Search Documents

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 6 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and 6le this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. 11. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under- signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1942

Jan 1, 1888

Page The Cobaltchromium Binary System (paper by A. R. Elsea, A. B. \Yesterman, and G. K. Manning, Met. Tech. June, 1948, Mechanism of Precipitation in a Permanent Magnet Alloy (paper by A. H. Geisler and J. B. Newkirk, Met. Tech. Aug. 1948, Tp 2444)................................................................................................. 300 Some Effects of Applied Stresses on Precipitation Phenomena (~aper by W. L. Finlay and W. R. Hibbard, Jr., Met. Tech. Sept. 1948, Tp 2470)....................................................................................... 301 Diffusion of Carbon in Austenite with a Discontinuity in Composition (paper by L. S. Darken, Met. Tech. Sept. 1948, TP 2443) 304 An Electron Diffraction Study of Oxide Films Formed on Nickelchromium Alloys (paper by J. W. Hickman and E. A. Gul- bramen, Met. Tech. June 1948, Tp 2372)..................................................................... 305 An Electron Diffraction Study of Oxide Films Formed on Copper-nickel Alloys at Elevated Temperatures (paper by J. W. Hickman and E. A. Gulbransen, Met. Tech. June 1948, TP 2391)................................................ 307 Decarburization of Chrome Nickel Alloys by Their Surface Oxides in High Vacua and at Elevated Temperatures (paper by E. A. Gulbransen, W. S. Wysong, and K. Andrew, Met. Tech. Sept. 1948, TP 2438)................................ 307 Fractographic Study of Cast Molybdenum (paper by C. A. Zapffe, F. K. Landgraf and C. 0. Worden, Met. Tech. Aug. 1948, TP 2421)................................................................................................. 308 Effect of Composition on Grain Growth in Aluminum-magnesium Solid Solutions (paper by L. J. Demer and P. A. Beck. Met. Tech. June 1948, TP 2374)............................................................................. 309 Effect of a Dispersed Phase on Grain Growth in Al-Mn Alloys (paper by P. A. Beck, M. L. Holzworth and P. Sperry, Met. Tech. Sept. 1948, TP 2475)................................................................................. 310 Statistical Rate Theory of Metals—Mechanism of Flow and Application to Tensile Properties (paper by J. W. Fredrickson and H. Eyring, Met. Tech. Aug. 1948, TP 2423)............................................................... 315 Nucleation of Slip Bands (paper by J. G. Leschen, R. P. Carreker, and J. H. Hollomon, Met. Tech. Sept. 1948, TP 2476) and.. 318 Transient Plastic Deformation (paper by R. P. Carreker, J. G. Leschen, and J. D. Lubahn, Met. Tech. Sept. 1948, TP 2477).. 318 Plastic Deformation of Large Grained Copper Specimens (paper by W. R. Hibbard, Jr., Met. Tech. Sept. 1948, TP 2469). ... 323 Plastic Flow in Anisotropic Sheet Steel (paper by L. R. Jackson, K. F. Smith, and W. T. Lankford, Met. Tech. Aug. 1948, TP 2440)................................................................................................. 323 The Effect of Thermal-mechanical History on the Strain Hardening of Metals (paper by J. E. Dorn, A. Goldberg, and T. E. Tietz, Met. Tech. Sept. l948, TP 2445)....................................................................... 325 The Room and Elevated Temperature Properties of Some Sand Cast Magnesium-base Alloys Containing Zinc (paper by T. E. Leontis, Met. Tech. June 1948, TP 2371)..............................................................., 327 The Low Temperature Properties of Tin and Tin-lead Alloys (paper by H. S. Kalish and F. J. Dunkerley, Met. Tech. Sept. 1948, TP 2442)............................................................................................335 Thermal and Electrical Properties of Ductile Titanium (paper by E. S. Greiner and W. C. Ellis, Met. Tech. Sept. 1948, TP 2466).................................................................................................... 335 Property Changes during Aging (paper by A. H. Geisler, Met. Tech. Aug. 1948, TP 2436)............................... 337 Factors Affecting the Tensile Notch Sensitivity of Magnesium Alloy Extrusions (paper by I. Cornet, Met. Tech. Aug. 1948, TP 2419)................................................................................................. 338 Effect of Grain Size on Tensile Strength, Elongation and Endurance Limit of Deep Drawing Brass (paper by H. L. Walker and W. J. Craig, Met. Tech. Sept. 1948, TP 2478)............................................................. 339 A Copper-base Alloy Containing Iron as a High-strength, Highconductivity Wire Material (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Met. Tech. Aug. 1948, TP 2422).............................................. 340 A High Strength-High Conductivity Copper-silver Alloy Wire (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Mel. Tech. June 1948, TP 2366)...................................................................... 340 The Effect of Chronlium on the Ma Point (paper by J. B. Bassett and E. S. Rowland, Met. Tech. Aug. 1948, TP 2417.... 341 The Kappa Eutectoid Transformation in the Copper-silicon System (paper by W. R. Hibbard, Jr., G. H. Eichelman, Jr., and W. P. Saunders, Met. Tech. Sept. 1948, TP 2441).............................................................. 343 Stabilization of the Ausknite-martensite Transformation (paper by W. R. Harris, Jr. and M. Cohen, Met. Tech. Sept. 1948, TP 2446)................................................................................................ 344 Secondary Hardening of Tempered Martensitic Alloy Steel (paper by W. Crafts and J. L. Lamont. Mel. Tech. Sept. 194,8, TP 2439)................................................................................................. 345

Jan 1, 1950

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 147.

Jan 7, 1964

By AIME AIME

GENERAL COMMITTEES. SAN FRANCISCO:-ExECUTIVE, Hon. William C. Ralston, Chairman; RECEPTION, Prow. Samuel B. Christy, Chairman; SESSIONS, Frederic W. Bradley, Chairman; PRESS, H. Foster Bain, Chairman; FINANCE, Mark L. Requa, Chairman; EXCURSIONS AND ENTERTAINMENTS, Edward H. Benjamin, Chairman. Assisted by Harry P. Stow, C. W.Merrill, F. W. Griffin, Gelasio Caetani, Albert Burch, Newton Cleaveland, Corey C. Brayton and R. E. Cranston. Los ANGELES :-EXECUTIVE, Theo. B. Comstock, Chairman; R. W. Hadden, Secretary; H. R. Simpson, Treasurer. Institute Headquarters at Hotel St. Francis. The first and opening session, held Tuesday afternoon, Oct. 10,. in the Reception-Hall of the St. Francis, was called to order by State Senator William C. Ralston, Chairman of the Executive Committee, who in a few well-chosen words welcomed the visiting members and guests of the Institute to San Francisco. He said it was twelve years since the last meeting on the Pacific Coast and that it was here that the greatest feats. of mining had been accomplished in the history of the country. He told of the work that had been done on the continent and of the new methods introduced by the mining engineers for the betterment of the nation. He then introduced Capt. Robert W. Hunt, twice past President of the Institute, and present Acting President for the San Francisco meeting and the subsequent visit to Japan, who responded cordially to Mr. Ralston's welcoming address. By unanimous vote, the Secretary was instructed to send a telegram to President Charles Kirchhoff expressing regret for his absence, and hoping for a rapid improvement in the health of his mother. The following papers were presented in brief oral abstract by the authors: . * Electrolytic Refining at the U. S. Mint, San Francisco, Cal., by Edward B. Durham, San Francisco, Cal. The Parral Tank System of Agitating Slime-Pulp, by Bernard MacDonald, Guanajuato, Mexico. * The Newport Iron-Mine, Ironwood, Mich., by B. W. Vallat, Ironwood, Mich. (illustrated by lantern-slides). * Distributed in pamphlet worm.

Nov 1, 1911

By Oswald J. Heinrich

(with figures on plate V.) THE origin of spontaneous combustion in collieries is, of course, chiefly due to bad system in laying out the pits, unclean workings, insufficient ventilation, and neglect in damming off works after they are exhausted of the main coal. This is particularly indispensable in the Richmond field, because it is difficult and dangerous here, on account of the inferior roof, to remove the last vestiges of coal ; and we are compelled also to retain all the slates and bands, as far as possible, in the pit, to help fill up, although such material is liable to fire. This, however, can be prevented to a great extent, as men¬tioned below. I am satisfied that the only system of working this thick coal is by cross-cutting ( Querbau, ouvrage à travers) or working in benches, as practiced in France (Creusot, Rive de Gier, St. Etienne), in Sile¬sia (Königsgrube), which I have used as far as it is practicable in an old pit, almost torn to pieces by former workings. Modifications may, of course, be needed, even in the same pit, on account of irregu¬larities in the seam. I am also satisfied for economical reasons (on account of the heavy cost for timbering) that pits here ought to be worked upwards, even if it requires a longer period of time to win the coal, and a greater outlay of capital to commence with. The various saddle-shaped "troubles" making natural minor basins in the main basin aid in the execution of this plan. A pit worked once ought to be worked out clean, given up, and dammed off forever. If sections of proper height are assumed, according to the required amount of production for a certain period of time, they ought to be worked out and filled in as much as possible, dammed off, and ulti¬mately allowed to fill up with water, in order to protect the tipper works in future from fire in the gob below. This I consider indispen¬sable, because we may not be able profitably to fill in all the ground. To do so we have to use the waste of the mine, although it is liable to fire in time. In using this stuff, it ought to be surrounded by walls of rock not liable to take fire, laid firmly in clay, the gob being in the middle, and firmly covered and packed with clay on top. In

Jan 1, 1873

[ ]

Jan 1, 1938

In 1973, US Borax & Chemical Corp. began investing three days wages and about $20 in training materials in every new employee before having him report to his first job. The result? Accidents involving new employees in the past two years have dropped by more than half from the 1972 level. What made this success possible was safety training done with programmed instruction materials-which, incidentally, US Borax also uses for vocational training.

Jan 4, 1976

By R. Salter, C. K. Chase

Although Asarco's Silver Bell Unit, 40 miles west of Tucson, Ariz., is known primarily for copper production, molybdenite is also produced as a byproduct in the 8000 tpd flotation mill. The Silver Bell ore comes from two pits approximately two miles apart. Copper mineralization is essentially chalcocite resulting from two to three-fold secondary enrichment in a highly altered zone. A typical porphyry copper deposit, Silver Bell ore is of medium hardness. The ore consists of about one part molybdenum to 65 parts of copper. In the copper concentrate which is the starting point for separate molybdenum recovery, the ratio is also one part molybdenum to 65 of copper. Molybdenum mineralization is primary. Enrichment is not evident but it is notable that the molybdenite is more common in the more siliceous, harder rocks. The actual molybdenite occurs as diversely oriented flakes of fairly constant grain size, mostly in fractures associated with quartz veins. Most of the mineral appears unoxidized; secondary coatings on the molybdenite flakes are fortunately rare. In May 1962 a modified, improved version of the molybdenite circuit was put into operation.

Jan 7, 1964

THOSE NOT MARKED ARE MEMBERS; MARKED THUS ? ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR ASSOCIATES ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. ?AARONSON, ALFRED E Pres., Tuloma Oil Co., Unity Bldg., Tulsa, Okla. '18 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co. 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, LOUIS BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div. Jenkins, Ky. 115 ABBOTT, ROBERT R. Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Fujitagumi Taiwan Office, Taipeh Formosa, Japan. '14 ABEEL, GEORGE H., JR., Cons. Min. Engr., 4111 Lafayette Ave., St. Louis, Mo. '18 ABEY, HIROSHI, Min. & Met. Engr., Arakawa Mine, Mitsubishi Co., Senpoku-gun, Akitaken, Japan. '17 ||ABOUCHAR, S. S., Cia. de Minerales y Metales, S. A. Santa Eulalia Unit, Apt. 70, Chihuahua, Chih., Mexico. '17 ABRAHAMS, A. I 1391 Madison Ave., New York N. Y. '14 ?ACKER, E. O'C., Met., 128 East Washington Lane, Germatown Philadelphia, Pa. '86 ACKER, WILLIAM L., Diamond Drill Contractor... Mears Bldg., Scranton, Pa. '18 ?ACKERMAN, ERNEST R., Pres., Lawrence Portland Cement Co. Plainfield, anion Co.. N. J. '15

Jan 1, 1923

||Abad, Leopoldo F., Min Engr, Div of Mines, Bureau of Science Manila, P I '23 Abadilla, Quirico A, Geol, Lago Pet Corp Box 172, Maracaibo, Venezuela '20 ||Abbey, Robert Graham, The W W Sly Mfg Co Train Ave, Cleveland, Ohio '21 Abbott, A. N., Mines Supt, Mazapil Copper Co, Ltd Concepcion del Oro, Mexico '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn Coal, Iron & R R Co, 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky. '16 Abbott, Robert R., Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz. '23 Abeel, George H, Jr., Cons Min Engr 4612 West 17th St , Los Angeles, Cal '18 Abel, Albert E., Asst to Pres, Valley Mould & Iron Corp Sharpsville, Pa. '19 Abernathy, George Elmer, Prof of Geol & Min , Kansas State Teachers College, Pittsburg, Kans. '20 Abey, Hiroshi, Min & Met Engr, Min & Met Dept, The Higher Technical School, Osaka, Japan. '17 ||d'Ablaing, Philip R, Chem , Anaconda Copper Min Co Great Falls, Mont '25 Aborn, Robert H , Research Assoc., Mass Inst of Tech Cambridge, Mass '19 Abouchar, Sylvain Sley, Min. Engi & Geol , care of S H Sekaly, 13 Rue El Nimr, Cairo, Egypt '17

Jan 1, 1923

[A Aall, Christian H., M49 A Dir, Smelt & Ref, Am. Metal Climax, Inc., 1270 Ave. of the Americas, New York 20, N. Y. Aaroe, S. L., A54 A VP, W. S. Tyler Co. of Canada Ltd., P. O. Box 100, St. Catharines, Ont., Canada Abalos, Teodulo Q., J57 A Prod Frmn, Lepanto Cons. Mining Co., Lepanto, Mt. Province, Philippines Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abdullah, M. Y., J53 Dept. of Mines Res. Div., P. O. Box 1016 Tiger Lane,-Ipoh Peram, Malaya Abel, John F., Jr., J53 F Mine Engr, Thompson Creek Coal & Coke, Carbondale, Colo. Abell, Leo M., M31 B Const Supt, Phelps Dodge Corp., Morenci, Ariz. Abendroth, H. E., A57 Mangore Australia Pty. Ltd., 901 Hay St., Perth, W. Aust.,, Australia Abenius, Hakan V., M52 Falun, Sweden]

Jan 1, 1961

Jan 1, 1944

Jan 1, 1970

By John F. McElhiney, Hosseim Kazemi

This chapter is a review of fluid flow and mass trans- port in fractured rocks. The topics include: single-phase and multiple-phase flow theory, formation productivity or injectivity improvement by artificial fracturing, and mass transport associated with fracture acidizing. Possible extension and application of such ideas to in situ mining in fractured rocks are presented.

Jan 1, 1974

Jan 1, 1944

By Albert Sauveur

THE following experiments were conducted in order to study the influence of the rate of cooling through and below solidification on the dendritic structure (macrostructure) and microstructure of some hypoeutectoid steel. The steel selected was of commercial grade and had the following composition: C, 0.40 per cent.; Mn, 0.85; Si, 0.70; P, 0.099; S, 0.043. After melting in vacuum in an Arsem furnace, the various samples were allowed to solidify and to cool to room temperature as indicated in Fig. 1. Samples were thus obtained representing all possible combinations of slow and fast cooling through the various ranges of temperatures indicated, namely: (1), zone of solidification or primary crystallization, (2) zone of granulation, and (3) zone of secondary crystallization. The location of the different temperature zones in the iron-carbon equilibrium diagram is shown in Fig. 2. The authors adopted. Belaiew's notations. The designations of the various samples readily indicate their treatment, as will be apparent from Table 1.

Jan 1, 1930