Search Documents

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Commun¬ications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

The object of this paper is to give a description of the new office and changehouse building and equipment at the Zinc Corporation Limited, the office section of which has now been in full use for approximately three years, and the changehouse section for approximately two years. As the expectations of the design have been fully realized, it is thought that this description will be of interest to members and possibly of some use to others faced with similar problems.GENERALIn the centralization of the surface plant around the new main shaft the combined office and changehouse building forms a prominent feature, being located between the shaft and the mill and facing the workshops on the northern side.The scheme for housing all employees in one building was proposed by the Manager, Mr. A. J. Keast, who was familiar with a similar successful structure built at the McIntyre Porcupine Mines Ltd. in Ontario, Canada.The principal features of this building were adopted as a basis for design, and the present layout evolved to suit the particular requirements of this mine.Some of the advantages of the design are:(a) Economy in first cost and space occupied when compared with plants having separate office and changehouse buildings.(b) Easier and more constant supervision of employees and of the plant by the senior staff members.(c) Close contact between officials of all departments.(d) Close covered connection between changehouse and shaft.(e) Avoidance of duplication of ,essential services such as electric power, water, heating plant, sewerage, etc.The Managing Director, Mr. W. S. Robinson, further instructed that the following requirements be adhered to in the new building:(a) Ample accommodation to be provided for office staff and other employees.(b) Special attention to be paid to lighting, both natural and artificial.(c) Working temperatures to be controlled to facilitate comfort and efficiency.(d) The buildings and equipment' to be of a permanent nature with furnishings and fittings of modern design.

Jan 1, 1941

By P. I. Page

In mineral exploration the place that yields the first significant result is marked and two questions are posed immediately. Where should the next sample be drawn and how big should it be? At present the answers are arbitrary and ad hoc. They depend on personal experience and sentiment?that is hunch. The thought processes involved in reaching the decisions are unsatisfactory and unsatisfying for professionals. This paper proposes guidance on choosing sample spacing and sample size. The guidance is obtained from the grades of the samples. The grades also imply the extent of influence of each sample assay. Thus sampling and assay are integrated. The integration is achieved by changing the unit of value in which assays and grades are expressed and by exposing meanings and functions of grade beyond that of measuring rock value. The proposals are extended to guide comminution of particle size in sample size reduction and to deal with the problem of erratic high assays. Also, elucidation becomes possible of the computation of a reliable figure for average grade as a statistical weighted mean.

Jan 1, 2005

A typical sub-level block cave mining extraction method employs an undercut level to establish a cavity in hard rock, and as such requires special support methods and products to be installed during the development phase. The undercut level development in the block cave orebody is then sacrificial, and support elements will eventually report to the crusher and perhaps conveyor belt systems for transportation to surface. The choice of support products installed in the undercut level development should take cognizance of the detrimental effect these could have on the mining system such as cutting of conveyor belts, obstructing crushers, safety aspects, and productivity. This work explores the probability and practicality of making use of new-generation support products to make the operation safer as well as enhance productivity in the development phase and during the undercut operation. This paper will investigate the use of glass reinforced plastic(GRP) rockbolts and GRP mesh instead of conventional steel bolts and mesh along with resin capsule-filled holes with the GRP bolts. Complementing this with thin spray liner (TSL) application as another means of creating a safer operating environment, as well as a productive support medium, will also be addressed. These proposed items are envisaged to reduce production downtime and improve the safety of our people. These items are all easy and light to handle, cuttable and crusher friendly, as they will break up during the crushing process.

Jan 1, 2012

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules, under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and. tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment.

Jan 1, 1937

By Ron Tluczek

[Power Point Presentation]

Jan 1, 2006

By E. Henry, C. Mayer, H. Rott

Hangingwall deformation monitoring at Kiruna mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening toward the town of Kiruna. In the quest for more effective monitoring techniques, LKAB decided to evaluate the ability of satellite-borne synthetic aperture radar (SAR) interferometry to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the mining industry. This paper describes the basic principles of SAR interferometry and describes how subsidence is monitored at Kiruna mine. The encouraging results are discussed as well as the benefits (continuous deformation mapping, low cost, fast, etc.) and limitations (sensitivity to snow and vegetation cover) of the technique.

Jan 1, 2004

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

By André Laplante, Robert C. Dunne

"The role of flash flotation in precious metal recovery is reviewed. Interacting flash flotation and gravity recovery is discussed. The GRG test can be used, when linked to the behaviour of gold in grinding and classification units, to predict the recovery of GRG by flash flotation. The Cadia mill in New South Wales is used as a case study of circuit design, performance and simulation. It is shown that high throughput coarse grind applications such as Cadia require very effective fine GRG recovery systems in the primary grinding loop, which are more consistent with flash flotation than batch centrifuge concentrators (BCCs). BCCs can effectively recover a significant fraction of the GRG from flash concentrates, as predicted by laboratory testing and confirmed at a growing number of mill sites.INTRODUCTIONThe GRG test was designed to characterize Gravity Recoverable Gold (GRG) ten years ago (Woodcock and Laplante, 1993; Laplante et al, 2000), in response to the need to predict how much gold could be recovered from the main circulating load of grinding circuits using centrifuge concentration. The amount of GRG is not itself a prediction of gravity recovery: the performance of a gravity circuit nested in a circulating load also depends on the type and size of unit used, how much of the circulating load is treated, and how many times GRG is recycled and presented to the recovery circuit. The GRG test was first used in a simulator to predict gravity recovery (Laplante et al, 1995), and indeed most of the early tests targeted ores or prospective ores for which gravity recovery was an obvious match. As the test became more accepted, more and more samples returned a verdict that precluded the use of gravity recovery, or made it marginal. Typically, such ores are either copper-gold or base metal ores in which the GRG content is often fine (largely below 105 um) and ranges from 8 to 33%. Extensive simulation and plant sampling tests, either published (Laplante et al, 1997) or proprietary, show that full scale gravity recovery for these applications is generally below lo%, and can be as low as 2%. Not in all cases are such low recoveries economically unjustifiable, since there is documented evidence (Darnton et al, 1992) that a significant proportion of the gold recovered, at least in the case of base metal ores, would not have reported to the copper or zinc concentrate and received NSR credits."

Jan 1, 2002

By Steve Kral

Amax Coal Industries Inc.'s Delta Mine is a medium-sized. high-sulfur coal producer that has lived up to the challenges posed by nearly six decades of a highly competitive domestic coal market. The mine now faces one of its biggest challenges - the same one staring at the dozens of other high-sulfur producers in the Midwest - the Clean Air Act Amendments of 1990. The 59-year-old mine, located in the coal fields of southern Illinois, has remained one of the state's oldest continuously operating mines by rolling with the ups and downs of the coal market and by incorporating new technologies and innovative productivity improvements into its operation.

Jan 1, 1993

By J. Douglas, W. T. Ford, G. E. Henderson, I. F. Roebuck

An implicit numerical method is presented for simulating the differential and algebraic relations governing one-dimensional three-phase flow in porous media. The method is based upon compositional representation of the hydrocarbon system. Variable physical properties and water-oil capillary forces are included in the formulation; however, the effect of gravity is ignored. The effects of changing composition and mass transfer are considered through the use of known phase behavior concepts and correlations. The differential and algebraic equations and the numeric approximations to these equations are presented, and the computing algorithm is discussed in detail. This method is used to simulate a single-phase, two hydrocarbon-component gas displacement laboratory experiment. The method is also applied in simulating a solution gas drive and a gas injection problem using a reservoir oil represented as a nine-component mixture. For comparative purposes, the latter two problems also are examined with a one-dimensional volumetric model. The results of the simulation of the laboratory experiment demonstrate the relevance of this method to problems wherein the effects of mass transfer significantly enter the displacement process. The comparison of the results of the volumetric and compositional methods applied to a reservoir system illustrates not only the advantages and benefits derived from examining the hydrocarbon system composition, but also the necessity of this approach in application to a general reservoir problem. INTRODUCTION The advent of large memory, high-speed digital computers enabled reservoir engineers and mathematicians to pool their knowledge in the development of sophisticated techniques for the prediction of oil and gas reservoir performance. These techniques have progressed from volumetric and trend analysis calculations to the development of "mathematical models", or reservoir simulators. These latter models, in general, utilize finite difference approximations to the rather complex partial differential equations that mathematically describe the physics and thermodynamics of fluid flow in porous media. Many forms of this "model" type are available today, and much of the recent literature has been devoted to either improving known methods or developing new techniques for use in these prediction methods. The more advanced techniques in use at this time consist of the solution of differential and algebraic relations that describe a reservoir geometry in one, two or three dimensions and that incorporate reservoir hydrocarbon and water fluid systems that obey specified physical laws, having properties that might easily be measured in the laboratory. This type of model utilizes formation volume factors and other volumetric data, expressed directly as functions of pressure, to represent the reservoir fluid system. Experience gained with this type of simulator, commonly known as a "beta-factor model", has indicated that the approach has many outstanding defects, most of them due to the assumption that those properties measured in the laboratory completely describe the behavior of the fluid system throughout the life of the project under study. The effects of varying hydrocarbon composition and mass transfer between the phases of this hydrocarbon system must, by definition, be ignored. These defects, which may often be ignored in

Jan 1, 1970

By L. H. Banning

This investigation was undertaken to obtain basic information necessary for the design and operation of a plant for recovering metallic values from nickeliferous laterite and serpentine of the Philippine Islands. It was divided into three parts: (1) Mineralogical studies and preliminary mineral dressing tests; (2) electric smelting of the ores, upgrading of ferronickel by blowing with oxygen, smelting laterite slag to produce crude iron, and the production of mild steel; and (3) nickel and cobalt recovery from upgraded ferronickel. Results of the investigation indicate that it should be feasible to recover nickel, iron, and possibly cobalt products from the laterite and ferro-nickel from the serpentine. Mineralogical studies were made on representative fractions of the laterite and serpentine tonnage samples and on five selected samples; mineral dressing tests were made only on laterite. The nickel occurs principally associated with hydrous iron oxides and chemically combined with serpentine; garnierite was the only discrete nickel mineral identified, and it was found in a highly decomposed serpentine. The bulk of the cobalt was found in wadlike manganese oxide material. Approximately twice as much chromite was found in the laterite as in the serpentine, By mineral dressing techniques, laterite was separated into two fractions: one fraction contained over 90 percent of the nickel and cobalt, and 83 percent of the iron; the other fraction contained 74 percent of the chromium. A cobalt concentrate (1.1 percent Co) was produced by a scrubbing and sizing procedure.

Jan 1, 1962

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By Gale D. C, Giles D. E, James Parker A

A zinc-lead-iron sulphide concentrate from McArthur River can be leached at atmospheric pressure in aqueous solutions with HCI, FeCl3, CuCI2, HCl/02 HC1/02/ CuCI2, Cl2, and CI2/CuCI2 to extract >98 per cent zinc, >90 per cent silver, and <15 per cent iron in 1-7 h at 95°. Galena is more reactive than sphalerite and is converted to lead chloride. Except for leaching with HCI, elemental sulphur is the the main by-product of the leach with little or no sulphate ion detected. The rates and products of these reactions are compared. It is recommended that aqueous slurries of the concentrate (50 per cent w/v) are leached at atmospheric pressure with Cl2 in the presence of copper(II) chloride, which accelerates the extraction of zinc. Hydrochloric acid is a by-product which is consumed bYJeaction with fresh concentrate in air at 60°. Copper is subsequently stripped from the leach solution and recycled by reaction with fresh concentrate at 100°. The separation, recovery, and electrolysis of zinc and lead chloride is outlined since this process would produce Cl2 gas which can be recycled and used directly in the leaching stage.

Jan 1, 1976

By Jason M. Ryan

"Along with recent advances in computer technology have come cost-effective systems desiiedto evaluate fragmentation distributions through digital images of particles. In mining operations andmineral processing plants, important data from these systems is obtained through monitoring sizedistributions at key stages of the comminution process. Blast engineers apply this technology as atool for the validation of empirical fragmentation models so that predicted results are more meaningful."

Jan 1, 1998

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915