Search Documents

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By T. V. Nguyen

The feedwell performance in gravity thickeners and clarifiers relies on the efficient mixing between solid particles and flocculant to achieve effective flocculation, as well as energy dissipation of the incoming feed stream. A population balance-computational fluid dynamics (PB-CFD) model has been developed and validated to provide new insights into the operation and performance of industrial feedwells. In particular, the PB-CFD model enables the efficacy of the main functions of a feedwell to be investigated for a wide range of feedwell designs and process conditions. This paper describes how PB-CFD was used in the design and development of a new feedwell concept for the flocculation of particles in a solid-liquid stream. The patented feedwell design includes an upwardly converging flow diverter to create two separate compartments for energy dissipation and flocculation. PB-CFD simulations of this simple and easy-to-retrofit feedwell design illustrate a superior performance in terms of flocculation and energy dissipation compared to typical feedwells over a wide range of flow conditions. The potential benefits include reduced flocculant consumption, better de-aeration, greater stability and the ability to cope with a wider variation in volumetric throughput, better flocculation and fines capture, and a more symmetrical discharge that may also offer improved overflow clarity in some applications. The new feedwell design has been installed in a full-scale thickener at an Anglo American Platinum site in South Africa. A number of operational factors complicate this application, but indications are that the new feedwell has led to improvements in stability and underflow properties.

Jan 1, 2012

The theme of the conference is "excellence", an epithet of special significance in tertiary education. It appears in the mission statements, goals and plans to achieve them of most, and quite possibly all, tertiary institutions in Australia. In the context of excellence, this paper examines the current statue of professional education in the principal mining industry related discipline of Mining Engineering. It furthermore, identifies and discusses a number of special problems in mining education that the tertiary sector has long endured. Some of these problems are becoming acute, and solutions will have to be found soon in order for the industry to be assured of the supply of well motivated and appropriately qualified young engineers and scientists necessary to achieve and maintain the excellent to which it aspires.

Jan 1, 1989

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By F. Enslin

Heavy metals and sulphates in acid mine drainage (AMD) can beadsorbed onto bentonite clay, leaving clean water and a heavy metal loaded clay precipitate as products. Due to the toxicity of heavy metals, the clay could not be disposed of safely in the past. A method was thus required to remove the heavy metal content from the clay. Acid leaching was proposed to liberate the heavy metals from the loaded clay. Sulphuric, nitric and hydrochloric acid were considered as lixiviants. Loaded clay samples were leached over a range of pH values from 1 to 3.5 to identify an optimum leaching condition. From the results it was found that metals can berecovered from loaded bentonite clay by means of acid leaching and the optimum pH for heavy metal liberation was found to be 2.5, with uranium as an exception, being optimally leached at a pH of 3. This allows for the possibility of selective leaching. Furthermore, X-ray diffraction analyses indicated that the clay structure did not deteriorate significantly during acid leaching, suggesting that the bentonite could be reused. The treatment of AMD with bentonite clay, and subsequent acid leaching of the clay, is a sustainable solution, and current outcomes could possibly lead to industrial implementation of the process during water purifying and metal recovery from waste streams. Keywords: Acid mine drainage, bentonite, heavy metals.

Jan 1, 2010

By Martin Hertzberg

This Bureau of Mines study concerns the use of the tube bundle method as a sensitive and reliable detector of mine fires. The method involves the pneumatic, sequential sampling of many points in a system through branching tube bundles that lead to a single analytic station of high sensitivity, good reliability, and convenient location. Two serious limitations inhibit its use: the relatively slow response times for long lengths of narrow sampling tubes and the wall-diffusion losses for submicrometer smoke particulates. These limitations were quantitatively evaluated by measuring tube transit times and smoke particulate transmissions as a function of tube length, diameter, and pressure drop. The comparison of the data with theory offered the challenge of extending the classical, incompressible flow solutions to the two compressible cases: isothermal and adiabatic. New equations were derived for these cases, and the measured transit time data gave reasonable agreement with calculated solutions in both the laminar and turbulent regimes. The measured transmission losses of smoke particulates from several combustion sources compared favorably with those expected from Brownian diffusion losses to the interior walls of the sampling tubes. Traveltime and smoke transmission graphs are provided and, pump power requirements are estimated.

Jan 1, 1976

By Tom A. Armour

Different variations of soil nailing techniques have been used in the United States since the late 1970's. Such techniques owe their origins to French developments, which began in the early 1970's as a spin-off from European tunneling excavation support practice. The growing demands of urban infrastructure development and rehabilitation and environmental protection have created an active and expanding soil nailing market demand for earth retention and slope stabilization in the United States since its early developmental years. There is a clear need for a fundamental review of the large number of soil nailing techniques that are currently being used in the United States. Following a brief summary tracing the historical development of soil nailing and a generic classification of applications, this paper provides a review of the different recent advances in the design and construction of soil nailed systems. Discussion topics include nail design advances, permanent "top-down", structure support/underpinning, alternative face stability measures, composite systems, hollow bar and fiberglass nails and architectural reinforced concrete/shotcrete facings. Case histories will be presented to illustrate each of these advances.

Jan 1, 2003

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

By K. Rambha Devi

The paper is an attempt to co-relate the findings of pile capacity using a number of formula suggested by various authors with the actual field load test results. Five locations consisting of wholly sandy or clayey soils were selected for this purpose. The clayey soils are on a hilly area having clays of medium to stiff consistency upto a depth of 20 m The sandy soils are near the bank of a river having angle of internal friction 'Ø' value ranging from 30 to 35 Degree. The details of the soil properties are given in Table-1 Bored cast-in-situ piles of 30 cm diameter and a length varies from 6.5 m to 13 m were designed and cast for load test to be carried out. The load applied was twice the design load. The load vs settlement curves were obtained. The theoritical values obtained by formula suggested by various authors were superimposed on the curves. From the careful study of these curves it is seen that De Ruiter and Berigen values are close to the actual results for clayey soil. For sandy soil it is found that both the BIS method and Meyerhof method found to give conservative resuslts. A multiplication factor is suggested to theoritical values for obtaining satisfactory results.

Jan 1, 1996

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By Ruxton B. P, Rhodes J. M

Two Rb-Sr ages are discernible in data concerning the leucocratic granite which is the youngest pre-sedimentation phase of the crystalline basement complex at Rum Jungle, Northern Territory, Australia. Whole-rockdata suggest that intrusion of this unit took place at about 2400 my ago, with a probable initial ratio around o·707; whole rock-potassium feldspar tie-lines indicate redistribution of strontium at about 1800 my ago. The former age correlates with other measurements on rocks which form basement to the mantling Pine Creek Geosyncline; the latter correlates also with isotopic evidence for regional metamorphism and emplacement of some younger intrusive granites elsewhere within the geosyncline. A few K-Ar ages, from scattered localities, conform generally with the later event or events which appear to have some connection with the structural deformation clearly observable both in the complex and the surrounding metasediments. It is these younger events which appear to match the residual evidence for the earliest detectable concentration of uranium minerals in the Alligator Rivers district.

Jan 1, 1977

By C. J. Newman

Before 1995, the smelting process at the Kennecott Utah Copper Corp. (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. When considering expansion, it was decided that the existing process would not lend itself to a program geared toward processing the total output of copper precipitate and copper concentrate from KUCC mining and concentrating operations. During 1989 and 1990, several smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1 Mt/a (1.1 million stpy) of copper concentrate, with the ability to expand to 1.2 Mt/a (1.3 million stpy). The smelter facility that used the Noranda technology was shut down in May 1995. The flash smelting furnace operation began in June with the flash converting furnace start-up a few weeks later.

Jan 1, 1999

By C. J. H. Steenkamp

Theoretically, the main driver behind a mining operations? sourcing decision should differ from company to company, and within a company from project to project, but in reality it often relates to cost. Research confirms that there are a number of factors, including cost, to consider when choosing between in-house and outsourced mining. While the literature is rife with factors to consider, little information exists on how to apply these in practice and the relative importance of the different factors to be considered. A study was conducted to determine whether mining is truly a core competency for a mid-tier commodity specialist mining company. Furthermore, a decision-making framework for mining operations sourcing was developed, and the critical success factors that should be adhered to if outsourced mining is chosen were determined. The research showed that owner mining is not a core competency for the mining company investigated. A decision-making framework was developed using the order winner/order qualifier structure, which can be used to facilitate the mining sourcing decision. The most important tools at the disposal of a mine owner?s team to manage a contractor miner are the social and output control mechanisms, according to the critical success factors study.

Jan 1, 2014

By M. M. Zarnan

This paper presents the results of s study involving characterization of ground subsidence of abandoned lead-zinc mines in northeastern Oklahoma. Two coordinated efforts were undertaken: (1) collection and analysis of available data such as driller's logs, geologic cross-sections, structure contour naps and stratigraphic sections, and (2) development of a numerical (finite element) technique for prediction of collapse and mine subsidence. An in-depth analysis of a major collapse in the region was conducted. The factors which contributed to this collapse were identified.

Jan 1, 1989

By Randy N. Powell

The Pipeline gold ore body was discovered in Lander County, NV in March 1991. Construction of the new mine and mill did not start until early March 1996. The $289-million project was placed on a fast-track development schedule upon completion of permitting and corporate approval. The mine and mill were commissioned 11 months after the start of construction and the project ended up $40 million under budget. Project design and construction management were provided by Placer Dome Project Development Division (PDD). History The Cortez Joint Venture has operated in northeast Lander County since the late 1960s. The business structure is comprised of 60% Placer Dome and 40%Kennecott Exploration. Throughout the years, production has been from several small open-pit deposits— Cortez, Horse Canyon, Gold Acres and now Pipeline.

Jan 1, 1999

By C. A. Horne

"The transportation of mineral solids in the form of slurry is a subject most of us are associated with and, in fact, live with on a daily basis. The design parameters of slurry systems and most important the prime movers or cent¬rifugal pumps, are frequent and often controversial subjects due to the lack of practical guidelines which, if known and followed, can increase both reli¬ability and service life of the equipment.In this talk, emphasis has been placed on the practical side or rule-of-thumb approach to applications which, in turn, has been related to successful field results. The theoretical content and complex design criteria associated with actual equipment design has consequently been held to a minimum in the following discussions.I. BASIC SLURRY PUMP DESIGN CONSIDERATIONSFirst, to better understand how a centrifugal pump performs work, a basic description of the operating principles are in order.A. Operation In a pump, mechanical energy is transformed into pressure energyby virtue of the centrifugal force exerted by the rotating impeller. The liquid is discharged by centrifugal force at a velocity required to generate a given head and the volute collects the liquid so useful work can be done by the conversion of kinetic energy to pressure energy."

Jan 1, 1976

By Richard J. Mainiero, James H. Rowland

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true. While there have been some disastrous world-wide accidents involving the transport of industrial explosives, this is not the case in the U.S. Over the past 10 years, accidents related to the transport of explosives used in mining and construction have resulted in 5 major injuries, 11 minor injuries, and no fatalities. Explosives and ammonium nitrate (AN) transport outside the U.S. has not had such a good record; there have been 4 major explosives or AN transport accidents resulting in a total of more than 300 deaths. Most of these fatalities could have been prevented if the accident site had been evacuated once the explosive or AN cargo began burning. The safe history of explosives and AN transport in the U.S. is due to diligent efforts by government, labor, and industry. However, accidents will become more common and disastrous if we become complacent.

By Richards S. M

The abundances and abundance relationships of lead, zinc, copper and silver in the major sulphide lenses at Broken Hill are examined, and their possible geochemical significance discussed.When expressed as atoms per cent, zinc is the most abundant base metal throughout the whole .group of orebodies, the highest average lead: zinc ratio (No. 2 lens) being about 0·45, the lowest (No. 1 lensZinc Lode group) being in the 0·12-0 ·14 range. Lead and silver are clearly higher in the lower two orebodies, but the abundance of zinc shows no apparent relationship with stratigraphical position. Among the base metals copper is conspicuously low and remarkably uniform, a feature noted in other conformable orebodies.Although, as has been recognised for many years, abundances of silver and lead, and lead and zinc, are sympathetically related, correlation within the pairs is variable and generally of low degree. Silver and lead show distinctly the better correlation, particularly in No. 3 lens. On the basis of lead: zinc ratios, No. 2' and No. 3· lenses, on the one hand, and the No. 1 lenses, Rhodonitic and Siliceous Zinc Lodes on the other, constitute two groups. However on the basis of silver : lead ratios, No. 3 lens stands alone, No. 2 lens showing clear affinities with the higher layers. Ternary relationships between copper-zinc-Iead and silver-zinc-Iead emphasize the very close constitutional relationship between the No. 1 lenses and the two "zinc lodes".The possible implications of these relationships are then discussed in the light of the' two principal theories-hydrothermal replacement or chemical sedimentation-held for the formation of the Broken Hill ores. It is pointed out that the ratios of the four metals in the ores are rather different from those found in most igneous and sedimentary rocks, and in seawater. For 'example, whereas copper and zinc are present in almost equal amounts in most terrestrial materials, copper in the ores is only about one-hundredth of the amount of zinc. Lead has increased somewhat, but the ratio of silver to lead has fallen; in spite of its recognition as a source of silver, the Broken Hill lode is impoverished in silver with respect to lead as compared with most common terrestrial materials.No solutions are offered to these prob'lems of abundance. Rather it has been the aim of the work to provide data, and to demonstrate the...

Jan 1, 1961

By H. Wallin, I. G. Wallace, J. Akhavan, E. Nilsson

Over the past three years the UK together with Sweden, Norway, Finland, Italy have been taking part in a EU funded Leonardo da Vinci programme. More recently EFEE have participated in the project known as the EU15/10/200715/10/2007Excert project which is aimed at addressing the perceived loss of explosives expertise in several EU nations. This could have implications for explosives safety and industrial competitiveness. The paper outlines the work that has so far been done in phase 1 and describes the work planned for the second phase of the project. The paper will describe work in the UK to develop competencies for all explosives workers in both the civil and defence sectors. These competencies in the form of National Occupational Standards have now been approved in the UK and are accompanied by a range of 24 new National Vocational Qualifications launched in May 2006. The paper will show how the standards define knowledge and skills and how these form the basis for vocational qualifications as well as higher education awards and professional qualifications. This UK initiative is now being considered in other EU countries and the project has now been extended to also include Germany, France, Portugal, Czech Republic, Lithuania and Estonia. To support the occupational standards and qualifications work is also being carried out to improve learning provision in the explosives area. In addition to formal educational and conventional training courses a series of workplace learning initiatives are being pursued as well as internet learning packages. Examples of these initiatives will be given.

Jan 1, 2008