Search Documents

By R. F. Zaffarano

Intergrated energy balances and energy flows were constructed and quantified for State, regional, and national levels from four separate supply and demand commodity balances for coal, dry natural gas, petroleum and natural gas liquids, and utility electricity. These commodity balances were integrated by source and sectors through conversion and aggregation of their components to energy equivalents expressed in British thermal units (Btu). A summarization of the total gross energy components of supply and demand for commercial energy derived from direct fuels, hydropower and nuclear power, based on individual States and regions, is tabulated for 1960 and 1965. Pertinent computerization details and more than 500 individual State and regional printout tables, in both original commodity units and Btu's, are shown. Using these data, energy flows between States and regions were calculated to identify surplus and deficit energy areas. Report emphasis is on the conceptual aspects of integrated energy balances, rather than on the development of missing State energy data.

Jan 1, 1969

During heap leaching of secondary copper sulphide ores operated at low heap temperatures and high levels of leach solution salinity, copper recovery is usually unsatisfactory, due to a slow chemical and bacteriological leaching of the covellite minerals either formed from leaching of chalcocite or naturally occurring in ores. A laboratory test program was conducted to investigate the effect of leach solution temperature in the range of 20 to 50°C on copper extraction during stirred reactor, bottle roll, and short column leaching of fresh or heap leached secondary copper sulphide ores. It was demonstrated that increasing heap temperature is an effective approach for improving recovery of copper from secondary copper sulphide ores. A review of the technologies available for heating heap leach solution or decreasing solution salinity to improve copper recovery from secondary sulphide ore indicates that an integration of copper concentrate pressure leaching with heap leaching is potentially a cost-effective approach. A copper flotation concentrate sample was tested through pressure oxidation with the use of heap leach solutions of varying strengths for the repulping of the concentrate in order to examine its effect on pressure oxidation performance. The test results indicate that use of heap leach solution of high salinity in the pressure oxidation process does not cause a negative impact on the process performance for copper extraction, sulphide oxidation, and recovery of gold (if present) from pressure leach residue, and has additional advantages of removing the bacterially inhibitory aluminum from heap leach solution and generating more acid and ferric iron in the pregnant leach solution. A flowsheet configuration for full integration of the copper concentrate pressure oxidation with heap leaching of secondary copper sulphide ore is proposed and discussed.

Jan 1, 2014

By Norman O. Lotter, Virginia Lawson, Mika Muinonen, Dominic Fragomeni, Jorge F. Oliveira

Development of metallurgical flowsheets from drill core to production of finished metal involves two main domains: process mineralogy to sample the ore and develop a successful flowsheet producing saleable concentrate; and extractive metallurgy to convert that saleable concentrate to finished metal. Effective flowsheet development for a new or brown-field concentrator and processing facility is essential to project schedule and return on investment. Over the last decade in particular, the integration of geology, mineralogy, sampling, and mineral processing have empowered the development of an improved practice in flowsheet development. The use of geometallurgical units as a basis for best-practice sampling delivers representative study material to the laboratory. Modern automated mineralogy characterises the whole rock assembly and paymetal mineral hosting, to address downstream process implications. Batch scale flotation testing then uses this information to design and perform well-focused strategies. At early stages of the project, the Extractive Metallurgy team is engaged to determine processing constraints or other economic drivers in conversion of the saleable concentrate into finished metal. The team evaluates available technologies, assesses the impurities and key properties of the given concentrate. In many cases, changes to mineral processing flowsheet are required to maximize value per tonne of concentrate. Site conditions, availability of infrastructure, energy and power all play an important role. Modern metallurgical simulation tools such as FactSage™ and METSIM™ can quickly define the appropriate test program for each process. Bench scale testing and appropriate scale of piloting can confirm simulations and provide design criteria. A case study demonstrates how effective use of these tools and a multidisciplinary team can accelerate flowsheet development, while reducing costs and ensuring that the designed processing facilities maximize project value with minimum risk.

Jan 1, 2014

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By Shawn McWilliams, Aini Sun, Mike Lichte, Greg Colzani

The Allegheny County Sanitary Authority (ALCOSAN) adopted its Clean Water Plan (CWP) in May 2020, as part of a federal consent decree to comply with the USEPA’s Combined Sewer Overflow (CSO) Control Policy. Planned improvements include constructing a new regional storage/conveyance tunnel system, promoting green infrastructure/ source control, and expanding the treatment plant. Preliminary planning for the tunnel system was completed in October 2020. The Ohio River Tunnel (ORT) project is the first of three tunnel projects that make up the regional tunnel system. The ORT project began final design in 2021. This paper discusses the advancements made to the ORT preliminary planning concepts considering property availability, alignment optimization, tunnel boring machine evaluation, contract packaging and delivery schedules.

Jun 13, 2023

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

The Functional Performance Equation for ball milling circuits provides plant staff with a new means to improve circuit performance. However, successful execution of a plant project, with verifiable circuit processing performance improvements, requires a significant number of accompanying steps beyond the equation alone. In order to identify and articulate all these steps, a study with plant staff from two milling operations and a grinding media supplier was undertaken. ?Task analysis? of improving plant grinding performance was carried out. This analysis called for the development of a number of system components, and ultimately yielded a ?Plant Grinding Circuit Processing Performance Management/Improvement System.?

Feb 23, 2014

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

By Fraser M. Walsh

The objective of this program was to determine by laboratory experiments the kinetics and mechanics of the reactions that produce acid in coal mine drainage. The program was divided into three phases: In Phase I, five coil mines, representative of Appalachian coal mines, were chosen for sampling and an experimental design was identified suited to accomplish the program objectives. In Phase II, the five mines were sampled and test protocols applied. The results showed most pyrite weathering to be based on oxidation in the presence of water. Iron bacteria, especially Thiobacillus ferrooxidans, catalyzed the rate of pyrite weathering by a factor of three. An increase in initial iron concentration in a system that modeled the nine environment acted to inhibit bacterial catalysis of weathering. In Phase III, five tailings piles were sampled and the material obtained was used to evaluate this method of bacterial catalysis inhibition. The evaluation verified method effectiveness; inhibition of over 80% of the release of weathering products was observed.

Jan 1, 1982

By J. R. Thoenen, J. L. Vallely, M. C. Malamphy

"SUMMARYMagnetic and gravimetric surveys wore conducted over an area of ap¬proximately 1,400 square miles in the bauxite district of central Arkansas. The primary purpose of these surveys was to discover any possible buried and hitherto unknown syenite masses favorable for the occurrence of bauxite and to determine the approximate position of the buried flanks of the known syenite masses which might offer conditions favorable for the discovery of new ore bodies.Those surveys indicated that the various syenite outcrops were domes or bosses on a large batholith and that ether similar domes occurred on the batholith but did net outcrop.Drilling on the local geophysical anomalies proved the presence of 10 buried domes, but only 2 of them were found to project above the upper surface of the Midway clays, a requisite of conditions favorable for the occurrence of bauxite ore bodies. The geophysical data indicated the approximate configuration of the buried flanks of the known syenite coutcrops, and the portions of these flanks that project above the Midway have now been outlined more accurately by drilling.The geophysical surveys have produced evidence permitting the elimi¬nation of a large area as unfavorable for the occurrence of bauxite.Magnetic surveys extending along the Midway-Wilcox contact from Gurdon, in Clark County, on the southwest to Searcy, in White County, on the northwest have proved the improbability of the existence of other syenite masses similar to those found in Pulaski and Saline Counties. A detailed magnetic survey of the Magnet Cove area in Hot Spring County has proved that the syenite mass exposed in that locality is an isolated intrusion and entirely unrelated to those of Pulaski and Saline Counties. This syenite mass does not occur under conditions believed to be favorable for the occurrence of bauxite."

Feb 1, 1945

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry's larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989

By John P. Davis

The use of conventional, circulatory air rotary and fluid rotary, cased and uncased drilling methods in the vicinity of sensitive infrastructure can have deleterious effects on the ground conditions surrounding and supporting structures and the structure itself. Furthermore, the use of these conventional methods offers the engineer or contractor little information about the condition of the subsurface during geotechnical applications. Conversely, sonic drilling measurements and samples can be used to evaluate actual conditions during the progress of exploration and construction across a given site. This paper will discuss the history and properties of sonic drilling and explore case histories of geotechnical applications for the advancement of boreholes within vulnerable structures and on sensitive sites for several recent infrastructure projects ? a tunnel and railroad project, a dam grout curtain project, a bridge micropile exploration project and a tunnel instrumentation project. Project summaries will discuss the advantages realized when the application of sonic drilling techniques demonstrated superior accuracy, quality control, efficiency, productivity, penetrability, waste minimization and adaptability when drilling adjacent to or within existing infrastructure. Finally, the discussion will address the current testing and application of sonic drilling to the installation of micropiles, earth retention anchors, grout injection and instrumentation installation where the quality control benefits provided by the inherent soil cores, measurement while drilling systems, accuracy and non-destructive production drilling features will be advantageous.

Jan 1, 2006

By Bob Robinson

In 1990, the European Space Agency (ESA) initiated a technology transfer program to stimulate the wider use of technology developed by the European and Canadian space communities. This paper focuses on the method of technology transfer from the space industry to terrestrial industries, with a focus on the mining resource sector within a program called the Harsh Environments Initiative (HEI) created in 1997. Other resource sector applications include forestry and oil & gas. C-CORE in partnership with the Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) supported by ESA, Canadian Space Agency (CSA) and European R&D organizations conduct projects to promote and demonstrate the transfer of innovative technologies from space to non-space industries. Space programs have and continue to develop new knowledge for extra-terrestrial application, e.g., satellite earth observation, manned missions and unmanned planetary exploration. Many of which hold the potential for application on land and ocean. Currently, space technologies of interest to the mine sector range from robotics and image analysis to sensors, software and advanced materials. The HEI works to identify and apply these types of technologies in the areas of automated/tele-controlled mine operations and mine monitoring.

May 1, 2001

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid shoring system consisting of cast-in-place soldier piles with Cutter Soil Mixing (CSM) infill panels was constructed for temporary support of a 19.8 m (65 ft) deep excavation in Vancouver, British Columbia, Canada. Deep Mixing (DM) was completed up to 9.7 m (32 ft) in fill, peat, wood waste and clayey silt with embedment in dense till, and soldier piles constructed through the dense till extending to below final excavation level. Two trial CSM panels were installed ahead of production to assist with developing the termination criteria of the CSM panels in the dense till. The constructed depth of the CSM panels was based on interpretation of real-time monitoring data obtained through the Bauer B-tronic system. Inclinometer monitoring data from two CSM panels and two soldier piles, as well as soldier pile survey target data was used to assess and monitor the performance of the hybrid shoring system throughout bulk excavation. The objectives of this paper are to provide an overview of the design and construction aspects of the hybrid DM shoring system and to present inclinometer and pile target data to demonstrate the lateral performance of the CSM infill panels and soldier piles. This paper also discusses the merits of using real-time monitoring data as part of the engineering decision-making process for validating CSM panel construction. BACKGROUND A hybrid DM shoring design was recently completed for a high-rise development in downtown Vancouver, British Columbia for temporary support of a five level basement excavation. Deep mixing was proposed by the excavation and shoring design-build team as the preferred method to construct infill panels between soldier piles because of the speed at which the shoring system could be constructed in variable fill, peat, wood waste and overburden compared with traditional secant piling methods. The development site is generally a truncated triangle in plan, with the longest side of the triangle being approximately 115.7 m (380 ft) long and the two shorter sides being approximately 71.6 m (235 ft) (Hybrid Shoring Wall 1) to 75.0 m (246 ft) (Hybrid Shoring Wall 2) long. The site is bounded by an existing bridge off-ramp structure along its longest side, and by city streets on the other two sides, as shown in Figure 1. The truncated section is approximately 16.8 m (55 ft) (Hybrid Shoring Wall 3) long. Due to project constraints, the hybrid DM and soldier pile shoring system was only proposed for the two shorter sides of the triangle and the truncated section. Traditional secant piles were installed for the longest side. This paper focusses on the hybrid shoring system. A typical detail showing the CSM infill panel with the soldier piles is presented in Figure 2."

Jan 1, 2017

Terminology. The term potash originated in "pot ashes" produced by burning wood to ashes in iron pots and then leaching out the soluble salts, chiefly potassium carbonate, from the residue. In modern usage potash is a generic term for various potassium salts used in agriculture and industry. More specifically, it denotes the oxide of potassium, K2O, and the content of potassium in ores and products is stated as weight percent of K2O present. Its salts are commonly referred to as muriate of potash, sulfate of potash, etc. The presence of an adequate supply of available potassium in the soil promotes the health and improves the quality of the plant. insures greater efficiency in photosynthesis, increases resistance to certain diseases, offsets the effect of an oversupply of nitrogen, and helps the plant to utilize soil moisture more advantageously. ("Soils and Men," U.S. Dept. of Agriculture Yearbook 1938.) Occurrence. Potassium ranks seventh among the elements in abundance. It is estimated to constitute some 2.6% of the lithosphere and is found in soluble forms in the oceans, lakes, rivers, and subsurface waters. It is also an important constituent of plant and animal life. Commercially significant accumulations of potassium salts occur in underground deposits formed in past geologic times by evaporation of ancient bodies of saltwater, inland drainage basins, and shallow sea lagoons. The potash content of such waters was the end result of weathering and leaching of insoluble potash-bearing aluminosilicates, such as feldspars, micas, leucitcs, and others. The concentrations of potassium salts in the natural brines of some lakes in the arid and semiarid regions of the continents are also important as sources of potash; the brines of the Dead Sea in Asia Minor, the Great Salt Lake in Utah, and Searles Lake in California typify such concentrations. Every continent has major potash deposits as listed in Table 1 adopted from Cawley.1

Jan 1, 1985

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

By J. K. Hrica, T. J. Orr, J. Navoyski, B. Macdonald, C. L. Hoebbel, J. L. Bellanca, B. Demich

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos. The videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Feb 1, 2023