Search Documents

By S. C. Jones, J. A. Davis

This paper describes displacement mechanisms of micel-lur solution slugs, displuced by a thickened water "mobility buffer", in a glass micromodel and in consolidated Berea sandstone cores. Colored motion pictures, taken through a microscope, recorded interactions on a pore-to-pore bash in the micromodel. Production and differential pressure data from consolidated cores previously waterflooded to residua1 oil saturation revealed displacement mechani.sm.s macroscopically. Oil is displaced miscibly, while interstitia1 water is displaced immiscibly by the injected micellar. solution slug. Part of this water is dispersed and carried near the lead ing edge of the .slug, and some may remain as a residual saturation. Thickened water displaces any residual water. It also emulsifies with the. slug material, thereby displacing it. The displacement sequence forms banks of oil and water with relatively constant fractional flows, saturations, and mobilities. The mobility of oil and water flowing ahead of the .slug defines .slug viscosity required for stable displacement. Equations are presented that describe. several aspecis of the displacement flow behavior: oil breakthrough, oil cut during production of the stabilized bank, breakthrough of banked water and the resulting decreased fractional flow of oil, fluid mobilities, etc. Breakthroughs, calculated from the equations, are compared with experimental data. Slugs of micellar sollution, ranging from 1 to 5 percent PV, produced unusually high oil recoveries (up to 100 percent) in previously waterflooded consolidated cores. Investigation of the effect of mobility buffer size on oil recovery indicated that recovery is reduced in 3-in. X 4-ft cores for mobility buffer sizes .smaller than 50 percent of the pore volume. Introduction A new oil recovery process,* conceived in 1962, utilizes a slug of micellar solution' that has sufficient viscosity to avoid an unfavorable mobility ratio with respect to the oil and water it displaces. These micellar solutions are composed of hydrocarbons, water, and surfactants, and may contain electrolytes and co-surfactants. The micellar solution is displaced by a "mobility buffer". The mobility buffer is a bank of reduced-mobility fluid, preferably an aqueous polymer solution. The entire system is displaced by unthickened water. This paper describes some of the microscopic and macroscopic displacement mechanisms observed during laboratory development of the fluids for a potential field test. Microscopic phenomena were observed photographically in a specially constructed glass flow model and macroscopic data were taken from constant rate, tertiary displacements conducted in Berea sandstone cores. Qualitative Description of Micellar Solution Flooding This section qualitatively describes displacement mechanisms that occur when a slug of micellar solution is injected into a previously waterflooded core. The slug completely removes oil from the portion of core it contacts, and banks oil in the process. The oil saturation in this bank and the flowing WOR reach definite, fixed values that are determined by water and oil mobilities and slug characteristics. This zone of constant WOR and oil saturation will be called "stabilized oil bank" in the following discussion. When this stabilized bank reaches the outlet end of the core, the oil cut jumps from zero to a constant value equal to the fractional flow of oil. Saline water has little or no solubility in the slug. Because of this. the slug displaces in-place brine immiscibly. During slug injection, most of the brine is displaced ahead of the slug, some is carried along in the leading portion of the slug, and part of the brine may become immobile. The immobile, residual brine is later miscibly displaced by thickened water. Displacement of all the oil and only part of the water during slug injection results in a higher fractional flow of oil ahead of the slug than occurs when all the water is displaced after injection of thickened water is begun. The slug spontaneously emulsifies fresh (low-salt content) water. By emulsification, the slug can become infinitely diluted, and hence totally displaced, by thickened water. Fluid saturations in the core are shown schematically in Fig. 1. Parts A and B show conditions before and after the start of the thickened-water injection, respectively. Since thickened water displaces any residual brine by-

Jan 1, 1969

By John Mathews

IT is a great honor to be asked by. the Board of Directors of this Institute to deliver the Henry Marion Howe lecture. The invitation carries with it a great responsibility, which I accept with considerable hesitation and with a feeling of unworthiness to perform the duties expected of me in this hour devoted to the memory of the life, character, and work of the late Professor Howe. Many of you recall the scholarly address delivered here a year ago by Prof. Albert Sauveur, and the beautiful tribute he paid-to his friend and colleague of many years in the great work of changing the art of iron making into the science of iron. My association with Professor Howe, was of brief duration-only one year-and the relation was that of pupil to teacher. My feeling toward him in later years was always that of a humble disciple at the feet of a master. He attained his third academic degree in the year that I was born. I recall the pride I felt when, after entering the, steel industry, I received from him, from time to time, letters asking for information or, perchance, asking my opinion, and he was always most punctilious in acknowledging the source of such bits of information in his writings. It was also my good fortune to sit at the feet of another great teacher-Sir William Roberts-Austen, at the Royal School of Mines. I mention him because his name was used by Osmond in coining the word "austenite," which is the subject of this address, and Osmond's suggestion was heartily approved by Howe. These three international metallurgists were the best of friends and delighted to honor the achievements of one another. There are other reasons for mentioning Roberts-Austen at this time. It was an introduction from Howe that opened to me the door of his -laboratory as well as of his heart. It was while at Roberts-Austen's laboratory that I .worked side by side with William Campbell

Jan 4, 1925

Sykes, W. P.-Effect of Temperature, Deformation, Grain Size, and Rate of Loading on Mechanical Properties of Metals. Discussed by Zay Jeffries, W. H. Bassett, F. E. Carter 3 Evans, Geo. Watkin.-Alaskan Coal Fields. Discussed by P. N. Moore, H. H. Stoek, G. S. Rice, H. Emerson 4 Eavenson, Howard N.-Run-off and Mine Drainage. Discussed by J. R. Campbell, Andrew B. Crichton, J. B. Warriner, R. V. Norris, H. G. Moulton, H. B. Wright 7 Andrews, Allen, and Garcia, John A.-Skip Hoisting for Coal Mines. Discussed by R. V. Norris, Geo. S. Rice, H. N. Eavenson, E. A. Holbrook, Robert Obert, Andrews Allen, T. M. Chance 12 Rice, Geo. S.-Coal-pillar Drawing Methods in Europe. Discussed by Carl Scholz, D. Harrington; H. 1. Smith 16 Knapp, Arthur.-Modified Oil .well Depletion Curves. Discussed by Roswell H. Johnson 21 Alvey, Glenn H., and Alden W. Foster.-Barrel-day Values. Discussed by Roswell H. Johnson 22 Matteson, W. G.-Secondary Intrusive Origin of Gulf Coastal Plain Salt Domes. Discussed by Eugene Coste, E. W. Shaw, Joseph E. Pogue, F. G. Clapp, E. DeGoIyer, W. G. Matteson, H. W. Hixon, R. Van A. Mills 23 Reger, David B,-Carbon Ratio of Coals in West Virginia Oil Fields. Discussed by J. T. Singewald, Jr 33

Jan 5, 1921

By C. O. Burgess, W. D. Forgeng

DESPITE the increasing interest in and the technical importance of iron-chromium-manganese alloys, very little published information is available regarding their constitution. F. M. Becket's paper1 in 1930 represents the first correlated effort in the field of these alloys. The paper served particularly to draw attention to the commercial possibilities of iron-rich alloys containing chromium and manganese in balanced proportions. The duplex structure of alloys within the commercial range was briefly discussed, but exposition of their structural constitution was necessarily limited because the physical properties and corrosion resistance of the alloys were the main subjects of the paper. Both prior to and following the publication of F. M. Becket's paper, and at his instigation, an extensive investigation of the constitution of iron-chromium-manganese alloys of commercial purity was in progress at the Union Carbide and Carbon Research Laboratories, Inc. The present paper is based on the results of that investigation. In the last few years, investigations covering various portions of this alloy system have also been made in Europe. W. Koester briefly mentioned the effect of annealing on chromium-manganese steel2 and later3 constructed approximate sections of the iron-chromium-manganese equilibrium diagram. M. Schmidt and H. Legat14 even more recently studied this system, and their article and conclusions are of interest as representing an entirely independent study of a number of iron-chromium-manganese alloys. Koester's sections are shown in Fig. 1. The figures summarize the effect of manganese additions to iron alloys containing 5, 10, 15 and 20 per cent Cr as well as the effect of increasing chromium content on iron alloys containing 3, 8, 20 and 30 per cent Mn. These diagrams, within their composition limits, substantiated in some measure the results of our investigation. However, in our work some differences as regards the position of the mixed alpha-gamma fields were found as compared to Koester's work, and we were able to detect the presence of

Jan 1, 1938

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

By Guy Bjorge

IN recent years the Homestake mine has been served by three shafts, the B. &. M., the B. & M. No; 2 and the Ellison, supplemented by an inside shaft, the Milliken, extending from the 2000-ft. level to the 3200-ft. level. In 1932, when a new operating shaft was under consideration, the bottom of the mine was at the 3200-ft. level. The B: & M. and the B. & M. No. 2 shafts were down to the 1550-ft. level and the Ellison was being deepened from the 2600 to the 3200-ft. level. All ore was hoisted at the B. & M. and-Ellison shafts. Levels below the 2600 level, which were under development only, were served by the Milliken shaft. Below the 1550-ft. level, the mine was served only by the Ellison shaft from the surface. Within a few years, when ore reserves above the 1550-ft. level would be depleted, operation would be limited to the Ellison shaft and the auxiliary underground shaft. The Ellison shaft alone was not adequate for hoisting the entire output from the deeper levels and also handling all men and supplies. Further-more, assurance of safety and uninterrupted operation required- two fully equipped shafts to the deeper levels. Therefore a new operating shaft was authorized in November, 1932, and was named for A. J. M. Ross, the mine superintendent.

Jan 1, 1935

By Zay Jeffries

TUNGSTEN has the highest melting point of all the known metals, namely 3350° C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely. brittle and fragile at room temperature, and when possessing a fibrous structure it maybe ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and. ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given.

Jan 6, 1918

By Arthur Forsyth

A SEARCH through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1.

Jan 1, 1940

By S. T. Wlodek

The scale md subscale reaction products were identified and their rates of formation were studied in air over the range 1600" to 2000°F (871 " to 1149°C) for periods of up to 400 hr and for hoth the solution-annealed and aged conditions. The effect of prior sltrface preparation on suhscale oxidation was also studied The general oxidation behavior of both Ni-Cr-Mo-Al-Ti type alloys was similar. A surface film of a, Al2O3, forms immediately on exposure Subsequent oxidation continued at a linear rate (QL = 55 * 5 kcal per mole) as colonies of Cr2O3 nucleated at the A12O3/gas interface Further oxidation proceeded at a paraholic rate zvhiclz could he fitted to two successive rate constants. During paraholic oxidation, and depending on temperature, the scale consisted of Cr2O3, NiCr2O4 , and TiO2 with traces of NiO. In the case of Rene 41, the activation energy of both paraholic processes was 66 * 3 kcal per mole suggesting that diffusion of cations tlzrozrgh Cr2O3 was the rate -determining process. An unusual decrease in the oxidation of Udimet 700 at 1900°F where a spinel of Ni(A1,Crh0, zuas the predominant reaction product prevented the accurate assignment of activation energies for this composition. In both alloys internal oxidation of Al2O3 commenced shortly after parabolic scaling was observed. Prolonged exposure prod7tced intemal oxidation of TiN, and in Udimet 700 a complex Mo-Ni nitride was also found. At 1900oF, the subscale reactions in Udimet 700 undergo an inversion which parallels the decrease in surface oxidation; internal oxidation ceases hut is replaced by the formation of "spherodized" 3.' colonies. Surface-preparation techniqtles which introduce appreciable working, such as coarse surface grinding or grit blasting. increase the amount of alloy depletion and internal oxidation in Reni 41. The reverse is true of Udimet 700 for which electropolished or mechanically polished specimens show much more subscale oxidation than strongly worked stirfaces. The strongest commercial nickel-base alloys presently available are generic to the Ni-Cr-Mo-A1-Ti base which exploits the precipitation of Ni3(A1,Ti) as the main strengthening mechanism, while relying on solid-solution strengthening by molybdenum and chromium reinforced by the pre- cipitation of carbides to attain maximum properties. This study characterizes the oxidation behavior of Rene 41, the strongest alloy of the Ni-Cr-A1-Ti type commercially available in sheet form, and Udimet 700, whose higher aluminum and titanium content allows it to exhibit one of the more attractive combinations of high-temperature properties available in a wrought product. The scaling processes of complex, type nickel-base alloys have received relatively little attention. Malamand and vidal as well as Poulignier et al.2'3 have determined the composition gradients across the metal/oxide interface produced by high-temperature oxidation and considered the effect of surface perature, Limited weight-gain data has also been published by Fere 5 for alloys of this type and Radavich6 has identified the reaction products on Udimet 500 and Inco 702 after oxidation at 1832°F. Reference can, of course, be made to the excellent reviews of Kubaschewski and Hopkins7 or Ignatov and Shamgunova8 for a summary of the data available on the oxidation of binary and ternary alloy systems which are related to the more complex alloys considered here. EXPERIMENTAL The analyses of the different commercial heats studied are given in Table I. Using the experimental procedures previously established,9 continuous weight-gain data were obtained on both heats of Rene 41 sheet (A and B) and 150-mil-thick slices of cast Udimet 700. Subscale oxidation reactions were followed by static exposure of cylindrical specimens obtained from swaged Rene 41 (Heat C) and Udimet 700 (Heats E and F). In brief, continuous weight-gain tests were performed on specimens with a surface area of 10 to 12 sq cm. These were abraded through 600 grit Sic paper, electropolished to 2p rms in an electrolyte of 10 pct H2So4 in ethanol, and lightly etched in 10 pct HCl in ethanol before final washing and rinsing in ethanol. All continuous weight-gain data were obtained in dried (-70°F dew point) flowing (1 liter per min) air to an accuracy of +0.1 mg. Subscale oxidation processes were followed by the metallographic examination of 0.5-in-diam by 1.0-in.-long specimens. After an initial center-less grinding, various additional surface treatments were employed to determine the effect of surface preparation on subscale oxidation processes. Before exposure in zirconia crucibles, all samples were lightly etched in 10 pct HCl-ethanol, washed in ethanol, and dried. The depth of internal oxidation was measured to ±0.00025 in. on unetched specimens mounted so as to provide a taper mag-

Jan 1, 1964

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS t ARE ASSOCIATES THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY THE FIGURES AT THE END OE THE ADDRESS INDICATE THE YEAR OE ELECTION HEAVY FACED T1 PE SIGNIFIES HONORARY MEMBERSHIP *ABADIE, EMILE R , Min Engr P 0 Box 83, Berkeley, Cal '76 *ABBE, CLEVELAND, JR, Geol Aid, U S Geological Survey, Washington, D C '00 *ABBOTT, AI ARTHUR, Cerro de Pasco Mining CO , Cerro de Pasco, Peru, So America '95 *ABBOTT, ARTHUR V , Electrical Engr , Westinghouse, Church, Kerr & Co , 8 Bridge St, New York, N Y '82 *ABBOTT, CLARENCE E, Chief Min Engr, Care Fayal Mine, Eveleth, Minn '04 *ABBOTT, JAMES W , Min Engr , Special Agent, Rocky Mountain and Pa¬cific Coast Division, U S Dept of Agriculture, "Tile New Markham," Denver, Colo '94

Jan 1, 1910

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;' it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.' Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

By A. F. Giamei, E. J. Freise

A discussion of the various factors affecting the accuracy of volume fraction determination by the direct comparison X-ray diffraction method is presented. To minimize errors introduced by nonrandomization effects such as preferred orientation and large grain size, as well as errors introduced by statistical effects, an iterative mathematical analysis is introduced. This analysis is applied to all observable diffractio~ spectra from a given specimen by means of computer techniques and is statistically superior to the standard direct comparison technique which utilizes only one or tm sets of intensity spectra. The computer program also presents a graphical interpretation of- the results which enables the investigator to visualize and readily assess the scatter in volume fraction estimates caused by deviations from randomness. Finally, the iterative analysis is applied to experimental data collected from a series of plain carbon steels in both the as-received and spheroidized conditions to determine the volume fraction of cemen-tite present in each case. The results show markedly good agreement with chemical analyses for all spheroidized specimens. In theory, quantitative X-ray diffraction is a power-ful analytical technique for precise determination of the volume fractions of various phases present in a multiphase poly crystalline aggregate. There are two generally used methods; both utilize the fact that the intensity of a diffraction line of a particular phase is a function of volume fraction of that phase present in the aggregate. The more common method is the so-called internal standard technique where a known amount of standard substance is mixed with the aggregate containing the unknown. The resulting ratio of the intensity of a particular diffraction line of the unknown to the intensity of a diffraction line from the standard is used to find the weight fraction of unknown material by reference to the intensity data obtained from a previously prepared set of standards containing the same amount of standard material. The details of this technique are outlined in standard works on X-ray diffraction.' The disadvantages of the technique are that it requires the use of powder specimens and that the powder mixture must be homogeneous near the surface to the maximum effective beam depth. The alternative technique is the direct comparison method in which the ratio of the intensity of a diffraction line of a phase in the aggregate to the intensity of a second-phase diffraction line yields the ratio of the volume fractions of each phase present. This method has been applied most extensively to the determination of the percentage of retained austenite in martensitic steels and to determining the amounts of hcp and fcc allotropic modifications in pure cobalt5 and the amounts of hexagonal and rhombohedra1 modifications in graphite.8 This method is applicable to bulk as well as powder aggregates and is the technique which will be considered in the following text. It is the purpose of the present communication to show that by combining the results of X-ray diffrac-tometry with the use of high-speed digital computers the results of the direct comparison quantitative X-ray analysis technique can be optimized by using all of the data available on a diffraction pattern. THEORETICAL DISCUSSION In optimizing any quantitative X-ray diffraction experiment, the problem of accuracy vs time to collect and analyze the experimental data arises. For any method to be practical, it is required that both experimental and analytical procedures are reasonably short. In most of the previous work performed by the direct comparison method, intensity data from only one or two sets of peaks were used to calculate the volume fraction of phases present in the aggregate. Consequently, rather long-time experimental measurements are required to assure that the intensity data are sufficiently accurate to justify the use of one or two sets of data. By using computer techniques to analyze the experimental data it becomes feasible to use all of the available data on a diffraction pattern. By so doing, the time spent in measuring any one diffraction maxima can be appreciably reduced. Although this results in poor counting statistics for any one maxima, the number of data points available for analysis is greatly increased. Based on the above discussion, it will be assumed that a continuous scanning counter-diffractometer technique will be used to collect intensity data from a two-phase mixture. The integrated intensity of the ith diffraction line from the a phase in the aggregate is given by:'" where is the volume fraction of the a phase, The various quantities in Eq. [la] are angular independent while those in [lb] depend on the hkl spectrum of a particular phase. The meaning of the individual quantities in Eqs. [la] and [lb] are given in Appendix 1. It is convenient at this point to outline briefly the factors which will affect the measured intensity of any one hkl spectrum. a) Extinction effects arise from two independent experimental conditions. Primary extinction arises from a high degree of crystal perfection and results in spectra having lower intensity than predicted by Eq. [I]. Any treatment, such as powdering, which reduces

Jan 1, 1968

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By Ernest F. Burchard

A Reconnaissance of the manganese- and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines, under instructions of the Secretary of the Interior, in the spring of 1918. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the island. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, quantity, and availability of the manganese- and chrome-ore deposits in Cuba. Accordingly, the work comprised examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to a determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. Wile it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Moreover, the necessity for paying particular attention to the ore deposits and the mines precluded the possibility of making more general studies of the geology of the region, and of making satisfactory collections of country rock and of fossils, and so for other details as to the geography and geology of Cuba the reader is referred to the report by Hayes, Vaughan, and Spencer.l Mr. Burch returned to the United States about 10 days in advance of the writer, who continued, in company with Sr. Montoulieu, investigations of reported deposits in Pinar del Rio, Matanzas, and Santa Clara Provinces. On his arrival in Washington, Mr. Burch submitted to the Director of the Bureau of Mines a summary of the results of the work to date. Later the writer published, as Press Bulietin 190. 380 of the U. S. Geological Survey, a statement concerning the chrome and man-

Jan 1, 1920

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By A. P. Watt

Foreword...............................................................323 Location of District..................................................... 324 Geology and Mining..................................................... 325 Topography and Climate................................................. 325 Lcad Production of the District...........................................325 Operating Companies in Southeast Missouri................................ 327 History of the District................................................... 329 Present Method of Treating the Ore....................................... 335 Character of Ore Treated...........................................338 Chemical Analyses............................................. 339 Description of Polished Specimens.................................340 The Concentration Problem of the District............................. 341 Handpicking at Mine La Motte....................................... 343 Crushing............................................................344 Roll Practice in the District.......................................... 346 Screening Practice................................................... 347 Jigging the Ore..................................................... 347 Bull Jigging.................................................... 348 Hancock-jig Practice............................................ 348 Classification of the Ores.............................................. 350 Table Treatment....:............................................... 352 Regrinding of Middling.............................................. 354 Description of Marathon Mill..................................... 358 Results of Preliminary Tests.....................................359 Rod Wear in the Marathon Mill.................................. 367 Steel Consumption.............................................. 368 Design of Marathon Mills.............. :......................... 368 Treatment of Table Middling........................................ 368 Slime Concentration................................................. 370 Methods Used in the Past.......................................370 Present Methods of Treatment................................... 371 Flotation of Slime.......................;........................ 371

Jan 1, 1918

By C. O. Fairchild

ONE of the fundamental principles of efficiency is the use of adequate and permanent records. The rapid increase in the manufacture and use of recording pryometers is a proof of the appreciation of efficiency principles on the part of the manufacturers engaged in the various technical industries. Where recording pyrometers are not employed in an industry in which temperature measurements are necessary, one will generally find that a printed form is used upon which is written, periodically, the temperatures measured by an indicating instrument. It is no serious condemnation of the workman to state that such records are often "doctored," but it is rather a reflection upon the executive who puts such temptation in the way of a workman. One of the well-known "tricks of the trade" is to "force." a furnace so that it will be at the proper temperature during the periodic trips of the foreman or other official. Indicating instruments and recorders may be used together to great advantage. The recorder furnishes .a printed record and a check upon the operator of the furnace, and a record of value in correlating properties of the finished product with the heat treatment. The indicator should be of assistance to the operator in controlling the furnace or oven. Modern practice requires a temperature-recording instrument that is as simple as possible, rugged, reliable, and sufficiently accurate. Of these qualifications reliability is paramount, particularly in cases where the recorder is used for controlling the temperature automatically. By a reliable instrument is meant one that will run continuously with little attention and with a consistent degree of accuracy. That is, if it is in error by 5 per cent. one day, it must be in error by a like amount on any other clay, and not by 2 per cent. or 10 per cent. The earlier forms of recorders were complex and delicate, or mechanically unsatisfactory and inaccurate, and required considerable attention to keep them in operation. Within the past few years, however, the development in the manufacture of temperature recording devices has been highly satisfactory and many excellent instruments are now available. .

Jan 9, 1919

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05

Jan 1, 1910

The term "timbered stope" is here meant to denote stopes in which timbering is the predominant feature of the mining method. Stopes with stull sets, as in the Hecla mine, are types of timbered stopes; these types are probably the best-known. Timbering stopes by means of square sets is not as common as formerly, as the system is not often necessary, yet there are good examples and large tonnages are being mined by the method. The square set may be utilized in ordinary overhand stopes if the orebody is suitable. At some mines, square sets have been abandoned in favor of top-slicing; and at others, the square set has superseded horizontal cut and backfilling. A drift, either in the wall or orebody, is necessary before opening the sill floor. In wide deposits, there may be a grillage of drifts and crosscuts, and at least one raise to the level above is needed in each stope for ventilation and handling timbers and filling. The square sets are filled with waste rock from the hanging wall, sorted from the ore, from development work, or from the level above. As a rule, little timber is recovered. The examples include the Butte district, Mother Lode of California, Bunker Hill & Sullivan, Hecla, and Morning mines.

Jan 1, 1925

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have dealt with the methods of separating silver from copper. There now remains the portion which treats of solidified juices ; and whereas they might be considered as alien to things metallic, nevertheless, the reasons why they should not be separated from it I have explained in the second book. Solidified juices are either prepared from waters in which nature or art has infused them, or they are produced from the liquid juices themselves, or from stony minerals. Sagacious people, at first observing the waters of some lakes to be naturally full of juices which thickened on being dried up by the heat of the sun and thus became solidified juices, drew such waters into other places, or diverted them into low-lying places adjoining hills, so that the heat of the sun should likewise cause them to condense. Subsequently, because they observed that in this wise the solidified juices could be made only in summer, and then not in all countries, but only in hot and temperate regions in which it seldom rains in summer, they boiled them in vessels over a fire until they began to thicken. In this manner, at all times of the year, in all regions, even the coldest, solidified juices could be obtained from solutions of such juices, whether made by nature or by art. Afterward, when they saw juices drip from some roasted stones, they cooked these in pots in order to obtain solidified juices in this wise also. It is worth the trouble to learn the pro- portions and the methods by which these are made. I will therefore began with salt, which is made from water either salty by nature, or by the labour of man, or else from a solution of salt, or from lye, likewise salty. Water which is salty by nature, is condensed and converted into salt in salt-pits by the heat of the sun, or else by the heat of a fire in pans or pts or trenches. That which is made salty by art, is also condensed by fire and changed into salt. There should be as many salt-pits dug as the circumstance of the place permits, but there should not be more made than can be used, although we ought to make as much salt as we can sell. The depth of salt-pits should be moderate, and the bottom should be level, so that all the water is evaporated from the salt by the heat of the sun. The salt-pits should first be encrusted with salt, so that they may not suck up the water. The method of pouring or leading sea-water into salt-pits is very old, and is still in use in many places. The method is not less old, but less common, to pour well-water into salt-pits, as was done in Babylon, for which Pliny is the authority, and in Cappadocia, where they used not only well-water, but also spring-water. In all hot countries salt-water and lake-water are conducted, poured or carried into salt-pits, and, being dried by the heat of the sun, are converted into

Jan 1, 1950