Search Documents

By S Hapugoda, H Han, L Lu

Charcoal produced from Syzygium Zeylanicum trees was widely used in ancient Sri Lankan iron smelting practices. Charcoal made from Syzygium Zeylanicum tree trunks, branches and leaves were analysed by optical mineralogy and SEM and found to contain unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOx) crystals in plant cells. Partial and full reduction tests of a high-P Brockman ore were conducted at several temperatures with coke and coke doped with CaOx and CaCO3. It was observed that CaOx promoted reduction and generated comparatively more metallic iron in reduced samples. Furthermore, CaOx encouraged phosphorous partition into slag phases than into the metallic iron, suggesting CaOx can a potential alternative fluxing material to calcium carbonate for treating high-P iron ores in ironmaking processes.

Sep 18, 2023

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961

By J. Gunaselvam

This article deals with an investigation into the specification and use of appropriate seating systems to reduce whole-body vibration (WBV) exposure in typical vehicles used in the SA mining industry. The EU Directive EU/44/2002 to be legislated in 2005 in European countries, provides legal and economic motivation for this project. The criteria for seat selection can be condensed to the requirements in the directive, which mandates an action level of 0.5 m/s2and a vibration exposure limit of 1.15 m/s2 for an equivalent 8-hour daily exposure period. As part of this study six suspension seats, which the manufacturers claim satisfy the requirements in ISO 70966, were tested to determine the most suitable seat for an articulated dump truck. Six test subjects, three ?light? and three ?heavy? as specified in ISO 70966, were used to estimate the seat transmissibility functions in the vertical direction of the six different suspension seats. Transmissibility functions were measured in the laboratory with two excitation levels of 1 m/s2 and 2 m/s2 r.m.s. in the 0.5?30 Hz frequency range, as well as one spectrum approximating the EM5 spectral class. SEAT values were calculated for road vibration data measured on a typical articulated dump truck. A set of seat selection guidelines that can be followed by vehicle manufacturers and suppliers, procurement officers and and the technical staff on a mine is proposed in this article. It is recommended that additional studies of the use and operating conditions of seating systems in the SA industry, as well as an epidemiological survey be commissioned to gather additional information on this subject. Nomenclature ADT Articulated dump truck DSTF Dynamic seat testing facility EM1 Frequency spectra associated with earth moving equipment (?articulated or rigid frame dumper?) according to ISO 7096 EU European Union ISO International Standards Organisation PSD Power spectral density r.m.s .Root mean square SEAT Seat effective amplitude transmissibility WBV Whole-body vibration

Jan 1, 2005

By John C. Stankus

At the 13th Conference on Ground Control in Mining, a paper was presented detailing a successful test in which a new truss system was utilized, in lieu of wood cribs, for tailgate support in the Pittsburgh seam (Stankus et al., 1994). Since that time, additional tests using this same truss system in the Pittsburgh and other seams are now complete. Also, several mines are now using trusses for full panel tailgate support with no cribs. Through an extensive instrumentation program, much data and new information has been gained from these tests and the full panel usage. From this data, not only have new concepts pertaining to tailgate support been developed, but also for headgate, pillar configuration, primary and supplemental support. In this paper, an update will be presented summarizing the results of these various tailgates.

Jan 1, 1995

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

By D Porta, E Grigolato, K Behrens

################

Aug 12, 2013

By V. Dinesen

"Grinding is simply the function of reducing particles in size or creating new surface areas. This may be accomplished by many means but we will only concern ourselves with the continuous grinding process as performed in a revolving drum or mill, containing a grinding media. Such a mill consists essentially of a feed head, a cylindrical shell section and a discharge head. To prevent internal wear of these parts it is customary to attach replaceable linings over the wear areas. The specification and design of these mill liners is more important than generally conceded. As they reduce the effective internal volume of the mill, they will consequently affect the whole mill ·design and operation.A number of mill designs of various sizes are available for combined crushing and grinding of materials within a wide size range. For simplif1cahon purposes we will refer 1n particular to conditions relating to standard mill shapes having a length which is greater than the diameter. Such mills usually rotate at speeds between 60% to 85% of the critical speed and may, depending on the grinding media used, be classified as rod mills, ball mills and pebble mills.LINER MATERIALSA great variety of materials have been and are being used for mill linings. These include wood, ceramics and cements, rubber and plastic compounds, rolled and forged steels, cast steels and cast irons, both plain, alloyed and specially treated.The choice of a liner material depends on many factors. In both dry and \\.:et grinding, it may be necessary to consider product purity, colour, chemical reaction etc. but for our purpose we \viii refer to wet grinding operations as generally used within the mining industry."

Jan 1, 1972

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

By H. J. Hutson

BRS, Inc. has utilized Carlson's Natural RegradeTM software to design the reclamation and stabilization of abandoned open pit uranium mine spoils, AML Project 16N, located in the Gas Hills Uranium District in central Wyoming. This work was completed for the State of Wyoming's Abandoned Mine Land Program (AML) on preSMCRA (Surface Mining Reclamation and Control Act) sites for which no reclamation obligation existed. The project successfully stabilized an eroding spoil dump, enhanced the local view shed, created habitat diversity and provided a significant source of fill material for open pit highwall hazard mitigation efforts. Additionally, the project served to evaluate innovative reclamation design methods, engineering software and grade control technology. This project was nominated for a National Association of Abandoned Mine Land Programs award by the State of Wyoming. The results of this project will be presented as a case history of the Natural RegradeTM approach to surface mine reclamation. Based on the successful application of this new mine reclamation technology on the AML 16N Project, reclamation designs for spoils associated with planned underground uranium mine operations at the Velvet Mine in the Lisbon Valley Uranium District of Utah for Uranium One USA, Inc have been prepared and will be presented. Critical elements will be the encapsulation of unsuitable materials, long term hydrologic stability, and sequencing and staging of ore and mine waste for final reclamation surface construction. The goal of the Uranium One Velvet Project will be to apply best available technology to reclamation planning and fully integrate the reclamation design with the mine planning. Benefits of the approach should include improved public and regulatory perception of the project, facilitate mine permit approvals and the eventual timely release of reclamation bonds, as it is anticipated the stable landform created through this process will result in more rapid stabilization of the site to pre-mine geomorphic conditions. NATURAL REGRADETM CASE STUDY AML Project 16N, D-9 and K Pit Reclamation Project, is located in an intensely disturbed area of the West Gas Hills Uranium Mining District in Fremont County, Wyoming. The overall design calls for the placement of approximately 7 million cubic yards of backfill materials in the D9 and K Pits, imported from adjacent mine spoils including the Central Spoils, and from local highwall excavation. Figure 1 shows the location of the Central Spoils excavation area, as well as the D9 and K Pits fill area. The entire project is located on public lands administered by the Bureau of Land Management, Lander, Wyoming District Office. No access controls are in place at the abandoned mine sites. The public lands are administered under a multiple use land policy including grazing of range land, public recreation, active mining and exploration, and oil and gas. The project site is located along Fremont County Road No. 5, which is a moderately well traveled road. Reclamation of the numerous and large abandoned open pits in the Gas Hills Uranium District has reduced the risk of death or injury to the public. Site History and Background The Gas Hills Uranium District was mined by multiple companies during the period from 1955 to 1981. The uranium was hosted in the Wind River formation, a sequence of soft sedimentary layers of interbedded sandstone, clayey shales, and conglomerates. Uranium was precipitated out of ground water in classic roll front deposits, which are found from very near surface to depths greater than 400 feet. Prior to the enactment of the Surface Mining Control and Reclamation Act of 1977 (SMCRA), very little reclamation work was performed when mines were abandoned or closed. The State of Wyoming Abandoned Mine Lands Program has worked to mitigate hazards associated with large open pits, control migration of unsuitable materials and restore watershed functionality of lands in the district. Additional reclamation is being performed by mining companies on bonded lands. Figure 2, Gas Hills Uranium District aerial photograph, shows the extent of the mining disturbance in the district. [ ] Project Hazards and Concerns The purpose of AML Project 16N is to mitigate hazardous conditions and risk to the public associated with open pit highwalls and toxic, acid forming, and /or radioactive mine waste materials. The D9 and K Pits are contiguous open pits characterized by an 8,800 foot long hazardous highwall that averages over 200 feet tall. In addition to the physical hazard presented by the highwall, the project addresses

Jan 1, 2009

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

By J. B. Forrester

In the operation of the coal mines in Utah few adverse conditions confront us. Physical conditions for the economical extraction of the coal are as near perfect as it is possible for them to be. Still several obstacles are encountered to keep up our interest and prevent us from getting in a rut. Of these I shall speak only of Burning, Wants, and Sluffing of Ribs. Should one travel the outcrop from Ivy Creek in Emery county to the Utah-Colorado line, there would be one outstanding feature indelible impressed upon one's mind. That feature is the omnipresent indications of burning in place. Viewing the eastern escarpment of the Wasatch Plateau from a distance, many splotches of dark red are plainly seen always lying above the coal floor. This stratum is a felspathic sandstone, appearing as a white line running the full length of the above escarpment and about midway between the floor of the valley and the top of the plateau. The coal bearing complex consists of shales, sandstones and coal. This complex varies from two hundred to eleven hundred feet in thickness. The number of coal seams are exceedingly variable. As a rule the argilutites form the bulk of this complex. This material is baked by the burning of the coal and the iron present is oxidized to the ferric state, coloring the shale to a dark red. This baked material forms a shingle tales that in places cover the entire complex. It is natural to expect that the most extensive burning is in the canyons facing to the south and east and on the south slopes of the ridges running to the east or west. Such, indeed, is the case. Still in this arid region many crop fires have existed upon the north slopes, especially in those canyons that face to the east. In fact today, instances are not rare where grassy north slopes, heavily timbered with balsam and fir that have attained a diameter of 14 to 24 inches, are found growing upon the disintegrated baked shingle and later development proves that the coal has been burned at least 500 feet back from the outcrop. Still these conditions are not normal. In this arid climate the south and east exposures are steep and barren, except for the scrub pine, cedar, mahogany and kindred semixerophytes. Bunch grass is also a lover of such exposures. There is very little soil found in such places; it is either blown away as fast as formed or washed away by the rare torrential rains, or the rapidly melting snow. Thus we see that the physical conditions are favorable for the starting and maintainence of outcrop fires. This brings us to the probable origin of this phenomenon. There are four probable ways' that such fires, could be started, namely:

Jan 1, 1921

By M. Mostert

Mining companies sponsor a range of non-core, corporate social responsibility projects to adhere to social and labour plans and environmental management prerequisites that form part of a mining licence application. Some companies go above and beyond such projects, sponsoring initiatives that generate renewable energy through solar power, wind energy, natural gas, etc. The challenge for these companies is to choose between a variety of projects to ensure maximum value, especially in times when the economic climate might be less favourable for such projects. The focus of this research was to analyse the concept of sustainability as it exists today, and to apply that to the triple bottom line accounting method in an attempt to quantify the sustainability of a project. Research was done on the methane burn-off project at Sibanye Gold?s Beatrix Mine to establish how such projects are planned and financed, and what impact they have on the triple bottom line of a company. The financial bottom line is, by definition, one that executives understand. This paper also proposes a quantitative method for defining the social and environmental bottom lines as well. By considering the financial, social, and environmental values, the study attempts to determine a monetary value for a sustainable renewable energy project. This monetary value can be compared to similar values obtained for other sustainable renewable energy projects under consideration. The research suggests that monetary value alone is not enough to base a sustainable decision on, and qualitative measures are suggested for use in conjunction with quantitative methods. The selection method proposed should assist the board of a mining company to choose the most sustainable option and the project that will add the greatest value to the company across all three bottom lines. It will also provide increased justification for such renewable energy projects, even in periods of harsh or uncertain economic climates.

Jan 1, 2014

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"The steps from experimental curiosity through to commercial product can be slow and tortuous in spite of the quality of the technological advances offered by the new development. Data generation and interpretation need to be done in lab tests as well as full-scale evaluations and, in each, the advantages of the new reagent must be clearly identifiable and measurable.The Dow Chemical Company has patented a novel new collector for the flotation of zinc. Fl (2-hexylthioethylamine hydrochloride) has several unique structural features that suggest atypical mechanisms for zinc collection. Laboratory data have demonstrated significant flexibility with respect to grade and recovery balance at dosages lower than those typically used for xanthates.In mill trials, the same phenomanon is evident - the choice between high grade and high recovery allows one to select the desired quality of zinc concentrate. One trial in particular was run over a three month timeframe and Fl gave improvements in recovery of 2.5% and a reduction in lead levels with less than 0.5% loss in grade. The dosages of other reagents in the flotation circuit were also reduced.Data demonstrating improved recovery and grade in lab trials will be discussed. Extensive data from the mill trial will illustrate how Fl works in both rougher and cleaner circuits."

Jan 1, 1990

By Bruce Vandenberg, Andy Bartfay-Szabo, Steve Conway

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to 500 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the SVClOOO system and compare these with the analogous aspects of film based cameras.

Jan 1, 1995

Sishen Iron Ore Mine previously used only A-grade material (>60% Fe in situ value) from the pit for beneficiating in the DMS plant to a final product grade of 66% Fe in lump and 65% Fe fine ore. The B-grade (between 50% and 60% Fe) and C-grade material (between 35% and 50% Fe) were stockpiled separately, owing to the inability of the existing DMS plant to beneficiate material at densities higher than 3600 kg/m3. The ability to beneficiate the B-grade material at densities higher than 3600 kg/m3 was evaluated, and air-pulsed jigs were found to be techno-economically feasible and value maximizing. The beneficiation of B-grade material would add to the existing DMS production of 28 Mt/a, with no additional mining cost and only limited costs for the handling of waste and B-material. The objective of the Sishen Expansion Project (SEP), i.e. the jig plant, was to produce 10 Mt/a of saleable product with six modules to the set physical and chemical specifications by 2009. During the start of construction, it was decided to add another two jig modules to the plant to increase production to 13 Mt/a. During commissioning and ramp-up the shortcomings and advantages of the jigs were fully experienced and understood, resulting in many changes to optimize jigging performance..

Jan 1, 2014

By Aly M. Mohammad

The 12th and 14th Street Viaducts, which carry Route 139, are located west of the Holland Tunnel in Jersey City, New Jersey. The two viaducts, provide access to and from the Holland Tunnel (which connects New York City and New Jersey) and carry upwards of 50,0000 vehicles per day from Jersey City and New York City to points west. The New Jersey Department of Transportation (NJDOT) selected AECOM to perform design services including rehabilitation and seismic retrofit for the 12th Street and 14th Street Viaducts while maintaining traffic at all times. Building a new parallel bridge just north of the 14th Street Viaduct was essential in avoiding extremely costly traffic delays. Installation of the new foundation, in close proximity to the existing viaduct, required drilling through some of the existing timber piles supporting the bridge. As a result, the existing bridge was required to be reanalyzed for this new foundation configuration. This proposed structure consisted of 8 piers each supported on a single six (6) foot diameter drilled shaft. Currently this portion of the bridge structure has been constructed. The shafts were constructed with rock sockets that were five feet six inches (5?- 6??) in diameter and were extended 11.2 feet (3.4 meters) into rock. A 2300 ton Osterberg Load Test was performed on one production shaft to confirm the capacity of the shaft. The rock socket for the test shaft was in sandstone. This paper will present a description of the design methodology and construction methods adopted for the foundations. In addition, the paper will illustrate the Osterberg Load Test including: equipment used, number and locations of strain gages, and interpretation of results. Additionally, regarding the close proximity of the new foundation, the paper will present the type of equipment used to drill through the existing timber pile foundation while minimizing the impact on the integrity of the existing foundation. We will also present the method of analysis for analyzing the redistribution of load on the remaining piles. The results presented in this paper will assist the design engineer by providing a comparison between the geotechnical design assumptions and the actual measurements obtained by field measurements for this rock formation.

Jan 1, 2009

By G Mark, K L. Blake, G de Jong, J F. Rotherham, N D. Adshead

Magnetite deposits with distinctive ¦ actinolite ¦ apatite-bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (egKiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (eg Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidised fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelised influx of a specialised high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

By Dan Payne

The Crinum mine has recently completed workings in the southern area of the mine. Over the 10 years of longwall production 40 million tonnes have been extracted and the mine has experienced over 40 longwall face, 3 main gateend, and 2 tail gateend roof falls as well as 5 roadway roof falls away from the longwall. Weak roof (less than 10MPa (1450psi) in the bolted horizon) has been the principal roof control issue at the mine. However, weak, highly cleated coal, water inflow from overlying aquifers, some minor structure and a diatreme in the main headings have also contributed to the challenges at the mine. This paper describes the geotechnical experience over the 10 years, the mine?s approach to addressing the issues and the relative success of these approaches.

Jan 1, 2008

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015