Search Documents

By W. Joseph Schlitt, William D. Southard, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12 - 15% moisture could be consistently delivered for smelting.

Jan 6, 1979

By J. `. Spitzinger

In situ recovery (ISR) of uranium alters the baseline groundwater geochemistry in order to mobilize and complex uranium to extract and concentrate it. ISR wellfield restoration is often challenging, and primarily relies on groundwater sweep, reinjection of treated permeate, and/or injection of reductants. Greater focus should be placed on injection-based approaches (using existing infrastructure) based on established engineering concepts used for in situ remediation of groundwater plumes. Such injection-based approaches could shorten restoration timeframes consequently reducing long-term operational costs. This paper addresses various types of injection-based approaches to wellfield restoration based on in-situ remediation success with other constituents that require similar treatment. This paper describes necessary design practices for injecting reactive chemicals (e.g., reductants or biostimulants), operations and maintenance (O&M) strategies to prevent fouling of the chemical delivery system and well network, and natural constraints to restoration. Best practices for successful biostimulation strategies that minimize residual uranium, radium, oxoanions, and other trace elements are as described. Advantages of such injection-based approaches could include significant reductions in restoration times, and consequently, lower restoration costs.

Feb 23, 2014

By A. R. Naderian

Laboratory strength and deformation testing of freshly blasted sandstone and claystone overburden from Jeebropilly colliery in Queensland and in-situ plate-bearing tests on four backfills of different ages showed that the bearing capacity of backfill is a function mainly of compaction, not of age. The modulus or stiffness of the backfill is significantly increased by previous loading, in some cases up to threefold. Backfill material experiences some compaction through the passage of mining vehicles, likely to provide a bearing capacity that will support normal construction activities; the limited testing performed suggested that completed backfills are capable of supporting loads of up to 200 kN/m2 while sustaining displacements acceptable for a wide range of residential and industrial uses, but may be susceptible to collapse settlements due to saturation in the long term

Jun 19, 1905

By Natalya. N. Ankusheva

The problems of ore-bearing palaevolcanic structures in folded belts are actual because of their high productivity in nonferrous, ferrous and noble metals ores. Now relationships of location and conditions of formation for sulfide-massive and gold-bearing deposits are investigated very well in Urals. But carboniferous sulfide-barite mineralization, for example the barite veins in Arcaimsky palaevolcano are?nt studied enough now [3-5]. The purpose of this research is the studying of mineralogy and thermobarogeochemistry of barite from the hydrothermal veins. It will allow to determine the conditions of its formation and to compare it to the similar mineralization of others ore types.

Jan 1, 2006

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit, in Yemen, contains at least 9.4 Mt at a grade of 10.7% zinc, 2.2% lead and 77g/t silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to conventional smelter/refineries, and it has been necessary to formulate a less conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material, at Yanbu, in Saudi Arabia. In order to give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulphide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, the flowsheet for Yanbu and presents preliminary costs for both operations

Jan 1, 2002

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946

By K. J. Stanaway

Major world ilmenite and rutile accumulations reveal similar regional geology and Proterozoic age deeper crustal source rocks. During crustal collision titanium crystallizes as ilmenite and rutile at buried sites of high pressure and temperature rock metamorphism. Hydrothermal activity can convert titanium minerals to rutile, but titanium migration and enrichment seem only local. Many melts crystallize rocks with iron-titanium oxides in solid solution, but titanium enrichment at economic scale takes place in basic intrusive melts often associated with anorthosites and charnokite. Sedimentary placer enrichments have formed since the Proterozoic with water-resistant ilmenite, and rutile segregating by gravity from quartz sands deposited from flowing water. Placers have residual, alluvial, strand and shallow marine variants. Time, organic acids, and sand permeability play lead roles in the leaching of iron from ilmenite during weathering and diagenesis.

Jan 1, 2005

By Leonard Obert

THIS REPORT presents methods and principles useful in designing underground mine openings and pillars in competent rock formations. Two types of formations are considered: (1) Massive formations, in which openings are generally mined with an arched roof, and (2) bedded formations, in which openings are generally mined with a flat roof. Design principles for openings and pillars in massive formations are obtained by considering the maximum tangential stresses developed around single and multiple openings for stress fields of various types. Design principles for openings and pillars in bedded formations are obtained by considering the average stress in pillars and the maximum stresses in roof layers. Experimental procedures for making stress, strain, and in situ physical-property measurements in underground mines to check design calculations are outlined and the results discussed.

Jan 1, 1960

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By Erwin L. Zodrow

"The neglect of including the toxic metal mercury in the list of escaping elements (Zodrow, CIM Bulletin, September 1982, pp. 138-140) was pointed out to the author in a private letter by J.E. Rehder, dated September 21, 1982. I welcome this opportunity to present my preliminary mercury research data based on coal investigations supported by N.S.E.R.C and the University College.As mercury is a volatile element and liquid at room temperature, special analytical techniques are required to determine concentrations in whole coal. In the investigation, the coal is analyzed by flameless atomic absorption with a lower detection limit of approximately 10 parts per billion, which, however, is a function of the ash contents of the coals (personal communication, J.L. Brooker, XRAL, 1981).Coal seams of the Sydney Coalfield studied so far include: the Point Aconi, a thin shaly coal, the Upper Bonar, an overrider of the Harbour seam, and the Harbour, Shoemaker and McAulay seams, all of which are shown in stratigraphic succession in Figure 1. The seams have been channel-sampled taking 15-cm coal intervals as one sample for analysis. One channel sample has been investigated from each of the seams listed (two channels were taken from the Point Aconi seam), resulting in 38 samples. Table 1 shows the results, which include mercury contents, ash and total sulphur per sample interval. Figure 2 is a frequency distribution of the 38 determinations."

Jan 1, 1982

By Collin L. Stewart

The high cost and limited flexibility of modern longwall systems has resulted in the need for mine engineers and geologists to predict possible adverse mining areas ahead of mining and to then design and implement suitable ground control solutions in a timely and cost effective manner. Therefore, over the last 30 years, geo-technical evaluations for coal mine planning and development have advanced from a minor afterthought to an important part of today?s successful, high capacity, longwall mining operations. The latest iteration in this progression of improved analysis for predicting future mining conditions is a computer-based Stability Mapping System developed by West Virginia University. This system is designed to allow the mining engineer and geologist to effectively combine the mine geologic characteristics, stress influences, and structural features into an integrated stability map for use in mine planning and support design. This paper details the application of the stability mapping system to Bowie Resources, LLC, Bowie No. 3, multiple-seam longwall coal mine. At this mine, the prediction of adverse mining conditions using the stability mapping system allowed management to accurately adjust their support densities and operational procedures, and to successfully mine through difficult conditions safely and successfully.

Jan 1, 2006

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940 to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the? Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940, to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Rayner J. G, Leckie J. F, Moorehead C. F

The Coronation Hill gold-platinum-palladium prospect is located in the valley of the South Alligator River (latitude 13'35'S, longitude 132'36'E), about 80 kilometres east of Pine Creek in the Northern Territory. Coronation Hill was one of thirteen sites in the South Alligator Valley at which uranium was mined between 1955 and 1964 after initial discovery by the Bureau of Mineral Resources in 1953. Most of the mines were operated by United Uranium No Liability. The Sleisbeck mine 25 kilometres south of Coronation Hill was operated by North Australian Uranium Corporation and the group of mines at Rockhole about 20 kilometres to the north-west of Coronation Hill was operated by South Alligator Uranium No Liability. The uranium mine at Coronation Hill produced about 26000 tonnes of ore averaging 2.6 kg/t U308 with an estimated average gold grade of 10.4 g/ gold. Gold was commonly associated with the uranium mineralisation and was recovered at the gravity treatment plant at El Sherana. Gold was also recovered in 1986 by Pacific Gold Mines Limited by treating the tailings from the Moline and Rockhole uranium leach plants at a CIP plant at Moline. With the completion of uranium contracts in 1964 mining in the South Alligator Valley ceased. Exploration for uranium continued in the area during the 1960s and 1970s with no success. The Coronation Hill Joint Venture (BHP Gold Mines Limited 45 per cent, Pioneer Minerals (Gold) Pry Ltd 45 per cent, Notgold Limited 10 per cent)carried out the first exploration specifically targetted at gold in 1984 with the drilling of five vertical drill holes which indicated high potential for a substantial gold resource at Coronation Hill with no associated uranium. The Joint Venture has sub- sequently drilled about 25000 metres of diamond drill holes at Coronation Hill alone. Analytical results from 1985 drilling established that platinum and palladium were associated with gold. An indicated resource of 3.49Mt at 5.12g/t Au, 0.21g/t Pt and 0.56g/t Pd has been calculated using a lg/t Au cut off.

Jan 1, 1991

By E. A. Schmidt

In 1962, while investigating the tungsten potential in the Thompson Creek area for Union Carbide Corp., Henry T. Eyrich obtained anomalous concentrations of molybdenum (up to 19 ppm Mo) from stream sediment samples collected along Pat Hughes Creek, a tributary to Thompson Creek. Follow-up investigations by Eyrich during the same year disclosed the presence of a hydrothermally altered and molybdenite-bearing granitic exposure in the headwaters of Pat Hughes Creek about 2.4 km (1.5 miles) upstream from the sample point. The altered outcrop measured about 549 by 305 m (1800 by 1000 ft), contained abundant northwest-trending quartz veins locally with molybdenite, and was overlain and surrounded by the Challis volcanic extrusive sequence of mid-Tertiary age. Eyrich's subsequent soil and rock chip geochemical sampling program over the altered outcrop area showed a general increase in the molybdenum content to the northwest toward the postmineral Challis volcanic cover. Over a distance of about 305 m (1000 ft), values in the altered intrusive rock increased from less than 5 ppm Mo to over 600 ppm Mo, with aconcomitant intensity of the hydrothermal alteration pattern. Based on these geochemical results and on preliminar; megascopic hydrothermal alteration studies, Eyrich correctly concluded that the altered outcrop is an erosional window and that molybdenum mineralization of sufficient grade could exist beneath the Challis volcanic cover some distance further to the northwest. His recommendation to test the area of potential molybdenum mineralization with several drill holes was, however, declined by Union Carbide in 1962. The property remained unclaimed until 1967, when Eyrich joined Cyprus Mines Corp. Acting on Eyrich's recommendation, Cyprus immediately staked 26 lode mining claims to cover not only the altered intrusive outcrop, but also the northwest trend of mineralization where it projected beneath Challis volcanic rocks. Eleven of these claims are now patented.

Jan 1, 1991

By N. A. C. Smith

The Bureau of Mines motor gasoline surveys have been conducted in January and July, during 1920 and 1921. The Bureau has obtained and analyzed samples of gasoline representative of that marketed in the larger cities. These surveys have indicated that the gasoline on the market during the winter months is more volatile than that sold during the summer months. Naturally, the motorist desires a more volatile gasoline in the cold winter months, as it affords greater ease in starting. The fourth semi-annual motor gasoline survey, conducted during the month of July, shows an interesting relation between the market price and the quality of motor gasoline. This is particularly evident if figures obtained today are compared with those of a year ago. At the time the Bureau of Mines conducted its summer survey of motor gasoline last year, the average tank wagon price of gasoline was 28.2 cents per gallon. This year it was 21.2 cents, a drop of practically 25%.

Jan 1, 1921

In today?s high tech world, systems are getting bigger, faster, better. To remain at the leading edge, in any business, depends on accurate but flexible design thereby allowing operational managers to provide alternatives to improve their operations. The ultimate goal is to deliver to plan, with optimum economics. Mining is no different, with falling prices and escalating costs, improved margins become the focal objective. There are many ways to achieve this, ranging from operational efficiency improvements through production scenarios to planning initiatives. Of all, planning usually receives the least attention, yet it is the area of most influence on the NPV of the reserve. With computer technology, numerous concepts and iterations are possible thereby closing the gap between optimal and actual design. This paper discusses the application of the split shell design at the De Beers Venetia open pit in South Africa.

Jan 1, 2001

By Claude MacDonald, John H. Ashburn

"IntroductionIndustrial growth and technological change over recent years had been accompanied by two major sources of concern to management and employees: (a) increase in occupational injury and illness and the resultant costs involved; and (b) equipment damage and breakdowns in concentrated production lines causing more extensive loss potential.Due to economic factors, management attention has focussed more on production and quality than on safety, health and related loss potential sources. As a result , occupational safety and health activism has grown, government legislation of compensation and occupational safety and health standards have progressively developed and stronger liability attitudes have been taken by courts of law.To improve efficiency and allow development in more competitive markets, rising labour costs, equipment costs and safety related financial losses have dictated that attention be given to conservation of all resources. Conservation of resources, people, equipment, material and environment, can no longer be addressed in isolation but must be managed integrally with production and quality. To this end, systems have developed utilizing sound management principles applied with equal intensity to production, quality and loss potential"

Jan 1, 1987