Search Documents

Jan 1, 1994

By Stephanie Singarayer, Damodara Reddy Chinnasane, Mike Yao, Danielle Pelletier

Mining at Vale’s Creighton Mine has been active for nearly 120 years in Sudbury, Ontario, Canada. Being the deepest mine in the Sudbury region, mining induced seismicity is a common occurrence at Creighton Mine. Over the past five years, 26 large magnitude seismic events ranging from 2.5 Mn to 3.7 Mn (Nuttli) have occurred. Out of these large magnitude events, three 3.0+ Mn events occurred between April 2020 and January 2021. The majority of the 3.0+ Mn events are believed to be the fault-slip type that could be linked to the known major geological structures and/or long-term effect of mining over many years. The recent large magnitude events are believed to be triggered by high induced stresses while mining the first few stopes of a new lower horizon in the top-down centre out mining sequence.

Apr 26, 2022

By Magnus Ruin

The dry deep mixing method for stabilization of soft soil has been used in the Scandinavian countries for 25 years. The typical application has been stabilization of soft inorganic clay. Today the method is used more frequently in organic soil with good results. The Limix System, introduced in the USA by Hercules Grundläggning AB and TREVIICOS Corporation, is a cost-effective dry deep mixing method used to stabilize most types of soft soil. This paper presents the general principles of stabilizing organic soil with the dry mix method and two case histories of soil stabilization projects in organic soil. Between October 2000 and June 2001 the Limix System was used in England to stabilize soft organic alluvium at the Channel Tunnel Rail Link, Contract 440. During year 2000 the Limix System was used in soft organic soil in Holland near the Groene Hart Tunnel entrance to support trench excavations for slurry walls and concrete barrettes.

Jan 1, 2001

By Rüdiger Wunsch

The new high speed Vienna - St.Pölten line and the Lainzer tunnel are to be connected to the existing Western railway line in Vienna. This involves building an underground cut and cover branching tunnel which will be connected to the Western railway line by ramps. A key structure is the Herzmansky Street tunnel, which has a length of some 820m. It is to be constructed as a cut and cover tunnel using the top down method. The walls of the tunnel are designed as a water resistant structure consisting of double walls, an outer wall of bored piles and an inner reinforced concrete wall. The bored pile wall will be used as a temporary retaining wall during the construction phase and will also be a structural part of the per­manent tunnel wall. The retaining walls of the open pit, which will have a depth of up to 14m and a width of 12m, were investigated as a non-contiguous bored pile wall and overlapped bored pile wall. Preventing ground water from penetrating into the pit is of paramount importance. The high ground wa­ter level is the determining factor for the dimensioning of the bored pile wall and results in the require­ment for a water resistant concrete structure. It has been necessary to adopt adequate measures, therefore, in order to reduce the hydrostatic water pressure during the construction phase, assuming economical pile dimensions.

Jan 1, 2000

By Steve Kral

More than 124,000 people involved in the mining and construction industries throughout the world poured into Las Vegas, NV in March for ConExpo-Con/Agg ’99. Show organizers said this triennial exhibition is the largest equipment show in the Western Hemisphere and one of the largest exhibition of any industry. “Clearly, Con-Expo-Con/Agg ’99 was one of the largest trade shows of any industry ever held in the Western Hemisphere,” said Bruno Benna, co-chair of the event. Attendees included mining industry representatives, including aggregates, and sand and gravel producers. In addition, many of the attendees work in the construction, reclamation, forestry, asphalt paving, landscaping and concrete industries. According to show records, about 52% of those attending were company presidents, vice presidents, chief financial officers or managers.

Jan 1, 1999

By C. Bazin

The separation of rare earth elements is a complex process that is industrially carried out using liquid/liquid extraction. Detailed flow sheets of solvent extraction plants for the separation of rare earth elements are rarely available in the literature which limits the opportunity to teach and test the application of data reconciliation, process optimization and control to these types of plants. The basis of a simulator for a rare earth elements separation plant is described in this paper. The simulator is used to adjust the organic phase and stripping acid flow rate in a separation circuit of heavy rare earth elements from light one?s.

Feb 27, 2013

By Sergio Estebanez, Martha Gross, Ruben Rubal, Yvonnick Rescamps, Alexandre Cochennec

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in coastal Virginia, USA will add two 1.5-mile (2.4 km) TBM bored tunnels alongside two existing immersed-tube tunnels between artificial islands. The site’s unusual constraints and the requirements of a large-diameter variable-density TBM shaped the design-builder’s decisions for handling TBM inputs and outputs, siting the TBM plant and supporting equipment, and sequencing tunnel-construction operations. This paper addresses the logistics necessary to enable key functions of the 46-ft (14-m) TBM and its ancillary equipment, including transport of most materials by barge, U-turn of the TBM on an artificial island, and delivery of materials for the second tunnel through the first one while interior structures are under construction.

Jun 13, 2021

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By Steve Collinsworth, Nils Heinke

In 1989, I realized the definite need for change in the Blast Hole Drilling Industry. With over 25 years of experience in dealing with the industry, I am well inGormed and educated concerning the problems that occur in Blast Hole Drilling. After continues interaction with the Drill & Blast Superintendents, Drillers, Purchasing Agents, Mechanics, and others in the field, a basic understanding was developed as to the origins of the main problems that the industry f&s with their drillings programs.

Jan 1, 1997

Overview ?G-9 Discovery Hole 420 drilled May 2005 ?14.16% Zn, 1.76% Cu ?Greenfield discovery built into the G-9 Mine in under 4 years. ?Utilized a unique ?Parallel Track? approach to fast-track mine development. ?Raised over $200million in financing without a Feasibility Study. ?Mine built for $149.7 million, only 20% over PEA. ?Commercial Production declared April 1, 2009. ?G-9 Mine has now completed the first year of commercial production on April 1, 2010. ?Initial cash costs per pound of zinc US$0.39/lb -US$0.45/lb range. ?Mill operating at over1,900 tpd in March 2010, well above design capacity (1,500tpd) only one year after starting commercial production. ?Balance Sheet -$167 million assets, $24 million long-term debt, $22 million cash. ?Restarted Exploration ?excellent initial results. ?Strategically positioning Farallon to grow to a mid-tier mining company.

May 1, 2010

By Gavin Ritson, Chris Ward

"The oil sands industry is still fairly young with the first viable oil sand operation having been started in Alberta in 1960. Since then numerous modifications and improvements have been tried and implemented. The current process makes use of high velocity pumping of oil sands slurry with hot water (hydrotransport) to achieve separation of bitumen from the sand.A number of the oil sands processes have been adapted from unit operations that are used in mineral processing, such as crushing, screening, flotation, cycloning and thickening. This paper outlines a typical oil sands process flowsheet and investigates the differences and similarities in technologies and costs to other mineral processing industries. It also considers the very large throughputs required, and presents some of the difficulties and challenges currently faced by the industry as a result of high demand for oil and environmental pressures.INTRODUCTIONOil sands (also known as tar sands) deposits are found throughout the world. The Athabasca Oil Sands deposit in Aberta is the largest of these. Oil sands consist of a mixture of crude bitumen (a semi-solid form of crude oil), silica sand, clay minerals, and water. The Athabasca, Peace River and Cold Lake deposits cover 141,000 square kilometers and contain about 1.7 trillion barrels (270×109 m3) of bitumen in-place, comparable in magnitude to the world's total proven reserves of conventional oil"

Jan 1, 2009

By P. C. Hodges

WHILE there is very little romance connected with the operation of a stone quarry, yet to those who have participated in the growth and development of a business that has been a pioneer in its field and that FIG. 1.-LOCATION OF PROPERTY OF MARBLE CLIFF QUARRIES COMPANY. has been in continual operation two-thirds of a century there is bound to be a background of experience, which if properly capitalized, brings progress as well as satisfaction in its accomplishment.

Jan 1, 1936

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

By M. N. Brodie

"The ability to adjust the speed of a SAG mill offers benefits to the process and to equipment maintenance. It can be provided with some slight effect on availability ranging from somewhat enhanced to somewhat reduced, depending on the particular equipment that is used. Several techniques have been developed for monitoring the magnitude of the contained charge, and several algorithms have been used to control mill feed rate and mill speed. The various benefits and the means by which they can be realized are examined and compared. Reasons for Variable SpeedProcess RequirementsThe recovery of minerals from ore is dependent on particle size and residence time in process. Separation in a given plant is most efficient at a particular rate and a particular size (e.g., 80% minus 200 mesh). If the particle size increases, less mineral will be liberated. If the particle size is significantly reduced, the process of choice may not be able to effect separation, and power, media, and maintenance costs would be increased.If a SAG mill-ball mill combination delivers the desired throughput at the correct size for efficient separation when processing ore of the design hardness, some adjustment must be made to maintain this condition when the ore changes. The processing of ore softer than design will result in overgrinding, unless:• the throughput is increased inversely to the change in hardness which lowers recovery by overloading the separation facilities;• or the SAG mill feed rate remains constant, but the speed is reduced to feed coarser material to the ball mill for finish grinding to the desired size.There is also the effect of changing milldiameter to consider. A nominal 36 ft diameter SAG mill will have an effective diameter of 35 ft with new liners and 35 ft 6 in. with worn liners. A mill designed to operate at 0.76 p.u. (per unit) of critical speed with new liners (9.84 rpm) will be changed to 0.765 p.u. with worn liners. If 0.76 p.u. is the desired value, the mill speed should be reduced to 9.77 rpm."

Jan 1, 2003

By Jerry Bennett

This report describes the results of a survey of current blast area guarding procedures at surface and underground metal/nonmetal mines. It features five case histories (two surface and three underground mines) of blast guarding methods considered to represent the best systems in use in the U.S. Mining Industry. Elements of an effective blast guarding system are presented along with recommendations for improvements in current blast guarding practices. Industrial and military surveillance and detection technology was reviewed to determine if parallel technology exists for immediate application to blasting site security. While it is concluded that immediate transfer of industrial security technology will be limited, a number of recommendations are advanced for new research to adapt some of that technology for application to the mining environment. Two research areas considered to offer the most potential for improved blast guarding are presented. They are, computerized personnel tracking and blast area intrusion detection using infrared, microwave or E-field type detection systems.

Jan 1, 1981

SEVERAL serious accidents, which had occurred owing to the platman leaving the plat without first withdrawing the "chairs" from the shaft, set the writer scheming to devise a mechanically operated system which would obviate such accidents and be "fool-proof". It was obvious at the outset that some means of indicating to the engine-driver by the movement of the "chairs" themselves, whether they were "in" or "out" of the shaft, was necessary.An arrangement of signalling similar to railway semaphores was considered, but was rejected owing to the difficulties accruing from the large number of communicating wires which would be required down the shaft-viz., 2 for each level. After several experiments, a comparatively simple and efficient electrical system was devised, and which is covered by Commonwealth Patent TO. 10,402.One of the chief features of the apparatus is its simplicity, and its strongest point is the fact that both the engine-driver and platman receive visual indication of the position of the "chairs." The arrangement consists of a miniature coloured glow lamp, one for each level of each shaft compartment, arranged and placed beside the numbers and arrows corresponding to the various levels, on the winding engine indicators. Also a large indicating glow lamp is installed at each compartment in the various levels, in proximity to the levers for operating the "chairs." Upon operating the various levers for the "chairs," an electrical current...

Jan 1, 1909

By Jimmy Rodríguez Las Heras

Durante la explotación de los niveles inferiores en la mina Yauliyacu, se generaron dudas sobre la ubicación de las concentraciones de esfuerzos y sus relaciones con los estallidos de roca. En este sentido, se instala un sistema microsísmico donde mediante el análisis de la microsismicidad se elaboró los estándares que permitieron reducir los incidentes por estallidos de roca presente, así como la frecuencia, magnitud y daños a las personas, y equipo e infraestructura de mina, debido a la energía liberada por los eventos microsísmicos. Por ello, el presente trabajo señala los beneficios del uso del sistema de análisis de microsismicidad como la actualización contínua de la zonificación minera de acuerdo a la concentración de esfuerzos, procediendo al reforzamiento del sostenimiento como medida de prevención.

Sep 21, 2013

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001