Search Documents

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By R. J. Hundhausen

This report describes the exploration and recent utilization studies the Bureau of Mines conducted on the Iron King, Chambers, and Dry Camp chromite deposits in the John Day district, Grant County, Oreg. The field investigations were undertaken during parts of 1939 and 1942 to determine the tonnage and grade of chromite in the district that could be utilized as a war reserve for the steel industry. As a result of the Bureau's field work, which included construction of 9 miles of access road, 6,204 feet of diamond drilling, 195 channel samples, and 1,020 linear feet of trenching, an ore reserve of 208,000 tons of 22-percent chromic oxide was indicated in the 3 deposits. Less than 1,000 tons of this ore has been mined since the field work was completed because the 2 largest deposits are submarginal in grade and there is as yet no incentive to develop and mine the ore. Since the war, however, the Bureau has been seeking means of utilizing the ore. Two methods of utilization that show promise are direct smelting of the ore in an electric furnace and use of the chromite for making refractory brick.

Jan 1, 1956

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal--conductivity method because of the relatively small amounts of this inert gas present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method3/ and a continuous analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of Mines. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company4/. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation;- Production is checked against the helium removed from the gas, which before the installation of the thermal--conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By Allan E. Koski

Ceveland-Cliffs uses a specialized software package in mine planning at the Empire Mine, an iron ore mine it manages on Michigan’s Marquette Iron Range. The application puts together years of mining experience that began in the early 1960s on the eastern end of the Marquette Range. The Empire Mine is in its 38th year of production. It uses the software to model a complex and highly variable low-grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short- and long-range planning.

Jan 1, 2000

By K. Wangerud, B. S. Caruso

A water balance model with deterministic and stochastic components was developed and used for the Gilt Edge Mine Superfund Site, South Dakota, to evaluate risks of contaminated runoff discharging to surface waters based on assumed water treatment plant (WTP) rates for different remedial alternatives. The objectives of the modeling were to use a stochastic approach for analysis of precipitation based on historic records, and for probabilistic estimation of annual and monthly runoff from primary disturbed/mining activity areas that currently requires, or will need, treatment at the WTP, water storage and changes in a major pit, and risk of contaminated water bypass of the WTP to a downstream drainage. Subareas/source areas generating contaminated runoff requiring treatment were delineated. A simple water balance model was used based on precipitation inputs and evapotranspiration and groundwater losses. Annual and monthly precipitation records for Lead, South Dakota were used to estimate precipitation at the mine site. A lognormal distribution was estimated for monthly precipitation. The stochastic software package/Excel add-in “@Risk” was used to generate random monthly precipitation values using a Monte Carlo method based on the distributions. The average annual and monthly distribution of pan and lake evaporation, and groundwater losses were also estimated for the site. Stochastic outputs from the model for the end of each month and year included contaminated runoff requiring treatment, water storage in mine pits and the risk of WTP bypass given different assumed WTP rates. The probability of the time required to dewater the pits was also modeled.

Jan 1, 2002

By James Dunn

“The strongest argument of the detractor (of mining)is that the fields are devastated by mining operations ...They argue that the woods and groves are cut down, for there is need of an endless amount of wood for timbers, machines and the smelting of metals. And when the woods and groves are felled, then are exterminated the beasts and birds, very many of which furnish a pleasant and agreeable food for man. Further, when the ores are washed, the water which has been used poisons the brooks and streams, and either destroys the fish or drives them away.” Georgius Agricola, 1556, De Re Metallica, translated by Hoover, 1950. Technical problems associated with the cleanup of historic mines are not new. Nor are they unique to the mining industry or the governmental agencies addressing them. Both face the same issues and challenges of defining the problems, evaluating remediation options and finding the most economic and effective solutions.

Jan 1, 1999

By I. W. Farmer

Weightings and water inflows into longwall workings often occur together, giving rise to discussions on their relative genesis. Case histories are introduced which indicate that most water inflows are associated with heavy weightings. Resultant large releases of energy can lead to extensive vertical fractures, which can drain water from aquifers or other sources, such as separation accumulations, onto the face. Effectively control of water inflows in these cases depends on face support and weighting control.

Jan 1, 1996

By J. W. Thompson

MEANING OF TERM, The term "minerals" when used in grants or in reservations or instruments of conveyance is not limited to metals or metalliferous deposits, whether contained in veins that have well-defined walls or in beds or deposits that are irregular and are found at or near the surface or otherwise. Byron v. Utah Copper Co., Utah, 178 Pacific 53, p. 58. The term "mineral" in its commercial sense has been defined as any organic substance found in nature having sufficient value sepa- rate from its situs as part of the earth to be mined, quarried, or dug for its own sake or its own specific use. Rockhouse Fork Land Co. v. Raleigh Brick & Tile Co., - W. Va., 97 South- eastern 684, p. 685. CONSTRUCTION AND MEANING. It can not be said that the term "minerals" includes only such substances as are procured by tunnelling and shafting, as much gold is procured by placer mining and rich deposits of manganese and other like ores are found upon the surface of the earth and are some- times obtained without either quarrying or mining. Rockhouse Fork Land Co. v. Raleigh Brick & Tile Co., W. Va. ——, 97 South- eastern 684, p. 685. GRANITE AS MINERAL. It has been determined that granite was included in a grant of minerals. Rockhouse Fork Land Co. v. Raleigh Brick & Tile Co., -W. Va., 97 South eastern 684, p. 685. See Armstrong v. Lake Champlain Granite Co., 147 N. Y. 495, 42 Northeastern 186.

Jan 1, 1919

By Paul M. Hall

In the last several years, the coal mining industry has made significant changes in the design of longwall mining systems to make them more productive. Some changes, such as increasing the length of the coal faces and increasing the capacity of the face conveyors, have resulted in problems with achieving sufficient motor torque to start and operate the longwall face conveyors. Other changes, such as increasing the size and/or decreasing the percent impedance of longwall power center transformers, have resulted in problems with the short-circuit currents on the transformer secondaries exceeding the interrupting ratings of the molded case circuit breakers used to protect the secondary circuits. A survey of 24 longwall mining systems in northern West Virginia was conducted to investigate both problems. The results of the survey are presented and analyzed. Several recommended solutions to the problems are presented to enable the coal mining industry to design safe and productive longwall mining systems.

Jan 1, 1982

By P Stephenson, G Mosher, M Berry, C Arnold, P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Globally, private minerals companies considering the transition to a public company and entrepreneurs looking to create a new public company through, for example, an initial public offering or by a reverse takeover have many options. For companies with assets around the Pacific Rim, there are arguably five key stock/securities exchanges that actively promote international minerals company listings, and these are located in Australia, Canada, Hong Kong, Singapore and the United Kingdom.Listing on any of these exchanges requires a range of technical, commercial, financial and legal documentation. Each exchange has specific rules and requirements for technical documentation to support the listing process. Once listed, each exchange also has specific rules for technical information to meet ongoing compliance requirements. The nature and detail of this documentation differs for the five exchanges.This paper presents statistics on the minerals company listings on each exchange and provides an overview of the technical documentation required to prepare for an initial listing and ongoing compliance.CITATION:Berry, M, Stoker, P, Stephenson, P, Arnold, C and Mosher, G, 2015. Technical considerations of public listing and ongoing compliance for minerals companies , in Proceedings PACRIM 2015 Congress, pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By Orlando E. Romig

As metals and alloys are composed of an aggregate of allotriomorphic crystals or grains, each possessing an individual orientation, the physical characteristics of a metal or an alloy are closely related to the properties of the individual crystals. The preparation and study of single metallic crystals are, therefore, matters of considerable importance. The advent of the X-ray spectrograph as a valuable metallurgical tool has magnified the importance of this subject, because the interpretation of some X-ray spectrographs is difficult unless single crystals are used in these studies. Previous Work The first paper, as far as the writer knows, on the behavior or preparation of single crystals of metals is by Baker.' He describes the behavior of extruded wires of sodium and potassium. These wires, when pulled in tension, instead of showing the usual conical fracture common to most metals, had a chisel-shaped fracture when they were broken. I and 11, Fig. 1, have a similar fracture. Baker checked his results by preparing single crystal wires from molten sodium and potassium and observing their properties. He pre- pared the wires by filling glass tubes, under oil, with the molten metal. The surfaces of the strained wires showed slip bands of remarkable clearness of which photographs are shown in his paper. He concluded that these wires were single crystals and "that the portions of the metal brought into play are cubes. Such cubes, when placed so that a plane through two opposite edges was parallel to the axis of the wire, would allow of lateral contraction by faces gliding over one another in one direction only and not in the direction at right angles."

Jan 1, 1927

By Peter A. Rona

The Mid-Atlantic Ridge in the central North Atlantic and the Gorda Ridge within the U.S. Exclusive Economic Zone off northern California and southern Oregon are yielding new discoveries of seafloor hydrothermal mineralization. The TAG hydrothermal field in the rift valley of the Mid-Atlantic Ridge near 26 degree N, 45 degree W has been a site of international collaborative research since the discovery there of extensive manganese deposits associated with low temperature hydrothermal activity in 1973 as part of the TAG (Trans-Atlantic Geotraverse Project). The first high-temperature hydrothermal activity, massive sulfide deposits and vent biota discovered in the Atlantic were found at the TAG hydrothermal field in 1985. Collaborative dive series with DSV ALVIN in 1990 and in 1991 with the two Russian MIR submersibles in the TAG field have found and sampled large inactive sulfide mounds in addition to the previously known active sulfide mound. The active sulfide mound on the floor of the rift valley is about 250 m in diameter and 40 m high with a concentric zonation of mineral types and flow regimes decreasing in temperature from 365 degree C black smokers at the center to white smokers and diffuse flow toward the margins. The recent dive series in coordination deep-towed instrument surveys have delineated a zone extending about 5 km along the lower east wall of the rift valley of inactive sulfide mounds up to a kilometer in diameter. MIR Mound in this zone consists of a central sulfide zone about 400 m in diameter and 50 m high surrounded by a halo of low-temperature deposits to 200 m wide. Inactive sulfide chimneys contain the first primary, free gold grains found at a hydrothermal site on a mid-ocean ridge (P.A. Rona, Y.A. Bogdanov, E.G. Gurvich, N.A. Rimski-Korsakov, A.M. Sagalevitch and M. D. Hannington, 199 1 EOS, Transactions, American Geophysical Union, 72:470-471 and Journal of Geophysical Research, submitted).

Jan 1, 1992

By Michael J. Lord, Richard H. O. Wagner

"The technologies used in the mineral processing of ores are being increasingly applied to the identification and remediation of metal contaminated industrial, military and landfill sites. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed, or sent to a landfill. A systematic characterisation of the site material is first undertaken. Bench and pilot testing follows to evaluate criteria for metal separation. The testing may examine one or more physical or physico-chemical reprocessing methods, singly or in combination, for the remediation of the test samples. These mineral processing tests determine the % metal removal fiom the soil and the contaminants concentrated from the medium. The usefulness of mineral processing testing for site remediation flowsheet design and execution is illustrated by the case studies presented. This paper will present the test results of three case studies: an industrial site decontamination, the cleanup of a small arms firing range, and the reclamation of property within a landfill.INTRODUCTIONEnvironmental legislation and our society’s quest for a cleaner environment has led to the application of mineral processing expertise and technology for industrial site decontamination, military site cleanup and landfill reclamation. Although the required level of decontamination varies between jurisdictions, a site becomes a candidate for decontamination once the contaminant concentrations are found to exceed the Canadian Council of Ministers of the Environment (CCME) Interim Remediation Criteria for soil (decommissioning guidelines) or applicable provincial guidelines. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed or disposed of in a landfill"

Jan 1, 1999

By Raymond J. Pichette

"Aeromagnetic data can be useful in helping to delineate structures and rock types in gold exploration. Magnetic anomalies associated with Archean volcanic belts in northeastern Ontario can be quickly and effectively analyzed in profile form with the use of model curves. The model curves help to locate contacts between strata. They also help to estimate the magnetite content of the rocks and their depth beneath overburden.An aeromagnetic map of part of Catharine Township, Ontario has been analyzed with the aid of model curves. Several magnetic rock types, potential fault zones and areas of relatively thick overburden were delineated.IntroductionIn any exploration program, a good understanding of the stratigraphy, rock types and structure enhances the possibility of success. For example, environments which host gold deposits in the Abitibi Volcanic Belt may be characterized as follows (Jensen, 1980; Pyke, 1980):(I) They have major faults, especially as tectonic boundaries between volcanic piles which include mafic and ultramafic rocks and clastic sedimentary rocks or gneisses.(2) They have subvolcanic felsic intrusions.(3) They have extensive carbonitization, with or without carbonate and sulphide-facies iron formation.In all cases, delineation of structure and rock type should be a major objective in exploration. The analysis of magnetic data can be a useful tool in this task. This paper is presented with the purpose of describing the application of the magnetic method to gold exploration in Archean volcanic terrains.Magnetic AnalysisTotal-intensity magnetic contour maps can be used to discriminate rock units according to differences in magnetization. However, because of smoothing of texture resulting from the compilation procedure and the fact that survey lines are widely spaced, contours should not be directly used for quantitative analysis. A much more definitive means of magnetic analysis is provided by the use of the original profile or chart recordings. Model curves provide a basis for analyzing these profiles both accurately and rapidly."

Jan 1, 1982

By D. R. Torgoson, Th. G. Sahama

"This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2siO4 and MgSiO3-FeSiO3 and gives the results of a thermodynamic attack on the problems of stability end parageneses.. Although some data are lacking satisfactory agreement with mineralogical and petrological observations is indicated.The use of thermodynamic methods in mineralogy and petrology has been rather limited, because accurate thermal data, especially for the more complicated and more important rock-forming minerals, have been too scanty to permit any systematic application to problems in those fields. It is, nevertheless, a fascinating task to investigate to what extent the mode of occurrence and the stability relations of the minerals and mineral parageneses, as revealed by petrological and mineralogical observations, agree with predictions of thermodynamics. At the present stage of development calorimetric data are needed for most of the abundant silicate minerals.Measurement of the heats of solution in hydrofluoric acid of minerals in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 affords a ready means of obtaining their heats of formation from the oxides. Combination of such data with entropy and heat-capacity values gives a means of obtaining free energies of formation from the oxides, which, in turn, are connected di¬rectly with stability and paragenoses.The two silicates of magnesium, Mg2SiO4 and MgSi03, occur as rock-forming constituents as forsterite and clinoenstatite or enstatite. The orthosilicate (forsterite) forms a series of isomorphic mixtures with ferrous-orthosilicate (fayalite). The continuity of this series, suggested by petrological observations, has boon proved experimentally by Bowon and Shairer.4/ The present work shows that those minerals constitute a series of perfect solid solutions - that is, a series of solid solutions for which heats of formation from the individual pure silicates, Mg2Si04 and Fe2SiO4, aro negligibly small.The metasilicates of magnesium and iron also form an isomorphic series. However, this series differs from the forstorito-fayalite series in the fact that the most iron-rich mixtures, between about En10Fs90 and pure Fs, appear to be unstable with respect to the paragenesis iron-rich olivine plus quartz. The supposed instability of pure FeSiO3 as a crystalline compound, at least at high and at moderate temperatures, is remarkable, as no crystal struc¬tural reason for such instability is apparent. The present work indicates, also, that these minerals form a perfect series of solid solutions and throws additional light on the instability question.In the following, the samples used in this investigation will be described. For each of the natural olivines and orthopyroxenes, with the exception of sample L, a chemical analysis was made of the purified and actually used fraction. All the analytical work was carried cut by Oleg v. Knorring, and the specific gravity determinations, by moans of a pycnomctcr, by Oiva Joensuu, both of the University of Helsinki, Finland. The determinations of the optical properties were made by Mrs. Toini Mikkola, of the Geological Survey of Finland."

Feb 1, 1949

By John C. Machisak

The Nation's mining and quarrying industries have again met the annual challenge to their ingenuity--that of reducing disabling work injuries among their employees. The effectiveness of management in facing this problem and in meeting this responsibility from the results of the 1961 National Safety Competition. Three hundred ninety-three or 45.3 percent of the mines and quarries participating in the competition established a new record number of participants operating throughout the competition year without a disabling work injury. Another record established in the 1961 contest was the number of participants (868) enrolled in the competition. This annual safety competition was begun in 1925 and is conducted by the Bureau of Mines, U.S. Department of the Interior. It provides for six bronze Sentinels of safety trophies which are awarded each year to the winning participant in each group. Since its inception, the competition has exerted a strong influence in the field of safety promotion. The statistical record of its accomplishments over the years gives strong support to the theory that well-organized and well-administered safety programs are effective tools to be used to reduce the number of disabling work injuries. It stimulates and holds the interest of employees and management in accident prevention. Because of this, mines and quarries participating in the contest have a more favorable safety record than those operations not enrolled.

Jan 1, 1963

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.

On Dec. 20, 2013, an 8-m (26.2-ft) diameter Robbins hybrid single shield/earth pressure balance tunnel boring machine (EPB TBM) was launched to bore the Grosvenor decline tunnel for Australia?s Anglo American coal mine. The machine was built using onsite first time assembly (OFTA) in order to fit within a tight project schedule. Assembly at the remote jobsite near Moranbah, Australia took about four-and-a-half months, and then the machine was walked down into a launch tunnel. Two decline tunnels, at grades of 1:6 and 1:8, will be used for mine access to new coal seams. The hybrid machine is tackling mixed ground conditions ranging from sand and clay to varying types of sedimentary hard rock up to 120 MPa UCS, as well as coal seams. Methane gas is expected to be present throughout the tunnel, so the machine has been designed as explosion-proof-compliant to ERZ-1. ?Grosvenor is the first underground coal mine in Queensland to use a TBM for drift construction,? said Glenn Tonkin, Grosvenor project director. ?We are proud to be pioneering this technology.? Only about 300 m (984 ft) of ground in each decline tunnel is expected to require EPB mode, while the rest of the tunnel will be bored in hard rock mode. Thus, the design was optimized toward hard rock excavation.