Search Documents

By F. W. Jessen, James N. Howell

The accumulation of paraffin deposits in tubular goods has been recognized as a major production problem since the inception of the petroleum industry. This problem is not limited to any particular geographical area nor is it limited to a specific type of crude oil.' Generally speaking, "paraffin" deposition pertains to the deposition of any predominately organic material in flow lines, and possibly even at the sand face, which would hamper the production of oil. In some fields, a continuous effort is required to remove deposits of paraffin and in order to accomplish this, many unique methods have been devised. The best solution to this problem, however, is to prevent the formation of such deposits. One method which has been tried in a number of fields is the use of plastic pipe. The purpose of this investigation is to compare the relative effectiveness of several plastic materials to aid in the reduction or prevention of paraffin accumulations in surface flow lines. COMPOSITlON OF PARAFFIN DEPOSITS By definition, paraffin deposits are those materials which are insoluble in crude oil at the prevailing producing conditions of temperature and pressure. Such deposits1 s usually consist of small particles of petroleum wax intermixed with resins, asphaltic material, and crude oil. They may also contain a variety of foreign materials such as sand, silt, water, various metal oxides, sulfates and carbonates of iron. barium, and calcium. The petroleum waxes deposited in flow strings usually consist of both a "hard" and a "soft" wax fraction. These waxes are largely aliphatic hydrocarbons with smaller amounts of aromatic and naphthenic compounds. Nathan' has classified the hard and soft wax fractions. The aliphatic hydrocarbons present are those of high molecular weight with high melting points. Reistle3 pointed out that these high molecular weight compounds first separate from the oil due to a sharp decrease in solubility as the melting point increases. The identification of the resins and asphaltic materials rests, at present, on an arbitrary solubility procedure. Under certain conditions, materials which are insoluble in pentane (ASTM D-893) are defined as resins and asphalts. Subgrouping of these materials is made on decreasing solubility in benzene and carbon disul-fide. Shock' found some correlation be-tween the solvent response and the pentane insoluble content of paraftins: higher pentane insoluble fractions are less soluble in any of the commonly used commercial solvents. PARAFFIN CONTROL METHODS The methods used in oil fields to prevent and remove paraffin accumulations can be grouped into four general classes: (1) operative methods, (2) physical methods, (3) chemical methods, and (4) combination of any of these. Operative methods attempt to prevent the formation of paraffin deposits while the other methods are concerned primarily with the removal of these deposits. Plastic coated pipe has been used for a number of years to prevent cor- rosion in wells, and in manv instances paraffin deposits have -been greatly reduced. Field observations have indicated that plastic coated pipe not only reduced paraffin accumulation but in some cases eliminated deposition completely; however, data are needed to demonstrate the relative effectiveness of plastic materials. Deposition Apparatus The pipe used to determine the effect of velocity on rates of deposition was %- and 2-in. nominal diameter, and 5 ft in length. Steel, butyrate, rigid PVC, kralastic resin-type plastic pipes, epoxy coated pipe, PVC lined glass fiber pipe, and aluminum pipe were tested. Steel pipe was used as a control. Fig. 1 is a schematic diagram of the apparatus showing the relative position of the separate units making up the equipment. In order to facilitate the installation and removal of the test pipes in the apparatus, O-ring seals capable of sustaining pressures of 50 psi were provided at each end. Test pipes were submerged in a cold water bath maintained at or below room temperature by circulating water through copper cooling coils packed in ice. A hot water bath equipped with immersion-type heaters, stirrers, and a thermoregulator was used to maintain the temperature of the oil prior to introduction into the piping manifold. The capacity of the oil reservoir was 30 gal. A 33-gal/min centrifugal pump, capable of producing turbulent flow velocities in the test pipes, was used to circulate the oil through the system when using %-in. pipe; and a 70-galjmin centrifugal pump was used in later tests using 2-in. pipe. A by-pass arrangement made it pos-

By F. L. Wolf

THE catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This' means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a, preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of, materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though its importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation.

Jan 1, 1930

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.' The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965

By F. C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of transporting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion. FIXED-SOURCE METHODS Essentially, a fixed-source method consists of the measurement of electromagnetic fields about the source. The mutual coupling between the source and the earth is constant, but the mutual coupling between the receiver and the earth (unless the earth is homogeneous) and also between the source and the receiver changes at each station. The results are usually normalized by relating the field data to the calculated free space or primary field. Turam and Radio Reference Signal Methods: The turam or two-frame* (see Fig. 1A) is probably * Turam means two-coil. the most common fixed-source method. The energizing source is an insulated cable grounded at both ends or formed into a large rectangular loop. Measurements are taken along a traverse at 5 to 50-meter intervals using two small receiving coils, the lagging coil being placed at the position previously occupied by the leading coil. The complex ratio (i.e., inphase and out-of-phase ratios) of the voltages induced in the two coils is measured. Operating frequency range is about 100 to 800 cps. In a typical turam survey a straight, grounded cable several kilometers long is laid out parallel to the probable strike of the ore deposits or conducting strata being sought. An area extending 1 or 2 km on each side of the cable, and within 1 or 2 km of the ends of the cable, is surveyed. Measurements are made at stations 5 to 25 m apart along traverses perpendicular to the cable. Measurements may be made along lines parallel to the cable to serve as base lines for the traverses or for other special purposes. Commonly the receiving coils are oriented with their planes horizontal so that only the vertical component of the field is measured. If additional information is required, one of the hori- zontal components may also be measured by orienting the coils with their planes vertical. In a modified turam technique developed recently for both ground and airborne measurements (Fig. 1B) the amplitude of the complex voltage induced in a single receiving coil is measured and its phase compared with that of a reference signal transmitted from the energizing system by a radio frequency carrier. Thus the un-normalized field is obtained directly, whereas with the turam method it is obtained by calculation from the ratios. The turam method and its modifications have a greater working depth than the other electromagnetic procedures used in ore prospecting. Under favorable conditions conductors have been located at depths of 200 to 300 m. A modified turam method with one of the electrodes grounded in the upper end of a plunging orebody was used to follow the extension of this body to a depth of 200 m beneath a layer of conducting schists. Straight grounded cables are usually preferred to insulated loops because they are easier to lay out and because they often make the method more sensitive. The greater sensitivity of a grounded cable is a result of ground return currents which may flow in the orebodies in addition to the eddy currents caused by induction from the current in the cable. Anomalies in the vertical field due to eddy currents are characterized by a correspondence between high values for the inphase component and positive out-of-phase components and/or low values for the inphase component and negative out-of-phase components. Also the inphase component may approach zero, but it does not become negative. In very long continuous conductors that are parallel to a grounded cable the effect of ground return currents may far exceed the effect of eddy currents. These ground return currents cause a lack of correspondence between the inphase and out-of-phase components and may cause negative inphase or anti-phase components. It becomes difficult to carry out the measurements and often difficult to interpret the results. Such results immediately suggest the presence of graphitic strata, however, since ore deposits are rarely extensive enough to accumulate sufficient ground return current to cause these results. A cable laid out perpendicular to the strike or an insulated loop is sometimes used in areas where graphitic schists and slates are present. Anomalies are then completely or almost entirely due to eddy currents and are easier to interpret. The measured voltage ratios are normalized by either subtracting or dividing by normal field ratios calculated from free space considerations. The normalized ratios are then plotted as individual profiles. When significant anomalies occur in the ratio measurements, the actual normalized fields are calculated by beginning with a measured or an assumed value for the field at a point near the cable and successively multiplying this value by the normalized ratios. There is a similarity between this process and a numerical integration of the ratio curve. Conversely, in many respects the ratio curve is similar to the first derivative of the field curve.

Jan 1, 1960

By H. A. Meyerhoff, R. J. Colony

Deposits of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residual limonite at the west end of the island near Mayagüezl-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7"9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugües, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By J. J. Jonas, G. Gagnon

SHG zinc was extruded in the temperature range 110" to 350°C and the strain rate range 0.05 to 5 sec-1 The strain rate/flow stress/temperature results were analyzed using a power sinh stress relationship. When temperature changes due to the heat of deformation and to heat losses are neglected, the exponent of the sinh function of the stress is 5.6, and the apparent activation energy of deformation is 28 kcal per mole. When these changes are taken into account, the exponent decreases to 4.7 and the activation energy to 23 + 2 kcal per mole. The corrected stress exponent and activation energy are in very good agreement with published values obtained from creep experiments, and suggest that the hot extrusion of zinc is controlled by a mechanism involving self-diffusion. When the extrusion and creep data are compared using a Zener-Hollomon parameter and either a sinh or an exponential stress term, an appreciable offset is observed, which may be due to the difference in impurity content. For a given set of extrusion conditions the ram speed, maximum pressure, and initial temperature can also be correlated using a Zener-Hollomon parameter and a sinh pressure term. THE deformation of metals at temperatures over about one-half the absolute melting temperature has been extensively studied at creep strain rates. By contrast, relatively little work has been carried out on the behavior of metals at hot working strain rates. Most of the latter investigations have been performed using simulative methods, such as hot torsion and hot compression, in which the friction conditions and temperature rise during deformation may differ appreciably from those existing under industrial conditions. Recently, however, Wong and Jonas1 used a scaled-down industrial process to determine the stress and temperature dependence of the strain rate during the extrusion of aluminum. In such tests, the effects of friction and adiabatic heating are closer to those produced in industrial operations. Also, with regard to the testing of materials of limited ductility such as zinc, hot compression and hot torsion do not permit the attainment of true strains as large as the deformations usually applied commercially. The present study was undertaken to investigate the extrusion behavior of Special High Grade (SHG) zinc. The detailed objectives were: 1) to establish the stress and temperature dependence of the strain rate with and without a consideration of adiabatic heating, 2) to study the pressure and temperature dependence of the ram speed, and 3) to investigate the microstruc- tural changes occurring during the deformation. The last aspect of the investigation will be covered in a separate paper. The treatment described below differs from that of Wong and Jonas in that the adiabatic temperature rise during deformation is taken into account, and the calculation of the mean equivalent strain rate is based on the redundant as well as on the homogeneous work. EXPERIMENTAL PROCEDURE Rods from two shipments of continuously cast SHG zinc* were used in the investigation. The composition *Supplied by courtesy of Cominco Ltd. range of the impurities present, as given by the supplier, was: Pb: 0.0013 to 0.0023 pct, Fe: 0.001 pct max Cd: 0.0001 to 0.0006 pct, Cu: 0.0002 to 0.0005 pct, Ti: 0.0001 pct max; thus, by balance, zinc valued from 99.9963 to 99.9966 pct. The as-received rods were machined into billets having a nominal diameter of 1.56 in. and a nominal length of 1½ in.; longer billets up to 4 in. in length, were also used to investigate special aspects. The as-machined rods were annealed at 400°C for 24 hr and slowly cooled. This treatment produced a columnar grain structure, with a grain size of about $ by 2½ cm which was appreciably larger than the as-cast one. A 150-ton, direct extrusion, vertical press was used. Ram displacement and force were recorded continuously against time. A constant flow control valve permitted the maintenance of a range of preselected ram speeds up to in. per sec. The selected speed was held constant, irrespective of the required force, as long as the load developed was below the maximum available. Strain gages were used to determine the force; the gages were calibrated before and after each testing period with a 200,000-lb capacity load cell. Further details of the experimental equipment can be found in Ref. 2. The billets were preheated for 90 min in the extrusion container, which was well insulated so as to minimize temperature gradients. This period was sufficient for the billet to reach a uniform temperature at all temperatures between 110" and 350°C. A square-shoulder die having a 0.290-in. diam central hole was used. The extrusion ratio was 30 to 1. This is equivalent to a reduction in area of 96.7 pct, an elongation of 2900 pct, and a true strain of 3.4. The ram speed was varied over two orders of magnitude from 0.0027 to 0.26 in. per sec. The ram was water-cooled during most of the tests, although some experiments were conducted with a preheated, uncooled ram. All extrusions were run without lubricant, which resulted in conditions of sticking friction. EXPERIMENTAL RESULTS Stress Dependence of the Strain Rate Neglecting Adiabatic Heating. The maximum force required to extrude is given in Table 1 for each of the five initial

Jan 1, 1970

By J. A. Grimes, Paul Billingsley

A. Introduction. 1. Association of Ores and Igneous Rocks. 2. Identity of Granite Rocks. B. General Geology. 1. Geologic Events of the Igneous Cycle. 2. Association of Igneous Intrusions with Tectonic Forces. C. Igneous Rocks. 1. Andesite Period. 2. Granite Period. (a) Diorite. (b) Quartz-Monzonite. (c) Aplite. (d) Quartz-Porphyry. (c) Quartz-Veins. 3. Rhyolite Period. 4. Comparative Analyses. D. Classification of Deposits. 1. Genetic Classification. 2. Parallelism Between Igneous Stages and Stages of Ore Deposition. Part 2.—The Ore Deposits Andesite Period. A. Andesite Phase. 1. Disseminations—Baggs Creek. 2. Contact Deposits—Iron Mines of Ekhorn Mountains. 3. Fissure Veins—Emery District. (a) Fissure Veins in Andesite Walls. (b) Mineralization Along Bedding of Flows. (c) Mineralization of Amygdaloidal Lavas. (d) Mineralization of Breccia. 4. Summary.

Jan 1, 1918

By M. C. Fuerstenau, R. B. Bhappu

The response of beryl to sulfonate flotation was examined. The dependence of flotation recovery on sulfonate concentration, pH, and the absence or presence of various ions is also demonstrated. The response of quartz and feldspar to sulfonate flotation at various values of pH is given to. show the conditions necessary for selective separation. Finally, beryl was successfully concentrated from a natural ore using a technique devised from experimental observations on systems of pure minerals. With the possible exception of quartz, the flotation characteristics of silicate minerals are rather poorly understood. This is due in part to the com- plexity of the mineral systems themselves and in part to an insufficient amount of flotation data. The complexity of the systems arises from the wide range of chemical composition that the silicate minerals can assume. This is reflected in the variability of such physical properties as hardness and cleavage. Although the chemical composition of silicate minerals can vary considerably, a general grouping can be accomplished conveniently on the basis of the assemblage of SiO4 tetrahedra in all the silicates. That is, it has been shown that six basic groups can be obtained, depending on the arrangement of oxygen sharing between adjacent silicon atoms (or substituted aluminum). When all four oxygen atoms are shared, a framework structure such as quartz or feldspar is obtained. When three oxygens are shared, infinite sheets are obtained as in the micas and clays. When two oxygen atoms of the tetrahedra are shared, infinite chains are obtained, such as those in

Jan 1, 1963

By Hugh Roberts

During 1916 and 1917, the E. J. Longyear Co. of Minneapolis, Minn., carried out a campaign of exploration for nickel-copper ore in the Sudbury District of Ontario. The work was initiated by W. E. Smith, a resident of Sudbury, who called the attention of W. J. Mead, Chief geologist. The E. J. Longyear Co., to the fact that explorable lands in the Sudbury District were still available. Five diamond drills were employed, and holes were drilled in the townships of Levack, Trill, Denison, Blezard; Garson, Falconbridge and MacLennan. The general map of the District, Fig. 1, shows the distribution of the lands chosen. As a result of this exploration, a large body of nickel and copper ore has been found in the western part of the Township of Falconbridge. This property lies in the eastern part of the Sudbury District, east of the Garson mine.

Jan 2, 1918

By R. W. Kraft

A back- reflection precession-type X-yay camera for determining the crystallographic orientation of the crystallites of both phases in small areas of thick specimens of polyphase alloys is described ad the geometry, advantages, and limitations of the apparatus are discussed. Metallographic obseg-vations of interfacial angles (or habit planes or growth direction are made on the same specimen so that the crystallographic and metallographzc orientation data call be directly correlated. An example of the application of tile technique to a unidi-~~ectionally solidified CuA12-A1 eutectic specimen is presented. The interfacial planes ad growth directions of each phase were established, and the orientation relationship between the phases was observed and found to be approximately intermediate between two previously reported relationships. The crystallographic interfacial relationship between two solid phases is an important parameter in a variety of metallurgical phenomena because of the energy associated with the interface and because this energy is at least partly associated with the way in which the two space lattices are in contact along the interface. In order to describe the interfacial planes in the crystallites of both phases it is necessary to determine the crystallographic orientation of each phase in a specimen relative to each other, and to directly correlate these data with met-allographic measurements from which the interfacial planes can be determined on the same specimen. The back-reflection Laue technique is the easiest way to determine the orientation of thick single crystals or large grains and the method can be combined with metallographic techniques to provide the necessary data, provided the reflections from each phase can be distinguished from one another. However, if the crystallites are small or of varying orientation or if one or both phases has a unit cell with less than the maximum symmetry, many overlapping and complex Laue patterns are recorded simultaneously and it becomes impractical if not impossible to interpret the photographs. All of these complexities were present in a unidirectionally so- lidified A1-CuA12 eutectic alloy1 for which a crystallographic analysis was desired. Consequently the method described here was developed since no known X-ray or electron diffraction technique had all of the following attributes which were required. 1) Method should yield data from which the crys-tallographic orientation of every crystallite or diffracting unit in the irradiated area can be determined. 2) Method should be adaptable to the study of small areas. Depending upon the degree of preferred orientation in the specimens, it should be possible to obtain reliable data in a reasonable length of time on irradiated areas as small as 1.0 or even 0.1 mm in diam. 3) Method should permit direct correlation of crystallographic data with microscopic orientation data pertaining to crystallite axes, habit, morphology, and growth directions as determined by optical microscopy. 4) method should be such that selected areas of large specimens can be easily studied. Trepanning of a small specimen (such as an electron microscope specimen) from larger specimens was undesirable since it would greatly increase the problem of correlating the crystallographic and microscopic directional data. Requirements 3 and 4 dictated that an X-ray back-reflection pinhole technique should be used on large samples, such as metallographic specimens which had previously been examined and analyzed for their microscopic characteristics. Similarly, requirement 2 could be satisfied by choosing a collimator of appropriately small diameter. Exposure times would not be excessive provided the detector were close enough to the specimen. Because of space limitations film was chosen in preference to a Geiger counter. Requirement 1 was fulfilled by using monochromatic radiation and providing enough additional degrees of freedom in specimen rotation to compensate for Bragg law restrictions on diffracted beams. DESCRIPTION OF APPARATUS The apparatus shown in Fig. 1 consists of a pin-hole collimator, (a), projecting through a rotatable circular film in a holder, (b), which records X-ray reflections in the back-reflection region. The specimen, (c), is mounted on the end of a shaft, (d), which is provided with an adjustment, (e), so that the specimen surface can be placed accurately on

Jan 1, 1962

By Hugh Steele, Brower Dellinger

U. S. mining trends for 1956 continued steadily U+ S. uphill, technique and equipment advanced with the pull, and exploration and development of once mined districts attracted more attention than new areas. Expansion of the Ambrosia Lake district in New Mexico more than doubled known uranium ore reserves, and production began from several of the large new ore discoveries. In Canada the up trend was more spectacular, especially in exploration and development. To combat increasing problems arising from high labor costs, taxes, low grade orebodies, and dwindling discoveries, manufacturers and mining companies have continued to introduce new techniques and new products-reamer bits for enlarging small holes drilled by jacklegs, whup d'whups for drift mucking, Cryderman machines and over-the-head small crawler-type machines for shaft mucking, the 20-ton TL 220 four-wheeled tractor trailer unit for underground haulage, inertia-type dust collectors, roof bolting in conjunction with chain link fencing for wall support, wooden roof bolting using compression support of ground for wall support, and new one-use carbide bits.

Jan 2, 1957

By Frank F. Aplan

In looking into the crystal-ball scene of minerals beneficiation for 1970 and beyond, an impartial observer becomes con- fused as to what has been done and what is possible in the way of improvements. The mining official must balance the burden which is being shouldered by the mineral industry for maintaining our environment in its pristine state on one hand, with the solid advancements made in technology and cost savings on the other hand. Then the official wonders if this is really the criterion for judging overall performance today. As a prospective engineer, Dave Bolles sees it this way: "Specialization has caused many engineers to subordinate everything to doing their job the cheapest and fastest way. In the future this won't be enough. The engineer in the mineral industry will be responsible not only for mining, concentrating and smelting, but also for the resultant wastes- the mine dumps, the tailing dams and the slag piles." (See Drift on page 63).

Jan 1, 1971

By R. F. Lynch, J. D. Wood

The Al-1.0 pct Mg alloy 565 7 was studied using optical microscopy and electron microprobe X-ray analysis. Constituent particles were found to exist inter-dendritically in the as-cast material in a region of precipitate free a -aluminum. Five phases besides a fine precipitate and a-Al were identified in the cast structure: Fel3, Fe2Al7, Mg2Al3, CUMgAl2, and Cu2FeAl7. Thermal treatments conducted for 100 hr at 1180°, 1130°, 1080°, 1030°, 980°, and 880° F revealed a general dissolution and spheroidization of the in-terdendritic constituent network observed in the cast structure. The principal constituents present in the thermally treated structures were FeAl3 and Fe2Al7 with the relative amount of Fe2A17 to FeAl3 increasing with a decrease in the treatment temperature. The phases Present in the wrought structure were identical to those observed after the thermal treatments, with the constituent particles strung out in the direction of rolling. ALLOY 5657 is a nonheat-treatable commercial purity Al-1.0 pct Mg alloy utilized extensively because of its bright finishing characteristics. This investigation was conducted to determine the constituents present in 5657 alloy, and to study the effect of extended thermal treatments on morphology. Numerous studies have been carried out to establish the equilibrium diagrams for various aluminum systems,1-3 with phase identification based on X-ray analysis, morphology, and the etching response of relatively large particles. Phragmen4 conducted a study of the phases in aluminum eutectic systems and compiled a "corrected" table of etching responses, drawing on his work plus that of Schrader,5 Keller and Wilcox,6 and Mondolfo.7 A review of the original work of Keller and Wilcox, and Mondolfo, which was concerned with the constituents found in commercial alloys, reveals that in numerous cases their etching responses differ from those reported by Phragmen and from each other. These inconsistencies may occur because a specific constituent will react to a given etch in a varying manner depending upon its size, the elements dissolved in the phase, the other constituents surrounding a phase, and the solute content of the matrix. Work with a commercial orientation was conducted on alloys 2024 and 3003 by Sperry8,9 and on alloy 3003 by Barker,10 where the relationship between the phase diagram and the nonequilibrium structure of an alloy was examined. Backerud11 investigated the A1-Fe binary system and found that at high cooling rates the equilibrium eutectic reaction forming a-A1 and FeA13 is replaced by another lower temperature eutectic reaction forming a-A1 and metastable FeAl6, a constituent first identified by Hollingsworth et al.12 Most of the above mentioned studies were conducted on materials having a significantly greater alloy content than 5657 alloy, where the relatively small size and sparse distribution of second phase particles hinders the process of identifying constituents. EXPERIMENTAL PROCEDURE Material with a composition as given in Table I was examined in the as-direct chill cast, hot rolled and cold rolled conditions, and after thermal treatment of the cast structure. Thermal treatments were terminated by a water quench. Microscopic examination was conducted under various lighting conditions following the application of standard etchants as specified in Table 11. A semi-quantitative electron microprobe X-ray analysis was conducted for Al, Mg, Fe, Cu, Si, Zn, and Ti. RESULTS AND DISCUSSION Microstructure of the As-Cast Material. Particles of second phase material were found to exist inter-dendritically, principally in regions of precipitate free a-Al, as illustrated in Fig. 1. Adjacent to the ingot edge was a region of inverse segregation, resulting in an increased amount of second phase material containing large sized particles which aided in phase identification. Phase Identification. Cast Structure. Five phases besides a-Al and a fine precipitate were identified using optical microscopy and electron microprobe X-ray analysis, as presented in Tables II and III, respectively. FeA13 and Fe2A17 are often found with Fe2A17 forming a sheath around the core of FeAl3, resulting from an incomplete peritectoid reaction. These phases have a nearly identical appearance under white light, although they are easily differentiated under crossed polarizers, as characteristically illustrated in Figs. 2(a) and 2(b), respectively. Microprobe analysis con-

Jan 1, 1970

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. ' The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By Frank J. Tolonen, Nicholas H. Manderfield, Paul Jasberg

EARLY in the study of the low grade iron formations of Michigan, wide variations in their structure and texture became evident. Because of these variations no simple method of concentration is possible, and those portions of the formations that can be exploited profitably under a given stage of metallurgical progress and existing economic conditions must be searched for carefully. Both structure and texture of the formations have an important bearing on their amenability to beneficiation. By structure is meant the banding planes of easy fracture, the porosity, and the degree of leaching. Texture, which includes grain sizes, shapes, and degree of interlocking, determines the amount of grinding necessary to liberate the mineral grains. Structure determines the liberation of portions richer in one mineral. Structure and texture may be termed the gross features of the formation

Jan 11, 1957

By D. E. Hartman, J. M. Roberts

A detailed study of the temperature dependence of the critical stress, TB . necessary to cause a damping loss of 1.41 x 10-6 g mm per mm3 in pre-strained magnesium single crystals has been carried out in the temperature range 82" to 320°K. Tb is found to be linearly related to the reciprocal of the ahsol~cte temperature in this temperature range. The temperature dependence of the anelastic limit, TA, defined as the stress necessary to form open unidirectional stress-cycle damping loops has been measured between 82" to 320°K. ta is found to be independent of temperature in this range. It is suggested that TA is determined by the stress necessary to activate Frank-Read dislocation NUMEROUS studies1-9 have been reported concerning the details of yielding and microstrain near and below the generally discussed macroscopic flow stress. The work of Kramer and coworkers10-13 is helpful in determining certain qualitative facts. concerning preyield phenomena. The absence of a stress-dependent delay time in annealed copper and aluminum single crystals between 83" and 298 suggests that the preyield mechanism is temperature-independent in this range. This is not sources. The temperature and stress dependence of the effective activation volume (Veff) has been measured in the damping-loop region in prestrained magnesium single crystals. The data suggests that Veff/kT is approximately constant, equal to 2 4.5 sq mm per g in the temperature range 130°to 298°K, and that Veff is almost independent of stress at stress levels greater than 10 g per sq mm. A restricted model is developed to predict the stress (rb) necessary to cause a small fixed damping loss as a function of temperature, effective activation volume, and dislocation density. Various possible dislocation mechanisms controlling TB are discussed. true for zinc, p brass, and iron crystals in the same temperature range, however, since the existence of a stress-dependent delay time suggests a thermally activated preyield mechanism in these materials.10-13 The work by Vreeland et a1.14 confirms the work by Liu et al.ll on delayed yielding in zinc single crystals. A stress-dependent delay time between 82" and 298°K was found12 in prestrained aluminum and copper crystals. These results suggest that the preyield phenomena may be different between prestrained and unstrained or annealed crystals. The temperature dependence of the yield point at 2 x 10-8 plastic strain found by Rosenfield and Averbach3 in annealed copper and aluminum is not in agreement with the delay-time data, unless possibly the delayed yielding experiment only de-

Jan 1, 1964

By Walter V. Knopp, Laurence Delisle

The aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixtufe of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals . normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion correspending to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected.that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low COSt material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, that is, finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemelltal powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: I. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. General Procedure The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1949

By A. A. Scheil, S. I. Hoyt

In technological studies on steel considerable emphasis has been placed on the identification of the foreign inclusions, testimony of which is adequately given in the metallographic literature covering methods for their identification. The outstanding accomplishment in this field is the scheme devised by Campbell, Comstock and Wohrman for identifying various oxides, sulfides, silicates and other constituents by systematic etching tests and microscopic examination.' The time involved in carrying out this procedure has led to attempts to secure quicker methods, or at least to shorten the time required to secure essential information. An example of this is the use of dark field illuminatin,2 but when this was tried out by the authors it was found that cavities and pits on the polished surface appeared bright on a dark field and could not be distinguished from small glassy inclusions. Still another means is the Leitz Ultropak, an instrument equipped with optical units for the illumination of the specimen by reflected light to secure an effect similar to dark field illumination. The structures are made visible in exceedingly sharp details by utilizing the inherent properties of the samples, such as refractive index, absorption coefficients and reflection powers. We have had no experience with the Ultropak, but a recent paper by Benedicks and Löfquist3 describes methods for determining the refractive index of (Fe, Mn) O and MnS by the use of this equipment. Presumably this method would be subject to about the same limitations as dark field illumination, though the, feature added by Benedicks and Löfquist appears to offer great promise in inclusion identification.

Jan 1, 1935

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, .however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort. Nature of Deposit During the periods when Searles Basin was flooded, the waters that passed through Indian Wells Valley spread out to form a broad, shallow lake providing, in effect, a settling basin for suspended sediment. The drainage into the deeper and more isolated Searles Basin thus was clarified to a great degree before concentration began. Today, the elevation of the dry surface of Searles Lake is 1618 ft, and the salt deposit measures 5x7 miles. At the eastern and northeastern margins of the main playa zone and just at the foot of the alluvial slope of sand and coarser wash from the Slate Range mountains, a rim of crusted salts rises a few feet above the level of the flat. The deposit is a saline efflorescence composed of salts that were presumably brought up with rising ground waters to be deposited at the surface by solar evaporation. This deposit consists chiefly of trona, and it is after this Trona Reef that the town Trona was named. Strip mining operations have been conducted in the past at infrequent intervals for the recovery of crude trona salts. The main focal point of interest in Searles Lake from a commercial standpoint is the main salt body located almost centrally in the basin. The exposed portion of this porous saline deposit covers approximately 12 sq miles and averages 71 ft deep. Its interstitial voids, which constitute 50 pct of the total volume, are permeated with a brine, which is in equilibrium with the soluble salt deposits. The brine is the raw material for the operations of the American Potash and Chemical Corp. plant at Trona, shown in Fig. 1. The soluble salt deposits are of interest for their potential values in future technologic development. The brine, which is stratified according to slight differences in density, stands usually within 6 in. of the surface of this exposed, firm, salt body. The surface is usually dry and will support the weight of heavy mobile units and drilling equipment. Occasionally, however, surface waters from the higher watersheds encroach upon the main salt body during infrequent periods of precipitation on the surrounding mountains. This water dissolves surface salt, becomes a dilute brine, and has been observed to stand as high as 18 in. above the salt surface when undisturbed. Windstorms will shift the water back and forth across the lake surface. The exposed salt body is surrounded by additional submerged areas of commercial soluble salt deposits covering some 20 sq miles, hidden from view by marginal playa mud. These vary in depth up to as much as 30 ft. Thus, the outline of exposed and submerged salt deposits of commercial value is estimated to cover a total area of 32 sq miles, which is roughly circular but slightly elongated from northwest to southeast. It has been estimated that each square mile contains about 100 million tons% f alkali salts. The results of drill borings in the past 15 years have brought to light the interesting fact that the main salt body lies superimposed on an impervious mud deposit from 10 to 15 ft thick containing relatively little soluble salt. Under this deposit lies a second soluble salt body 35 ft deep. The lower salt body is interspersed with numerous insoluble mud lenses and its composition is considerably different from that of the primary, or main salt deposit. Recent drill borings have not penetrated beyond 300 ft. They have, however, revealed that underlying the lower salt body, the mud sediments carry deposited minerals of trona, nahcolite, mirabilite and much less soluble carbonates or sulphates of calcium and/ or magnesium. This structure is shown in Fig. 2. Current Lake Survey Program Several hundred holes have been drilled in the deposit. However, to carry out a thorough and carefully correlated study of the composition of the soluble salts and other minerals in the dry lake basin, a drilling program was inaugurated recently and is now nearing completion. In this survey, pattern drill holes are sunk at regular lh-mile intervals to a depth of approximately 150 ft. Drilling equipment consists of a No. 51 C. P.

Jan 1, 1952