Search Documents

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By D Brett

"Mine waste storages including tailings dams and waste rock dumps represent arguably the biggest risk on a mine site from both physical and geochemical viewpoints, related firstly to structural stability and the consequences of failure and secondly from potential on-going seepage or run-off of acid and metalliferous drainage (AMD). The risks are most likely to increase during operations and continue through the closure and post-closure phases, with the waste storages likely to be the most difficult features to resolve in the mine closure process. Contaminated water quality from tailings dams and waste rock dumps can require treatment "in perpetuity" at a cost of hundreds of millions of dollars. The problem is increasing with ever larger mine operations and waste generation volumes. This paper identifies leading practice methodologies in planning and operating mines and process plants to minimise the risks from tailings storages and how this might also affect waste rock management and even the design of mine excavations. These methodologies require a "big-picture" approach to develop an understanding of the overall issues and identify synergies between the different operational areas on a mine site that can reduce overall risk. With a conservative approach and realistic allowance for future costs it is possible to facilitate decisions at the mine planning stage that can reduce risk and save cost over the long term. This is in contrast to the common approach where each operational area is looking to minimise its own costs with a short-term view. Incorrect mine methodologies can be developed by allowing net present value (NPV) accounting methods to trivialise future closure issues.Methodologies discussed include: Integrated Waste Management - Significant structural improvements to tailings dams can be achieved if the structures can be incorporated into the waste rock dumps. Risk of AMD can also be reduced by utilising the tailings and waste rock effectively. This could go even further to consider the placement of wastes to limit mine void environmental issues; Process Optimisation - Water quality and the nature of potential tailings dam structures can be highly influenced by the geo-chemistry of the tailings. This can be modified by processing, where simple changes such as maintaining separate streams of geo-chemically different tailings rather than recombining them or by initiating further processing to remove problematic minerals such as sulphides; Enhancing Geophysical Properties - The geochemical performance of waste repositories can be greatly influenced by the geophysical properties of the stored materials, particularly the air-water characteristics, which are influenced by particle size, density and permeability. The geotechnical properties can be enhanced by strategic paddock dumping, blending and compaction.These methodologies are demonstrated by case histories.CITATION:Brett, D, 2013. Mine waste risk minimisation by integrated waste management and process optimisation, in Proceedings MetPlant 2013, pp 247-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Peter Wells, Adrian Sabau, Turgut Yalcin

"The nickel ores of Sudbury contain substantial amounts of the gangue mineral pyrrhotite (Fe7S&) which causes certain diflculties in the milling of these ores. This paper proposes a process called “magnetoflotation” as an effective means of dealing with pyrrhotite. The method reduces the pyrrhotite content of concentrates by applying a magneticjield on the path product as it leaves the flotation cell.Successful performance of magnetoflotation requires the optimization of several variables. In this study, three of the variables (air flowrate, collector concentration, pother concentration) were investigated by Box- Wilson experimental design, and others (magnet speed, grind size, pulp density, flotation time) were examined individually. The process was tested on a Falconbridge nickel ore, assaying 1.92% Ni, and under the best operating conditions, a concentrate was obtained with 13.56% Ni grade and 74.32% recovery in a single step. Further improvements to grade and recovery were possible by cleaning and scavenging. The same ore was also tested with conventional methods for comparison, and results indicated that magnetoflotation performed better.INTRODUCTION“Magnetoflotation” refers to the process of carrying out magnetic separation and flotation simultaneously within the same device, and is intended to prevent magnetic minerals from reporting to the froth products while non-magnetic minerals are being floated. Typical cases where this method might be beneficial include the processing of magnetite and nickel ores. Its use on magnetite ores has been reported elsewhere [Yalcin, 1992; Yalcin, 19931. This paper describes its application to nickel ores, more specifically to the nickel ore of Falconbridge Limited in Sudbury."

Jan 1, 1999

Major activities of the Bureau of Mines Explosives Research Center during fiscal year 1965 (July 1, 1964, to June 30, 1965) are reviewed briefly. Part 1 summarizes significant accomplishments of the projects that were active during the report period. Part 2 presents short abstracts of the publications that appeared in the Bureau series and in other media during fiscal year 1965. Publications issued after June 30, 1965 are noted where pertinent in footnotes but are not abstracted.

Jan 1, 1966

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

Single particle breakage tests have been used by a number of researchers to investigate some salient features of the complex comminution process. The characteristics of the common single particle breakage tests such as single impact, double impact and slow compression tests are examined and the results from these tests are compared. A comparison of the results from single particle breakage tests with grindability and ball mill tests is given. Application of the results from single particle breakage tests to modelling industrial comminution processes is described. The necessity for further research into single particle breakage tests to develop a simple but comprehensive technique for estimating the breakage characteristics of ores is discussed.

Jan 1, 1986

By Madgwick J. C, Ralph B. J

A method for the determination of microgram quantities of uranium in leachates from low grade uranium ores is described. Solubilized manium is purified by transfer to an organic solvent by a selective solvent extractionprocedure using tributyl phosphate, iso-octane, and aluminium nitrate. The organic phase is mixed with scintillation fiuors in toluene and the radioactive decay determined in a liquid scintillation counter. The method is sensitive and reproducible in the range 3-30 µg uranium.

Jan 1, 1978

By C. A. Ozturk

The compressive strength of rock (sc) has an important effect on design of structures in rock engineering. Compressive strength can be determined in the laboratory using the uniaxial compressive strength (UCS) test. Some other index tests, such as the point load test, are also used, particularly when suitable samples for UCS are not available. The quantification of rock texture has introduced a new method in rock engineering for estimating the mechanical and physical properties of rock materials from microscopic investigations. The aim of this study is to quantify rock texture to estimate rock strength from the texture coefficient (TC), which is determined from a statistical assessment of thin section images. Rock texture is quantified by twelve different images from a single thin section to increase the reliability of texture analysis. A data-set is prepared to investigate correlations between TC and sc. The statistical correlations are computed after classifying of the rock samples based on their lithology as well as grain features. Equations derived based on the results of this study are used to predict the approximate value of compressive strength from the texture coefficient. This method is particularly useful for preliminary studies in rock engineering projects prior to detailed site investigation.

Jan 1, 2014

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By Donald Leroux, Lori Lynn Smith, Robert Hutchison

"The grinding circuit of the Heath Steele concentrator was sampled under five different sets of operating conditions. The balanced results of the sampling campaigns were used to calibrate steady-state rod mill, ball mill and cyclone models using a commercial simulation software package (JKSimMet® ). Thirteen process variables had the potential to affect significantly the performance of the grinding circuit. Statistical-Design-of- Experiments techniques were applied to plan the suite of simulations in order to improve the quality of and minimize the time to find the optimal solution. The effect of each factor on three performance indices (the cyclone overflow size distribution, the circulating load and the cyclone underflow density) was modeled with empirical polynomial relationships using another software package (Design-Expert@)T. he conditions under which the cyclone overflow size distribution was maximized while respecting circulating load and cyclone density constraints were identified using these relationships. Among the most interesting results is the prediction of a set of conditions where the circuit target size distribution is achieved with only three ball mills instead of four.IntroductionProduction at the Heath Steele concentrator (near Miramichi, New Brunswick) started some 43 years ago at a rate of 750 t/d. The plant capacity was increased to 4000 t/d through successive expansion phases in the seventies (Sapiro, 1977; Johnston, 1978). However, as a result of depleting ore reserves, the plant throughput had to be gradually reduced to the current production rate of 2700 t/d. Heath Steele Mines currently have proven and probable reserves which would see it producing until the end of 1999 (Noranda Inc., 1997).An analysis of the grinding circuit of the Heath Steele concentrator was recently commissioned to identify opportunities for reducing operating costs while maintaining budgeted mill throughput and metallurgical performance. Since the plant will likely be operated below nominal capacity for the rest of its lifetime, the possibility of improving grinding efficiency by operating with fewer ball mills and/or crushers was contemplated."

Jan 1, 1999

By Stephen J. Roberts

Gold catalysts were prepared on co-precipitated, calcined copper oxide - zinc oxide support by an inverse deposition-precipitation method. These catalysts were characterised by X-ray diffraction (XRD) and temperature-programmed reduction (TPR) and studied for CO oxidation activity at various catalyst calcination temperatures. TPR studies of the support material exhibited a double peak and shift to lower temperatures for the reduction of Cux+ to metallic copper, as opposed to the single reduction peak for pure CuO. This phenomenon is possibly caused by an interaction with the zinc oxide. The addition of gold to the support CuOZnO led to a further shift in copper reducibility to lower temperatures. Gold present in the initial uncalcined catalyst as Au3+ was auto-reduced to Au0 under various calcination temperatures. The Au3+ reduction peak was observed to shift to lower temperatures with increasing calcination temperature. The catalytic activity was found to pass through a minimum value with respect to calcination temperature. Catalysts with both gold in entirely the 3+ or metallic oxidation state were found to exhibit high activity. Furthermore, the catalysts were found to decrease in activity with decreasing Au3+ content up to an intermediate calcination temperature, afterwhich the activity increased sharply. Possibly at higher temperatures, a stronger Au-support interaction is formed, leading to a new active site.

Oct 1, 2003

By H. F. Weaver

The 17th National First-Aid and Mine Rescue Contest was held in the Kentucky Fair and Exposition Center, Louisville, Ky., October 2, 3, and 4, 1957. The meet was under the auspices of the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with the National Coal Association, United Mine Workers of America, State mining departments, local mining institutes, and coal operators' associations. The Arrangements Committee, as authorized by the General Committee, made all the necessary arrangements for conducting the 1957 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators' Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1958

By Peter Cain

In response to the appearance of excessive convergence of bolted gateroads in the front abutment zone of retreating coal faces at Phalen Colliery, staff from the CANMET Cape Breton Coal Research Laboratory in Sydney, N.S. initiated a programme of roof profile measurements in the front abutment zone of longwall headgates. The results of these measurements allowed a characteristic deformation curve to be determined for each headgate, and the early identification of areas showing an unstable deformation trend. These areas were then reinforced with supplementary support. The monitoring programme was adopted and enlarged by the rock mechanics staff of the Cape Breton Development Corporation, and has been continuing for a period of approximately two years. A sufficient quantity of data now exists to be able to make an assessment of the effects of a number of mining parameters on the performance of the gateroad in the front abutment zone. The following paper describes the method of measurement, illustrated by typical results, and goes on to relate variations in rate and patterns of movement to geology, interaction, method of support and pre-mining stresses.

Jan 1, 1996

By Daniel Hack

A few progressive mining software companies have recognized the benefit of broadening their capabilities to the sand and gravel (aggregate) industry. The most promising new developments have been designed for use with Surpac Vision, one of the world’s leading geological modeling, mine design, and production management systems. Surpac’s broad user-base, who have always had a propensity for customization, are now focusing on development of solutions in the Tool Command Language (Tcl), an interpreted scripting language. Surpac Software International made changes to TCL to add Surpac specific extensions, thus creating the Surpac Command Language (Scl). The Tcl interpreter, including Scl extensions, is bound into the Vision executable to provide a seamless interface to the data objects used internally by Vision, the GUI, and the 3D rendering system. Custom solutions can be incorporated as Vision extensions, or as stand alone-modules used in correlation with modeling, design, and planning functions.

Aug 25, 2002

By E. P. Hayes

This report supplements the date contained in Bureau of Mines Information Circular 6156, "Special features of core drilling in the salt beds of Western Texas and New Mexico," by J. S. Wroth. That circular dealt with the drilling of the first 12 of the 24 potash tests made by the U. S. Bureau of Mines in cooperation with the U. S. Geological Survey; this report is concerned with the drilling of the last 12 tests. ACKNOWLEDGMENTS The writer is indebted to R. E. Heithecker, the Bureau of Mines engineer who had charge of the drilling of tests 13 to 17, for his well-prepared records on the drilling of these tests.

Jan 1, 1933

By Gang Chen

Conventional methods designate a factor of safety, a deterministic number, to indicate the stability of a mine excavation. However, this deterministic description of excavation stability is frequently insufficient or inaccurate and, sometimes, misleading. Employing the probabilistic analysis to determine the likelihood of mine excavation failures will lead to a better understanding of ground control problems and result in more rigorous designs of the excavations. Based on the theory of probability, two approaches are taken in this study for the probabilistic analysis of excavation stability. The first one utilizes direct integrations for the estimation of failure probabilities of mine excavations. Due to the complexity of the integration, this approach can only be applied to solve relatively simple problems. In order to overcome the limitation of the direct integration method, the second approach employs the first-order second-moment approximation of the failure probabilities for more complex ground control problems. The probabilistic analysis offers a deeper insight into the uncertainty associated with the stability of mine excavations. The study indicates that the distributions of parameter values play a significant role in the mine excavation stability, which can not be disclosed by the conventional methods of stability analysis. Greater dispersiveness of the parameter values will lead to a different probability of failure, although the factor of safety estimated by conventional methods stays the same if the mean values of the parameters are constant. By taking consideration of the probabilistic distributions of the parameters, the probability model can provide more reliable designs of mine excavations.

Jan 1, 1996

By M. C. Chapman, P. L. Swanson, A. T. Iannacchione

The National Institute for Occupational Safety and Health (NIOSH) evaluated microseismic activity from three field sites to compare and contrast the characteristics of microseismic emissions from very different geologic, stress, and mining environments. Recently, NIOSH has embarked on a research program to evaluate the use of microseismic monitoring information to identify roof fall failure processes and to assess its potential to warn of unstable roof conditions. Large roof instabilities, such as roof falls and certain roof caving events, have proven difficult to anticipate representing an increased risk to miners working in these inherently hazardous areas. When local failure processes are better understood, appropriate control measures can be engineered to mitigate these hazards. This study used microseismic emissions to help identify three local rock failure processes. It was also shown that analysis of microseismic emissions can aid in assessing the degree of instability associated with these local rock failure processes.

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By F. L. Pirkle, D. L. Pirkle, E. C. Pirkle, W. A. Pirkle

Heavy minerals have been mined from the sands of the United States’ Atlantic Coastal Plain since the early part of the twentieth century. Production of ilmenite from beach sands near Mineral City (Ponte Vedra), Florida, began in 1916. The first reported large-scale recovery of zircon in Florida was reported from this deposit in 1922 and of rutile in 1925. These operations ceased in 1929. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site. In 1942 heavy-mineral operations were established on 202 hectares of land situated in Duval County, Florida. The location is about 16 kilometers east of the center of Jacksonville, Florida, in an area known as Arlington. This operation demonstrated that low-grade sand containing only 2 to 3 percent titanium minerals could be concentrated economically with the Humphreys spiral and that the oxides could be separated from the heavy silicates by electrostatic methods. Much of this area is now covered by a large mall and is a major retail- commercial center. Between 1958 and 1964 the Skinner tract, a deposit about 4 kilometers south of the above deposit, was mined. Today the area of this deposit is known as Deerwood, a gated country club community on the southside of Jacksonville. Further inland, E.I. du Pont de Nemours and Co. has been mining heavy minerals from a physiographic feature known as Trail Ridge since 1948, and a deposit near Green Cove Springs, Florida has been in production since 1972. Since the start of heavy-mineral mining in the southeastern United States, nine heavy-mineral ore bodies either have been or are being exploited in Florida and Georgia. Other deposits either have been lost to mining or are yet to be mined. These deposits have different origins. Some formed along shorelines at the heights of marine transgressions while others formed on regressional beach ridge plains during periods of temporary stillstands or slight transgressions. These different origins are reflected in the chemical and physical characteristics of the deposits. Ilmenite in older, more western deposits has a higher TiO2 content than ilmenite in younger, more eastern deposits. TiO2 content does not very with north-south direction. Garnet and epidote are absent or rare in the older Trail Ridge deposits, but progressively become common in the younger Duval Upland, Crestal Pamlico, and Holocene deposits. Grain size is coarsest for Trail Ridge sediments and finest for sediments in Duval Upland and Crestal Pamlico deposits. The average grain size for Holocene deposits is intermediate between Trail Ridge and Duval Upland deposits. The two models for the origin of the heavy-mineral deposits – deposits formed at the height of major marine transgression; and deposits formed during periods of temporary stillstands or slight transgressions that occur during a general marine regression; - are consistent with known sedimentological data and depositional trends.

Jan 1, 2005