Search Documents

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By Phillip N. Yasnowsky

This Bureau of Mines publication tabulates State taxes levied on nonfuel minerals that have the characteristics of a severance tax.

Jan 1, 1978

By Elisa Alonso

Manufacturing firms that rely on finite resources have a stake in ensuring sustainable materials use. Higher material prices and uncertain material supply, consequences associated with scarcity, can be damaging to firms. Firms have a number of options to improve material sustainability including dematerialization, material substitution and recycling. However, these options require technological capability, capital investments and supply-chain infrastructure; firms may decide to make such investments only if material prices increase. Once decisions are made, the barriers and delays to implementing changes may harm firms. The impact of not reacting to changes in material supply on firms was examined for the case of different platinum-using industries. It was found that taking action is particularly important for firms when limited material availability leads to volatile market conditions. Industries can benefit especially if they ensure process flexibility and have options for changing their material use patterns.

Jan 1, 2010

By M. M. D. S. Vemba

Paper written on project work carried out in partial fulfilment of B.Sc. Eng (Mining Engineering) degree Engineering refers to the application of mathematics and other sciences to logically develop solutions to problems. However, in opencast mining, due to the randomness of operations, the use of mathematics is often neglected. Instead, practices that have proven successful elsewhere tend to apply. At the other end of the scale, mathematical models have been developed to identify and quantify all the operational parameters involved in the loading and haulage of ore. These are then used to optimize the operation. Optimization in this context, refers to the reduction of cost through effective utilization of the available time and resources. Considering these mathematical models, the loading and transport system at SMC (Catoca Mining Society) will be assessed with a view to its optimization. The discussion will be introduced by considering the mine background and other general information, which will highlight the main operational variables.

Jan 1, 2004

By C. Larsen, E. Gratch, B. Flintoff, R. Bradburn

"In 1973 Brenda Mines Limited first investigated the potential use of a process computer to aid in the development of a control system for the concentrator grinding circuit. This initial study and its results are reviewed (1) in a previous paper.Since that time the computer system and its applications have been expanded. After the initial success of grinding circuit control, a second process computer was purchased to function as a back-up device. The two processors are currently operated in a foreground-background mode which allows extensive use of the computing facility for engineering and development work as well as operator training.Because of the relative ease of expansion, the computer has been incorporated into a flotation control system as well as an electrical peak power savings program.It is the purpose of this paper to review the successful application:; of the process computer and to indicate applications which are envisaged for the future."

Jan 1, 1978

By Yuanyuan Wang, XUEWEN WANG, Jinzhi Wei, Ligang Wen, Muxin Jia, Zhengyao Li

The abstract discusses the use of disodium carboxymethyl trithiocarbonate (D8) as an effective depressant in the flotation separation of stibnite and pyrite. The study investigates the mechanism behind D8's selective inhibition of pyrite, utilizing techniques like micro-flotation experiments, contact angle measurements, infrared spectroscopy, adsorption capacity analysis, and zeta potential measurements. The findings reveal that D8 physically adsorbs onto both pyrite and stibnite, but its adsorption capacity on pyrite is significantly higher. This adsorption enhances the hydrophilicity of the pyrite surface, hindering the adsorption of the collector and effectively depressing pyrite flotation, while having minimal impact on stibnite floatability.

Mar 14, 2022

By E. D. Attanasi

Geologic resource assessments describe the location, general characteristics, and estimated volumes of resources, whether in-situ or technically recoverable. Such compilations are only an initial step in economic resource evaluation. Forecasts that assume that resources that exist in nature can be commercially produced as needed ignore economic constraints. This paper identifies, by example, the salient features of a geologic assessment that will assure its usefulness for economic analysis. These features are demonstrated with examples of coal resource assessments and coal bed gas assessments.

Jan 1, 2001

By F. L. Casey

"Part 1 – Published Papers Baria, G., and Boshkov, S., ""Insights into Undercuttingin Block Caving"", Proc. 5th Rock Mech. Symp.,Mines Br. - Information Canada, 41-58, 1970.Barron, K., Coates, D. F., and Gyenge, M., ""ArtificialSupport of Rock Slopes'', Mines Branch ResearchReport R228, July, 1970.Barron, K., ""Criteria for Brittle Fracture Initiation inand Ultimate Failure of Rocks and Their Applicationto Fracture Zone Prediction"", Proc. 2ndCongr. Int. Soc. Rock Mech., Belgrade, 1970, 3-37.Bauer, A., and Calder, P. N., ""Projectile Penetration inRock"", Proc. 5th Rocle Mech. Symp., Mines Br. -Information Canada, 157-170, 1970.Bauer, A. M., ""Site Development and Rehabilitation ofPits and Quarries"", Canadian Mining Journal,Vol. 91, No. 7, 77, July, 1970."

Jan 1, 1971

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By S H. Son, M K. Wang, H K. Jeong, B K. Cho, J I. Park

The utilisation of low-grade raw materials such as fine iron ore and semi-soft coking coal, and reduction of CO2 emissions are important issues in the ironmaking process. To solve these issues, a new process called PosPRA (POSCO prereduced agglomeration process) has been developing at POSCO. It focuses on the reduction of carbon composite iron ore briquette in travelling grate. In this study, the possibility of manufacturing the prereduced agglomerate (PRA) under oxidising atmosphere with travelling grate and the optimum manufacturing conditions of carbon composite iron ore briquette are investigated. The results have shown that controlling the temperature and oxygen potential in the range from 1100 to 1200°C and below 10 vol per cent respectively is very important to increase the reduction efficiency of briquette in travelling grate. High quality properties of the green briquette and PRA could be manufactured by using the briquette mixed with 20 wt per cent of coal under 0.1 mm in size under compacting pressure in the range from 3 to 7 t/cm. Adding 1 wt per cent water as a binder is proper under the condition of high compacting pressure. In a pot grate test, the compressive strength and metallisation degree of PRA are achieved over 150 kgf/p and about 55 per cent respectively, at bed temperature 1150°C and oxygen potential of 10 vol per cent when 20 wt per cent of coal is mixed in the briquette.CITATION:Wang, M K, Son, S H, Park, J I, Jeong, H K and Cho, B K, 2017. Development of prereduced agglomeration process using carbon composite iron ore briquette in travelling grate, in Proceedings Iron Ore 2017, pp 111–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining community about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

May 1, 2008

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

By A. N. Fried

With the growing importance of fluid injection in recent years, the petroleum industry has been investigating and field- testing a variety of new methods designed to modify the physical properties of reservoir oil to improve the efficiency of gas and water injection. These procedures include condensing-gas drive, LPG (liquefied petroleum gas) injection, alcohol-slug process, high-pressure-gas displacement, detergent-solution flooding, and in situ combustion (30, 37).3 A new and different method to increase the effectiveness of gas and water injection has been tested by the Bureau of Mines, Consideration of both fundamental and practical factors that operate to limit the oil recovery attain- able by conventional oil-displacement mechanisms led to the concept of a displacement mechanism called the foam-drive method. This report describes the experimental study that tested this concept in the laboratory.

Jan 1, 1961

By J. M. Ortiz

Mineral resource evaluation requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Usual practice is to consider the domain boundaries as hard, i.e. data from across the boundaries are disregarded when estimating the grades within a given domain. This practice may hinder the quality of the estimates when a significant spatial correlation of the grades exists across the domain boundaries. In this paper, several geostatistical methodologies to handle soft geological boundaries are compared through a case study on a copper mine in Chile. The estimation methods considered are: ordinary kriging using hard boundaries between geological domains; ordinary kriging omitting the geological boundaries; traditional and standardized ordinary cokriging of the grades assayed in different domains; ordinary kriging within dilated geological domains, that is, incorporating samples from adjacent domains up to a given radius from the boundary of the domain being considered. The estimations are performed using a set of exploration data (drill hole samples) and are validated using a set of production data (blast hole samples collected for grade control). Results indicate that kriging with dilated domains performs better than ordinary kriging using hard boundaries or no boundaries and better than the ordinary cokriging approaches. It therefore appears as a simple alternative to global kriging (without considering the geological domains) and allows accounting for changes in the grade average, dispersion and spatial continuity with the geological characteristics of the deposit, via the use of grade variograms proper to each geological domain. The maximal distance for searching samples from adjacent domains should be chosen according to the spatial correlation of the grades across the domain boundaries, or via a cross-validation at an early stage of the mine or a jack-knife if production data are available. Keywords: Kriging; cokriging; soft boundaries; hard boundaries; geological control; geological domains.

Jan 1, 2006

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By P. R. Clark, M. D. Gleghorn

"IntroductionAt TransAlta Utilities Corporation's Highvale Mine, located west of Edmonton, Alberta (Fig. I and 2), dragline stripping has proved to be a practical and economical method of overburden removal and future plans have been based upon the continued use of draglines (Fig. 3) as the major stripping equipment (Williams, 1979, Nikols et al., 1986). However, long range planning has shown that the capacity of draglines alone will be exceeded in the early 1990s as mining progresses into deeper overburden cover (Tapics, 1983). Strip ratios will increase from I.3 bank m!/ t of coal in 1985to 4.5 bank m3 / t in 1995. During this period the depth of overburden will increase substantially and the areas to be mined will be characterized by weak soils including glacially displaced overburden. This increased overburden depth in relatively weak soils will make it impractical to _continue side casting by draglines without prestripping in advance. In 1983, a major investigation was initiated to determine what additional overburden removal equipment was appropriate to the Highvale operations, and recognizing the long delivery times of this major equipment. when it would be required. This paper describes studies and tests which were undertaken in 1983 and 1984 to select prestripping methods and equipment for the future operation of the mine.Previous planning studies have shown that with the current burn schedule and with the economies of progressing from low cover to high cover, as has been practiced in the past, overburden volumes will exceed the capacity of the existing draglines in the early 1990s (Fig. 4). These previous studies had placed reliance on (I tandem dragline operation for future overburden removal requirements up to a depth of 45 m throughout the Highvale Mine. New drilling together with the associated geotechnical studies and some detailed planning on the practicality of using tandem draglines, created concerns about their universal application. Even without considering geotechnical conditions there was a depth limitation to tandem dragJines and substantial prestripping would be required to achieve the ultimate depths."

Jan 1, 1987

By Mandy Korff

Walls consisting of CFA-piles are often used for vertical cut offs for building pits. Several methods of installation and geometry may be used and sizes, depths and strengths of walls necessary vary widely. Based on experience with secant CFA-pile walls in The Netherlands, requirements for this type of wall can be set with a risk management view to it. This paper describes those requirements, based on specific local conditions.

Jan 1, 2006

By Vasile Pop, Ovidiu Galca, Constantin Salajan

The paper comprises a brief presentation of the rock fracturing techniques applied in CNMPN “REMIN” Company’s mines in Baia Mare. Parallel are emphasized some shortcomings of this field. The second part of the paper includes our preoccupations and achievements, of the last period, in especially those linked to techno-economical indices improvement resulting from the development of relatively large section mining works and blasting applied with sublevel caving methods.

Jan 1, 2003

By A Rorke, B Cubitt, R Beeslaar

The recent drop in the value of the South African Rand has resulted in an increased export value for South African coal and has lead to new coal reserves becoming available for mining. Very often these reserves are in close proximity to existing structures and utilities thus calling for stringent blast control measures to keep the risk of vibration, air blast and fly rock damage to a minimum.

Jan 1, 1997