Search Documents

By H. Conrad

The strain hardening associated with the creep of magnesium single crystals at room temperatu.Je was investigated by shear tests in which the direction of stressing was reversed a number of times after creep in a <100> direction. The strain hardening was strongly anisotropic; the largest amount occurring in the direction of flow and the least 180 deg to this. The time law for creep changed from a parabolic type to logarithmic for the first and subsequent reversals of stress. For a given stress the creep strain decreased significantly for the first and second reversals and then only slightly for subsequent reversals. The logarithmic creep constant a changed in a similar manner. A linear relationship was observed between the creep strain for a given reversal and the stress. The slope for the third reversal yielded a strain hardening coefficient 12 to 16 times greater than that observed for unidirectional flow. Al-though no recovery was observed upon resting at room temperature, the hardening resulting from stress reversals could be completely removed by heating to 450" C. PREVIOUS work1.&apos; indicated that the creep rate of magnesium single crystals tested in the temperature range of 78" to 364°K decreased with time. This was attributed to an increase in internal stress resulting from an accumulation of dislocations at internal obstacles. The object of the present investigation was to further evaluate the nature of this hardening by conducting tests in which the direction of stressing is changed after previous creep in shear in a given slip direction. Previous to 1950 three investigations indicated that a Bauschinger effect3 occurred for single crystals as well as polycrystals brass in tension compression,

Jan 1, 1960

By W. A. Krivsky, R. Schuhmann

Jan 1, 1962

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt&apos;s recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By N. R. Morrow, C. C. Harris

The experimental points which describe capillary pressure curves are determined at apparent equilibria which are observed after bydrodynamic flow has ceased. For most systems, the time required to obtain equalization of pressure throughout the discontinuous part of a phase is prohibitive. To permit experimental points to be described as equilibria, a model of capillary behavior is proposed where mass transfer is restricted to bulk fluid flow. Model capillary pressure curves follow if the path described by such points is independent of the rate at which the saturation was changed to attain a capillary pressure point. Aemodified suction potential technique is used to study cyclic relationships between capillary pressure and moisture content for a porous mass. The time taken to complete an experiment was greatly reduced by using small samples. INTRODUCTION Capillary retention of liquid by porous materials has been investigated in the fields of hydrology,l soil science,2 oil reservoir engineering,3 chemical engineering," soil mechanics,5 textiles: paper making: and building materials In studies of the immiscible displacement of one fluid by another within a porous bed, drainage columnsl and suction potential techniques2 have been used to obtain relationships between pressure deficiency and saturation (Fig. 1). Except where there is no hysteresis of contact angle and the solid is of simple geometry, such as a tube of uniform cross section, there is hysteresis in the relationship between capillary pressure and saturation.2 The relationship which has received most attention is displacement of fluid from an initially saturated bed (Fig. 1, Curve R2), the final condition being an irreducible minimum fluid saturation Swr. Imbibition (Fig. 1, Curve A), further desaturation (Fig. 1, Curve R), and intermediate scanning curves have been studied to a lesser but increasing extent.2 ,3,9-12 This paper first considers the nature of the experimental points tracing the capillary pressure curves with respect to the modes and rates of mass transfer which are operative during the course of measurement. There are clear indications that the experimental points which describe these curves are obtained at apparent equilibria which are observed when viscous fluid flow has ceased; and any further changes in the fluid distribution are the result of much slower mass transfer processes, such as diffusion. Unless stated otherwise, this discussion applies to a stable packing of equal, smooth, hydrophilic spheres supported by a suction plate5 with water as the wetting phase and air as the nonwetting phase. The discussion can also be applied, in many

Jan 1, 1966

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920&apos;s a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By J. H. Brophy, M. H. Kamdar, J. Wulff

A constitutional diagram for the Ta-W-Re alloy system is presented. Rhenium dissolves in the complete range of solid solutions between tungsten and tantalum up to 48 wt pct in tantalum &apos;to about 30 wt pct in tungsten. Intermediate x and u phases only are found. X-ray diffraction and fluorescence, metallography and melting-point measurements were employed. THE constitution diagram of ternary alloys of tungsten, tantalum, and rhenium for temperatures above 1000°C is reported in this paper. Alloys in this system rich in tantalum and tungsten are of interest for high-temperature applications, and those rich in rhenium for electronic applications. No ternary phase diagram appears to be available in the literature. The three-component binary diagrams have been previously established1-3 and the present ternary data are consistent with these. EXPERIMENTAL TECHNIQUES Commercially pure tantalum (99.7 pct), rhenium (99.99 pet), and tungsten (99.9 or 99.95 pct) powders were purchased from Fansteel Metallurgical Corp., Chase Brass and Copper Co., and Fansteel or Westinghouse Electric Corp., respectively. These powders were pressed without binder and arc-melted under helium. The preparatory and analytical techniques employed were identical to those used for the Ta-Re system investigation carried out in this laboratory.324 These included X-ray diffraction and metallographic phase identification, X-ray fluorescent and wet chemical analyses, solidus determinations and heat treatments in a resistance-heated tantalum-filament vacuum furnace. For microstructural examinations standard mechanical polishing techniques were used through diamond laps. Polished speciments of all compositions were etched by swabbing with 4 parts HI?, 4 parts HNO3, and 1 part H20. Since the microstruc-tures of alloys containing one or two phases closely resembled their counterparts in the respective binary systems, typical examples are omitted in this presentation. In all the alloys examined, it was possible to observe the number of phases present. Particularly when there were small amounts of one phase involved, it was possible to identify it only by a combined conclusion based on X-ray diffraction, position of an alloy in a composition series, and the phase rule. A total of 100 different alloy compositions was arc-melted and studied in the as-cast condition metallographically and by X-ray diffraction. Specimens of each of these compositions were heat-treated at 2680, 2530, and 2020°C for 1, 2, and 4 hr, respectively. Those which were treated at 2020 were given a preliminary homogenization treatment at 2500°C for 1 hr. Specimens of 25 alloys were heat-treated at 1200o C for 168 hr. Solidus temperature measurements were made by the detection of incipient melting in eighteen alloy compositions. The metallographic and X-ray diffraction results are summarized in Table I. Graphically, this information appears in the isothermal plots of Figs. 2 and 3. Within the accuracy of the experimental methods, two such plots are sufficient to locate these data, since the results for 1200°C were similar to 2020 and those at 2530 resembled 2680

Jan 1, 1962

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the 5 potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum < potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the 5 potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.&apos; Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as PH, reagent concentration, and floc size and density. Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

By K. E. Merklin, F. D. DeVaney

Students of the modern blast furnace seem unanimously agreed that they are observing a major revolution in practice. Rather than changing construction and operation of the furnaces, most of the great advances now under way deal with the raw materials feed. Prepared burdens have gained increasing significance during recent years. Sizing, concentration, and agglomeration have all become bywords to greater production and reduced operating costs. The remarkable results with test furnaces in which self-fluxing sinter makes up part or all of the ore charge foretell even greater improvements. Other investigators have reported many of these advances, and it is enough to predict here that more and more operators will turn to the use of self-fluxing sinter. This change in the operator&apos;s requirements comes at a time when one major section of the iron ore regions, the Mesabi, is finding it difficult to maintain, let alone improve, the tonnage and grade of its shipping product. To meet the new demands with respect to quality and structure, the iron ore producers of this area turned first to screening, crushing, and concentrating intermediate ores. More recently, declining higher-grade reserves have led to multimillion-dollar investments in plants to treat the low-grade magnetic taconites.1,2 To yield a suitable concentrate, the Minnesota magnetic taconites must be ground to about 80 pct through 325 mesh, too fine to be charged directly to the blast furnace or to make acceptable feed to the sinter strand. The pelletizing process was developed to meet the structure requirements laid down by the blast furnace operators. Taconite producers are succeeding in their efforts just when the attention of the blast furnace man is being drawn to the great advantages of self-fluxing sinter.3 The taconite operators are ready with an alternative. Why not produce sclf-flus ing pellets? At the Hibbing laboratory of Pickands Mather & Co., where much of the early work was done that led to Erie Mining&apos;s 7.5-million ton taconite plant at Hoyt Lakes, Minn., preliminary investigations have been made. Present Taconite Operations: Details of this work will be clarified by a brief review of agglomeration practice in commercial taconite plants. After the taconite has been ground to about 80 pct through 325 mesh to liberate the magnetite grains, the ore is concentrated on magnetic separators, thickened, and filtered to about 10 pct moisture. This structure and moisture fit in closely with the conditions required to produce good balls. It has been found with taconite concentrates that at least 60 pct of the feed to the balling drum must be —325 mesh to obtain good ball compaction within reasonable time. The filter cake moisture usually permits a slight water addition at the balling drum, and further balling control is obtained by adding about 12 Ib of bentonite and 1 1/2 lb of soda ash per dry short ton of concentrate. These additives, and occasionally small quantities of fine coal, are thoroughly mixed with the filter cake ahead of balling. The swelling property of bentonite improves the green and dry strength of the balls so they can be handled without breakage until they are fired. Soda ash is added for pH control to insure maximum performance of the bentonite, and coal is added for more heat in the firing process when required. The balls, normally 3/8 to l-in. diam, are brought to a temperature of 2350" to 2500°F in the indurating furnace. Heat for this process comes from three sources: 1) fuel burned in the combustion chamber, 2) oxidation of the magnetite concentrates to hematite, and 3) coal added to the balls. Pellet strength is developed by grain growth and bridging and, if enough slag-forming constituents are present, by slag bonding. Conversion to hematite is usually close to 100 pct in the fired pellets. Batch Test Procedures: Initial studies of self-fluxing pellets were made by producing balls on a batch basis under carefully controlled laboratory conditions. The l-in. balls, uniform in size, were fired in an oxidizing atmosphere in a standard laboratory muffle furnace. The firing procedure consisted of

Jan 1, 1961

By A. T. Miesch, L. B. Riley

Distribution of minor elements in sandstone-type uranium deposits of the Colorado Plateau is being studied by the USGS on behalf of the A EC. A primary objective has been to provide basic data which could be useful in geo-chemical exploration for new deposits. The basic statistical measures — similar to those used in sedimentary petrology—are described. The underlying principle is that the frequency distributions fit or approach the log-normal form. Since 1952 the U. S. Geological Survey on behalf of the U. S. Atomic Energy Commission has conducted a study of the distribution of minor elements in sands tone-type uranium deposits of the Colorado Plateau. A primary objective in this study has been to provide basic data which could be useful in geo-chemical exploration for new deposits. Among the basic data considered important are estimates of the abundance and habit of each element in the ore and in the host rocks. It has been found that a few basic statistical techniques, and variations of these techniques, are useful in this type of study. Some of the basic techniques have been used to advantage by researchers in geochemistry and in other fields of geology, especially sedimentary petrology; others have been used to only a limited extent. Among the latter is the linear correlation coefficient, which has proved useful in assessing the element associations in a particular rock type without analysing individual mineral separates. In computing the basic statistical measures a scale has been used which is, in some ways, similar to the phi ($) scale used by sedimentary petrol-ogists in grain-size studies.&apos; FREQUENCY DISTRIBUTIONS It has been recognized for some time that the results of analyses for a given minor element in a suite of samples of rocks or ores yield frequency distribution curves which are approximately normal when the curves are plotted on logarithmic or geometric scales. In other words, the analytical results give an approximate lognormal frequency distribution. A classical example is given by D. G. Krige2 in the study of the distribution of gold values from a mine on the Witwatersrand. Another example is shown in Fig. 1, the distribution of barium concentrations in samples of uranium ore from the Chinle formation. The geochemical data are analogous to grain-size data gathered by the sedimentary petrologist. Both types of data, after simple logarithmic transformations, may be treated by conventional statistical methods based on the normal distribution. This is not to say that other types of transformations may not serve equally well or better for particular element distributions.3 Spectrographers and other analysts are quite aware of the dependence of their precision on the concentration of the element present.4 For example, in the part per million range the variation may

Jan 1, 1961

By C. H. Wayman, D. W. Fuerstenau

The effect of bubble size and concentration of certain reagents on the terminal velocity, shape, path, and drag coefficients of single air bubbles in distilled water has been investigated. Bubbles of a certain size range rise considerably faster than Reynolds number-drag coefficient relationships predict, whereas a small amount of frothing agent reduces their terminal velocity. The rapid velocity at which bubbles rise in distilled water appears to result from slip at the boundary and from circulation within the bubbles. Surface-active agents retard bubble motion through prevention of both circulation and slip at the boundary. A surface tension concentration gradient helps maintain bubble sphericity. HE gas phase is one of the indispensible in-gredients in flotation operations. Flotation depends on the collision of an air bubble and a mineral particle in a pulp and their ability to remain in contact long enough for adherence to take place. Before it is possible to understand the mechanics of air bubble-mineral particle encounter, it is necessary to learn more about the nature of bubbles themselves before collision with a mineral particle has taken place. To date, little work has been done on air bubbles in flotation systems. In 1945 Fahren-wald&apos; presented a study of the role of frothers on air bubbles and on aeration in flotation, and recently Wark and Sutherland&apos; discussed the work of Rosenberg- in relation to flotation. The research reported in this present article was undertaken to investigate systematically the effect of bubble size and the concentration of certain reagents on the terminal velocity, shape, path, and drag coefficient of single bubbles in distilled water. Most of the work is concerned with the effect of a-terpineol on bubble motion in water, but studies were made with potassium chloride, potassium hydroxide, potassium ethyl xanthate, and potassium amyl xanthate. Experimental Method and Materials: To obtain free bubble rise and reduce wall and surface effects, the investigators used a tank of 5½x5½x30-in. internal dimensions, filled with water to within 4 % in. of the top.&apos; The tank was made of acrylic plastic so that the walls would have good optical properties. Distilled water, which was re-distilled in a block tin still and saturated with air before each test, was used in all the experiments. All solutions were made with reagent-grade chemicals. During each experiment the water was at room temperature, and during the course of an experiment the temperature did not fluctuate more than 0.5°C. Since the experiments were performed over a period of six months, the temperature varied between 25° and 27°C. The temperature at which each series of experiments was conducted is recorded with the data. The experimental apparatus is presented dia-grammatically in Fig. l. Individual air bubbles were generated from purified compressed air through a capillary of 0.003-cm internal diameter at a rate

Jan 1, 1959

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author&apos;s aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.&apos; It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961

By L. L. Seigle

Free energies, heats, and entropies of mixing of solid Fe-Au alloys have been measured by the galvanic cell method between 800° and 900°C. A positive deviation from Raoult&apos;s law and a large excess entropy of mixing were observed, both attributable to lattice distortion caused by the disparity in component atom sizes. Since the terminal solid solutortiontions are not regular, thermodynamic properties computed from the location of the mis-cibility gap do not agree well with measured quantities. The electromotive force data suggest some changes in the existing Fe-Au phase diagram. ALTHOUGH a considerable amount of information has been accumulated about the thermodynamic properties of metal solid solutions which exhibit negative deviation from Raoult&apos;s law, particularly those in which ordering occurs, relatively few experimental measurements have been made on solutions with positive deviation. This is due to the infrequency of broad homogeneous regions suitable for experimental measurement in solutions of this type, since any marked positive deviations from ideality lead to restricted solubility and the formation of miscibility gaps. Thermodynamic data reported in the literature for such systems have usually been calculated from the location of the miscibility gap boundaries under the assumption that the entropies of mixing are ideal, i.e., the terminal solutions are regular.&apos; One of the few binary systems with both positive deviation and a wide homogeneous range in the solid is the Ni-Au system. A recent investigation of solid Ni-Au alloys&apos; revealed that the entropies of mixing were much larger than ideal and consequently thermal data computed from the phase boundaries assuming regular solutions were seriously in error. Theoretical considerations put forward by Zener indicated that high entropy values should generally be associated with systems possessing a miscibility gap in the solid, when this is due to differences in the size of component atoms. These facts suggest that the regular solution assumption is a poor approximation for many solid solutions with positive deviation and that reliable thermodynamic data generally cannot be obtained by conventional methods from the location of miscibility gap boundaries. The Fe-Au system, Fig. 1, resembles the Ni-Au system in certain respects. The presence of a miscibility gap in the solid indicates a large positive deviation from ideality, but there is nevertheless an extensive single phase region suitable for experimental measurement. The following investigation of solid Fe-Au alloys was carried out in order to obtain additional data on the thermodynamic properties of metal solid solutions with positive deviation from Raoult&apos;s law and to further compare thermodynamic data computed from miscibility gap boundaries with those measured experimentally. Experimental Method The thermodynamic properties were derived from measurements of the potential developed between pure solid iron and Fe-Au alloys in a high temperature galvanic cell. The experimental apparatus and technique were the same as those used for the Ni-Au alloys and described in a previous report.&apos; Cell electrodes were 1/16 in. diam rods swaged from chill-cast ingots and annealed for one week at 850°C. The alloys were prepared by melting fine gold granules under argon with pure iron obtained from the National Research Co. The cell electrolyte was

Jan 1, 1957

By Thomas C. Wilder

Jan 1, 1965

By A. B. Parsons

Jan 1, 1971

By William Paxton Hewitt

In the Santa Eulalia mining district, Chihuahua, Mexico, the main mineral zone occurs in a gently warped dome with simple associated structures and contains orebodies distributed through a vertical range of over 900 m. The stratigraphy of 1945 m of geologic column is described and an abrupt shrinkage is documented in the volume of limestones immediately associated with large orebodies. Termed collapse, this shrinkage occurred during the course of mineralization. Contacts of limestone with igneous sills, and 366 m of fossiliferous limestone beds, particularly the main fossil bed, have been important localizers of ore-bodies. Up-dip gravitational controls may have been important. Fractures have exerted only local controls and over short distances. Thrust zones have displaced diabase sills and in turn have been intruded by upper members of a group of rhyolite porphyry sills. Mineralizers were related to the rhyolite porphyry, and ore has been introduced to the limestone where certain sills lie between the displaced segments of diabase and have been cut by north-south fissures. Speculations are raised that fields of unreleased strain may have influenced orebody locations; the district&apos;s zoning pattern may be a reflection of the filtering effects of large volumes of limestone; and that metal-rich brines mobilized by or incorporated within the invading porphyry might be the source of the mineralizers. PRODUCTION AND LOCATION The Santa Eulalia district has a production record approaching or exceeding 35 million tons of silver-lead-zinc ore from replacement bodies in limestone. In operation since the first years of the 17001s, production has been confined to two intensely mineralized areas separated by 2 km of barren limestone, the West Camp and the East Camp. Probably 50% has been mined since 1908, with over 90% from the West Camp. The West Camp, exploited through a vertical depth of 1945 m and now approaching exhaustion, is the subject of this paper. The district lies in the northern part of the Santa Eulalia Mountains in central Chihuahua in northern Mexico, 400 km south of El Paso, Texas, and 22 km southeast of Chihuahua City. Dominating the northern part of the range is the Cerro de Santa Eulalia, a broad rolling upland which contains the district&apos;s West and East Camps. The West Camp, on the west side of the range, centers around the village of Santo Domingo, which is 2 km northeast of the Real de Santa Eulalia (Fig. 1). REGIONAL GEOLOGY Thick-bedded middle Cretaceous limestones, probably Aurora, form the great bulk of the Cerro de Santa Eulalia. These beds, warped into a gentle dome, are severed on the west by a faultline scarp and truncated on the north by the Dolores Pass, a wind gap that

Jan 1, 1969

By K. G. Gorling, S. J. Wallden, N. B. Lindvall

It is the policy of The Metollurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editorial Director, Rixford A. Beals; Associate Editor, James J. Burke; Assistants, L. Capria and R. K. Larkin. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Choirmon; Dennis Carney, John Chipman, J. C. Fulton, J. H. Hollomon, H. tl. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and O. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division T. B. King. Cha~rmon; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman. F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham. Jr., Robert F. Hehe-mann, R. I. Jaffee, F. E. Jaumot, Jr., lrving R. Kramer, A. J. Leno, Horold Margolin, C. J. McHorgue, Russell A. Meussner, J. 6. Newkirk, H. W. Paxton, G. E. Pell~ssier, I. S. Servi, Alan U. Seybolt, A. J. Sholer, and Sack Wahsburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. O. Philbrook, and T. B. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephonne pennsylvania 6-9220.Petroleum Subscription Engineers$20 per year for non-AIME members in United States and North South and Central 6-9220.SubscriptionAmerica $25 toreign; $5 for AIME members. Single copies, $4.00, iinalo copies Southfpr;ign,andCentral $5 00. The AIME &apos;is $25not responsible for any statement made or opinion expressed in its publications Copyright 1958 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . Registered coble address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, ...and Chemical Abstracts . . . Application for second class mail privileges IS pending at New Yark, N. Y. Volume 212, Number 2.

Jan 1, 1959

By K. K. Landes

The north central and northeastern states supply over 50 pct of the chemical and metallurgical limestone produced annually in the United States, and Ontario is the leading source of this material in Canada. About three fourths of the chemical and metallurgical stone produced in this area comes from Michigan, Pennsylvania, Ohio, and Ontario. The specifications, physical and especially chemical, for chemical and metallurgical stone depend upon the end use, but in general the tolerance for impurities is so low as to rule out most limestones and dolomites. Both high calcium limestone and dolomite are used in the metallurgical and chemical industries. The principal metallurgical use is as a flux in iron ore blast furnaces and open hearth steel furnaces. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, in making calcium carbide, and in sugar factories. All deposits of high quality carbonate rock are definitely finite. Invariably and inevitably they diminish in either thickness or quality laterally so as to become unworkable as chemical and metallurgical stone. The size of these high quality lenses ranges from a few thousands of tons to hundreds of millions of tons. The best hunting for new supplies is in the geologic formations known to contain premium quality deposits. However, because of high transportation costs, carbonate rocks, to be workable, must be close to market, dollarwise. Definitions: Chemical stone is limestone or dolomite used as a raw material by the chemical industry. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, making calcium carbide, and in sugar factories. The specifications for chemical stone depend entirely upon the end product. Some uses require dolomite, some require high calcium limestone; in a few instances, notably in lime burning, either type of carbonate rock can be used as raw material. As a general rule, a fairly pure stone is necessary and for certain particular uses the tolerance for some elements such as sulfur, iron, and phosphorus may be extremely small. Metallurgical stone is used as a flux in furnace operations, especially in the blast furnace where iron ore is converted into pig iron and in the open hearth furnace where pig iron is made into steel. Either limestone or dolomite can be used in the blast furnace, but only high calcium stone is charged in the open hearth (except for rice-size dolomite used as a refractory). There are no rigid chemical specifications for blast furnace stone, but low silica, alumina, sulfur, and phosphorus are desirable. For open hearth use, in addition to low magnesia, a very low sulfur content is also specified by many furnace operators. For furnace use, fluxstone also must be sufficiently shatter resistant that it will remain in lump form during transport and charging into the furnace. Commercial stone is the term applied in the trade for crushed stone used for roadstone and in concrete aggregate. Many of our best chemical and metallurgical limestones are too soft to qualify in the Los Angeles abrasion test for use as commercial stone. However, some limestones, and a higher proportion of dolomites, do qualify for commercial stone and so can be sold to either market. Place Value: Even the highest grade limestone is still a bulk commodity with a relatively low value per ton. As a matter of fact there is very little difference in the average price per ton between high grade chemical and metallurgical stone and crushed limestone used commercially. Most high quality stone is produced in large operations with consequent low cost per ton whereas most commercial stone is produced in relatively small local quarries. As in the case of other bulk commodities most limestone buyers pay more for transporting the raw material than the cost of the stone at its source. For this reason steel furnaces and chemical plants

Jan 1, 1961

By Robert Bakish, William D. Robertson

AFTER more than fifty years of investigation and continuing failure in service, a satisfactory mechanism to explain stress corrosion cracking in homogeneous alloys is still lacking. The relative chemical activity of grain boundaries and adjacent grains, inferred from the boundary structure, has been used to explain intergranular cracking in a brass.&apos; This concept is probably correct as a general hypothesis, but it requires much more extensive development in order to explain satisfactorily the observed phenomena. For example, the specific function of the solute in an alloy must be considered, because intergranular failure does not occur in pure metals,&apos; which are structurally similar to homogeneous alloys. Also, in this connection, an inter crystalline fracture path in binary copper alloys can be changed to a transcrystalline path by relatively small ternary additions.&apos; The fracture path in ß brass is predominantly transcrystalline,&apos; in contrast with an inter crystalline path in a brass. Whether the two different fracture paths are the result of a difference in composition, crystal structure, or the state of long range order is unknown and cannot be determined with ß brass, because only the ordered state can be obtained at room temperature. The study of chemical activity at structural sites in the Cu-Zn system is restricted by the formation of opaque films in an ammonia environment in which stress corrosion cracking is generally observed. Furthermore, both components of the alloy are chemically active and the interpretation of observations is therefore relatively complicated. The Cu-Au system is a better choice for the purpose of studying structural factors. In particular, CuAu is very susceptible to cracking in ferric chloride and opaque films are not formed in this solution; it may be obtained in different states of long and short range order; and, finally, only copper is oxidized in dilute ferric chloride, which considerably simplifies the chemical problem. To provide information necessary for a more general explanation of stress corrosion cracking in homogeneous solid solutions, the following structural factors have been investigated in a Cu-Au alloy having a composition corresponding to Cu,Au: 1) the effect of long and short range order; 2) the structural sites from which copper is removed from the annealed and cold worked polycrystalline alloy; and 3) the effect of annealing time and temperature on structural reactions in the cold worked alloy. Experimental Procedure A Cu-Au alloy of nominal Cu3Au composition was cast from cathode copper and high purity gold and fabricated into sheet and wire. Chemical analysis for copper and gold indicated 48.92 wt pct Cu and 51.01 pct Au. Quantitative spectrographic analysis indicated 0.01 pct Ag, 0.002 pct Pd, 0.001 pct Pb, and 0.002 pct Fe, with traces of magnesium, silicon, and zinc. Presumably most of the remaining 0.055 pct corresponds to the limits of analytical precision. Heat treatments of wire and sheet were conducted in argon or vacuum. Wire specimens, 0.064 in. diam, were heated for 1 hr at 850 °C to establish a definite

Jan 1, 1957

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.&apos; In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors&apos; attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963