Search Documents

By M. A. Cook

Crude titanium metal, produced by the reduction of titanium tetrachloride with magnesium, is contaminated with some excess magnesium end adhering magnesium chloride when it is removed from the reaction pot. The method of vacuum 'purification is described in which the crude mixture is heated in a vacuum at a temperature of about 1,700° F. and the magnesium metal and chloride are volatilized away from the titanium, leaving it practically magnesium-free in a sponge-metal form. The pilot-plant equipment is described in detail, together with the technique of operation and methods of sponge recovery. Operating data is given, which compares ten 24- to 30-hour heats with ton 48-hour heats, and finally, power and labor requirements are discussed. Vacuum purification of raw titanium produced by the Kroll process has boon employed for treating of several tons of raw titanium with results for superior to those achieved by the method of leaching and grinding. The operations described, while on but little more than pilot-plant scale, indicate commercial feasibility of the process, even though it is a batch-typo operation. All equipment is either of standard manufacture or can be readily fabricated from standard materials, and operation of the units can be satisfactorily maintained by semiskilled labor.

Jan 1, 1952

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

Shortly after Denny, Robson, and Irwin published their first paper in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery.It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter's source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in:(1) Speakers on machine columns, vibrated by drills.(2) Vials placed in drill holes to be blasted.(3) Both homogeneous and heterogeneous mixture with explosives.(4) Packages with tamping.(5) Compressed-air lines.(6) Special compressed-air ejectors for use while drilling and after blasting.(7) The discharge of ventilation fans.(8) The filters of respirators.It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium p;wder, and would interfere unduly with underground routine.Later, animal experiments by Denny, Robson, and Irwin2 showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.APPARATUS USED IN THE DEVELOPMENT OF ALUMINIUM PROPHYLAXIS SAMPLINGA basic requirement was a method of sampling to assess accurately the particle-size concentrations of dispersed aluminium powder. Konimetry, though regularly practised at McIrityre, was inadequate for the research in mind. On the other hand, the efficiency of the thermal precipitator was recognized as being very high. Accordingly, the latter instrument was chosen as best suited to our needs. Through the courtesy of the Ontario...

Jan 1, 1945

By Alexander J. Verstraeten

Work started on the building of the Amsterdam Concert Hall in 1880 by driving over 2000 wooden piles of 13 m on which foundation-beams out of wood and brickwork were made. During construction the design was changed. This was due to the latest German developments, requiring double walls instead of single, so that the space in between could be used for ventilation and heating. Therefore the pile load, originally designed at approximately 100 kN, increased even to 170 kN for some piles, causing settlements and unacceptable cracks in the brickwork. Settlements of up to 18 cm were measured. In 1985/1986 around 400 vibration-free Tubex-displacement-piles were installed under the Concert Hall, with a shaft of 0355 mm, a pile shoe of 0560 mm and a pile length of approximately 18 m. After these Tubex piles had been installed they took over the complete weight of the whole building, thus eliminating further settlements and damage. 95% of all the construction activities took place while the concerts went on. The chosen solution also made it possible to create a new basement under the Concert Hall as an extension for dressing-rooms etc.

Jan 1, 1987

By D. S. Richards

Computers have revolutionized the collection of data on modern mines. Never before has it been possible to collect data from all aspects of the mining value chain at rates now common. With this has come a new challenge. Deriving information from these copious amounts of data and disseminating it. This problem is being exacerbated by technical software systems, which use proprietary and binary data formats that severely inhibit the flow of data and information both across departments and the larger organization. Generally this had led to data duplication and data redundancy. The Gemcom Enterprise Mining System (GEMS) makes use of industry standard, secure and open databases for all its data objects. It manages multiple users accessing the same bits and bytes in the database, preventing data duplication and redundancy. Developed in the Microsoft BackOffice ® environment, GEMS is also able to leverage the enormous amount of tools available in this environment, whether it’s for e-mail notification, reporting or data capture. Microsoft’s® Active Server Pages are one of these tools. These are standards used to create dynamic and interactive web pages with links into databases and many other objects. The real example outlined in the text, demonstrates how a user anywhere in the world is able to login to a web page and run a query that returns a report with vector plots of performance for the user-selected time frame. As integration is tightened between the various components of the mining value chain, the importance and reliance on ASP pages will grow as the need for management information tools develops. Keywords: mines, computers, ASP, GEMS, integration, Microsoft, Management Information.

Jan 1, 2003

Removal of As(III) and As(V) in Aqueous Solution There are toxic arsenical species such as As(III) and As(V), and arsenious species have specially strong toxicity. The strong toxicity causes contamination of groundwater and water pollution for the semiconductor production process. This study is concerned with the removal of As(III) and As(V) with various kinds of Mg/Al layered double hydroxides (LDH) containing CO32-, SO42-, Cl- and NO3- as interlayer anionic species. The anion exchange property is different from the kind of layered double hydroxides and the Mg-Al-NO3-LDH is superior in the anion exchange property of As(III) and As(V) due to the nature of nitrate ion existing in the interlayer. The pH condition suitable for As(V) removal is 7.1 or more. If the initial conditions such as 10mg/dm3 of As(V) concentration, 7.1 of pH, 1 m3 of amount of solution and 99 per cent of removal are fixed, the required amount of Mg-Al-NO3-LDH is 0.27kg for two step-batch operations. The As(III) is suitable to oxidize to As(V) before the removal processing.

Sep 13, 2010

By P. Dupeuble

Diaphragm walls, owing to their method of construction are discontinuous structures. A new technology for the construction of joints between panels has been developed. This new process allows for the construction of diaphragm walls with mechanical and watertight continuity.

Jan 1, 2010

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By J. L. Ellenberger, T. Miller

"A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor extensometers were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.To an area-wide failure (Zipf, 2001). In that case, it appears that the pillars had actually remained intact. However, moisture-related yield of the weak floor caused deformations which passed through pillars and into the roof, triggering roof collapse around the intact pillars (Esterhuizen et al., 2011). This previous case and the case presented in this study, while not identical, both demonstrate that weak floor and/or bands within pillars can be a significant factor leading to instability."

Jan 1, 2015

By Gerald M. Ellis

ntroduction As the gold mining industry continues to develop in the Dominican Republic and Haiti, more deposits will undoubtedly be discovered that will be amenable to development. The Pueblo Viejo gold mine is currently in operation in the Dominican Republic. It has become an important component of that country's economy. Pueblo Viejo output is important to the government as a foreign currency earner. It is also said to be among the world's more successful gold mines. But, while Pueblo Viejo is successful, no other major gold discoveries have been made in recent years. Therefore, alluvial deposits of gold have caught the attention of geologists on the Island of Hispaniola. In the past four years, exploration and investigation of alluvial deposits have been initiated in both the Dominican Republic and Haiti. This type of activity is expected to continue over the next few years. Alluvial gold mining is rudimentary gold washing, done mostly by farmers. It is an old tradition, dating back at least 100 years, and is done by small, independent, or community farming villages in the mountains and plains of the Dominican Republic. Investigations in the DR Recently, alluvial gold investigations have been undertaken in well known locations of the Dominican Republic. One is in the Villa Altagracia area. Here, the terraces and gravels of the Haina River basin were examined, test-pitted, and assayed by Minera Altagracia, a local Dominican mining group. Results led to a new investigation by the state-owned Rosario Dominicana (RD), the company that mines the gold at Pueblo Viejo. Rosario tested areas previously investigated by Minera Altagracia. RD could not define the type of concentration that could justify an industrial-scale type of exploitation. The Haina River placers are located in the flats and valleys of Central Dominican Republic. They are classified as small-scale type of operations where local cooperatives can do the traditional gold washing. It is not now considered a dredgable project for a mining company. The next alluvial gold investigation was undertaken by the Dominican Department of Mines and others in an area of some 700 km2 (270 sq miles) in the northeast near Miches. Farmers have been washing gold in streams and excavating pits in various areas, particularly La Mina and have made a living. Government geologists panned several hundred streams and river tributaries. They also washed material from deep excavations. The results, however, were negative insofar as locating alluvial gold concentrations suitable for large-scale or industrial-scale exploitation. The most favorable locations were the terraces along the Jayán and Cuarón Rivers in the area of Miches. But the grade od concentration is poor. Actually, only traces of gold were found in these

Jan 8, 1986

By Cliff McCartney, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research to evaluate and improve remote mine seal construction technology for mine fire control and suppression. The main focus of this work is to develop reliable technology that will remotely seal a mine opening from floor-to-roof and rib-to-rib. NIOSH, in partnership with Strata Mine Services Inc.1, is evaluating the capability of a two-component phenolic foam-based product, called Rocsil®1, that is intended for cavity filling, air and gas sealing, and consolidation of highly fractured strata. Rocsil® can be rapidly applied, has a quick cure time, a high expansion rate, good compressive resistance and excellent anti-static properties. When the resin and catalyst are mixed, an immediate foaming reaction occurs followed by rapid expansion up to 30 times the original volume. By virtue of its fire-resistance properties, Rocsil® foam has application for sealing underground mine areas undergoing heating from spontaneous combustion and it could be useful for remote mine seal construction to aid in mine fire control and suppression. This paper presents an overview of remote mine sealing technology, introduces the use of Rocsil® foam for remote mine seal installations, offers a case study of the use of this rigid foam material to remotely construct a temporary in-mine seal and discusses technology improvements. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

By C. Opoku-Ware, M. Kukay, P. Conrad

"This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 feet below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana. INTRODUCTION In an effort to improve Butte Area One natural resources, the research project was proposed to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU). Research by Blicker, et al. (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic VALUES ((Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown in an underground greenhouse located in the UMEC and will be planted in five areas located within the BPSOU designated for tree planting by the Butte Silver Bow government. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. They will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow."

Jan 1, 2018

By K. P. Fournier

This report describes work on the problem of predicting oil recovery from a reservoir into which water is injected at a temperature higher than the reservoir temperature, taking into account effects of vis cosity-ratio reduction, heat loss and thermal expansion. It includes the derivation of the equations involved, the finite difference equations used to solve the partial differential equation which models the system, and the results obtained using the IBM 1620 and 7090-1401 computers. Figures and tables show present results of this study of recovery as a function of reservoir thickness and injection rate. For a possible reservoir hot water flood in which 1,000 BWPD at 250F are injected, an additional 5 per cent recovery of oil in place in a swept 1,000-ft-radius reservoir is predicted after injection of one pore volume of water. INTRODUCTION The problem of predicting oil recovery from the injection of hot water has been discussed by several researchers. l-6,19 In no case has the problem of predicting heat losses been rigorously incorporated into the recovery and displacement calculation problem. Willman et al. describe an approximate method of such treatment. 1 The calculation of heat losses in a reservoir and the corresponding temperature distribution while injecting a hot fluid has been attempted by several authors.7'8 In this report a method is presented to numerically predict the oil displacement by hot water in a radial system, taking into account the heat losses to adjacent strata, changes in viscosity ratio with temperature and the thermal-expansion effect for both oil and water. DERIVATION OF BASIC EQUATIONS We start with the familiar Buckley-Leverettg equation for a radial system:* This is sometimes referred to as the Lagrangian form of the displacement equation. If the injection water is at some temperature Ti which is above reservoir temperature TR, then lw, the flowing fraction which is water, is a function of both water saturation and fluid temperature at any given time and position in the reservoir. The temperature dependence of lw results from the temperature dependence of the viscosity ratio µo/µm of which lw is a function. Thus:

Jan 1, 1966

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005

By Cathy Aimone-Martin, Brent Meins

A comprehensive instrumentation program was implemented at the Howland Hook Marine Terminal on Staten Island, NY during proximate underwater rock blasting in 2014. Forty-two blasts took place over a 4-week period to deepen the 1200-ft (366 m) Berth 3 from -45 ft (-14 m) to -50 ft (-15 m) MLW to accommodate Post-Panamax vessels. Approximately 86,000 yd3 (65,752 m3) were blasted 120 to 9 ft (37 to 2.7 m) from the wharf to a total depth of -57 ft (-17.4 m). Pre-blast planning included developing and implementing a comprehensive monitoring plan and setting vibration and strain limits to protect the wharf. The plan outlined methods to measure vibrations on five corners of four concrete deck sections, on five concrete-filled pipe piles just below the pile cap near deck corners, and in bedrock adjacent to pile sockets. Water overpressures were measured near instrumented piles for 19 blasts closest to the wharf. A total of 19 geophones were secured to the wharf structure and buried 12 ft (3.7 m) in drilled holes.

Jan 1, 2016

By G A. Challis, A B. Christiel

Microprobe analyses of electrum grains in some Hauraki Au-Ag deposits indicate that gold fineness is in the range of 500 - 800 (50 - 80 per cent Au), but for most deposits the range is usually narrower than this. The electrums contain minor amounts (<0.8 per cent) of copper, arsenic, antimony, mercury, iron, and sulphur. Platinum and palladium were analysed for but were not detected (detection limit 0.24 per cent for Pt or Pd). For some deposits (eg Waihi), the average fineness values for the analysed electrums correspond fairly well with the electrum fineness determined by assay during the historic mining operations.

Jan 1, 1992

By Je M. Oh

The U.S. Bureau of Mines is conducting research on the oxidation resistance and structural stability of Fe-(0-8)Cr-(0-16)Ni-(0-16)Mn-3.5Si-lAl alloys as potential substitutes for high-Cr stainless steels. Oxidation tests were conducted in air over the temperature range of 6000 to 9000 C for up to 1,000 h. Microstructures were analyzed at room temperature after hot rolling. The oxidation properties and the structural stability were found to be greatly affected by the Cr and Mn levels. Although substitution of Mn for Ni increased the oxidation rate, the Mn helped to stabilize the austenitic microstructure. Decreasing the Cr content or increasing the Mn content produced higher oxidation rates and earlier oxide spalling. In this study, reaction kinetics, oxide morphologies, and microstructure of the alloys were investigated using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and electron microprobe analysis.

Jan 1, 1989

This paper discusses the impacts that advances in metallurgy and process engineering have on minerals project execution. Ausenco's business is focused on integrating minerals processing technology and the delivery of cost effective processing plants that exceed client performance expectations. The metallurgical development is a small but critical part of this process. Metallurgical development and innovation outcomes need to be transformed into an engineered solution and that solution converted into an operating plant in a cost conscious and competitive environment. Including new or innovative processes in a project flow sheet increases a project's technical and commercial risk. However, it also gives the project, and/or the engineering company, a potential advantage over projects using mainline practices. Managing the balance between risk and opportunity has been a cornerstone of Ausenco's success in recent years. Some advances in "technology" that are discussed in the paper include: larger capacity equipment new flow sheet concepts simplification of process interfaces, and more effective project strategies The common theme is that having a new idea can be the easy bit, putting it into operation effectively involves numerous people, many interfaces and strong project management.

Sep 13, 2010

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013