Search Documents

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By John Wilson

"The Rietveld numerical method was used to calculate the relative abundances of phases in both synthetic binary mixtures and synthetic and natural ores, using X-ray diffraction data. The results were compared with those of image analysis and a chemical method. The ranges of the relative errors were estimated. The Rietveld method is found to be acceptable for determining the abundances of major and minor phases and the amorphous component of partially crystalline samples. In complex mixtures, where there are several trace phases (~<2 wt%) present, the technique becomes less accurate. It is most useful as an alternative technique to image analysis when sample preparation is problematic or sample particle sizes are sub-micron. It is a manual method which requires user input during the fitting process, but is both simpler and faster than image analysis due to the reduced set up time and sample preparation required. It is now implemented at CANMET as a technique for quantitative analysis.INTRODUCTIONUntil recently, the Applied Mineralogy group at CANMET used only image analysis and chemical techniques to determine phase quantities. An effort to develop quantitative X-ray diffraction (XRD) has been on-going for several years. Initially, the reference intensity ratio (RIR) method with external standards was tried with some success (Szymanski and Petruk, 1989). The main difficulty with this technique was finding adequate standard material for each phase present in the sample. This shortcoming made the method ultimately impractical, given the wide variety of materials which come to the laboratory for analysis.The Rietveld refinement method of quantitative XRD (Hill et al 1993, Mumme et al 1996), in contrast, requires no standards and requires minimal sample preparation and therefore a more rapid turnaround compared to image analysis. The Rietveld method also has advantages over image analysis in that it can identify and quantify polymorphs, ultra fine materials and many types of hydroxide products. As well, it is useful for analyzing materials such as bauxite or talc, which do not polish well enough for making mounts of the quality required for image analysis. To quantify amorphous material and phases which are present in amounts below the detection limit of XRD, the addition of a standard material is still required. However, in such cases only one standard is needed, which is alumina."

Jan 1, 2003

By H. S. Sichel, W. J. Kleingeld, C. E. Dohm

A model of ore value distributions is presented that is the culmination of a statistical approach rather than simply a model that has been successfully applied to the evaluation of ore reserves. Detailed geological and physical observations based on large sampling data sets have been used to support the statistical modelling. Fundamental to the modelling process is the concept that the occurrence of a given grade value in space is a function not only of the presence of the mineral but also of the fact that it is associated with a specific trapping mechanism. The concepts have been specifically applied to gold mineralisation

Aug 1, 1995

By Craig M. Sams

"Variable speed mill popularity has grown during the last 10 years with almost every SAG mill fitted with a variable speed drive. In addition, many of today’s larger ball mills are running a variable speed drive for various reasons. In the past, motor suppliers, especially gearless drive suppliers, have considered mills as being an overpriced rotor. This has lead to mills demanding more torque than what a motor can generate. This paper identifies the reasoning of what has happened and how to mitigate the mismatch in the future. Technical and economical issues are discussed, allowing mill operators to make an informed decision of which path to take in deciding what motor to put on a mill.INTRODUCTIONIt has been generally accepted in the past that motor suppliers and specialists in engineering companies understand the workings of a SAG mill or a ball mill and although there is a fair knowledge within the industry, in regards to mill torque requirements, the advent of variable speed drives in ball mills has shown the writer that a complete understanding of the mill torque requirements are not fully understood.This paper will discuss two aspects of mill torque requirements, (operating torque at various charge levels and start up torque), and how it relates to specifying the proper motor torque requirements.MILL OPERATING TORQUEMill operating torque at a given charge level and density in a mill is essentially constant throughout the entire speed range. For the purpose of this paper, we will take a 38’x 22.5’, 20’ EGL, SAG mill and provide the power draw at variable speeds but fixed loading conditions.The power draw and mill torque of this mill at 8% ball charge and 28% total loading (Highlighted) is shown below as Figure 1, at variable speeds."

Jan 1, 2007

By L. E. Cardwell

This publication contains routine analyses and related source data for 475 natural gas samples from 17 States and two foreign countries. Of this total, 454 samples were collected during calendar year 1971. The remaining 21 samples were collected during previous years, but releases granting permission to publish the analyses were not received until 1971. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Thirteen previous publications have presented the results of 9,427 gas analyses prior to 1971. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1972

By B Stewart

It has long been recognised that knowledge of the conditions existing in a mine after an incident is essential in deciding whether to deploy responders as part of the incident recovery process. Applying this knowledge in a structured manner to the assessment and the acceptability of the risks likely to be faced by those teams during response activities before authorising their deployment is an onerous task incumbent upon the person controlling the incident response. The Mine Event Management System (MEMS) provides structure and coordination in the management of mine events. It assists with the skills and knowledge for incident control teams to effectively manage any emergency or non-emergency event, be it large or small. In cases where multiple organisations are involved, the MEMS promotes effective joint operations through the use of common terminology and structure to provide seamless communication between agencies at all operational levels. The SQL-based software developed by Queensland Mines Rescue Service (QMRS) assists decision-makers to make considered options; it does not make decisions for you. When set-up, it allows the information that already exists within a mine’s Safety Health Management System that is relevant to the incident to be accessed and considered rapidly within the pressured environment of an emergency. Additionally, the incident specific questions contained within MEMS focuses the management team on gathering and assessing information relevant to the incident as it progresses. The software’s event log can be utilised as an auditable document for post incident investigation. The MEMS provides a process to properly consider the adequacy of the information available upon which decisions have to be made, to consider and acknowledge the hazards of the environments within or adjacent to which responders will need to work and to acknowledge and authorise the entry of responders into or to remain within a mine either during or post an incident occurring, once an acceptable level of risk is achieved.

Apr 16, 2024

By K. Grubaugh

Ghana’s physiographic and geologic features are the basis for its long mining history. The Gold Coast colony has been a significant producer of gold. The gold of the Akan forest (Ghana) was a terminus for caravans that plied Saharan trade routes. Now it also produces significant quantities of manganese, bauxite, and diamonds In addition, the country produces kaolinite, silica for glass, salt, and both aggregate and dimensioned stone. Most secondary minerals are consumed locally but some amounts do find international markets. Ghana revised the mining laws and regulations in 1986. These revised laws dramatically increased gold production and improved the country’s economy. The success of these laws spawned imitators in other African states such as Cote d’Ivoire, Mali, and Burkina Faso. Representatives of these countries claim Ghana was their model. Environmental regulations exist but an intensive adversarial atmosphere is lacking. Ghana has also offered the mining industry incentives like accelerated depreciation rates and exemption from import duties on related supplies and capital equipment. The country has also pursued an aggressive policy to restore the nation’s business infrastructure.

Jan 1, 2001

By S. Uddin

An integrated device has been developed to measure sedimentation potential, conductivity and pH simultaneously of particulate systems. Maxwell?s model was used to calculate volume fraction of solid from the conductivity data. In this approach, all system variables are known and zeta potential can be calculated from Smoluchowski?s equation. The technique is validated by comparing zeta potential vs. pH for alumina and silica suspensions with electrophoresis measurements. The technique was extended to mixed alumina/silica systems. Sufficient column height along with size difference between the two minerals allowed gravity fractionation during settling. Sedimentation potential measured over time identified the transition from one mineral to the next. Using XRD analysis the results supported the correlation between surface charge and sample composition. This is a step towards characterizing surface charge of mixed systems of interest in mineral processing.

Jan 1, 2010

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By R. Benito

The publication of the Lerchs Grossmann paper in 1965 outlining a threedimensional graph algorithm for ultimate pit definition set the standard for the mining industry regarding pit optimization. Although the algorithm provides a solution from a static standpoint (i.e., assumes instantaneous mining), it is widely used for commercial packages to generate ultimate pit limits and intermediate phases. However, the solutions delivered are presented in canned reports lacking connection to the original data, which prevents further data analysis and extended reporting. The approach presented in this paper attempts to overcome such barriers by performing openpit optimization through databases. An adaptation of the Lerchs Grossmann graph algorithm is used to generate nodes, arcs and tree structures in customized tables to determine the maximum closure of a graph.

Nov 1, 2013

By L. Chen, G. A. Brooks, S. A. Nightingale

The dissolution of alumina and magnesia has been investigated using laser scanning confocal microscopy (alumina) and a rotating finger apparatus (magnesia) to assess the effects of temperature, composition and forced convection on the rate of dissolution in CaO-SiO2-Al2O3based slags. The two techniques have differing strengths and limitations, and provide complementary methods for studying dissolution. Alumina dissolution was studied for temperatures from 1477 to 1577°C. Based upon the data, the rate controlling mechanism was thought to be mass transfer control in the slag. The diffusion coefficients for the alumina particles are estimated to be in the range 10-11to 10-10m2.s. MgO degradation for sample rotation speeds of 50 to 800 rpm at 1500 and 1530°C was studied for both congruent and incongruent dissolution. The results show that the rate of dissolution for this is primarily controlled by a diffusion mass transfer mechanism for congruent dissolution except at the highest rotation speed. For incongruent dissolution, the mechanism is much more complex, with the morphology and distribution of the spinel reaction product having a significant effect. At high speeds and prolonged times, mechanical forces played a major role in the degradation process. Keywords; kinetics, corrosion, refractories, dissolution rate, inclusions, mass transfer, slags, steelmaking

Jan 1, 2004

By D J. Corp

The Halmahera Contract of Work is a sixth generation contract held 82.5 per cent by Newcrest Mining Limited and 17.5 per cent by PT Aneka Tambang and takes in the Gosowong Project area. In 1991 Newcrest Mining Limited established a small exploration office in Jakarta and proceeded to seek exploration opportunities. The Halmahera area was identified as a substantial prospective ground position in a relatively unexplored area. In late-1991 Newcrest Mining Limited and PT Aneka Tambang agreed to explore in Halmahera. Initial field work commenced in July 1992. A vigorous ground reconnaissance programme led to the discovery of the Gosowong deposit a little over 12 months later in September 1993. In April 1997 the Contract of Work was approved covering much of the island of Halmahera. Between September 1997 and November 1998 activities were directed principally towards obtaining the necessary permits required to commence construction activities. Some particularly ambitious targets were set for achieving this outcome. An aggressive construction programme commenced in late-1998. Construction took place during a period of unseasonally high rainfall, which in itself presented additional challenges to the construction team. A key milestone for the project was achieved on 1 July 1999 when wet commissioning of the process plant commenced. Construction of the Gosowong Mine was achieved on time and within budget. A period of some six years elapsed from the initial discovery of the Gosowong deposit to the time of the first gold pour. Much of the permitting, construction and commissioning activity took place between September 1997 and July 1999. This coincided with a period of significant social, economic and political upheaval in Indonesia. During the construction period a high level of importance was placed on the structured recruitment and training of local people, as well as fostering appropriate community and local business development programmes in the communities nearby the project. Emphasis was also placed on environmental management with detailed long-term planning and progressive rehabilitation commencing during the construction phase. The permitting and subsequent development of the Gosowong Project has demonstrated that even during the difficult times, with commitment, it is possible for mining and exploration companies to conduct business in Indonesia.

Jan 1, 1999

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By R. Zivojinovic, S. Vujic, T. Tanaskovic

The problem of determining the optimum exploitation life of machinery, namely the optimum time for machinery and equipment replacement, represents a complex and highly responsible engineering task. Taking into consideration the situation prevailing at coal pit mines in Yugoslavia, the tasks of this class are very complex and difficult. To make a decision on replacement of capital equipment and machinery, such as bucket wheel excavators within the mentioned systems, understands a management task of utmost responsibility. It requires high professional and analytical knowledge as well as the reliable arguments, based on multidisciplinary professional approach. In this paper, the authors present their views on the problem of establishing the optimum exploitation life of bucket wheel excavators, offering an algorithm, based on dynamic programming, as a solution. Keywords: Bucket wheel excavators, exploitation life of machinery, optimization, operations research, theory of replacement, dynamic programming

Jan 1, 2003

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By Z. T. Bieniawski, Benjamín Celada

After emphasizing the importance of quantitative rock mass classifications in mining, originally directed to selection of rock support measures, but subsequently to estimates of rock mass properties such as rock mass strength and rock mass modulus of deformation, current attention calls for a classification specifically for rock mass excavability by tunnel boring machines (TBMs), which are used extensively in tunneling as well as in the mining industry. This paper introduces the Rock Mass Excavability (RME) index for predicting excavability of rock masses by TBMs using a quantification of machine performance and rock mass conditions. The RME index is based on five input parameters aimed at relating rock mass behavior and machine characteristics: (1) uniaxial compressive strength of the rock material, (2) drillability/abrasivity, (3) rock mass jointing at mine drift face, (4) standup time of the excavation, and (5) groundwater inflow. Development of the RME index entailed the collection of extensive data from more than 28 km of tunnels and some 400 case records from projects in Spain involving double-shield TBMs. In the process, a number of statistical correlations have been established between RME and such output parameters as degree of machine utilization, advance and penetration rates, thrust and torque of the cutterhead, and the specific energy of excavation. It was found that the RME index provides a particularly significant correlation for predicting the average rate of advance (m/day). In essence, the RME index is a classification system that features interaction of rock mass conditions with boring machine characteristics for use in the early stages of a project. It should be noted that the RME index does not replace the Rock Mass Rating (RMR) or Q-systems as used in mining and tunneling; indeed, one of the RME input parameters, standup time, is determined from the RMR. However, the approach presented introduces a specialized tool relevant to excavating tunnels and drifts. Possible applications to hard-rock mining are explored.

Jan 5, 2007

By G. L. Oldright

The first Report of Investigations of the present series (No. 4562) was on the fundamental properties of lead compounds, and the manner in which they set limits to the richness of lead products treated in the usual sintering-blast furnace units. These properties of the compounds were emphasized, as&apos; it was desired, also, to learn the limitations of smelting the same compounds in present ore hearth practice; the hearth has a competitor in these "usual" units, even with the rich lead feeds best adapted for the hearths. Operating conditions that were followed in older metallurgical processes, when rich products, were treated, were outlined. The second report of the series (R. I. 4563) was on the development of the ore hearths of the types now used in the Tri-State from the viewpoint of the features, functions, and dimensions of the earlier hearths that had been most changed. Experimental data, for both well and poorly desulfurized charges being considered, were given to show the relative changes in the sizes and compositions of the charges after they were added to the ore (Scotch) hearths. A general picture was given of the charge column and of the conditions prevailing there when the operation was satisfactory. In this third paper, the composition of the gases prevailing in the charge column at various elevations will be correlated with what has been learned of the nature of the charge column in order to trace the steps of operation by which lead sulfide is converted into metallic lead. The metallurgical factors that govern operation and the lines along which improvements may be made will be noted.

Jan 1, 1949

By Robert K. Jonas

"Minerals processors can improve production by using the best available control technology to control their operations. Many mines use expert systems that can provide improved results over manual or basic control, but better results can be achieved using multivariable predictive control. Over the past few years, the application of multivariable predictive control has gained acceptance in many mining processes and has recently proven to be suitable for some of the most challenging processes. This advanced control technology has been successfully applied to a wide variety of processes; alumina digestion, ball mills, CCD/thickeners, kilns/calciners/roasters, heat exchangers/evaporators, and more demanding processes like SAG mills and flash smelters.This paper discusses the needs of advance control technologies in the mining industry, including the impact of these technologies on best practices for implementation and long term sustainability. Results of the multivariable predictive control applications in mineral processing are discussed, and in particular the application to the SAG mill. In addition, an example of the benefits improvement that can be achieved with this technology is presented.INTRODUCTIONThere has been a long term perception in the mainstream mineral processing industry that best advanced control solution is an expert system. There a numerous instances of expert systems used for control of SAG mills, as well as kilns or roasters, thickeners and more recently flotation circuits. Many of theses expert systems have been installed by small, independent companies or by OEMs of processing equipment. Undoubtedly these expert systems have provided millions in benefits to the owners of mineral processing plants.It is this author’s proposition that it is a misconception to believe that expert systems are the best solution for mineral processors, and that in many cases the best solution is Multivariable Predictive Control (MPC). Better control and optimal operations can be achieved through the use of MPC. Another important consideration when considering advanced control technologies is the implementation and support effort. These types of applications have been known to deteriorate, even to disuse, when they are not kept up to date with changes to the process or equipment. The audience is invited to listen to discussion and draw their own opinion. The author has been involved in installing control systems for over 20 years, advanced solutions for over 15 years, and has had privilege to consult with many miners concerning the selection and application of advanced controls over the past 6 years."

Jan 1, 2008

The Epithermal and Mesothermal Gold Prospectivity modelling projects carried out by Crown Minerals provided explorers in New Zealand with a new compilation of historical exploration data combined with new geological information from the GNS QMap 1:250,000 scale mapping project. These data were used to produce predictive mineral potential maps for gold mineralisation in New Zealand. The aim of these projects, to stimulate mineral exploration and investment in exploration, has been successful with eight new companies acquiring new tenement positions and committing significant exploration expenditure to exploring in New Zealand in the coming years. The projects were done at a national scale and consequently not all exploration data were compiled into the prospectivity models. Several of the new companies recognised the value of the prospectivity modelling work and committed exploration funds to continue the modelling process. They recognised a need to compile the remaining data and run the models again to allow detailed exploration targeting. Detailed data compilations including digitising historic exploration stream sediment sample, rock chip sample, soil sample and drilling data has been completed. New models have been completed in Otago for mesothermal gold mineralisation and in the Coromandel and Northland for epithermal gold. The new models have been compared with the original regional scale models and used to target prospect scale exploration. This work has allowed exploration models for epithermal and mesothermal mineralisation in New Zealand to be refined. More importantly this work has identified significant areas with potential to host gold mineralisation with little or no systematic geochemical data including soil sampling or drilling. Exploration work programs have been designed to acquire these missing data and exploration funds have now been committed to test the areas highlighted by the prospectivity modelling. In summary, the Epithermal and Mesothermal Gold Prospectivity modelling work has successfully attracted new investment and ideas to the exploration scene in New Zealand. The projects had an estimated cost of NA$250 000 and will in the next two years, just through exploration expenditure, attract more than NZ$10 M in investment. If a mine is discovered the return on investment will be considerably greater.

Jan 1, 2004

By Noel N. Moebs

The coal wants at the Westland Mine in southwestern Pennsylvania consist chiefly of elongated, sandstone-filled channels with slickensided basal contacts. Tentatively identified as washouts, these channels are about 1,000 feet long and 300 feet wide, are erratic in occurrence and trend, and are difficult to delineate from the customary core drilling pattern. Roof conditions are hazardous adjacent to the washout contact, but roof stability is generally unaffected greater than 30 feet away.

Jan 1, 1981