Search Documents

With the exhaustion of orebodies close to the main haulage shaft of the Emperor mine, an increased rate of development, aimed at earlier investigation of values disclosed by exploration drill holes has been attained with an overall reduction in unit costs.This paper describes the techniques used in rates of advance up to and exceeding 1,000 ft per 28-day period.

Jan 1, 1966

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

CONTENTS PAGE ANDERSON, ARVID E., and CAMERON, FRANK K.-Recovery of Copper by Leaching, Ohio Copper Co. of Utah. Discussed by Thomas B. Brighton, H. C. Goodrich, Arvid E. Anderson, Thos. P. Billings, Frank K. Cameron 2 BEESON, J. J.-Mining Districts and Their Relation to Structural Geology. Discussed by Charles Keyes, Chas. A. Porter 4 DOBBEL, CHAS. A.-Deep-hole Prospecting at the Chief Consolidated Mines. Discussed by G. W. Crane 10 CRANE, G. W.-Notes on the Geology of East Tintic. Discussed by G. W. Crane, H. E. Havernor, N. O. Lawton 11 SACKETT, B. L., BARDWELL, CARLOS, JACOBSON, SIMON, and JENSEN, N. H. Lead Smelting in Utah. Discussed by D. W. Jessup, B. L. Sackett, E. H. Laws 13 BARDWELL, E. S., and MILLER, Roy H.-Pulverized Coal as Fuel for Copper Refining Furnaces. Discussed by L. D. Anderson, E. S. Bardwell, C. P. Crawford 15 WIGTON, G. H.-The Chief Consolidated Volatilization Process and Mill. Discussed by Thomas Varley, S. G. Olmstead, V. O. Lawton, O. C. Ralston.... 16 JESSUP, D. W.-Evolution in the Preparation of Ores for Lead Blast Furnaces. Discussed by W. Spencer Reid, D. W. Jessup, Carlos Bardwell 19 ALLEN, H. P., and MADGE, WM. C.-Chloridizing Mill of the Standard Reduction Co. Discussed by Thomas Varley, H. R. Hanley, H. P. Allen, George H. Dern 20 TUCKER, E. L., and HEAD, R. E.-Effect of Cyanogen Compounds on Floatability of Pure Sulfide Minerals. Discussed by Blarney Stevens 24 Mix, B. E., and BARKER, L. M.-Method of Unloading Ores and Coarse-crushing Practice at Magna Plant of Utah Copper Co. Discussed by W. C. Madge,B. E. Mix 25 KEIGLEY, C. T.-The New Byproduct Coke Plant of the Columbia Steel Corporation. Discussed by W. M. Grant, C. T. Keigley, A. C. Feilder 25 JACKSON, P. W.-Blast Furnace Plant of the Columbia Steel Corporation. Discussed by W. R. Phibbs, H. M. Henton 26 OLDRIGHT, G. L., KEYES, H. E., and WARTMAN, F. S.-Production of Ferric Sulfate and Sulfuric Acid from Roaster Gas. Discussed by G. D. Van Arsdale William E. Greenawalt, G. L. Oldright 27 MAZANY, M. S.-Braden Copper Company Caletones Smelter. Discussed by A. B. Young, G. L. Oldright 36 HARRINGTON, D.-Safety Methods in Utah Coal Mines. Discussed by Edward K. Judd, Otto Herres, Benedict Shubart, A. C. Watts, D. Harrington 36

Jan 12, 1925

By Steven W. Hunt, Isabelle Lamb, Steven B. Fradkin

Groundwater control is generally an important consideration and significant source of risk during most tunneling projects. Proper baselining of groundwater conditions requires: 1) a thorough understanding of the geological environment; 2) a focused site investigation; 3) identification of construction and adjacent property damage risks associated with inflows and short and long term piezometric level changes; and 4) consideration of contractual issues including restrictions on means and methods and pay items for associated work. This paper provides an overview of groundwater baselining issues and risks based on selected design studies and construction case histories.

Jan 1, 2005

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By Orr C. W

In previous papers (1, 2), the influence on the creep resistance of elements normally found in commercial lead has been recorded. The results in the present paper refer to the influence of calcium, an element which is not found naturally in lead, but which has been used commercially in the form of alloys. It was realised that calcium would act as a deoxidising agent for lead-and in fact it was with this feature in view that both calcium and magnesium were used as additions. Subsequent work (including the results given in the present paper) has tended to diminish the importance which at first seemed to be associated with the presence of oxygen in lead. The structure of the dilute calcium lead alloys has been worked out in detail (S) and the phase diagram shows the existence of limited solid solubility and a compound CaPbs.

Jan 1, 1938

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

By T. J. Lynch

A new class of polymeric dispersants for industrial minerals has been synthesized and evaluated. Currently available dispersants give initial low viscosities at high mineral loadings, however slurry viscosities can rapidly double or triple on standing over the first several days. The new dispersants give low initial viscosities that are more stable and maintain a lower viscosity for at least one month. The new dispersants are made possible by controlling the polymer molecular weight distributions during their manufacture such that essentially all of the dispersant is adsorbed onto the mineral surface, preventing depletion flocculation.

Jan 1, 2012

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

By R. D. Berkenkotter

Titanium and iron assays obtained from cores of three diamond-drill holes from the Cebolla Creek titaniferous iron deposit were evaluated by statistical techniques to obtain information concerning the mineral characteristics of the deposit and to make a preliminary determination of sampling requirements for the deposit. A range of sample volumes representing sizes from one-sixth NX core 2 feet in length through full NX core 10 feet in length were prepared by split-ting the NX core with a diamond saw and combining pulverized splits. Results indicate the existence of at least two statistical populations having different average grades of iron and titanium. Each has an assay frequency distribution that is not normal but is highly peaked (leptokurtic). Frequency distributions of assays from specific altered zones of the drill holes appear to be normally distributed. Increasing the cross-sectional area of the sample unit to change assay volume did not result in significant changes either in assay values or the resulting frequency distributions of assays. However, when assay volume is increased by increasing sample interval, the shape of the assay frequency distribution changes, and a normal distribution of assays is approached. Positive correlation exists between titanium and iron assays. The degree of correlation, although very significant, is too low to use for prediction purposes. Although the amount of data from three widely separated drill holes is not sufficient to establish an average grade for this large deposit, it indicates a range of expected assay values and provides some information for determining requirements of future sampling for evaluation purposes.

Jan 1, 1963

By A McDowell

Pound Road Quarry is an alluvial gravel quarry owned and operated by Fulton Hogan Ltd. for the supply of aggregate in Canterbury, and is the largest quarry in the South Island in terms of production. It has evolved from three separate quarries, as a result of which extraction has occurred sporadically in a number of areas. Due to this factor, and the need to manage environmental impacts, a detailed quarry management plan was completed in 1995 which formed the basis for implementation of a certified environmental management system.   In December 1997, the quarry was the first in New Zealand to achieve ISO 14001 (TELARC) accreditation for implementation of an environmental management system. The main potential environmental impacts arising from the quarry operation include dust, noise and groundwater contamination, and visual landscape effects associated with gravel extraction, the mitigation of which is achieved by means of æbest practiceÆ methods. All quarry operations are controlled in terms of the environmental management system by means of regular (monthly and yearly) environmental reviews, appropriate auditing of environmental documents, and monitoring of environmental targets in accordance with consent and statutory requirements.

Jan 1, 1998

By B. Weyerman

U. S. Steel's Oak Grove Mine experienced several top hinge failures on their caving shields. It was determined that all the caving shields needed to be replaced with new caving shields before more thilures occurred. The cost and amount of time needed for several scenarios of caving shield change outs were compared. This paper discusses how Oak Grove Mine decided to and did change 126 caving shields in six specially designed jig stations underground during a longwall move using their own UMWA employees.

Jan 1, 2001

By J. S. Peterson, G. P. Cole

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Feb 24, 1997

By Green P. F

Apatite Fission Track Analysis (AFTA) is a thermal history reconstruction tool that enables determination of magnitude and timing of maximum paleotemperature and paleo-geothermal gradient at the time of maximum paleotemperatures. From this information, the amount of section missing at major unconfornities can be estimated and incorporated into basin models. The Gippsland Basin has a number of distinct problems that can be tackled using AFTA. 1. The nature of the regional break between the Late Cretaceous-Tertiary Latrobe Group and the underlying Early Cretaceous Strzelecki Group. 2. The tectonic history of the basement flanking the basin and its effect on sediment composition. 3. The age of igneous activity in the basin, as typified by the widespread basaltic plugs and dykes intruding the outcropping Strzelecki Group. Major uplift and erosion within, and adjacent to, the early Cretaceous rift basin in the Mid-Cretaceous, at -95 to 100 Ma, initially constrained the Latrobe Group depositional area to the central deep of the Gippsland Basin and provided an elevated source of quartz-rich detritus for the Latrobe Group reservoirs. This is in marked contrast to the preceding period in the early Cretaceous when contemporaneous volcanism dominated as a source of detritus, producing quartz-poor lithic sandstones, in which a host of attendant diagenetic reactions destroyed their reservoir potential. Initial uplift and erosion of the volcanogenic Strzelecki Group also occurred in the mid-Cretaceous as revealed by a number of distinct inversion structures, and erosion of this material will have locally provided very poor quality sand to the basal Latrobe Group.

Jan 1, 1992

By R. A. Hill, J. D. Pitts

"Long distance slurry pipeline systems have been successfully trans-porting steam coal, iron concentrates, copper concentrates and limestone for an aggregate of nearly 60 years and nearly three billion ton-miles annually. A phosphate concentrate pipeline is nearing start-up and systems for coking coal, lead/zinc concentrates and fly ash are planned. The solids pipeline concept, first patented in the early 1900's and commercialized in the 1950's, is now a proven technology providing an economic, environmentally pleasing and safe method for long distance bulk transport.The challenge for larger tonnage and longer distance movements of solids, for traversing increasingly rugged terrain in grass roots mineral developments, for transporting untried materials and for shipping more economic forms of proven materials still remains. This has necessitated continued refinements and optimization of the technology. The economic and environmental incentives for slurry pipelines when compared to other transport alternatives has justified substantial activity in this area. The scope of planned systems in coal, iron and other minerals is indicative of the firm place slurry pipelines will have in worldwide mineral development.In this presentation, the state-of-the-art in long distance slurry pipelines is reviewed with a focus on major systems of interest to the mineral processing industry. An overview of new developments in the application of this concept is presented, and finally, a projection of the future of pipelines in mineral development both worldwide and in Canada is discussed."

Jan 1, 1978

By Xiao Caimei

The method of Substance Flow Analysis (SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level, such as copper, lead etc. In this paper the flows and inventory of cobalt in China, 2008, were traced with the STAF model, and the situations of production, fabrication and manufacturing, use and waste management in China were introduced. The result revealed that the resource of cobalt in China was so poor that a large amount of cobalt material or cobalt products needed to be imported, and there was lack of recycling of cobalt resources.0

Jan 1, 2010