Search Documents

By P. K. Frempong, S. D. Butt

"A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine.The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semivariogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates."

Jan 1, 2004

A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine. The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semi- variogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates.

Feb 1, 2004

By Patrick R. Stephenson

The current version of the JORC Code was issued in 2004 and since that date the Australian Securities Exchange, in collaboration with JORC, has issued a number of companies? updates to provide guidance on various reporting issues. An interim review will be undertaken during 2010 to meld these updates with the current 2004 Code. This will be followed by a full review during 2010/11 covering all aspects of the Code and focusing particular attention on: ? clauses / guidelines relating to Exploration Results1, exploration targets and the reporting of historical estimates; ? issues relating to the Public Report2, including definition, the requirements for Competent Person sign-off, level of disclosure and mandatory requirements; ? guidance on techniques to quantify resource / reserve estimation uncertainty; ? the level of study required to convert Mineral Resources to Ore Reserves, and disclosure of prices and economic factors; ? expansion of the requirements for reporting of marketable material for bulk commodities; ? the use of language and tone that anticipates new and emerging technologies and techniques for the qualitative and quantitative measurements of data; and ? linkages to valuation and the valuation code (The VALMIN Code). Although the Canadian and Australian reporting regimes for public statements on Exploration Results, Mineral Resources and Mineral (Ore) Reserves are similar in intent and coverage, they differ in detail, sometimes substantially. Canadian requirements are generally more wide-ranging and prescriptive than Australian requirements, including in the need in many situations to publicly lodge a Technical Report, a requirement that does not exist in Australia. Australian-listed companies seeking to list in Canada, and Competent Persons seeking to act as Qualified Persons in Canada, need to ensure that they are fully conversant with Canadian regulations and how they differ from those in Australia.

May 1, 2010

By Thomas R. Larson

"Many concentrators use re-circulating “plant” water for dilution in their flotation circuits. However, if crusher dust suppressants, ball mill grinding aids, or even agitator bearing grease are introduced into this water, and the water itself is not subject to cleaning steps, then sufficient quantities of these chemicals may appear in the flotation cells and begin to impact the flotation separation. A bench flotation procedure has been coupled with statistical analysis in order to estimate the impact of small quantities of non-flotation chemicals on flotation performance.INTRODUCTIONCleveland Cliffs produces iron oxide pellets for blast furnace feed, and is developing the capability to produce ferrous metallic products to supply a wider customer base. Cliffs manages five North American iron mines, including the Wabush mine sites in Labrador and Quebec. Based on various characteristics of the ore bodies, the flow sheets of the five mines are diverse. For example, Hibbing Taconite uses magnetic separation alone as their primary upgrading method, but Northshore and Empire use magnetic separation followed by flotation, and Tilden uses flotation alone. Last but not least, the Wabush concentrator upgrades primarily with gravity and electrostatic separation techniques.At Northshore, concentrate from the magnetic separator circuit is fed to a reverse flotation circuit. By design, the magnetic separators operate at the highest possible recovery of magnetite, as the separator tails are discarded, and relatively high silica content was acceptable to Northshore’s customers. As the steel-making industry moved toward lower and lower slag volumes, the silica content in the magnetic separator concentrate became a problem. The flotation step was added in the late 1980s in order to decrease the silica assay of the magnetic separator concentrate to meet the current customer requirements. In this setting, the flotation feed stream contains very little silica that occurs as liberated quartz particles. As the degree of liberation of the flotation feed stream is then a limiting factor for silica removal, the online grind control then was linked to flotation in the overall plant control system so that grind can be adjusted to achieve improved liberation if necessary for the flotation process."

Jan 1, 2002

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By A. Ouchi

This paper presents ground control best practices in weak rock environments including the "Unsupported" Weak Rock Updated Span Design Curve and awareness pertaining to the potentially detrimental effects of using resin grouted rebar in weak rock masses and the false sense of security that the use of resin grouted rebar may instill. Ground support is almost always used in weak rock environments, though the type of support used can vary widely. The development of the Weak Rock Updated Span Design Curve by the addition of 463 case histories of RMR76 values ranging from 25 to 60, has also been calibrated to four different support categories; Category A: Pattern Friction Sets, Category B: Pattern Friction Sets with Spot Bolting of Rebar, Category C: Pattern Friction Sets with Pattern Rebar Bolts and Category D: Cablebolting, Shotcrete, Spiling, Timber Sets or Underhand Cut and Fill. Design of underground man-entry type excavations in North America relies heavily upon empirical analysis. This design requires a higher Factor of Safety than other non-man entry type excavations. A comparison of the calculated ½ span failure Factor of Safety between all the categories is also presented.

May 1, 2009

By A. Griffiths, G. Vickell

"INTRODUCTIONA successful cyanide destruction process has to ensure environmental compliance at reasonable cost. That this is possible with hydrogen peroxide is shown by the fact that over twenty gold mines either already use H2O2 or intend to start using it within the next few months. About half of these mines are in Canada.This growth is remarkable, considering that the first treatment plant to use H2O2 for detoxifying cyanide was commissioned less than five years ago at Ok Tedi, in Papua New Guinea.Hydrogen peroxide is being applied to a wide range of situations, including:Treatment of CIP pulps; examples: Ok Tedi, PNG; Hope Brook, Nfld.Treatment of barren bleeds and filtrates; examples: Nickel Plate, B.C.; Puffy Lake, Man.Treatment of tailings pond discharge; examples: Detour Lake, Ont., Page Williams, Ont.Treatment of excess heap leach solution; examples: Hope Brook, Nfld; Gordex, NS.Treatment of barren heaps after heap leaching; examples: Alhambra, NV; Wharf Resources, S.D.Treatment of pond reclaim water to prevent either ""preg-robbing"" or depression of gold-bearing pyrite in a flotation step; example: Getchell, NV.Treatment of backfill to prevent possible groundwater contamination; example Hope Brook, Nfld.Treatment of tailings ponds to prevent bird kills; example: Paradise Peak, NV.""Emergency"" units to deal with unusual events such as freak storms or dam failures."

Jan 1, 1989

By Steve Hubbard, Brad Marchant, Rolando Cuadra

"Triton Mining Corporation acquired the rights to Mina El Limon in Nicaragua in 1993 by international bid. The bid included the gold operations at Limon and an exploration concession of approximately 4000 km2. Triton assumed control of operations and exploration in May 1994.The Limon mine is located in west-central Nicaragua, approximately 100 kilometers northwest of Managua. The climate is tropical, characterized by a wet season from May through October, and a dry season November through April. Gold at Limon is associated with both banded quartz and silicified breccia veins in Tertiary volcanic rocks, belonging to the lower Coyol Group. Mining is from two open pits and one mechanized underground operation. A second underground mine is currently under development for production during 1997.This paper describes the expansion of the milling facility at El Limon from a nominal capacity of 400 tonnes/day, producing approximately 20,000 ounces of gold annually, to the existing 900 tonne per day mill operation. Engineering of the new mill facility was initiated in September 1994 and construction was completed a year later."

Jan 1, 1997

By Rodolfo Espinosa Gómez

"Industrias Peñoles, S.A. de C.V. – Mining Division, has initiated in the last ten years, six Mining Operations (Bismark, Tizapa, Ciénega, La Herradura, Rey de Plata, and Francisco I. Madero) and it has expanded several of their existing Operations (Sabinas, Fresnillo, Tizapa, Ciénega) one or more times.This work aims to share the experiences learned on this growing process. Some of these lessons are: 1) Project leaders must have a leadership that fosters good communication and team work; and this leadership style must come from top management. 2) A good communication must exist between the personnel from Engineering, Construction, and Operation. Also, this good communication must come from top management. 3) Starting the project with a solid Engineering Study. 4) Do not misunderstand cost with cost/benefit; always look at the cost/benefit. 5) Selecting good Contractors and good Suppliers. 6) Good training before the project commissioning is essential to reduce the learning curve period, this is even more important in areas where local people do not have any background in mining activities. 7) Recognizing that any project has a learning curve and it must be reflected on the production budget. 8) Avoid an over optimistic Mine preparation time schedule.BACKGROUNDIndustrias Peñoles S.A. de C.V.The mission of Industrias Peñoles, S.A. de C.V. (Peñoles) is to add value to non-renewable natural resources in a sustainable manner. Peñoles seeks to build long-term shareholder value; provide their customers with the highest quality products and services; maintain productive longterm relationship with their suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which it operates, and preserve the environment.Peñoles was established on 1887. It is a Mining Group with integrated Mining, Smelting and Refining operations of non-ferrous metals, and also produces inorganic chemistry materials. Peñoles is the main World producer of refined silver, metal bismuth, and sodium sulphate; Latin American leader in the production of refined gold, lead, and zinc.The Mining Group is made-up of nine mining operations producing concentrates with high gold, silver, lead, zinc, and copper contents. It produced in 2002, 365,900 ounces of gold; 52.7 million ounces of silver; 86,820 tonnes of lead; 266,000 tonnes of zinc, 11,840 tonnes of copper; with a total values of 3,780.6 million of Mexican pesos (~ $ 378.0 million U.S. Dollars)."

Jan 1, 2004

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By Christoph Mueller

Mining operations today are characterized by a high degree of mechanization and single machine automation. However, their potential for cost cuttings and increase of productivity in the future is quite limited. Enabled by newest IT and networking technology, the operation of underground mines more and more can be seen from a process related point of view: Standardized Ethernet and Wireless LAN are the basis for a seamless and unified communication backbones providing an integrated infrastructure for data, telephony and video. All the components are available as off-the-shelf devices leading to an excellent cost efficiency. Basing on this standardized infrastructure, the equipment is able to become part of the infrastructure. To enable machines to be integrated smoothly into IT networks, the machine also has to have enhanced networking capabilities. This results in a new system architecture for the on board machine electronics separating real time control from IT and networking level functionality which can be implemented by a Machine Server. This machine server communicates with all kinds of above ground systems using mainly standardized formats like html or the IREDES standard. This information is made available mainly in 3D mine visualization tools. The paper explains this technology and shows implementations by two working examples.

May 1, 2006

By K. D. Hester

"1.0 INTRODUCTIONThe uranium industry started in Canada with the reopening of the gravity concentrator at Eldorado's Port Radium mine in the North West Territories in 1942. In 1948, uranium exploration and processing was opened to the private sector, and the Federal government offered special pricing incentives to the industry. Eldorado explored the Lake Athabaska deposits in northern Saskatchewan, and in 1953 opened the Beaverlodge mine. Other mines in the area soon followed. In 1953 also, the deposits in the Blind River - Elliot Lake area and in the Bancroft area of Ontario were discovered. Mines and mills were quickly developed in these areas.Canadian uranium production peaked at 15,900 short tons of U3O8 in 1959. In that year, uranium exports at $300,000,000 exceeded those of all other minerals in value. On October 1, 1959, Canadian uranium operations employed 13,900 people.Up to 1956, it was a seller's market. By 1958, world production of uranium was far ahead of requirements. Accordingly, in November of 1959, the USAEC announced it would not renew it's options for continued delivery of uranium from Canadian mines. This led to the ""stretchout"" of existing uranium contracts, and many mines were shut down (see Table 1) .In the early 1970's, a commercial uranium market seemed to be developing. In Ontario, at Elliot Lake and Bancroft, mines reopened. But competition was coming from the Athabaska basin of Saskatchewan. Currently it is these high grade, open pit deposits of northern Saskatchewan which are in the forefront of Canadian uranium developments. Canadian developments since 1942 reflect the political and market forces, as well as metallurgical progress and changes in environmental standards. This paper attempts to show these process changes in broad perspective."

Jan 1, 1987

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By P. W. Godbehere

"INTRODUCTIONMagnetic mill linings have been developed from an invention by Mr. Bertil Brandt, the originator of the Skega rubber lining. The OREBED magnetic mill lining is a concept in which rubber covered strontium ferrite permanent magnets are arranged on the inside wall of a mill shell so that they attract magnetically susceptible material be it ore, media or tramp, to form a protective layer over the magnets and to serve as an operating surface with indefinite life.Noranda Mines Ltd. through its associate Norcast Division of Noranda Metal Industries formed a joint venture with the inventors to market magnetic mill linings in North America. For the past twelve months trials have been undertaken in conjunction with Orebed Inc. to test and develop these linings for grinding mill applications at the Horne Concentrator. Two independent milling circuits are currently being operated, one treating a siliceous gold ore and the other a copper slag.This paper presents the results of the magnetic lining test programme to date."

Jan 1, 1983

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By B. Simser

Noranda?s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2004

By B. Simser, V. Falmagne

"Noranda’s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning.Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically."

Jan 1, 2004

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002