Search Documents

By Christopher Mark

Pillar recovery continues to be one of the more hazardous activities in underground coal mining. Safety requires that the roof above the intersection remain stable until after the pillar has been extracted. Artificial supports (timbers and Mobile Roof Supports) arc essential to roof stability, but so is the final remnant stump or pushout. Traditional mining practices usually called for the complete extraction of the final stump, but the recent trend (both in the U.S. and internationally) seems to be towards mining plans that leave a remnant stump. For this study, a sample of roof control plans from the Mine Health and Safety Administration (MSHA) Coal Districts were analyzed to determine current pillar recovery practices. Both full- and partial- extraction plans were included. Special attention was paid to whether plans require that a final stump be left, and whether requirements regarding the dimensions of the remnant stump are included. Foreign experience with final stumps is also summarized. It seems that the risk of major pillar falls can often be reduced by leaving final stumps that are large enough to protect the intersection, but small enough that they do not inhibit the caving of the gob. Because final stumps are often irregular in shape, a new approach for estimating their strength is described. Analyses were conducted to assess the effect of seam height and depth of cover on the potential variation in the size of remnant stumps.

Jan 1, 2001

By Todd M. Ruff

An average of 13 mine workers are killed each year by being run over or pinned by mobile mining equipment. At surface mines, these accidents commonly involve large dump trucks that drive over a smaller vehicle or a person that is in the dump truck’s blind spot. One method of detecting a person or another vehicle in a blind spot is to use some type of sensor technology such as radar or radio-frequency identification (RFID). Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health tested a number of commercially available and experimental sensors that monitor obstacles in a vehicle’s blind spots. None of the sensors had been previously applied to the specific problem of rigid-frame surface mining trucks. This report documents the procedures and results of tests conducted after RFID and radar systems were mounted on a 50-ton-capacity dump truck. It was determined that both RFID and radar technology show promise for detecting obstacles in the blind spots of mining equipment; however, more development work is needed to meet the unique requirements of mining equipment and the mine environment.

Jan 1, 2000

By Tim O’Neil

If you build a big truck, build a big tire to match it. Let that haulage synergy aid the economics, productivity and lessened maintenance for the unit. Now, Cater-pillar and Michelin have done just that. Discussions began in 1996. Caterpillar was making plans for its 797 ultra-class haul truck. The development team realized the need for a tire that could withstand extreme loads. The 797 would weigh 558 t (615 st) and be capable of 64 km/h (40 mph) speeds. So Caterpillar approached Michelin. The two companies realized the benefits of jointly developing a tire for the 797.

Jan 1, 2002

By K. E. Merklin, F. D. DeVaney

Students of the modern blast furnace seem unanimously agreed that they are observing a major revolution in practice. Rather than changing construction and operation of the furnaces, most of the great advances now under way deal with the raw materials feed. Prepared burdens have gained increasing significance during recent years. Sizing, concentration, and agglomeration have all become bywords to greater production and reduced operating costs. The remarkable results with test furnaces in which self-fluxing sinter makes up part or all of the ore charge foretell even greater improvements. Other investigators have reported many of these advances, and it is enough to predict here that more and more operators will turn to the use of self-fluxing sinter. This change in the operator's requirements comes at a time when one major section of the iron ore regions, the Mesabi, is finding it difficult to maintain, let alone improve, the tonnage and grade of its shipping product. To meet the new demands with respect to quality and structure, the iron ore producers of this area turned first to screening, crushing, and concentrating intermediate ores. More recently, declining higher-grade reserves have led to multimillion-dollar investments in plants to treat the low-grade magnetic taconites.1,2 To yield a suitable concentrate, the Minnesota magnetic taconites must be ground to about 80 pct through 325 mesh, too fine to be charged directly to the blast furnace or to make acceptable feed to the sinter strand. The pelletizing process was developed to meet the structure requirements laid down by the blast furnace operators. Taconite producers are succeeding in their efforts just when the attention of the blast furnace man is being drawn to the great advantages of self-fluxing sinter.3 The taconite operators are ready with an alternative. Why not produce sclf-flus ing pellets? At the Hibbing laboratory of Pickands Mather & Co., where much of the early work was done that led to Erie Mining's 7.5-million ton taconite plant at Hoyt Lakes, Minn., preliminary investigations have been made. Present Taconite Operations: Details of this work will be clarified by a brief review of agglomeration practice in commercial taconite plants. After the taconite has been ground to about 80 pct through 325 mesh to liberate the magnetite grains, the ore is concentrated on magnetic separators, thickened, and filtered to about 10 pct moisture. This structure and moisture fit in closely with the conditions required to produce good balls. It has been found with taconite concentrates that at least 60 pct of the feed to the balling drum must be —325 mesh to obtain good ball compaction within reasonable time. The filter cake moisture usually permits a slight water addition at the balling drum, and further balling control is obtained by adding about 12 Ib of bentonite and 1 1/2 lb of soda ash per dry short ton of concentrate. These additives, and occasionally small quantities of fine coal, are thoroughly mixed with the filter cake ahead of balling. The swelling property of bentonite improves the green and dry strength of the balls so they can be handled without breakage until they are fired. Soda ash is added for pH control to insure maximum performance of the bentonite, and coal is added for more heat in the firing process when required. The balls, normally 3/8 to l-in. diam, are brought to a temperature of 2350" to 2500°F in the indurating furnace. Heat for this process comes from three sources: 1) fuel burned in the combustion chamber, 2) oxidation of the magnetite concentrates to hematite, and 3) coal added to the balls. Pellet strength is developed by grain growth and bridging and, if enough slag-forming constituents are present, by slag bonding. Conversion to hematite is usually close to 100 pct in the fired pellets. Batch Test Procedures: Initial studies of self-fluxing pellets were made by producing balls on a batch basis under carefully controlled laboratory conditions. The l-in. balls, uniform in size, were fired in an oxidizing atmosphere in a standard laboratory muffle furnace. The firing procedure consisted of

Jan 1, 1961

By Douglas B. Silver

Traditional cycle theory would postulate that if you have a supply shortage relative to demand, the price will increase because buyers will incrementally increase the price they are willing to pay to ensure that their needs are fulfilled. As prices rise, more supply will be brought on and will eventually exceed demand. This supply excess will cause the price to decline as producers have to lower their prices to sell their goods. What is interesting is that cycles are simply volatility over time. Without the time factor, volatility simply goes up and down. When we add the time element, a cycle is created. This cycle can be big or small. In mining?s case, we are talking about a Super Cycle ? a big cycle. But a Su-per Cycle can be formed in two ways. It can form by either increasing the wavelength or the volatility. If these two elements are combined, a Super Cycle is formed. It is bigger than the normal cycle in terms of time duration and extent of volatility. A recent study (Fig. 1) conducted by Cuddington and Jarrett showed an interesting proof of Super Cycles and suggests that these cycles last between 15 and 30 years. So, what causes a Su-per Cycle? Is it a convergence of unrelated events or a consequence of related events? In a global community everything is related. Equilibrium theory would also take the position that a Super Cycle is a consequence of events.

Jan 1, 2008

By D. R. Brox, J. Levell

The Montana Tunnels Mine was mined out to a depth of 900 feet at the end of 1999. The first signs of instability were recognized in 1996 along the upper slope area of the northwest sector when the pit was mined out to a depth of approximately 500 feet. To extend the life of mining operations, it has been proposed to extend and steepen the northwest highwall to a depth of 1000 feet. Slope stability analyses were carried out using the UDEC software program to assess the stability and deformation of the proposed highwall design. Back analysis of an instability in 1997 along the upper slope section and highwall deformation to date has indicated reasonable agreement with the observed mode of failure and displacement monitoring results. The results of detailed analyses of the proposed highwall design have indicated very limited additional deformation, further development of tension cracks is unlikely and large-scale instability is not expected to occur. A total of 40% of additional mining has been completed and ongoing displacement monitoring to date has confirmed very limited additional movement and no further tension crack development.

Jan 1, 2001

By I. J. Brown

Paper prepared for presentation at Industrial minerals and the environment, held in Leeds, 24-35 September 1990. The need to submit an environmental statement (EIS) has certainly increased the workload of those concerned with both its production and assessment. However, there is now good evidence that the system is enhancing public confidence in the minerals industry in particular and improving relationships between the developer, planning authority and those consulted such as statutory bodies, parish councils, civic societies, nature conservation interests and ramblers

Jan 1, 1991

By A. P. N. Sutherland

Pipelines for transporting high concentration slurries are often designed using methods applicable to homogeneous non-Newtonian laminar flow. Many industrial slurries though comprise coarse particles in a non-Newtonian carrier fluid, and existing experimental evidence from tests with such slurries demonstrates that they are not homogeneous. Under laminar shear conditions the coarse particles settle, even in statically stable carrier fluids. To understand this better, the Institute of Materials Science and Technology (IMST) at Cape Peninsula University of Technology (CPUT) is conducting ongoing research into the flow of these high concentration non-Newtonian settling slurries. Since pressure gradient and flow rate measurements alone are insufficient to adequately model the flows, an electrical resistance tomography (ERT) instrument developed by the University of Cape Town (UCT)was incorporated into the pipe test loop to determine pipe cross-section concentration and velocity profiles. The software developed to do this is modular and allows different image reconstruction and cross-correlation algorithms to be implemented and tested without significantly changing the rest of the application. At a total frame capture rate of 566 frames/sec a 2.67 GHz Intel Celeron processor with 500 MB of RAM is fast enough to calculate and display velocity profiles in ?real-time? at an update rate of one profile every two seconds. Examples of experimental concentration and velocity profiles obtained using the system are shown and some proposed improvements/extensions to the system are listed.

Jan 1, 2008

By Gonzalo Chávez

El presente texto describe la lixiviación de oro con tiourea como una alternativa viable para la recuperación de dicho mineral, así como para el medio ambiente. En este sentido, la lixiviación de minerales de oro con solución ácida de tiourea fue evaluada con el uso de carbón activado, re-extracción y electrodeposición, obteniéndose velocidades de reacción y recuperación similares a los obtenidos con cianuro.

Sep 12, 2011

By Wilfrid Comeau

While researching for a theme lecture (Comeau, 1993l) on: 'The Mechanics and Physics Explosives', the author of Energy Transfer in Rock Fragmentaion by was confronted with many conflicting concepts regarding: the current explosive rock fragmentation theories, the physical principles governing energy transfers, the mechanical properties of rocks, and observations and data from full scale rock blasting.

Jan 1, 1995

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995

By J. P. Morris

An experimental blast furnace in normal operation was quenched by substituting cold nitrogen for the hot blast air. More than 2,200 samples from the stack, bosh, and hearth were taken; 500 of these were selected for detailed analysis. Deductions are made as to the patterns of burden movement and gas flow; the reduction of iron oxides, including a comparison of ore and sinter; and the behavior of sulfur above the smelting zone. Metal and slag beads from the bosh were analyzed, as were samples from the hearth metal and slag. A brief description of a petrographic examination of the quenched burden is included.

Jan 1, 1963

By T. A. Muhlare

The use of electrolyte additives to smoothen cathode deposits during copper deposition is practised worldwide. These additives absorb on the cathode surface and take part in the electrochemical crystallization process. However, these additives also affect the quality of the cathodes when they are inadequately controlled. Electrolyte additives used by Palabora are glue, thiourea, Avitone and chloride. Their effects were determined on cathode quality, the size of the current density region that gives the desired compact morphology, and current efficiency. This was done in a small-scale cell. Small cells have different hydrodynamics from industrial-scale cells, which makes it difficult to simulate the operation of industrial cells in a laboratory. The approach used here was to use a rotating cylinder cathode to attain controlled hydrodynamics. The rotation speed was chosen to give a diffusion layer thickness that is similar to that of an industrial-scale cell. It was shown that even fairly small changes in the additive levels can significantly affect the cathode morphology, and the current density range over which this morphology can be obtained. Keywords Copper, electrorefining, glue, thiourea, avitone and chloride.

Jan 1, 2011

By Pingchao Ke

A crystalline polyferric sulfate (PFS) adsorbent was synthesized by oxidizing and precipitating ferrous ions under atmospheric conditions. The morphology, structure, composition and specific surface area (SSA) and adsorptive efficacy to As (III) of the adsorbent were characterized by SEM/EDS and TEM images, XRD patterns, FT-IR spectra, BET SSA analyses and adsorption experiments. The adsorbent presents as morphology of near-spherical aggregate and good crystallinity. A small amount of goethite co-precipitated with PFS in the case of the initial ferrous concentration of 1 mol/L and increased the SSA of the aggregates. The absorbent with co-precipitation of goethite showed good adsorption to As(III) and good filtering performance in the high As(III)-content solution of 10–100 mg/L under acidic, neutral and alkaline conditions (pH 2.09–9.01), and its maximal adsorption capacity and adsorption efficiency were 7911 μg/g and 96% separately. After Adsorption, the stability of the absorbents adsorbing As(III) were evaluated by TCLP tests, and the results indicated that the absorbents adsorbing As(III) were extremely stable, and the concentration of arsenic in all leaching solutions were less than 0.01 mg/L.

By Stephen C. Tadolini, Anthony T. Iannacchione

"Coal burst represented a major hazard for some U.S. mining operations. This paper provides an historical review of the coal burst hazards, identifies the fundamental geological factors associated with these events, and discusses mechanisms that can be used to avoid their occurrences. Coal burst are not common in most underground mines. Their occurrence almost always has such dramatic consequences to a mining operation that changes in practice are required. Fundamental factors influencing coal burst events include strong strata, abnormal strata caving, elevated stresses, critical size pillars and the lack of sufficiently sized barrier pillars during extraction. These factors interact to produce excessive stress, seismic shock and loss of confinement mechanisms. Over the 90 years of dealing with these hazards, many novel prevention controls have been developed including novel mine designs and extraction sequences, most of which are site specific in their application. Without an accurate assessment of the fundamental factors that influence coal burst and knowledge of their mechanisms of occurrence, control techniques may be misapplied and risk inadequately mitigated. INTRODUCTIONCoal burst1are violent failures of ribs, roof or floor in underground mines. They are known to occur in complex ways and often under unique sets of conditions. This has made them extremely difficult to anticipate and control. Assessing coal burst risk requires engineers, managers, and safety professionals to recognize the fundamental factors responsible for these events. This helps practitioners recognize the hazard potential and understand the context in which various controls and barriers should be used. Only then can coal burst events be anticipated andappropriate mitigation techniques deployed.Over the last 90 years, a few coal burst events have been anticipated but most have eluded prediction. The authors examined the historical record (Appendix A) and determined that an inadequate understanding of the initiating geologic factors and their associated mechanisms of occurrence have contributed to the poor predictive capability. The historic record also indicates that control techniques have typically been site specific in their application."

Jan 1, 2015

Characterisation of Manganese Ores

Sep 13, 2010

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993