Search Documents

By Y. G. Qin

In this article an experimental study of axial bearing capacity of half-closed steel pipe pile installed at BKSH dock is presented. In comparison with open and closed end piles, half-closed end pile is considered to have high bearing capacity and good penetration, that is, it not only has a capacity as twice as the same size open end steel pipe pile, but also has blow counts as half as the same size closed end steel pipe pile. It is economic to use half-closed end pile in soft ground without a deep deposit of thick stiff clay. This article also describes a large scale model pile test and preliminarily analyses mechanism of improvement of bearing capacity of half-closed end pile with emphasis on effect of squeezed soil on side friction; an empirical approach is presented in which side friction is related to density of squeezed soil and which is useful for reasonably chosing side friction of different types of piles in design of foundarion.

Jan 1, 2010

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006

By Allan Sylvester, Paul E. Gabryszak, Diane R. Hirsch, David P. Field

With construction of the first phase of the Automated People Mover (APM) Tunnels nearing completion, this paper will address how knowledge from recent Tunnel Boring Machine (TBM) and New Austrian Tunneling Method (NATM) tunnel construction at the airport was used to refine the methodology for the next phase of tunnels currently in design. The benefits include an enhanced understanding of the ground conditions; allowing optimization of excavation sequences and support requirements; a more effective instrumentation and monitoring program; and improved construction details and related contract provisions.

Jan 1, 2007

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By Marie-Pierre Bourdouxhe-Barnich

Since 1997, in partnership with the Laboratoire Central des Ponts et Chaussées in Strasbourg, ProfilARBED has been carrying out a vast study to qualify the improvements jetting can make to vibratory driving of steel sheet piles, and to understand its effect on the surrounding ground and on the sheet piles themselves. The process basically involves discharging a fluid (mostly water, sometimes in association with air) at controlled pressure and/or flow rate near the toe of the sheet pile being driven. The steel jetting pipes are attached to the sheet pile and are connected to the pumps by hoses. The jet of fluid loosens the soil, thus reducing the resistance at the toe of the sheet pile. Depending on ground conditions, the fluid that flows along the pile can reduce skin friction. Four soil types were involved in our experiments. Each site was instrumented: the driving parameters and the geotechnical characteristics of the soil before and after vibratory driving and jetting-assisted driving were recorded. Each test provided its own particular information which contributes to overall thinking on the matter and is of help to project managers who are often confronted with rapid driving to the final depth.

Jan 1, 2002

By E. J. Sun

The ADS system was developed to reduce accidents related to haul trucks operating under low visibility conditions in surface mining and construction sites, which is based on the GPS, mesh-wireless networks, and the Google-Earth 3D graphic engine as the graphic interface and mine-mapping server. This system has the capability to pin-point and track vehicles in real time using a 3D interface, which is based on user-based AutoCAD mine maps using the Google-Earth graphics interface. All equipped vehicles are shown in a 3D mine map stored in a local server through a wireless network. When low visibility conditions are present, the system indicates available exit/escape routes for driver safety. The research results indicate that the ADS system potentially increases reliability and reduces uncertainty in open pit mining operations by customizing the local 3D digital mining map, constructing the truck 3D models, tracking vehicles in real time using a 3D interface and indicating available escape routes for driver safety.

Oct 1, 2009

By C. Arthur Lefler

The hydrometallurgical processes for recovery of gold and silver in use at Round Mountain, Nevada and the practical aspects of the operation are discussed. Included are heap leaching by cyanidation, upgrading of solutions by adsorption of values on activated carbon and desorption (stripping) for electrowinning and subsequent refining steps to produce dore metal.

Jan 1, 1981

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

By S. S. Hsieh, J. R. Lehr

Bench scale beneficiation studies were made on Idaho dolomitic phosphate rock using the TVA carbonate flotation process. The process used diphosphonic acid as a phosphate mineral depressant and fatty acid as a carbonate mineral collector. Silica was subsequently rejected as float using an amine collector, with phosphate product recovered as the sink fraction. Two samples of prepared flotation feed from commercial operation were used. One contained 21% P205 and 3.2% MgO. The other contained 26% P205 and 1.8% MgO. The results indicate that concentrates containing 31% to 33% P205 and 1% or less MgO can be obtained, with about 80% P205 recovery.

Jan 1, 1986

By Akira Tsune, Shingo Sugimoto, Tadayuki Ishiyama, Nadao Saito, Masatsugu Okazaki

"The Deep Ocean Resources Development Co. Ltd. (DORD) of Japan signed a 15-years contract with the International Seabed Authority for exploration of polymetallic nodule in a 75,000 km2 area, consisting of West and East Areas in the Clarion and Clipperton Fracture Zone in 2001. The exploration work is now concentrated in resource estimation of the first generation of mining area, the High Abundance Area.A detail survey of the Model Area, set in the High Abundance Area, was conducted using AUV (Autonomous Underwater Vehicle) equipped with MBES (Multi-Beam Echo Sounder), SSS (Side Scan Sonar), Sub-Bottom Profiler (SBP) and still camera. The seafloor topographic map based on 1 m grid data was produced in an area of approximately 80 km2 (Figure 1). Photographs, continuously covering the seafloor taken by AUV along two west-east trending traverse lines, together with detail seafloor topographic map produced from MBES give an excellent opportunity to observe distribution manner of pollymetalic nodule related to topographic features. This helps to understand more accurate resources estimation of a whole area of the High abundance Area. Furthermore, information of micro-topography gives ideas for conducting ore collecting operation and designing ore collector."

Sep 1, 2014

Keywords: Pyrometallurgy, furnace, Lonmin, platinum, PGM, UG2 Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to its industry peers in the Platinum Group Metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that came with milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tap-block movement, the formation of three-phase ?mushy? zones, high refractory and tap-hole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to re-design Furnace No. 1, to invest in back-up furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line feed chemistry and mineralogy monitoring, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilising optical spectral analysis of the converter flame to characterise converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.   Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.   If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining) processing and marketing methods.

Jan 1, 1990

By Jack L. Taylor

As expected from similar crystal structures and favorable atomic size factors, titanium, vanadium, and molybdenum are completely soluble in one another above the transformation temperature of titanium. The fl phase parameters of the continuous solid solution are shown graphically. Limiting compositions for retained fl phase have been determined. VANADIUM and molybdenum both have body-centered-cubic structures at all temperatures and, from the atomic diameter comparison factor, 3.9 pct, would be expected to form a complete series of solid solutions. The existence of complete solubility has been confirmed by work' at the Jet Propulsion Laboratory. Furthermore, vanadium and molybdenum have favorable atomic size factors to form complete binary solid solutions with the B phase, high temperature form of titanium, which also has body-centered-cubic structure. Pietro-kowsky and Duwez' and Hansen et al." have established the existence of the complete series of solutions in these binary systems. It would be logical, therefore, to expect that p-titanium, vanadium, and molybdenum would be completely soluble in one

Jan 1, 1957

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

By Madgwick J. C

The monosaccharides glucose, galactose and arabinose, and the polyols glycerol and mannitol (0.1 Ufo WIV) supported pure and mixed culture heterotrophic bacterial manganese leaching of solid pyrolusite (MnO2, 2% W/V) to yield 14-38 mg/litre manganous ion in 3 days from a simple mineral salts media at 30°C. Supplementation of pure bacterial isolates growing on glucose with soluble intracellular photosynthate from freshwater algae (0.07 g/l carbohydrate) and marine algae (0.11 g/l) led to an improvement in Mn++ yields of 24 and 100 per cent respectively. Extracellular products of the freshwater algae (0.3 g/l carbohydrate) boosted recoveries by 57 per cent.

Jan 1, 1982

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

By M. Arlandi, J. C. Monge

In this paper, the finite element method is used to obtain deformations of a rock tunnel. More than 3,000 numerical simulations and calculations were carried out. The analysis of this results has allowed to achieve mathematical formulations and graphs, to obtain in advance support monitored displacements in tunnelling construction, so they can be predicted before excavation and supporting woks. The application of the presented formulations and charts will aid engineers to control tunnel monitoring, reducing decision time when problems occur. The analysis is limited to cases involving elastic behaviour of the terrain for tunnels of average to good quality in rock, and to excavation sections of average or smaller dimensions for road tunnels. The results show that, in all cases, mathematical expressions to obtain induced displacements around tunnel excavations, have similar pattern than Kirsch (1898) expressions for circular excavations. As corollary of the achieved results, a method to estimate in situ natural geostress ratio K0=sh/sv , by means of convergence measurements, is presented. In diesem Beitrag wurden die Verschiebungen eines Tunnels durch die Methode de Finiten Elemente berechnet. Mehr als 3000 numerische Simulationen und Berechnungen wurden ausgeführt. Die Analyse dieser Resultate hat es ermöglicht, mathematische Formeln und Grafiken zu entwickeln, die zur Voraussage der Verschiebungen in Tunnel dienen, auch unter Betrachtung der verschiedenartigen Abstützungen. So können die Verschiebungen vor den Erdarbeiten und dem Bau der Abstützung abgeschätzt werden. Die abgeleiteten Formeln und Grafiken werden vor allem einen grossen Dienst für Ingenieure bei der Mithilfe zu zeitsparenden Entscheidungen im Tunnelbau und bei der Tunnelkontrolle leisten. Die analysierten Fälle sind auf eine elastische Modellierung des Baugrunds beschränkt, sowie auf eine mittlere bis gute Qualität des Felsens und auf die Aushebung von Abtragungsabschnitten mittlerer oder geringer Grösse für den Strassenverkehr. Die Resultate zeigen, dass in allen Fällen die hergeleiteten Formeln zur Berechnung der durch den Tunnelbau verursachten Verschiebungen um den Tunnel die gleiche mathematische Struktur haben wie diejenigen von Kirsch (1898) für kreisförmigen Bodenaushub. Als Korollarium der ausgeführten Berechnungen wird eine Methode zur Abschätzung der vorherrschenden in situ Geospannungs-Verhälniss K0=sh/sv angegeben, die von den Messungen der Verschiebungen im Tunnel ausgeht. Dans cet article, la méthode des éléments finis est utilisée pour obtenir les déformations d’un tunnel creusé dans la roche. Plus de 3000 simulations numériques et calculs ont été effectuées. L’analyse de ces résultats a permis de définir des modèles mathématiques et des abaques afin de prédire, avant l’excavation et les travaux de soutènement, les déplacements auscultés pendant la construction du tunnel. L’application de ces modèles et abaques permettra donc aux ingénieurs de contrôler les déplacements durant l’auscultation du tunnel et de réduire le temps de décision lorsque des problèmes surviennent. L’analyse est limitée au cas du comportement élastique du terrain pour des tunnels creusés dans de la roche de moyenne a bonne qualité, et à de sections d’excavation de petites à moyennes dimensions pour des tunnels routiers. Les résultats montrent que, dans tous les cas, les expressions mathématiques permettant d’obtenir les déplacements induits autour des excavations de tunnel, présentent des similitudes avec celles de Kirsch (1898) pour des excavations circulaires. Comme corollaire aux résultats obtenus, une méthode pour estimer le rapport des

Jan 1, 2003

By Ben Hayes, Michael Ryjevski

The Palm Jumeirah is the smallest of the three Palm Islands (Palm Jumeirah, Palm Jebel Ali and Palm Deira). It is located on the Jumeirah coastal area of the emirate of Dubai, in the United Arab Emirates (UAE). The unique man made island is built in the shape of a date palm tree and consists of a trunk, a crown, 17 fronds and a surrounding crescent island that will form a breakwater. The Jumeirah Palm Island is primarily are treat and residential area for living, relaxation, and leisure. It will contain themed boutique hotels, three types of villas, shoreline apartment buildings, beaches, marinas, restaurants, cafes and a variety of retail outlets.

Jan 1, 2007