commercially important applications. While adoption of zeolite technology is slow in the United States compared to other regions of the world, continued testing and research has shown a wide range of uses for these minerals. They are important catalysts in petroleum refining, molecular sieves able to separate gases, and chemically inert carriers of reactants. The zeolite clinoptilolite produced by St. Cloud Mining Company (clino) (SC) is used in animal hygiene and animal feed, especially concentrated animal feeding operations (CAFOs), horticulture, water treatment, floor dry, aquariums, air and other filters, and odour control. Clino can remove cations from solution, and surface-modified zeolite (SMZ) is a sorbent for the removal of anions and neutral organics from water. Specific clino applications are: control of chemical pollution in groundwater, removal of organic compounds from oil field waters, and elimination of pathogens from sewage effluent. Combining the sorption capabilities of SMZ with chemical or biological transformations can yield complete removal of toxic materials from contaminated water. Continued development and marketing of zeolite products will be a growth market far into the future. The CAFO market for zeolites is the most significant growth area in the United States over the next few years. SMZ, currently less than 1% of St. Cloud sales, will continue to gain market penetration for many years.

Jan 1, 2004