Search Documents

By Brad R. Blair

This paper will review impacts on longwall design and ground stability assessment due to advances in mine automation and sensing technology. Several new approaches to the prediction and monitoring of longwall panel and gateroad stability have recently become mature, and are ready for application in problematic ground control situations. These methods are revealing significant detail regarding deformation and failure mechanics of critical underground structures. Examples of how these technologies have worked successfully will be given, and applications for the use of these tools for cost-effective engineering design and monitoring will be suggested.

Jan 1, 1996

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By H. Jang, Y. Kawamura

Unplanned dilution and ore loss directly influence not only the productivity of underground stopes, but also the profitability of the entire mining process. Stope dilution is a result of complex interactions between a number of factors, and cannot be predicted prior to mining. In this study, unplanned dilution and ore loss prediction models were established using multiple linear and nonlinear regression analysis (MLRA and MNRA), as well as an artificial neural network (ANN) method based on 1067 datasets with ten causative factors from three underground longhole stoping mines in Western Australia. Models were established for individual mines, as well as a general model that includes all of the mine data-sets. The correlation coefficient (R) was used to evaluate the methods, and the values for MLRA, MNRA, and ANN compared with the general model were 0.419, 0.438, and 0.719, respectively. Considering that the current unplanned dilution and ore loss prediction for the mines investigated yielded an R of 0.088, the ANN model results are noteworthy. The proposed ANN model can be used directly as a practical tool to predict unplanned dilution and ore loss in mines, which will not only enhance productivity, but will also be beneficial for stope planning and design.

Jan 1, 2015

By S. E. Khalafalla

In support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has investigated a novel hydrometallurgical system with sulfur dioxide. Differential leaching with dissolved SO2 of manganese, nickel, and cobalt from their hydrous oxides was found to be very rapid and efficient--almost instantaneous and quantitative. In this method a given weight of mixed oxides previously ground to minus 200-mesh is slurried with a leach solution containing a specified quantity of dissolved SO2 for 10 minutes at room temperature and ambient pressure. An empirical leaching parameter, R, is defined as the ratio of the number of SO2 moles in the leaching solution to the weight of the metal oxide charge. Plots of the variation of metal extraction with the ratio R generate a series of sigmoidal-shaped curves, each of which is characteristic of a specific metal extraction. A threshold value of R is required to initiate the leaching of a given metal from the mixed oxides. Once this threshold is reached, the metal recovery can increase to more than 95 pct in very short times. For increasing values of R, the extractability of various metals by SO2 follows the order: Mn > Ni > Co >> Fe, Al, Cu. Differences in the threshold R values permit a variety of metal separations to be made simply by adjusting the quantity of SO2 in the contacting solution. Success in this leaching system depends upon comminuting the sea nodules to less than 0.149 mm (100-mesh). Above this critical size, leaching is slowed due to the inaccessibility of inner particle reacting groups to the SO2 leaching agent. This results in nonselective extraction and less extraction of preferred metal values. At or below 0.149 mm, leaching by SO, is possible with all its attributes of selectivity, sensitivity, and rapidity. Leaching with HC1 solutions of the same pH level as dissolved SO2 yielded mixed, slow, and incomplete metal extractions. This observation rules out any interpretation based on hydrogen ion as the leaching agent. The leaching curves resemble the complexometric titration curves of heavy metals with specific coordination species.

Jan 1, 1981

By Michael Rieber

The increase in f.o.b. mine prices of coal from $5/ton to over $18/ton in five years [1] has increased the significance of transportation costs. Coals produced in the vicinity of the consumer bear a much lower transport cost than those produced in the west. This differential may be used for flue gas desulfurization, other cleaning, or further processing of local coals. To the extent that western coals are cheaper to produce and have a lower sulfur content, they offset the locational disadvantage. To the extent that they have a lower heating value, the disadvantage is exercabated. Given the other conditions, an accurate analysis of transport costs will help suggest the location of coal mining and the moue of transport both transport costs and tariffs have risen. Together they have increased delivered coal prices, altered the balance between the use of coal and other fuels, helped to alter the location of mining activity, and put pressure on consumers to examine the cost effectiveness of alternative transport modes. Transportation options for long distance coal movements include rail, barge, pipeline, and EHV transmission lines. A summary of system parameters is shown in Table 2.1. Barge transport, pneumatic and slurry pipelines are discussed elsewhere in this report. Together with EHV, they have been the subject of previous studies [2,3,4]. Slurry pipelines have been shown to be especially useful where rails are not available [2] but the technical problems of dewatering, handling, and utilization of lines [5] remain unresolved. They are discussed in Section 3. Barge transportation depends on the location of the mine and consumer with respect to the waterway system. One drawback of barge shipment is interruptions due to winter, and low or high water conditions. Mine mouth power generation followed by EHV transmission of over 500 miles has been shown to be the most expensive means of delivering an equivalent amount of energy to consumers [2].

Jan 1, 1977

By Belcher C. B

The Groote Eylandt manganese ore deposits contain mainly pyrolusite and cryptomelane with lesser amounts of the manganese minerals lithiophorite, todorokite, psilomelane, and nsutite. The major non-manganese minerals which occur are quartz, kaolinite, and goethite.Determination of the mineralogy relies mainly on x-ray diffraction analysis. Quantitative methods for the determination of pymlusite and cryptomelane in Groote Eylandt manganese ores have been developed, A large amount of isomorphous substitution may occur in the manganese minerals and a number of minor and trace element associations have been noted. A correlation has been established between the potassium and cryptomelane contents for a wide range of ore types. Anomalous calcium, magnesium, and sodium values occur in samples containing todorokite, and barium is associated with psilomelane. Groote Eylandt lithiophorite appears to contain negligible amounts of lithium (<O· 05 per cent).A relationship between the H20+ and the Al203, K20, and Fe203 contents has been estahlished indicating that much of the combined water content is due to the presence of kaolinite and goethite, and cap be removed by beneficiation of the ore.

Jan 1, 1975

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By Geir Martin Haarberg

Modern electrolysis technologies can provide possibilities for developing sustainable processes in terms of energy and environment. Laboratory experiments were carried out to study electrodeposition of iron from molten salts and aqueous solutions using an inert oxygen evolving anode to eliminate the emissions of CO2. The possibilities of molten salt electrorefining of metallurgical grade silicon to produce solar grade silicon were also investigated. Electrochemical techniques were used to study the electrochemical behaviour of dissolved iron, silicon, and titanium species. Bulk electrolysis was carried out to deposit pure iron, silicon, and titanium. The quality of the deposits was studied by SEM/EDS and XRD analyses. Calculations based on laboratory studies indicate that great improvements in terms of reduced energy consum

Jan 1, 2010

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By F. T. Cawood, M. A. Jooste

This paper describes the survey monitoring processes at Venetia, which are discussed under visual inspections, ad hoc investigations, system monitoring and slope stability radar monitoring. This is followed by a description of the main survey monitoring methods. The next section briefly states typical problems, i.e. the atmospheric corrections required to adjust total station distances, maintenance of the system and management of the monitoring process. The paper ends with some important lessons that could be applied to similar monitoring programmes. These lessons are firstly, communication is most important, process a vital part of the system, a champion must take responsibility for the programme and system planning ensures that the monitoring results are needs driven.

Jan 1, 2006

By D Jensen, L Riffo, S Yu, F Traczyk, D Meadows

With the steady increase of molybdenum demand worldwide and the favorable molybdenum market, many technological innovations on both process and equipment have been developed and applied in many modern molybdenum plants around the world. This paper introduces the most commonly used molybdenum flotation flowsheet, together with the introduction of the flotation chemistry. Many different types of flotation cells are used in modern moly plants, and each type of flotation cell has its own unique advantages suited for particular ore and process conditions. This paper tries to provide some insight and guidelines in flowsheet development and flotation cell selection in the molybdenum plants.CITATION:Meadows, D, Jensen, D, Traczyk, F, Yu, S and Riffo, L, 2013. Molybdenum flotation circuit and flotation cells, in Proceedings MetPlant 2013 , pp 387-398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By W B. Edgar, I M. Platten, C A. J Towsey, B W. Cuffley

The evaluation of historical goldfields has been common over the past 15 years, reflecting changing economic conditions, improvements in knowledge and technology and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins, which are structurally complex with an irregular distribution of gold, have variable geometry and architecture and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation, since it contributes to understanding the orebody, exploration target size and setting expectations. Mine records include documents such as plans, sections, reports, news cuttings, production tabulations, etc. A major advantage for the modern explorer is the capability of computer modelling to display this data in 3D. Historical records can give the explorer substantial information on various deposit characteristics, not least grade and geological continuity, geometry and architecture, mineralogy, metallurgical properties, bulk density and ground conditions. From an evaluation perspective, historical records can be used to support a Mineral Resource estimate, though its application will depend upon the quality and quantity of the data and judgement of the Competent Person. Effectively used, historical records can reduce geological uncertainty and focus evaluation efforts û thus reducing project risk.

Jan 1, 2009

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By Peter Kowalczyk

Magnetic surveying and map production is well established in land based mineral exploration. Magnetic data are routinely used to map geology in covered terrains, to estimate the depth to basement in overburden covered areas, and to identify altered zones, mineralization, bedding attitudes, and fault networks both regionally in map view, and through interpretation to depth in 3D. Best practices for magnetic survey methods and magnetic interpretation exist in all areas of land based geophysical survey methodology - mineral exploration, hydrocarbon exploration, geological mapping, archeological mapping, and in military applications. At sea, and particularly under the sea, sophisticated magnetic surveys are being done, but it can be argued that these are primarily in niche applications, for example in naval mine-hunting and UXO applications. Magnetic data is not normally collected on AUVs and ROVs conducting mapping and hydrographic survey operations. OFG has developed physical and mathematical calibration routines so that magnetometers can be mounted directly onto AUV and ROV bodies where significant heading errors and magnetic gradients exist. This simplifies the routine deployment of magnetometers on AUVs and ROVs for mineral exploration and other magnetic survey applications without the need for towed bodies, ungainly mounting frames, or degaussing of the survey equipment. Our experience shows that magnetometers can be operated routinely on AUVs and ROVs and that with careful processing useful maps can be produced routinely at low cost.

Sep 1, 2014

The more than 40,000 mining industry professionals that are expected to attend the National Mining Association’s(NMA) MINExpo International2000 trade show and conference will be treated to the exhibition’s largest display ever. The exhibit is expected to cover more than 60,385 m2(650,000 sq ft) and feature more than 1,300 exhibitors. The event is set for Oct. 9-12, 2000 at the Las Vegas Convention Center in Las Vegas, NV. Richard L. Lawson, NMA’s president and chief executive officer, said, “MINExpo 2000 will showcase everything that mining is proudest of. This is the largest premier mining exposition in the world.” MINExpo is held every four years.

Jan 1, 2000

By Jan E. Nesset, Colin Hardie, Peter Radziszewski, Donald P. Leroux

"The successful introduction of new high intensity stirred milling technologies (e.g. IsaMill, SMDetritor) to the mining industry in recent years prompted Noranda-Falconbridge to initiate a study comparing these technologies to the conventional technologies of ball milling and existing vertical stirred mills (e.g. VertiMill). The study was unique in that it utilized the same material (Brunswick Mine zinc cleaner regrind mill feed), the same sizing instrument (a Malvern laser difractometer) and sampling protocol, and media size and type (for the high intensity stirred mills). The paper compares the net energy efficiency (kWh/t) of the various technologies, their power intensity (kW/m3) and product size distribution spread (P80/P20). A key finding is that media size is critical to achieving optimal performance. As part of the performance comparison, an analysis of the four methods of power measurement was made (Prony brake, shaft torque, grinding chamber reaction torque, “no-load” correction) and followed-up with an experimental test procedure using three of these methods. The findings include divergent results for power measurements and some explanations based on the observations are proposed. The direct shaft torque and Prony brake calibration methods are shown to be the methods most suitable for stirred mills.INTRODUCTIONThe motivation for the investigation reported here was the lack of a suitable comparison within the available literature of relative grinding efficiency for the emerging crop of new industrial fine grinding technologies. Such comparisons are potentially fraught with inconsistency, from ore samples and grinding media used, to testing methodology, to size measurement techniques, to the power measurements themselves. The collaboration of the industrial suppliers (at the time MIM Technologies and Svedala, now Xstrada Technologies and Metso Minerals) and McGill University (P. Radsiszewski) were sought in order to ensure as valid a comparison as possible. The work was performed between October 2000 and November 2002, led by the mineral processing group at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. The paper is presented in two sections; Part A considers the different power measurement methods and a comparison of the results for the SMDetritor (SMD) technology, while Part B reviews the grinding performance of the 5 technologies investigated using the selected performance criteria."

Jan 1, 2006

By K. R. Griffin

Atmospheric conditions underground are constantly changing and from a safety perspective, it is critical to identify when conditions are trending abnormally. Atmospheric monitoring in underground coal mines allows mine operators to analyze atmospheric conditions underground in real-time. Real-time monitoring can then be used to identify whether atmospheric conditions underground have become problematic. The implementation of a risk assessment and management process allows operators to then use a risk-informed decision making to identify comprehensive site specific ventilation parameters. Establishing risk-informed ventilation parameters and tracking conditions relative to these parameters, management can modify ventilation plans as mine conditions develop to manage evolving risks. Ventilation risk assessment and management allows developing atmospheric monitoring technologies to be fully utilized in order to increase safety standards in the United States. This paper reviews general risk assessment approaches, state of the art ventilation based risk assessment, and the risk assessment and management application within the United States regulatory framework.

Feb 27, 2013

THIS paper proposes to give a general description of the pumping and other machinery in use at the Thames Hauraki Pumping Station, situated on the Thames goldfields of the North Island, New Zealand. An idea of the general arrangement of the pumping engines and pumps can be obtained, together with a certain amount of detail, by reference to the illustrations. The history of the pump is rather interesting, and is as follows: -In 1894 the Government decided that a subsidy of £1 for £1up to an amoUllt not exceeding £25,000 be granted towards the erection of suitable machinery to exploit the Thames low levels.With a guarantee of such assistance a company was floated in London, with a capital of £300,000, to develop several properties at Thames. As the old Queen of Beauty Company had produced bullion worth £400,000 prior to closing down on account ofa breakdown to its pumping gear, their shaft was chosen as the site of the principal work. As soon as the company was floated, operations were commenced at the Queen of Beauty shaft, situated at the entrance of the Waio-Karaka Creek, and not more than about half a mile distant from the principal mines on the field.

Jan 1, 1912

By Muhammad Azeem Raza, Samuel Frimpong

Underground mining environments are inherently hazardous and can lead to emergencies where effective rescue and self-escape become critical. Missouri University of Science and Technology is pioneering new technologies for effective self-escape. The rescuers and miners need to be trained in these new technologically driven environments. Previous research in fields like aviation, medical surgery, and oil and gas drilling has demonstrated the effectiveness of virtual simulation training, but the mining sector has yet to fully adopt advanced tools such as eye-tracking and immersive training modules. This research proposes a comprehensive training infrastructure incorporating these technologies to enhance situational awareness and decision-making during emergencies. The novelty lies in the application of advanced miner escape and communication technologies, specifically designed to monitor and enhance cognitive responses in high-stress situations. By leveraging these technologies, the proposed training infrastructure aims to prepare the next generation of underground miners and operators, by equipping them with the necessary skills to manage emergencies effectively.

Feb 1, 2025