Search Documents

Discussion of the paper of Robert H. Richards, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2299 to 2303. C. D. DEMOND, Anaconda, Mont. (communication to the Secretary*) :-Any one who has observed the increased efficiency of the Wilfley tables in a mill when fed from a reasonably good hydraulic classifier, as compared with tables fed from a spitzkasten., which is a very poor classifier, will agree to the advantage of ? better classification." It must be gratifying to Dr. Richards to know that, directly or indirectly, maim mill men are responding to his persistent advocacy of correct principles of ore dressing and are accepting the results of his investigations. As he says, these principles mean much for both the conservation of resources and the profit of operators. When Dr. Richards gives us accurate figures as to the maximum size of free mineral grains in the tailings of the Wilfley table and of the vanner, they will be of a good deal of practical value in delimiting the proper fields for the Wilfley, the vanner, and the round table. He has coined the terms ? free settling" and "hindered settling."' The series may be completed by adding "crowded settling," the main principle of action on both the vanner and the Wilfley table, which is the principle of separation in a mass of grains crowded as closely together as they can be and yet continue free to move between one another; and the occurrence of larger mineral particles in the Wilfley tailing than in that from the vanner is apparently caused by the more violent agitation, due chiefly to the purposely sudden reversal of the stroke. It seems likely that the agitation caused by the wash water dropping directly upon the concentrate on the vanner is more harmful than that due to the shake. For the very finest material that can be concentrated by usual methods, the round table is superior to the vanner because it does not, have even, the gentle agitation of the latter. The action on round tables is, not crowded settling," but "film sizing," 2 but agitation is harmful in the latter action. George Gates proved this harm 20 years ago : in slaking the first successful large-scale application of canvas tables in California gold mills he abandoned all shaking motion, although he had patented canvas tables to which such motion was applied.

Jan 11, 1913

THE solid nonmetallic inclusions that are present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and. this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general the term "nonmetallic inclusions" seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those that occur as a result of reactions taking place in the body of the molten or solidifying metal and (2) those that result from the mechanical incorporation of refractories or other materials with which the steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulphidea but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from the molten or solidifying steel may be caused by (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change in equilibrium constants as the steel cools to the freezing temperature, (4) decreased solubility with lower

Jan 1, 1944

By W. B. Berwald

[Accurate ~cusirc::ie t of euusu.rface r,resw rus £Uld tee:: ?er:~t:,res in producin+ oil and as wells is one of tine ast iy,ulortant steps ever t,.s:en to place the rprwctice of retroleum ,-iroduction on an exact scientific basis. i'reerures and teial.or-tures in a -petrolcuia r4:, rvoir. have a rn..r..ed influence over the o:wvement of oil and ~c s both within the. reservoir and t~:rou,=Ii the various-size "flow otrin;;u" of proLucin,; wells to tine surface. Knovrled: ?c of theso fc,.ctgrs form a Laois for cny attei:ant to [.,-~ly eciantific j:cthods to the solution or analysio of mc.nj proble;ae encountered in the production of oil and 1c_c, Without a.ccur:tc mcaaurx,ients of reosures r:.nd tcn::paratuxes within the rocervoit and -well 'flo-,r strinL:s" tae aI,licution of w.ny proved enbinecrin and scientific princiy-,loo is on %,]

Jan 1, 1935

By Dirk van Zyl, S. Chander

Minerals have been critical to human society from the earliest and their use has been intertwined with the development of civilization. In the Western World, the mining, processing and extractive metallurgy associated with ores was first described in detail by Agricola in the 16th century. He considered these collective activities to be the most necessary and the most profitable of professions, and wrote, "without doubt, none of the arts is older than agriculture, but that of the metals is not less ancient; in fact they are at least equal and coeval, for no mortal man ever tilled a field without implements. In truth, in all works of agriculture, as in the other arts, implements are used which are made from metals, or which could not be made without the use of metals; for this reason the metals are of the greatest necessity to man." Ours is still a materials-dependent society that relies heavily on minerals for raw materials. Today our dependence on minerals is exceptionally great. To meet the need for fuel and non-fuel minerals in a representative year, in the United States alone, about one billion tons of coal and 2.7 billion tons of ore are mined. These mineral products are essential for fertilizers, for construction materials, metals and alloys, for manufacturing household and industrial items, for transportation, and for the generation of electric power. It is instructive to consider the diversity of uses found in our society for a single mineral product - silver, for example. Experts believe that in the past 5000 years we have mined about a million tons, or 31.9 billion troy ounces of silver. In 1988, 133 million troy ounces of silver were used in the Unites States. Most of the silver used was for techno- logical, medicinal and industrial purposes, Table 1. X-ray films, for example, carry comparatively large amounts of silver to lessen patient's radiation exposure. Silver does not prevent tooth decay, but each year about two million troy ounces of silver is used for dental work in the United States. In small quantities it is used in medicine. No metal - not even copper conducts heat and electricity so efficiently as silver. Silver wires lace solar cells, and silver oxide batteries power hearing aids, calculators, submarines and satellites. Hardened with tungsten or molybdenum, miniature discs of silver pass current from wire to wire in cars, telephones and computers. A dish- washer timer alone may have 50 such electrical contacts, which open and close without excessive heat or friction. Silver is an important component of solar reflectors, since no other material reflects light so well or uniformly. In our personal lives, silver remains in high esteem to adorn our tables, provide precious objects and jewelry. In many parts of the world, silver in the form of coins, jewelry and bullion is used for financial independence and security against the vagaries of paper currency. In India, silver is used in its purest form as thin foils to decorate sweets and other edibles. It is obvious that this mineral product, silver, is of great value and utility in our society. Minerals and Environment The benefits of minerals do not come without problems. Much of the silver, for example, lies locked up in copper, lead-zinc or precious metal ores; to extract it creates vast quantities of waste material. On the average, in order to recover one ounce of silver about a quarter ton of ore must be mined. To meet the world's annual demand for silver, approximately 100 million tons of waste is generated every Year. The problem with silver is repeated with all minerals. Conversion of mineral ores into usable materials necessitates the generation of large quantities of waste products that create tremendous disposal problems. In addition to waste material discarded during mining, wastes may be generated during processing as gases, liquids or solids that must be subsequently converted into forms more acceptable for disposal. Associated with the handling, treatment and management of waste products are a number of environmental problems. Environmental problems are not new to the minerals industry. In his Geographia, Strabo (63 B.C. - 20 A.D.), gives an account of the conditions of labor under which men

Jan 1, 1992

By Frederic P. Dewey

(New York Meeting, February, 1912.) By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called; platinum. Sometimes it is so, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes jives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid, 1 I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Apr 1, 1912

By George M. Fowler

EVERY year it becomes more difficult to find new mining districts and new ore deposits. Nearly all of the important discoveries so far can be attributed to surface manifestations overlying the ore deposit. In the future greater skill will be necessary to find ore deposits that give little or no indication of their presence. Mining geology is making progress by broadening its attack upon mineralized regions, by including in its investigations studies of the relation of physical-chemical processes to ore precipitation and various phenomena that heretofore have not always been looked upon as major factors in the problems. Such, for example, are petrographic peculiarities that will help determine structure, aspects of strata or formations favorable or unfavorable to structural deformation or mineralization, and renewed studies of chert and dolomite. This broadening attack is not necessarily being directed to the study of large areas, but rather by doing extremely detailed work in three dimensions in relatively small critical areas to find the key to the structure, reasons for the manner of rock deformation, composition and texture of the rock, and other con¬trolling factors in the larger areas.

Jan 1, 1935

By B. S. Crocker

Pebble grinding was used at Lake Shore Mines in 1949. A full description of experimental evidence and test plant results was published in 1952 1 and further operating details in 1954 2.' In more recent years the term autogenous grinding has been coined and is now frequently seen in the technical literature. Autogenous crushing and/or grinding covers any grinding mill in which the larger pieces of ore are made to grind the fine pieces; the crushing and grinding may be either dry or wet. This discussion deals only with wet autogenous grinding, and only in the fine grinding part of the circuit, i.e., from 6 mesh to 92 pct —325 mesh. The term pebble milling could apply to fine autogenous grinding in which the pebbles are made from the ore itself, or it could also refer to grinding with pebbles, such as flint pebbles, from a source outside the mine. The first mill to use screened ore to grind the ore (1949) was Lake Shore Mines, Kirkland Lake, Ont. Pebbles were screened from the jaw crusher discharge and used in 5x16-ft tube mills which had been converted to 6 ft 8 in. by 16-ft grate discharge pebble mills. The same general practice was adopted the following year by the Wright-Har-greaves Mine in Kirkland Lake. Shortly after that the Neptune Mines in Nicaragua started correspondence with the writer concerning the possibility of using screened ore for grinding in their plant. They first ran some plant-scale tests which confirmed the Lake Shore findings, with the ultimate result that their plant was successfully converted in 1956 to an autogenous grinding plant. In 1957-1958 the writer was successful in converting the grinding plant of Renabie Mines in northern Ontario to autogenous grinding. In all these plants the existing grinding equipment was converted, usually by expanding the diameter of the shell to make the change from steel grinding to ore pebble grinding mills. In all the above plants primary grinding was done in either small rod mills or ball mills. These mills first reduced the pebble mill feed to about 6 mesh. The final grinding in the pebble mills varied from 75 pct —200 mesh to 92 pct —325 mesh. At Lake Shore three stages of pebble milling were used, with a different size pebble in each stage. In other parts of the world interest was being shown in this form of grinding, and in March 1952 the writer had some correspondence with the mill staff at Outokumpu in Finland, with regard to the pebble system used at Lake Shore. At Stockholm in 1957 the account of the crushing and grinding system at Outokumpu was presented in a paper by H. Tanner and T. Heikkinen.V his is the only ore grinding plant that does not use grate discharges on its pebble mills; trunnion discharges equipped with heavy reverse spirals retain the pebble load. The first new mill designed to use screened ore as a grinding medium was the Bicroft mill at Bancroft, Ont., which began operation in the fall of 1956. In 1957 this plant was followed by similar installations at Faraday Mines, also in the Bancroft area, and the North Rankin Nickel Mines in the North West Territories. In 1958 the Dyno Mill at Bancroft was converted, using the same type of grinding. Since all these plants, designed by Kilborn Engineering (1954) Ltd., were originally planned as pebble grinding mills, they were able to take full advantage of the latest design and technique. They are neat in appearance and very efficient and easy to operate. Effect of Ore Hardness: It is often commented that this type of autogenous grinding applies only to hard siliceous ores. Experience has shown that this is not so. In the past ten years the author has had an opportunity to test more than a dozen ores, several of which were quite soft. One of these was shale. The softer ores actually make better looking pebbles than the hard ores. These soft ores produced no particles in the intermediate size range which could not be ground by the largest pebbles in the mill charge. Slabby ores, such as shales, make a suitable pebble for the —6 mesh grinding. It is not generally recognized that for fine grinding a spherical medium is not essential or more efficient. Another frequent objection to pebble grinding is the belief held by some operators that there is too much variation in the hardness of their particular ore to make it acceptable as a source of pebble media. Experience has also shown that this is not a serious problem at all. The variation in pebble load due to changes in the ore hardness is nothing like as great as most people would expect, and the method used for feeding the ore and controlling the the load in the mills is more than sufficient to take care of daily variations in ore hardness. This point

Jan 1, 1960

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are some- times large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy Bureau of Mines- sponsored subsidence study at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County) , West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar re- treat mining. Findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water levels at shallower depths. Post-mining values of hydraulic conductivity were typically somewhat higher than pre-mining values. Changes in water chemistry associated with mining were not sufficient to render the water unfit for human consumption.

Jan 1, 1986

By Peeler P. K

The recent renewal of interest in hydrometallurgical routes for copper production has been brought about by the possible future reliance on mixed ores and lower grade deposits, environmental aspects, and energy considerations.A number of hydrometallurgical processes for the recovery of copper have recently been proposed. Flowsheets are developed for two processes which incorporate several treatment methods being experimentally studied in Australia.In the first process a cupric chloride leach is followed by electrowinning whilst the second is based on the formation of cuprous ions, stabuized by acetonitrile and subsequent disproportionation to cupric ions and metallic copper. For the purpose of comparison, flowsheets were also developed for the Arbiter and Cymet processes.Process economics are estimated for the four processes and the results are discussed in relation to competitive pyrometallurgy. None of the four hydrometallurgical processes, with possible exception of the Cymet process, appears to be competitive with established large scale and newly developed pyrometallurgical processes for chalcopyrite.However, because the economics of the individual hydrometallurgical processes depend strongly on specific conditions, a "tailored" process may be competitive with pyrometallurgy in particular circumstances.

Jan 1, 1977

THERE are three objectives in translation of works of this character : to give a faithful, literal translation of the author's statements ; to give these in a manner which will interest the reader ; and to preserve, so far as is possible, the style of the original text. The task has been doubly difficult in this work because, in using Latin, the author availed himself of a medium which had ceased to expand a thousand years before his subject had in many particulars come into being ; in consequence he was in difficulties with a large number of ideas for which there were no corresponding words in the vocabulary at his command, and instead of adopting into the text his native German terms, he coined several hundred Latin expressions to answer his needs. It is upon this rock that most former attempts at translation have been wrecked. Except for a very small number, we believe we have been able to discover the intended meaning of such expressions from a study of the context, assisted by a very incomplete glossary prepared by the author himself, and by an exhaustive investigation into the literature of these subjects during the sixteenth and seventeenth centuries. That discovery in this particular has been only gradual and obtained after much labour, may be indicated by the fact that the entire text has been re-typewritten three times since the original, and some parts more often ; and further, that the printer's proof has been thrice revised. We have found some English equivalent, more or less satisfactory, for practically all such terms, except those of weights, the varieties of veins, and a few minerals. In the matter of weights we have introduced the original Latin, because it is impossible to give true equivalents and avoid the fractions of reduction ; and further, as explained in the Appendix on Weights it is impossible to say in many cases what scale the Author had in mind. The English nomenclature to be adopted has given great difficulty, for various reasons ; among them, that many methods and processes described have never been practised in English-speaking mining communities, and so had no representatives in our vocabulary, and we considered the introduction of German terms undesirable ; other methods and processes have become obsolete and their descriptive terms with them, yet we wished to avoid the introduction of obsolete or unusual English ; but of the greatest importance of all has been the necessity to avoid rigorously such modern technical terms as would imply a greater scientific understanding than the period possessed. Agricola's Latin, while mostly free from mediaeval corruption, is somewhat tainted with German construction. Moreover some portions have not

Jan 1, 1950

By Rita D. Sylvester

"This compilation lists and summarizes publications by Bureau authors published in the regular Bureau of Mines series, in scientific, technical, or trade journals, or in other media; those available from the Bureau of Mines are indicated. Patents issued to Bureau personnel are also listed, and instructions are given on how to apply for permission to use them. One of the outstanding features of this Special Publication is an exhausive subject and author index. IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and present their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries, The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminar's; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1970, to December 31, 1974. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;3 and the 5-year lists of Bureau publications and articles from January I, 1960, to December 31, 1964,4 and from January I, 1965, to December 31, 1969.5 It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1970, to December 31, 1973."

Jan 1, 1975

By G. J. Hasenfus

There are no known published methods of estimating the degradation of coal measure rocks by water that are simple and efficient, yet still provide a quantitative, meaningful value for assessing the stability of coal mine floor, roof, and rib. The slake durability test, the standard index method for estimating the durability of rock subject to wetting, can provide misleading results for floor stability assessment. Additionally, slake durability testing is time consuming and requires specialty equipment. Methods based on humidity cycling have been demonstrated to be very effective for assessing coal mine roof, but require specialty equipment and do not address floor stability concerns. Visual observation techniques, such as that developed for the Coal Mine Roof Rating (CMRR) method, adequately qualify rock degradation, but lack quantitative rigor. This paper will describe an alternative method, coined the water sensitivity test, originally developed for floor stability analyses, but also found applicable for roof and rib stability assessment. The test was developed by CONSOL in the early 1990's, and in its current form, has been in use for approximately twelve years. The method is based on the basic slake durability principle of measuring the mass of the rock retained on a screen after submersion in water. The new test employs two screens of different sizes, and also uses modified submersion, drying, and data processing procedures. The method is relatively efficient and can be geared toward batched testing. As with the slake durability test, the resulting index value provides a quantitative measure of the susceptibility of rock to water degradation. In addition to discussing the test method and its development, this paper provides a comparison of results with those fiom standard slake durability tests, and tabulated results for various types of coal measure rocks. Examples of the technique's utility are provided, including assessment of longwall and development floor conditions, roof and rib rock weathering and stability, and drum-bit cutability.

Jan 1, 2005

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By Robert Linton

THE PURCHASE of silver by the United States Government under the provisions of the Pittman Act is practically completed. Producers of silver in this country will now have to market their silver in competition with the rest of the world. It therefore becomes of interest to study such data as are available and endeavor to obtain such suggestions as may be afforded therefrom as to the probable future market position of the metal. Conditions influencing the marketing of silver are numerous and complex. It is a commodity entering. into the arts and manufactures, and therefore influenced by the condition of various lines of business which make use of it; it is currency-being used by all countries for subsidiary coins and even as the founda-tion of the system by a very few; and it serves as a frequent basis for speculation. The various factors involved can easily set up so many cross-currents in the flow of the metal that predictions in regard to the market position of silver can never be safely made, although it may be possible to form some idea of prob-able trends over a sufficiently long period. Of course price is determined, as is the case with all commodities, by the inexorable workings of the law of supply and demand.

Jan 6, 1923

By W. J. Birch, R. Farnfield, S. Hosein, C. Johnson

Modern smart phones include accelerometers based on MEMS (Micro Electro Mechanical System) technology giving the possibility to measure both acceleration and orientation. The widespread use of such phones has driven technological development to such a degree that it is now possible to obtain a triaxial accelerometer unit, that also include signal conditioning and analogue to digital conversion, in a package smaller than 1 cm2 (1/2 sq.in) for a relatively low cost.

Feb 6, 2023

By Andrea Lisjak Bradley

Clay shales are currently being assessed as possible host rock formations for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this thesis was to develop and validate a mechanically-based model of the deformation and failure process of a clay shale, namely Opalinus Clay (OPA), with particular focus on the influence of anisotropy on the short-term response of circular tunnels. To achieve this goal, a hybrid continuum-discontinuum numerical approach was developed in combination with new field measurements from the Mont Terri underground research laboratory. The response of OPA during the excavation of a full-scale emplacement (FE) test tunnel was characterized by geodetic monitoring of wall displacements, radial extensometers and longitudinal inclinometers. The deformation measurements indicated strong directionality induced by the combined effect of in-situ stress field and bedding planes striking parallel to the tunnel axis, with the most severe deformation occurring in the direction approximately perpendicular to the material layering. Computer simulations were conducted using a newly-extended combined finite-discrete element method (FEM/DEM), a numerical technique which allows the explicit simulation of brittle fracturing and associated seismicity. The numerical experimentation firstly focused on the laboratory-scale analysis of failure processes (e.g., acoustic activity) in brittle rocks, and on the role of strength and modulus anisotropy in the failure behaviour of OPA in tension and compression. The fracturing behaviour of unsupported circular excavations in laminated rock masses was then analyzed under different in-situ stress conditions. Lastly, the proposed modelling methodology was applied to the aforementioned FE tunnel to obtain unique insights into the EDZ formation process around emplacement tunnels for nuclear waste. The calibrated numerical model suggested delamination along bedding planes and subsequent extensional fracturing as key mechanisms of the damage process potentially leading to buckling and spalling phenomena. Overall, the research findings are already having a direct impact on the preliminary design process of an underground repository for nuclear waste in Switzerland.

Jan 1, 2015

By J. H. McKibbon

THE metallurgical industry has purchased more than sixty per cent of the industrial gas cleaning equipment installed in Canada. This includes cyclonic collectors, scrubbers, cloth filters and Cottrell Precipitators. These are the principal types of equipment which are used commercially for the cleaning of gases which result from the processing of iron, nickel, copper, lead, zinc, gold, gypsum and aluminum ores. The recovered dust, which usually contains metal values, is returned to the process. The cost of the equipment is thus economically justified. This is in contrast to other industries, such as those involving steam power generation, asbestos, cement and lime production, where, though dust collection equipment is extensively used, it is installed primarily for nuisance abatement. Communities are becoming more and more conscious of air pollution, new and more stringent legislation is being enacted, and, for other than economic reasons the smelting industry will eventually be required to install more efficient gas cleaning equipment. This paper

Jan 1, 1962

By Heribert F. Broicher

By the very nature of mineral deposits the quality of the raw material generally fluctuates and should be known for optimum processing. Early classification, for example, of limestone into road-metal grade or lime grade or of run-of-mine ores into high grade, low grade and waste as well as information for blending or for dosage of reagents are prerequisite for economic processing. Non-contact, real-time and on-line rock identification or assessment of quality parameters can be realised by introducing the analysis of laser-induced fluorescence (LIF) into the mining industry. LIF analysis is an optical method evaluating the basically known photoluminescence properties of matter, however, extending the application into hitherto unimagined fields by use of high-energy pulsed lasers and time-resolved analysis of fluorescence in the ultra-violet, the visible and near-infrared domains of light. LIF analysers and test work in a limestone quarry and a cement plant in Germany as well as in an iron ore mine in Sweden are described. First results of test work are available and proof this technology to be promissing.

May 1, 2002

By E. S. Moore

"The Centre of the silver-producing section of the Gowganda area lies about 55 miles northwest of Cobalt, and the village of Gowganda is 71 miles by road from New Liskeard. The geological similarities of the Gowganda and Cobalt areas led prospectors westward from the rich Cobalt field, first to Elk Lake and then on to Gowganda, where mineralization was found in 1907. A year later many showings were found, and rich hand-picked ore was shipped. Most of the ore has come, however, from two mines, both of which are still operating; the Miller Lake-O'Brien, which was purchased by Siscoe Metals of Ontario Ltd. in 1945, and the Castle-Trethewey. The annual production of these two mines runs over one and one-half million ounces of silver and considerable cobalt. The total production of the camp has reached about 32,000,000 ounces of silver and a large amount of cobalt, the total not recorded.General GeologyThe general geology of Gowganda is in many respects much like that of Cobalt. There are areas of Keewatin basic and acid Javas mixed with tuffs and basic intrusions. These rocks are deformed and partly altered to schists, and have been intruded by some Haileyburian basic and ultra-basic rocks and by Algoman granite. These were followed by a large number of porphyritic Matachewan quartz diabase dykes. After a period of extensive erosion the Huronian sediments were deposited on a pene-planed surface over all the older rocks; these sediments include large quantities of conglomerate (partly tillite), quartzite, and greywacke. The Keweenawan rocks include the Nipissing quartz diabase sill, later quartz diabase dykes, and one long olivine diabase dyke, the latest Precambrian rock. The area has been extensively glaciated.Structural FeaturesThere has been little folding in the area since the Algoman batholiths were intruded, and the Huronian sediments lie nearly flat, with dips of 10, 15, or rarely 25 degrees. The Matachewan dykes show a remarkably uniform, nearly north strike, indicative of east-west tension when they were intruded. On the other hand, the dykes later than the sill strike nearly east, tangentially to the northeasterly and northwesterly strikes of the Miller Lake basin."

Jan 1, 1949