Search Documents

By Nathan C. Rockwood

THE title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. DEFINITION OF MINERAL AGGREGATES "Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without portland cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. Mineral aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theoretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. EXPLORATION AND POSSIBILITIES OF DEVELOPMENT The distribution of deposits of mineral aggregate is universal, since almost any part of the earth's crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (1) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engineering talent in its operating branch, but it lacks, to a considerable

Jan 1, 1943

By R Simcock

Why Rehabilitate? Legislative Requirement Land rehabilitation is a condition of resource consents for mining. Clause 17 (1) of the Resource Management Act 1991 (duty to avoid, remedy, or mitigate adverse effects) provides the legislative basis for local authorities to impose resource consent conditions requiring land to be rehabilitated to approved uses during and after mining.

Jan 1, 1997

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 µm voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Franz-Werner Gerressen

"The use of soil improvement to utilize areas, which are not suitable for foundation purpose, has a long tradition. Due to the increasing demand of foundation works in areas of unsuitable soils, the improvement of the existing soils becomes even more important in the future.Various applications and systems for various demands exist around the world. Either it is a “simple” improvement for settlement reduction or a more important aim as liquefaction mitigation. However, each system has its advantages, limits and needs.Furthermore to the soil improvement, using various tools, soil mixing can also be used for applications like cut off and/or retaining wall.The paper will describe some basics of various techniques and different applications of the systems all over the world where the systems provided solutions for different purposes, e.g. simple foundation or liquefaction mitigation.It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONSoil mixing is a methodology where the soil is improved by mixing it with cement, lime or other binders in situ by using a mixing tool. This methodology can be used either as wet mixing or as dry mixing. In the more frequently used wet mixing process, usually a mixture of binder and water, maybe with additives, is injected and mixed with the soil. Depending on the type of soil and binder, by the end of the mixing process, a mortar like mixture is created which hardens during the hydration process. In the dry mixing process, the binder is directly mixed with the soil and reacts directly with the existing soil and water.Mixing tools show several versions, so that they are mixing around either a vertical or horizontal axis, mixing in a trench and maybe are jet assisted. Figure 1 shows a classification done by Bruce 2010. Depending on the technique, improvement depth of up to 80 m can be achieved."

Jan 1, 2017

By J Hall, A Gallardo, M Strizek

Mineralogy and coproponents Sino Iron, International Minerals and Austeel are in the process of developing four world class magnetite iron ore mines with multiple open pits along a 25 km strike length of Brockman Iron Formation to the south of Cape Preston on the West Pilbara coast. The close proximity of the proposed pits raises some challenging project approvals and environmental management issues relating to the impacts of dewatering at individual projects and the cumulative impacts of progressive development on local and regional groundwater resources, which includes a large fresh water aquifer system in the Fortescue River alluvium.This paper presents an outline of the hydro-environmental impact assessment process adopted and the key result that the cumulative impacts of dewatering at all four projects on the local brackish groundwater system in the basement rocks is only marginally more than the impact of any one project on its own, and that the impact on the Fortescue River alluvium aquifer is negligible. The paper also presents an outline of the proposed integrated water management approach that will involve coordinated monitoring, ongoing impact assessment and management, and reporting programs for all projects.

Jan 1, 2009

By A. T. Jakubick, A. MacG. Robertson

This paper reviews key issues related to the placement of dry (soil) covers on extremely weak, compressible fine tailings. The design and construction of soil covers on such tailings often presents a formidable challenge to the geotechnical as well as the environmental engineer due to the low shear strength, poor traffic ability, and high settlement of under consolidated tailings at the time of reclamation. The geotechnical issues to be considered include: (1) consolidation of near-surface tailings to achieve strength gains, improve traffic ability, and allow safe placement of initial cover layer; (2) stability of tailings slopes during dewatering of tailings ponds and/or cover placement; and (3) long-term settlement of tailings and its impact on cover integrity and final surface shaping. The environmental issues to be considered include: (1) management of contaminated (free) pond water; (2) management of contaminated pore water expelled during tailings consolidation; and (3) management of (uncontaminated) surface water on top of the cover. This paper summarizes recent experiences gained in a large uranium tailings reclamation project. It is concluded that a careful consideration of both geotechnical and environmental issues during the planning stages greatly reduces the costs and environmental risks associated with fine tailings reclamation.

Jan 1, 2000

By R Handfield, G Kary, Frieda Project

Recent exploration by the Cyprus Amax-Highlands Pacific-OMRD Joint Venture at the Frieda River project, PNG has demonstrated the extent of igneous phases, alteration and mineralisation, and the relationships between the various mineralisation styles in this major Cu-Au porphyry-epithermal system. The project area is in the obducted volcano-sedimentary section of the New Guinea mobile belt 78 km NE of Ok Tedi. It is between two major NNE dipping faults interpreted to have undergone thrusting then sinistral shear in the Late Miocene to Recent. The Frieda River Igneous Complex is a 15 km +7 km ovoid area with a central pod of basaltic andesite volcanics with cogenetic diorite to quartz diorite subvolcanic intrusions, and flanking clastic sediments. A series of late-stage, hornblende quartz diorite plugs ring the main igneous mass. The igneous rocks have a normal K calc-alkaline character with a very limited compositional variation. The intrusives are exposed on the eastern flank of the complex and have five mappable units and numerous defined phases. The southeastern quarter of the complex is host to a cluster of at least seven stockwork porphyry copper and skarn-hosted deposits within an area of 4.5 +3.5 km. The Horse-Ivaal and Koki deposits have identified resources totalling 804 mt @ 0.46 per cent Cu and 0.3 ppm Au, and the other deposits are in various stages of exploration. All these deposits are related to the Horse Microdiorite phase of the Complex and are outlined by a zone of potassic-propylitic-SCC alteration. Local overprinting argillic and advanced argillic alteration is related to a separate, post-porphyry mineralisation intrusive phase. The recent emphasis has been on the identification of higher-grade zones using ideas of structural control and specific intrusive-alteration-mineralisation relationships within the known resource areas. An elongate area 13 km x 4 km in the centre of the Complex has advanced argillic alteration in the volcanic rocks. This alteration zone hosts the Nena deposit (52.8 mt @ two per cent Cu and 0.7 ppm Au) and approximately 20 prospects of high sulphidation type. These deposits are distributed along two prominent NW-trending siliceous ridges interpreted as regional scale structures. Nena is a pod of vein and replacement sulphides hosted in a tectonically controlled multiphase breccia that overprints the advanced argillic alteration. The Nena deposit is 4 km from the nearest of the major porphyry occurrences. It is underlain by basemetal veins and minor porphyry mineralisation that are related to the Flimtem Trachyandesite intrusive phase. The recent search for additional Nena-type ore has focussed on the siliceous ridges using detailed structural and geochemical ore control criteria. Widespread, but poorly mineralised, basemetal-bearing carbonate and sulphate veins form a ring around the mineralised area. These veins have sericitic selvages, cut the porphyry mineralisation, but are cut by and locally underlie the silica-alunite phase of the advanced argillic alteration. The current model is that there are discrete intrusive phases responsible for each of major hydrothermal events at Frieda. These include from oldest to youngest:the Koki phase has no related alteration or mineralisation; the dominant Frieda phase has the hornfels, early skarn and minor magnetite-chalcopyrite mineralisation; the Horse phase has the bulk of porphyry copper and skarn-hosted mineralisation and minor basemetal veins; the peripheral Knob phase is barren; and the Flimtem phase has the high sulphidation epithermal deposits and minor porphyry and vein mineralisation. The intrusive phases span the interval 17 to 11.5 Ma and are co-magmatic. They represent discrete batches off the parent magma, rather than simple fractionation products.

Jan 1, 1999

By Pengfu Tan

A thermodynamic model has been developed to predict the distribution behaviors of Cu, Fe, S, O, Pb, Zn, As, and heat balance in a lead blast furnace. The modeling results have been validated by the plant data of a lead smelter in Asia. The model can be used to predict for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen-enriched air. The effects of the blast air, industrial oxygen, and coke charge on the distributions of Cu, Fe, S, O, Pb, Zn, As, and heat balance, and on the lead loss in slag have been presented and discussed.

Jan 1, 2005

By H. Gumede

The occurrence of fracturing due to high stress levels is a major factor in hangingwall stability in deep level gold mine stopes. However, rock falls cannot be the result of these fractures alone. Rock falls can result only from the occurrence of unstable rock blocks defined by the interaction of the stress induced fractures and naturally occurring geological planes of weakness. These planes include bedding planes and joint set planes. However, there is a general lack of information on the characteristics of these planes (orientations, spacings and lengths)?it does not appear that any such systematic and quantified information, if collected, has been published. To remedy this situation to some extent, joint mapping exercises have been carried out in several geological environments in two gold mines. The data collected on joint geometry included orientation, spacing and length, and this information is included in the paper. In addition, the paper describes the use of the data collected to evaluate the potential for rock falls and the probability of failure of stope support

Jan 1, 2007

By K. N. Panigrahi

India bestowed with 6000km of the coastal belt, contains some of the richest and largest placer deposits with a mixture of heavy minerals like ilmenite, rutile, leucoxene, zircon, monazite, sillimanite and garnet. Each of the minerals is having economic value due to its inherent characteristics for industrial use in fields of paints, metallurgy, refractory, abrasive and so on. The reserves of titanium bearing minerals (ilmenite, leucoxene, and rutile) in the country is around 378 million tonnes. More than 90% of the titanium based minerals produced worldwide are utilised for making value added products in the pigment industries. Approximately 8 million tonnes of monazite reserves are available in the country from which several rare earth elements like cerium, neodymium, lanthanum, yttrium etc. can be extracted for use in several industries. The country contains a deposit of about 20 million tonnes of zircon, which is used in foundries, refractories, ceramics and chemicals. India has a reserve of 107 million tonnes of garnet and 131 million tonnes of sillimanite required for the abrasive and refractory industries respectively. Keeping in view the multifarious uses, the beach sand minerals are being exploited to have the economic growth of the nation. Although the process adopted for the separations are simple, the equipment involved are specially designed because of the nature of the material of construction. Starting from the spirals to magnetic separators, all equipments are manufactured outside India, which is not only costly, but the availability also takes much time for fulfilling the import formalities. Unlike open cast mining, beach sand mining is a environment friendly mining because dredging is implemented to cut and pump the loose sand through a slurry pump causing less damage to the surface topography as both mining and backfilling takes place simultaneously. Therefore all out efforts are made to explore the beach sand placer deposits in an economic manner to emerge as a leader in the global mineral industries.

Jan 1, 2005

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of “but which formula is the right one?” The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: • Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) • Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) • Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009

By Jarek Jakubec

The new euphoria in diamond exploration brings with it a need to understand the challenges that new projects can face in different stages of the development and risks that the commercial outcomes from the new projects fall short of expectations. In many cases, the problems are related to a poor understanding of the technical risks and a failure to adequately address them during the course of investigation. Failure to evaluate all disciplines to the same level of certainty could lead to a situation where the important issues are only identified late in the project development, resulting in costly delays and financial difficulties. The diamond projects located in Canadian Arctic, with its challenging environmental, geographical, social, political and geological contexts are especially sensitive to the high variability of the outcome. This presentation highlights some of the technical aspects that could be the leading sources of risk in diamond projects and could ultimately result in inappropriate mine designs, reducing the economic outcome.

May 1, 2006

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005

By M. Ramström

"In 2002, Atlas Copco Rock Drills AB released the new rig control system (RCS) technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging, reduction in manpower in some types, and serviceability have all taken a quantum leap forward when compared with previous generations of drill rigs. RCS is modularized and distributed by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions."

Jan 1, 2005

By Esher Hsu

Keywords: Recycling, Consumer Battery, Fee rates On November 11, 1999, all types of spent consumer batteries are proclaimed to be collected in Taiwan. Under current recycling system, all producers and importers of consumer batteries have to pay a collection/recycling fee to the Recycling Management Fund (RMF) of EPA based upon the rate approved by EPA. Collectors and recycling plants receive subsidies from RMF according to the collected and treated amounts audited by an independent auditing organization. Collected spent consumer batteries only reached 923 tons in 2002 equivalent to 10% of the total quantity sold at the same year. How to increase the collection efficiency of used batteries becomes an important issue for EPA in Taiwan. The objective of this study is to explore current recycling system of spent consumer battery in increasing collection efficiency. Results provide some suggestions to Taiwan EPA regarding recycling route, recycling system, recycling rates, and recycling subsidies.

Jan 1, 2005