Search Documents

By Marilia S. de Magalhaes

Keywords: sinter, characterization, agglomeration, iron ore Iron ore sinters are the main burden of blast furnaces for pig iron production. The evaluation of these agglomerates is very important due to their properties affect indirectly the productivity and costs of production of the steel industry. In the sintering plants, the standard procedure of sinter assessment has been carried out by particle size control, bulk chemical analyses, tumbler and/or shatter tests and determination of reduction degradation and reducibility indexes. Microscopy techniques have just been applied to characterize sinters produced in pilot conditions, however, these techniques, the classical ones and the less traditional, allow enhancing the industrial sintering process assessment. For investigation of the phases, microstructures and fabric, reflected-light and scanning electron microscopy(backscattered electrons images) were used; for micro analytical chemical examination, energy-dispersive X-ray spectrometry; for Kikuchi patterns registers, electron backscattering diffraction. In addition to the microscopy techniques, the magnetic behavior was depicted by means of magnetic susceptibility measurements. Iron ore sinters are made up by hematite, magnetite, silicoferrite of calcium and aluminium and silicates. These phases develop either during sintering or, in some proportion, represent remnants of ores and fluxes; this is the case of some hematite and Mg-bearing silicate, respectively. From the magnetic susceptibility results, three different behaviors were determined, which are directly related to the magnetiteproportion in the samples. The phase association and proportion, the sintering conditions andthe quality assessment are some features appraised by such procedures, which reveal themagnitude of this proposal in sintering plants.

Jan 1, 2005

By Joseph M. Kurtak

The U.S Bureau of Mines conducted a five-year mineral resource assessment of the 16.6 million acre Colville Mining District in northern Alaska, which includes part of the National Petroleum Reserve in Alaska. The study was initiated at the request of the Bureau of Land Management, which administers the majority of the region. The study was done in cooperation with the Alaskan Division of Geological and Geophysical Surveys, the U. S. Geological Survey, and the University of Alaska. During fieldwork, 1593 rock, soil, and stream sediment samples were collected and four bulk samples taken for beneficiation studies. A total of 40 mineral occurrences were documented, including 27 which were previously undescribed. No mining has occurred within the district. Mississippian carbonaceous shale and siliceous mudstone contain stratiform exhalative lead-zinc-silver occurrences. Grades average 8.0% combined lead/zinc and 51 gm/mt silver. Upper Devonian to Lower Mississippian sandstones host breccia veins, containing up to 29% combined lead/zinc and 274 gm/mt silver. Mineralized quartzites of similar age have potential for disseminated-type lead-zinc deposits. Samples from Lower Cretaceous mudstone and shale beds up to 6.5 meters thick, contain as much up to 12% manganese. Upper Mississippian carbonaceous shale and limestone beds contain up to 23% phosphate. Stratiform barite deposits hosted by cherts, are up to 27 meters thick with an average specific gravity of 4.16. Vein-type fluorite occurrences are associated with Mississippian limestone. Moderate potential exists for development of zinc -lead-silver, barite, and phosphate deposits.

Jan 1, 2011

By K H. Esbensen

The Theory of Sampling (TOS) has made remarkable strides and has witnessed a suite of achievements over its ~65-year history; especially in the last 15 years, since organised work began for the erstwhile fragmented sampling community (2003). Theory and practice have been very well exposed and disseminated, as witnessed in the successful series of the World Conference on Sampling and Blending (WCSB) events and other dedicated sampling and mining conferences in Australia and South Africa. At this WCSB8 occasion we fittingly devote a section of our conference to celebrate the life and monumental achievement of Pierre Gy, the originator of the Theory of Sampling; a special issue of TOS Forum was recently published to the same purpose. But TOS is most emphatically not a finished work.Here I try to look into the future with a personal view: TOS – what’s next? Commensurate with this objective there is offered some out-of-the-box thinking. The purpose is to try to zoom in on probable additional future aspects of TOS and its application compared to the first 15 years of our common journey. There are bound to be lacunae here-and-there across the vast application horizon delineated, which is as it should be, as this lecture is meant to initiate a broad(er) debate – and readers may agree with all, parts, or none of the topics presented. All is well that furthers this debate.CITATION:Esbensen, K H, 2017. Theory of Sampling – what’s next?, in Proceedings Eighth World Conference on Sampling and Blending , pp 29–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By G. R. Rawsthorne

"The Con-Rycon mine is located on the north shore of Great Slave Lake in the Northwest Territories within the present city limits of Yellow-knife. Development work on the Con property started in 1936, resulting in a mine-mill complex which produced its first gold brick on September 5, 1938. Since that date 5,000,000 tons of ore have been mined yielding 3,000,000 ounces of gold. At present there are 220 employees at the mine.MineThe mine has 1.22 miles of vertical shaft, 41 miles of level development and 10 miles of inclined raises. There has been 1,000,000 feet of diamond drilling in search of ore. The temperature at the 4900 level (4400 feet below sea level) is 68 deg. F.The present mining method is cut and fill. The majority of the ore mined today passed through an internal winze before reaching the main shaft. The long haulage and double handling will be eliminated with the completion of a new shaft presently under construction to the 5800 level.MineralizationThe ore treated today is from the Campbell shear 1vhich is characterized by lenses and veinlets of coarse textured quartz containing some carbonate, sulphides and finely disseminated as well as visible gold. At the lower levels of the mine the arsenopyrite content in the ore is de-creasing with a~ increase in the levels of chalcopyrite and pyrrhotite."

Jan 1, 1974

By D. E. Healy

In 1989, an autogenous grinding task force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding (SAG) at the National Steel Pellet Plant in Keewatin, MN. Pilot plant test work, performed by the Hanna Research Center (HRC), indicated that fully autogenous grinding with pebble extraction and crushing could be incorporated into the existing circuits. In 1990, one of the existing 10 grinding mills was converted for an in-plant test incorporating pebble crushing. Full-scale test work were conducted in 1990 and 1991. They verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit using pebble crushing being greater than throughput of the existing SAG mill circuits. The plant produces 5 Mt/a (4.9 million ltpy) of iron ore pellets from 17.6 Mt (17.3 million It) of crude taconite. Crude ore is single-stage crushed by gyratory crushers. Primary grinding is performed by 10 semi-autogenous wet grinding mills. Secondary grinding is performed by five ball mills. Induration is with an Allis Chalmers grate-kiln pelletizing system. The primary grinding circuit consists of 108.2-m-diam x 5.5-m long (27 ft-diam x 18-ft) SAG mills. The mills are charged with 127 mm-diam (5 in.diam) steel grinding balls at from 3% to 5% by volume. Ball consumption rate is about 0.55 kg/t (1.25 lbs/lt) of crude ore feed to the mill. Each SAG mill is powered by two 2.6 MW (3500 hp) motors drawing 5450 kW (7300 hp) at 76% of critical speed. The mills are grate discharge with 16 mm (0.6 in.) slotted grate openings when new. The mill discharge is sized on a trommel screen having 4.5 mm (0.2 in.) openings. The plus 4.5 mm (+0.2 in.) oversize material is returned to the discharge end of the mill by a reverse screw auger located in the center of the trommel. The -4.5 mm (-0.2 in.) trommel screen undersize is pumped to magnetic cobbers.

Jan 1, 1992

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

By K. Adham, C. Lee

Over the last forty years, a number of specific fluidized bed applications in nickel extraction have been developed for commercial use. Five important processes have gained particular acceptance, namely, sulphide ore roasting, nickel sulphide (matte) roasting, nickel oxide reduction, laterite ore pre-reduction, and nickel chloride pyrohydrolysis. These applications involve different feed materials and process conditions, however, all benefit from fast reaction kinetics and high heat and mass transfer rates in the fluidized bed reactors. They have been studied, tested, and implemented by various nickel producers, who have published their results in many papers and patents. This paper examines the design issues surrounding the application of fluidized bed technology to the above nickel processes. Based on the available data in the open literature, computerized process modelling is used to provide generic flowsheets that illustrate the key features of each process.

Jan 1, 2004

By J Ward, B Rohrlach, B Rosero, J Silva, O Poma

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Alpala copper-gold deposit is a recent, high-grade porphyry Cu-Au discovery located in the Imbabura Province of north-western Ecuador. The deposit lies along the crustal-scale Chimbo-Toachi Fault Zone within the Dagua-Piñon terrane, which is an oceanic plateau accreted to the South American convergent margin in the Late Cretaceous. The deposit is hosted by quartz diorite stocks that intrude andesitic volcanic breccias of the Oligocene to mid-Miocene San Juan de Lachas Formation. Miocene-age calc-alkaline plutonism is associated with porphyry Cu, Cu-Mo and Cu-Au deposits in southern and northern Ecuador. The Alpala deposit lies along a sector of the Miocene arc that has recently been underplated by the Carnegie Ridge seamount chain that induced shoaling of the subducted Nazca plate beneath northern Ecuador.Surface expressions of the deposit were recognised in May 2012 during follow-up of stream sediment anomalies, when outcropping sheeted and stockwork porphyry-related veins were discovered in Quebrada Alpala. The roots of a NW-trending, structurally-controlled lithocap were recognised over an area of 4.5 × 0.9 km. The remnant lithocap exhibits well-defined mineral zonation mapped by TerraSpecTM analyses on grid soil samples. Soil sampling, heliborne magnetic surveying and channel sampling defined initial drill targets.Seven diamond drill holes were completed in the year from September 2013. Drill hole CSD-13-005 intersected 672 m grading 0.93 per cent Cu and 0.91 g/t Au in high-temperature, inner propylitic and locally potassic-altered quartz diorite intrusions. Overlying hydrothermal clay alteration assemblages define the base of the lithocap. A NW–SE trending footwall structure defines the south-west margin of the deposit. Drill hole 5 intersected high-grade sheeted ‘B-type’ and ‘C-type’ veins (Gustafson and Hunt, 1975) that lie along the south-west margin of an 1100 × 500 m magnetic anomaly that is the focus of ongoing exploration.CITATION:Rohrlach, B, Poma, O, Rosero, B, Silva, J and Ward, J, 2015. High-grade porphyry copper-gold mineralisation in north-west Ecuador – The Alpala Cu-Au porphyry discovery , in Proceedings PACRIM 2015 Congress, pp 369–376 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D. G. Eskin

"It is well known that it takes some time for the solid phase to completely dissolve upon melting, especially inside the defects of insoluble particles, e.g. oxides. Until then the oxides remain active solidification substrates in the case of subsequent solidification. It is also known that ultrasonic melt treatment causes grain refinement through activation and dispersion of solidification substrates (one of the mechanisms) and also accelerates the dissolution of solid metal in the melt. In this study we combine these effects and demonstrate that the introduction of an alloy rod into the matrix melt of the same composition results in significant grain refinement, this effect being increased by the ultrasonic vibration of the rod. The achieved grain size is comparable to that obtained by a standard Al–Ti–B grain refiner. All samples were cast using a standard TP-1 mould to enable correct comparison. The effect of the temperature range of the rod introduction, as well as the effect of ultrasonic vibrations are discussed.INTRODUCTION The fact that by introducing solid metal into the melt one can achieve structure refinement is rather well known. As early as in the 1930s–1950s a series of papers and patents have been published, showing the benefits for grain refinement when dissolving solid metal in the melt before solidification (Danilov and Neimark, 1938; Scheil, 1956). Later on this way of structure refinement was developed further and dubbed “suspension casting” or introduction of “internal chills” (Madyanov, 1969; Zatulovsky, 1981). The solid metal was added in a form of cut wire, cut sheet, or powder, with the resulting grain refining, elimination of columnar grain structure in ingots and castings of steel, copper and aluminium alloys. The underlying mechanisms have been suggested as (1) rapid cooling of the melt due to the latent heat consumption upon melting of the solid metal with the resultant melt undercooling and (2) introduction of many solidification substrates in the form of crystal fragments and active non-metallic inclusions (Danilov & Neimark, 1938; Balandin, 1973). A number of patents have been filed where either the same solid alloy or a master alloy with additions (e.g. Ti for Al alloy) is introduced in the amounts up to 50% (typically less than 10%) into the melt close to the liquidus temperature (Schmidt, 1966; Talbot & Soller, 1973, Krupp, 1974; Bondarev, 1979). The main reason that this technique is not widely used in industry is the possible incomplete dissolution of the solid parts introduced into the melt with ensuing inhomogeneous as-cast structure and potential defects. Also the selection of the temperature range where the technology works the best is not clear."

Jan 1, 2018

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nonmetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By E. T. Turkdogan

Jan 1, 1962

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U.S. Department of the Interior, to give greater impetus to the building of programs safeguarding the employees of the mineral industries from disabling work injuries. The results of the 1960 National Safety Competition are presented in this publication. Mines and quarries that were awarded the Sentinels of Safety trophy for the best safety record in their competitive group and those mineral operations that ranked second, third, fourth, and fifth in the competition are listed with a summary of their achievements in preventing disabling work injuries. In addition, this publication presents statistical data on disabling work-injury experience in all other mines and quarries participating in the annual competitions.

Jan 1, 1962

By Dale S. Preece

"Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control. Three-dimensional computational capabilities in terms of software, material models and computer speed have recently made possible the computer simulation of multiple blast holes in a bench configuration with precise delay timing between holes. Some of the key physical phenomena enabled by precise delay timing include: 1) collision and interaction of stress waves produced by adjacent blast holes, 2) reinforcement of stress waves from multiple holes as they reflect from the bench face and ground surface, 3) reflection of stress waves from “dynamic free surfaces” created by previously detonating holes, and 4) deformation induced fracturing, cracking and fragmentation. Simulating rock blasting in 3D has shed light on the physics involved and is resulting in an evolution of our understanding of fragmentation mechanisms. Routine use of these 3D computational tools will result in a much better understanding of the complex physics set in motion by the rock blasting process and allow predictionof improved blasting."

Jan 1, 2009

By K. Meyer

"INTRODUCTIONThe David Bell Mine Concentrator started production in April 1985. A staff of twenty-seven people operate and maintain the concentrator. The crew is grouped into the following main areas.16 Operators6 Assaying/Metallurgy/Refining/Clerical4 Maintenance people2 SupervisionOperating highlights of the following unit processes will be discussed in detail:Screening and ThickeningPre-aeration and CyanidationCarbon-In-Pulp Gold AdsorptionCarbon Handling andGold RecoveryFor a complete description of the concentrator, refer to the papers by: (1) C.V. Sibbald, Teck-Corona's Hemlo Mill, October 1984, (2) R.A. Ford, The David Bell Mine at Hemlo, From Exploration to Production, November 1987. For operating details of the grinding circuit and effluent treatment plant refer to papers by: (3) T.G. Smith, SAG Mill Experience at The David Bell Mine, October 1988, ( 4) AN. Veltmeyer, The Effluent Treatment Plant of The David Bell Mine, January 1989.TRASH AND CARBON SCREENSTrash ScreenThe vibrating trash screen is inclined at 5 degrees and is clad with a 28 mesh stainless steel cloth which is changed monthly during the SAG mill liner replacement/inspection shut down. Other screen openings and configurations have been tried and the screen has been by-passed to change the cloth ""on the fly"". These attempts resulted in fibres (usually wood) to report to #1 Carbon-In-Pulp (CIP) tank, where the fibres are trapped in the CIP launder screens, and downstream carbon handling screens causing serious blinding problems. The trash screen in a Carbon-In-Pulp (CIP) or Carbon-In-Leach (CIL) gold mill removes fibres before they:are reground in the ball millsaturate with gold bearing leach solutionplug launder screens in CIP or CIL tanksplug carbon circuit pipe screenstherefore the trash screen is best placed ahead of the thickener."

Jan 1, 1989

By B. Genc

After the explosion at Middelbult Colliery, South Africa in May1993, which claimed 53 lives, the South African Coal Mining Industry and the Safety In Mines Research Advisory Committee (SIMRAC) united forces to establish a surface facility to develop and test on-board flame suppression systems for continuous miners and roadheaders. The first test that was conducted in this newly constructed test tunnel at the Kloppersbos Research Facility, CSIR was in July 1995.Since then 70 tests have been conducted using the facility and have focused on on-board active ignition suppression systems for continuous miners (CM) and road heading (RH) machines to enhance the safety of South African mine workers in collieries. These suppression systems are mounted on the CM or RH machine and detect the occurrence of an ignition by means of light-sensitive sensors. The electronic signal from the sensor triggers the suppression system, creating a flame-suppression curtain, containing and extinguishing the flame in the immediate vicinity of the ignition. Forty-three tests have been conducted with an active on-board suppression system present inside the test tunnel. Since flame propagation speed is an extremely important parameter, the CSIR-Miningtek made the results of the test programme available for re-analysis. Flame speed depended on whether a machine was present in the heading or not, the geometry of the heading and the volume and composition of the explosive mixture of gas. Flame speeds of up to 190 m/s were recorded. However, the active suppression systems were almost always successful in containing flame propagation.

Jan 1, 2002

By Thomas J. Witzig

This Bureau of Mines report is a background study of the International Tin Agreement. Attempts at stabilizing the tin market prior to the agreement are detailed, as well as the conditions and negotiations that set up the agreement. Details of the five consecutive 5-year agreements beginning in 1956 are presented, with emphasis on membership and the agreements' primary tools: the buffer stock and export controls, Attention is focused throughout on the United States activities during the period, especially with regard to its strategic stockpile, and its involvement with the agreement culminating in its membership, for the first time, in the fifth agreement beginning in 1976. Considerations leading to the U.S. decision to join are detailed, and U.S. activities in the negotiations for the sixth agreement are presented. The status and outlook for the agreement are discussed, and evaluations of the effectiveness of the agreement and its components are reviewed.

Jan 1, 1981

Validation and Simulation of Optimised Compressive Crushing Ores and aggregates are used in countless applications all around in the society. The frequent and escalating usage of these natural resources requires efforts aimed at not only making do with what is available, but also undertaking actions to improve the production yield and the processes involved. This strive to improve the performance and efficiency of existing crushers and crushing processes has brought about research concerning optimisation of crushing plants as well as theoretical optimisation of crushing. Previous work shows that different applications and different materials require different compressive crushing in order to accomplish a theoretically optimal size distribution. These optimisation results, obtained by genetic evolutionary algorithms and evaluated with so called fitness functions, convey the theoretically optimal number of compressions and their corresponding compression ratios. Presented in this paper are thus some laboratory crushing tests, which are conducted in order to validate a set of previously optimised crushing sequences. More specifically, interparticle crushing sequences are carried out in a Piston-die testing equipment, where samples are sieved between each compression. The subsequent analysis of these results shows good correlation with model predictions, which combined with a comparative study between presented optimisation results and measured data from a real crusher indicate a significant potential for improvement. However, before redesigning crushers according to what is theoretically optimal, the resulting impact as well as the effects on the outcome of a crushing plant must be examined. Crushing plant simulations using the software PlantDesigner« are consequently performed. Models of existing crushers are altered, resulting in changed particle size distributions from some of the crushers in a crushing plant. Thence, it is concluded that significant gains can be made in terms of capacity, process yield and energy consumption.

Sep 13, 2010

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974