Search Documents

By C. C. Harris

An analytical solution of the integro-differential equation of batch grinding is proposed as a first appoximation to the xYt surface. The size distribution equation (xY plane) is a three parameter equation previously suggested. Possible refinements are outlined. Comminution kinetics research is presently following several related courses. Some are equivalent, in that they represent different ways of viewing the same facet of the problem, though the entire endeavor cannot be described as being completely integrated. The purpose of this note is to propose and discuss a framework into which the various approaches might be fitted. This must clearly be founded upon an analysis of the xYt surface.' (See also Fig. 1 of Reference 26.) The investigations referred to above comprise mainly researches into the following: (1) The kinetics of the creation of the finer sizes during relatively small grinding times. This is the Fahrenwald-Arbiter-Bhrany 2-3 approach which leads to equations equivalent to a special case of the charles4 relationship. It emerges that initial production of fines follow essentially zero order* kinetics. (2) Disappearance kinetics of the coarser fractions. This appears to be a first order relationship.5-6 (3) Prediction of the xYt surface via the selection and breakage functions utilizing computer-programmed or approximate solutions of the integro-differential equation of batch grinding.5,8-17 A recent discussion by Mika et al.5 references the relevant literature up to about 1966. In addition to these main-stream researches there is some work on the minor topic of extremely long grinding time considered as a limiting case.18-19 The field is supported by investigations into the size distribution of fragments produced by breakage processes, some of this work being most valuably statistical-mechanical in nature.20-25 Better fitting equations, however, are obtained by statistical and curve-fitting methods.26 This

Jan 1, 1969

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986

FOR many years past it has been the practice at the Bairnsdale School of Mines to treat any parcels of auriferous concentrates sent in from the surrounding district by roasting them in a handworked reverberatory, and then chlorinating or cyaniding the product. According to Donald CIark, who has done a large amount of work on these ores, the results obtained were fairly satisfactory extractions of over 90 per cent being claimed. With some modifications, the method has been very generally adopted, not only in Gippsland but throughout Victoria. It is, however, difficult to get exact information as to the extractions actually obtained, and unfortunately no records of working results have been kept at the Bairnsdale School of Mines.Having treated several lots of ore by this method during 1907 and 1908 with unsatisfactory results, the writers thought it desirable to make a detailed investigation on some particular ore, both in the laboratory and on a working scale. The ore selectedwas a parcel of low-grade concentrates from Stirling, a small mining field situated about forty miles to the east of Bairnsdale. This ore was chosen chiefly on account of the heavy and inexplicable volatilization loss which took place even on roasting with the greatest care; the loss amounting to between 10 and 15 per cent. In the experiments here related, three main objects were kept in view:-1. To determine with what mineral 01' minerals the gold and silver were associated...

Jan 1, 1909

By M. Rice, M. Stanley, J. Marlow

Arizona construction aggregate industry remains in the crosshairs of public debate, caught between the need for aggregate-based building materials and alternative, high-value land-uses. To better manage lands and improve land-use decisions, the Arizona State Land Department has need for a system to assess potential aggregate resources on State Trust lands, and assign dollar values accordingly. Thereafter aggregate values can be compared to residential, commercial, agricultural, recreational, and habitat values -- in a determination of highest and best land-use.

Jan 1, 2002

By A Unlutepe

The Bosphorus Rail Tunnel Project, located in Istanbul, Turkey, aims to provide a Euro-Asian rail link, via an immersed tube tunnel crossing the Bosphorus Strait, along which will run all commuter, freight and intercity passenger trains of Turkish State Railways (TCDD), as well as the future extension to the European rail network. The total length of upgrading and new railway construction will be approximately 76 km. The main structures include the immersed tube tunnel; mechanised shield tunnels; new Austrian tunnelling method (NATM) tunnels; cut-and-cover, at-grade and retained-cut/fill structures; and some service structures. This paper discusses Phase 1 implementation of the project, one of the major transportation infrastructure projects in the world today, whose varied structures present stimulating engineering and construction challenges.

Jan 1, 2008

By Q. M. Huang

In 1979 our company undertook the project of infra-structural work of White Swan Lake Hotel, (International class ) Guangzhou. Visit to the site showed that it was situated at the riverside, covering an area of 54,000 M2 with 30,000 M2 of which reclaimed from Pearl River. The material used for reclamation was black sand which was dredged from the nearby riverbed. The sand had the properties of high permeability and very low internal friction. The basement of the building was 6.2 m below ground level and 3 m lower than the riverbed. Apart from the pile foundation, a diaphragm wall was to be constructed prior to the commencement of excavation work for basement. A feasibility study was carried out to determine the method of construction which would maximize utilization of the plants and equipment that were available in the execution of the aforesaid foundation works. This report concerns only the construction of the diaphragm wall and the performance of the plants employed. A detailed delineation of the construction method is herein discussed

Jan 1, 2010

This paper sets out to examine the possible relationships between three factors, they are, the rate of growth of world production of minerals, the growth of Australian production and the growth of scientific and engineering knowledge.The first two are quantified, in terms of tonnes and value. The third, an abstract concept "knowledge", requires to be quantified, in terms of manpower.A mathematical model, which has general application, was derived to demonstrate certain axiomatic premises and to define, more precisely, basic concepts related to the philosophy of knowledge.Finally a summary is made of education-cum-industry issues.

Jan 1, 1981

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints ? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints. When complaints come, standard practice is to set up a seismograph in the neighbor’s yard to monitor the blast. Immediately after the blast, the neighbor usually reappears from the house wanting to know the seismograph reading. When told that the PPV was 0.1 in/set, well below damage levels, the homeowner explodes saying “Your machine is wrong”. Perhaps he is right. Understanding why people complain about blasting is not about PPV, it’s all about structural response. People could care less about how much the ground vibrates; they only care about how much their house vibrates. In this paper we will examine the primary factors that control structural response. Through the use of a large array of digital seismographs, the effects of two production blasts on a community surrounding a quarry are studied. The predicted structural response resulting from each blast is calculated at 175 seismograph locations. The predicted response is then correlated to previous research on human perceptibility to vibrations. The results of this analysis and correlation give a better understanding of what the residents actually feel in their homes. The detonations of two single-hole signature blasts are also recorded by the array of seismographs revealing the dynamic characteristics of the geology ‘surrounding the quarry. Once the influence of the geology was understood, blasts were configured to disrupt the natural rhythm of the site through the use of millisecond delays.

Jan 1, 2000

By John Addison

Experimental animal studies comparing asbestos and non-asbestos varieties of tremolite indicate tremolite asbestos is markedly more carcinogenic. By direct analogy, the differences in carcinogenicity between tremolite asbestos and non-asbestos prismatic tremolite should be the same for the other types of amphibole that also crystallize in the asbestos and non-asbestos habits. The earliest of the experiment animal studies, done more than 25 years ago, have design limitations by modern standards including the use of injection or surgical implantation as the route of administration rather than the more relevant route of inhalation. However, the differences in the carcinogenicity of amphibole asbestos and non-asbestos amphiboles are sufficiently large to be clearly discernable even with the study limitations. Together with later studies on these and related minerals, there is strong evidence of a much lower hazard associated with the shorter, thicker fibers of the non-asbestos amphiboles, than is found for the asbestos analogues of the same mineral. It is possible that the non-asbestos amphiboles are no more hazardous than other silicate minerals widely considered nuisance dusts. © 2007 Elsevier Inc. All rights reserved. Keywords: Amphibole; Asbestos; Tremolite; Carcinogenic

Jan 1, 2007

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By J Petrolito

"To improve the economic and environmental performance of underground mining operations, it is common practice to return the metallurgical waste material underground as backfill. This is called hydraulic backfill and is used to fill the mined-out areas not exposed to further mining. To provide mechanical support for underground mining a cemented backfill is normally used. Since its introduction, cemented backfill has allowed mining companies to increase their ore extraction and improve working and environmental conditions. However, cemented backfill represents up to 50% to 85% of the mine’s operating cost compared with 5% to 10% for hydraulic backfill.These economic pressures have led mining companies to carry out research into the partial or total replacement of cement using a variety of alternative materials. The materials are generally site-specific materials, readily available, and cost-effective relative to cement. Such investigations have led to reduced cost of many backfill mixes while maintaining, and in some cases improving, the physical properties of cemented backfill. However, in most cases, cement still remains an integral part of any binder combination. This can be attributed to the alternative binders investigated being either non-binding materials or capable of generating only low-strength backfills, except when used in conjunction with cement.This paper provides a historical review of backfilling binder materials and their characteristics. In particular, it reviews the many alternative materials that have been proposed to either partially or fully replace Portland cement as the main binder."

Jan 1, 2005

Individual specimens of sphalerite from the Broken Hill lode vary considerably in manganese and iron contents, even within the same orebody, so that study of the overall variation of manganese and iron content of the sphalerite calls for the analysis of a large number of specimens. This difficulty has been overcome by analysing a series of recleaned zinc concentrate products, prepared from stope samples and their equivalents, from most of the developed sections of the lode. The analyses reveal that during the formation of the sphalerite the concentrations of iron, manganese and zinc in the mineralizing solutions varied independently of one another from place to place in the forming orebodies, and also in time.The overall pattern of variation of the iron and manganese contents of the sphalerite in the several orebodies of the lode bears a general resemblance to the overall pattern of distribution shown by several other elements, notably, cadmium, lead, bismuth and arsenic. The iron content of the sphalerite indicates that it was formed at a temperature of 6000 C. or higher, but the variation in its iron and manganese contents demonstrates that Kullerud's method for determining the temperature of formation of sphalerite from its iron content must be used with caution if only single specimens of sphalerite are available.INTRODUCTIONThe four chemical analyses available of specimens of practically pure sphalerite from the Broken Hill lode (Table 1) reveal that the manganese content of the sphalerite varies considerably, and that there is a significant variation in its iron content. The variations revealed between individual specimens within the same orebody in the same mine suggest that specimen material is unsatisfactory as a basis for studying the overall manganese and iron contents of Broken Hill sphalerite, unless a great number of specimensis analysed.

Jan 1, 1956

Over the last three decades, the mining industry has been moving towards more underground mechanized mining methods and the number of LHD vehicles utilised has increased. The growth of mechanization and automation has benefited both workers and the mining companies. However, due to the design of the LHD vehicle and the limitations of the operating environment, restrictions to operator visibility are inevitable. The inability of the equipment operator to see clearly (i.e. people, objects or hazards) around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, visibility assessments for existing machines are traditionally completed in the field using a light filament technique. Past researchers have used the light filament technique to collect obscuration zones around the equipment and to produce a 2D chart of this information. The 2D shadow diagrams have proved to be useful in highlighting potential equipment problems and have been performed repeatedly to show the potential of redesigning a part of the LHD for improving visibility. The light filament method involves manually collecting data and requires a level of judgment to be used. As a result the method is susceptible to errors and requires around three hours to complete. The objective of the current research is twofold; firstly to develop a rapid method for field visibility data collection using a laser scanner and secondly to compare results of repeat tests for both light filament and laser scanning methods. A MENSI GS100 laser scanner along with Pointscape and 3Dipsos software has been used to collect visibility information and process the data. The research aims to develop the laser scanner as a technique to rapidly evaluate the visibility profile of an LHD vehicle. Machine design changes can then be assessed quickly using these results.

May 1, 2004

By M. A. Reyes, L. Yan

Heat and humidity buildup withn refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a lifesustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ.

By E Lounejeva, J A Halpin, A Chappaz, D D. Gregory, S Wu, T Lyons, P J. Sack, R R. Large, S W. Bull

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Newly published models suggest that some orogenic and Carlin-style gold deposits formed by the remobilisation of trace elements during interaction with hydrothermal or metamorphic fluids from early sedimentary pyrite that was enriched in Au, As and Te. The released trace elements are transported by the fluids to favourable trap sites where they are deposited. Therefore, early enrichment of Au, As and Te in source rocks (particularly in pyritic black shale) can be crucial to the formation of orogenic and Carlin-style gold deposits.The most important cause of the enrichment of gold and other trace elements in the sedimentary basins has been examined in this study to determine which basins are the most prospective for the development of orogenic gold deposits. An important influence for Au and other associated trace element accumulation in sedimentary pyrite is the temporal variation of trace element content in the oceans, as revealed by a database of over 1400 analyses of pyrite from black shale through geologic time. It is inferred that sediments coeval with those where sedimentary pyrite is enriched in Au and associated trace elements are more likely to be source rocks of orogenic and Carlin-style gold deposits.Factor analysis of the trace element content of pyrite through geologic time was conducted to investigate the multivariate relationships amongst trace elements and how these chemical factors explain the uptake of trace elements. One important factor includes Te, Au, Pb and Bi content. The incorporation of these large cations into pyrite is enhanced by As3+ substituting for Fe in pyrite lattice. The As3+ ion occurs in relatively oxidised environments and, thus, it is expected that shales deposited in non-euxinic waters are better source rocks for orogenic gold deposits.The examination of both the time in which the sediments were deposited and the redox conditions of the basin, and the ocean more broadly, can be used as a guide to approximate the extent of a basin’s fertility. To illustrate the use of this exploration tool, examples from the unmineralised Jet Rock Formation (UK) and the mineralised Castlemaine Group (Bendigo, Australia) are presented in this paper.CITATION:Gregory, D D, Large, R R, Halpin, J A, Lounejeva, E, Wu, S, Bull, S W, Sack, P J, Lyons, T and Chappaz, A, 2015. Accumulation of trace elements into black shale – how to identify a viable source rock for orogenic and Carlin-style gold deposits , in Proceedings PACRIM 2015 Congress, pp 59–64 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Taegong Ryu

Nanosized tungsten powder was synthesized by the hydrogen reduction of ammonium paratungstate (APT) in thermal plasma. The effects of operating conditions on the product composition and particle size were investigated. The particle size of synthesized W powder was less than 30 nm in all cases tested. The sintering behavior of the synthesized powder (25 nm average size) was then investigated and compared with those of commercial W powder of 500 nm average size and W powder of 23 nm average size produced by milling the commercial powder. The sintering was done at 1400oC with various holding times. The hardness of the resulting compact from the synthesized W powder (315 VHN) was similar to that from the milled W powder (309 VHN), but the plasma-synthesized powder had a much lower tendency to form cracks. The compacts of both nanopowders were significantly harder than that of the commercial powder (192 VHN).

Jan 1, 2009

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By Leigh J. Wardle

This paper describes a numerical method for calculating the three¬-dimensional stresses and displacements induced by tabular excavations in a rock mass consisting of parallel layers of distinct material properties. The method is based on the superposition of numerical solutions for elementary displacement discontinuities in a parallel layered rock mass. The method can be used to analyse complicated excavation layouts such as those encountered in room-and-pillar or longwall mining. The method can automatically take into account the effect of the earth's surface. The method offers an economic and efficient solution to stress analysis problems which cannot be adequately modelled using two¬-dimensional methods and for which the expense of three-dimensional finite element or general boundary element analysis cannot be justified.

Jan 1, 1984

By Mills R, Shannon W. T, Finch J

As an extension to investigations into methods of upgrading the Iitania content of ilmenite concentrate from beach sands using 100 g/day, a small pilot plant treating 23 kg/ day of ilmenite was used.In the pilot plant the iron oxide in the ilmenite was reduced to iron at 1200°C using carbon (coal/char) without melting the material, using a tunnel kiln heating cycle, the charges contained in saggars, The iron was then separated from the titania fraction by ball milling, wet magnetic separation, and screening. The resulting magnetic product was high in iron (about 80 per cent Fe) and the non-magnetic product high intitania (about 70 per cent TiO2).From this trial sufficient data were obtained to enable the preparation of a flow sheet for a plant producing 62,300 tonnes/year total products, and an estimate of costs to be made. This has shown that for an estimatedcapital expenditure of nearly $6,000,000 and annual production costs of about $4,000,000, the cost per tonne of high titania product (76 per cent TiO2) would be nearly $70.

Jan 1, 1977