Search Documents

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By Johnny Lyons-Baral, John Kemeny, Don Kraemer

Ground vibrations from blasting can result in the degradation and failure of rock and soil exposures, as well as damaging neighboring houses and buildings. At the same time, vibration provides an opportunity to regularly monitor the rock and soil exposures. If a geophone or accelerometer is attached to a rock block or wedge on a mine slope, for example, then blast vibrations will regularly “sound” the rock block and the resulting vibrations can be used to assess the stability of the rock mass in the neighborhood of the accelerometer, as well as monitoring the properties of the blast. This paper describes the development of a wireless sensor network based on inexpensive MEMS accelerometers for blast monitoring and rock and soil structural health monitoring. The wireless sensors are placed at various locations in and around an open pit mine or quarry, and transmit data to a central source after ground vibration events occur. As described in the paper, a variety of wireless and non-wireless accelerometers were tested in actual field conditions. This includes the monitoring of over 30 blasts at an open pit mine in Arizona with as many as nine simultaneous accelerometers. Matlab was used to process all the data and develop innovative methods to view and interpret the data. This includes the use of the wavelet transform to determine resonance frequencies, and the use of both ground resonance frequencies and scaled-distance peak particle velocity (ppv) relationships to assess slope stability. As part of this research, a three-dimensional point cloud environment for viewing and analyzing the vibration data from the sensors has also been developed.

Jan 1, 2014

By Robert B. Hopler

Explosives, originally used only in fireworks and warfare, became legitimate contributors to human progress when miners in Eastern Europe began using them to break rock in the early 1600%. Since that time these powerful materials have had a dual role in the world: as agents of destruction in war, and as irreplaceable tools necessary to advance civilization. In the latter role, they serve as agents to enable mankind to produce metals, build roads, and drive tunnels. In other words, to provide those materials, services, and infrastructure without which the modern world could not exist.

Jan 1, 1997

By Robin Shepherdson

Security concerns have prompted the Department of Homeland Security to investigate the use of recording systems on all vessels holding materials used for blasting; a new regulation is expected in the near future. By measuring the strain developed in the legs of vessels with bolt-on sensors, it is possible to monitor the weight of vessel contents. Several companies make this type of sensor and recent versions give the required accuracy. This paper describes two generations of sensor, the second generation having a simpler method of installation that uses standard power and hand tools. Three types of indicator are available to monitor the material weight. 1) A simple electronic bar-graph indicator with a digital weight display. 2) A touch-screen display showing bar-graphs of multiple silos with digital weight displays plus their associated trend graphs, recent readings and an alarm log. 3) A data acquisition unit which acquires the weight digitally from up to 32 vessels and stores the raw and filtered date and time stamped data in a local computer database. This local computer then transmits the data via an Internet connection to a secure central database which allows the weights of all the storage vessels for a company to be viewed anytime and anywhere via the Internet. Historical trend graphs can be viewed and the data can be uploaded into an Excel file for further processing; for example to determine filling or discharge amounts. In addition, E-mail and SMS (Short Message Service) text alerts can be sent automatically when selected alarm levels are reached. Current research and development includes connection of vessels to the central database by a cellular wireless modem when a local computer or Internet connection is not available, as well as connection of remotely located vessels to a central point via “Wi-Fi bridge" radio data links. Future versions will include digital I/O (Inputs and Outputs) to record, for example, activation of filling and discharge devices as well as opening and closing of doors.

Jan 1, 2015

By Dennis R. Jr Bell

Before beginning any site development or mineral extraction activity, it has been well documented that it is first prudent to gain an understanding of the prevailing geologic conditions.Whether it’s identifying the depth to type of bedrock, or determining the quality and quantity of the in place mineral deposit, these factors should always be considered in a project’s fatal flaw analysis. In situations where there is limited subsurface information, geologic models have been proven to be one of the most valuable and cost-effective tools used by the developer and/or his consultant.

Jan 1, 1997

By Claude Cunningham

The primary reason for blasting is to fragment rock. In production blasting, the fragment sizes produced are known to exercise an overwhelming influence over working costs: handling costs and tonnage throughput are directly affected by secondary breaking, loading and crushing, all functions of fragmentation. In addition, particular size fractions are frequently of intense interest in terms of market or process requirements.

Jan 1, 1995

By Brian Carr

This workshop will display all of the existing products that are available as stemplug devices and discuss the general concept of the use of them. Actual results will be discussed along with several case histories. There will be adequate time for questions and answers.

Jan 1, 2000

By Ajoy K. Singh, B Mohanty, P K. Singh

A study was conducted to investigate the damage potential to underground multiseam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with much higher amplitudes compared to those in pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or higher. The vibration magnitude recorded was higher in upper-seam openings than in belowseam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle velocity-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for the safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.

Jan 1, 2011

By Steve Dillingham

Today, a typical blaster is likely to wear many hats, including, but not limited to, supervisor, risk manager, safety coordinator, explosives engineer, communicator, as well as professional decision maker. Simply put, a blaster in the new millennium is an all encompassing blast site manager. As you know, accidents on the blast site can range from blast crew injuries to blasting incidents resulting from vibration, flyrock, misfires, etc. Not surprising, the incidents can quite often be traced back to direct preventable human action on the blast site. They can, however, frequently be avoided, if responsibly identified early and managed properly by an efficient blast site manager. Your company cannot afford to simply employ blasters; good blast site managers are necessary to produce the safest results possible.

Jan 1, 2001

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By Richard R. Marston, Scott Herr, Steve Pries, Donald L. Jr Ewart

The purpose of this paper is to identify and examine alternative methods (other than shovel/truck stripping) of effecting the pre-stripping of consolidated overburden, in conjunction with dragline stripping operations, at surface coal mines. The analysis will be case study oriented with practical mining considerations and comparative economics being evaluated. Alternatives that will be examined include blast casting, dozer push, and multiple pass dragline sequences.

Jan 1, 1992

By Stanley Griff, William Herrera, William O. Seals

"The Navy initiated liquid propellant research in the early 1940's. The first promising Navy liquid propellant, Otto Fuel II, was developd in the early 1950 as a potential torpedo fuel. Later, the Navy developed a HAN based liquid propellant designated NOS-365, a hydroxylammonium nitrate, isopropylammonium nitrate and water formulation. A large gas volume generated by this propellant produced a large wake behind the torpedo. As one can readily understand, this negated the useof the propellant for this application. Recognizing the large gas volume as a desirable propulsion system for guns, the Navy embarked upon a gun propellant proqam. Utilizing a bulk loaded gun sysytem, the program failed when the gun was destroyed by the propellant detonating."

Jan 1, 1990

By Ruilin Yang

"Blast vibrations are essentially a strain/stress wave propagating in rock or structures inthe vicinity of a blast. However, blast vibration has always been quantified in terms ofpeak particle velocity (PPV) or acceleration (PPA), and a meaningful relationshipbetween blast vibration and strain/stress has not been established. The determination ofthe dynamic strain from blast vibration may improve quantification of blast damage andselection of a blast vibration limit for critical structures or high walls. Dynamic strainrelates to rock mechanics or material strength more directly than peak particle velocity(PPV). This paper documents a method to calculate the three-dimensional dynamic straintensor from recorded blast vibration signals. The method is based on determination of thedisplacement gradient at a point of interest for each time instance during the vibrationduration. The method to calculate dynamic strain is applicable to generic seismicwaveforms including near and far field blast vibration from a production blast withmultiple blast holes. In order to minimize measurement errors the specifications of thespacing between monitors and the sampling frequency of the vibration recording aredescribed."

Jan 1, 2012

By Dave Otto, Ron Elliot, Ed Hatch

This paper is a summary of the work carried out by an international team of specialists in the successful explosive compaction of the sand fill core of the Molikpaq offshore oil production structure. The sand fill core is an essential element for the stability of the structure. The sand core must resist liquefaction forces caused by heavy wave action, ice loading, and earthquakes. Explosive compaction methods were used to improve the stability of 220,000 cubic meters of coarse dredged sand placed in the core area. This project was challenging for a number of reasons. It was performed offshore in Russia, seven kilometers off the East Coast of Sakhalin Island. Logistics were a challenge, not just in getting the men and materials to the site, but also working with restricted headroom inside an operating oil drilling platform. This project called for the use of specialty explosives, strict blast vibration controls requiring a complex sequential blast design, and use of custom designed drill rigs. As Russian equivalent explosives were not available, the project involved getting approval for use of North American explosives in Russia, and use of a combined Russian - Canadian blasting crew. The blasting program was carried out successfully, meeting the required densification target _in a safe, effective manner, with no damage to the structure.

Jan 1, 2000

By Stuart Brashear, Eddie Colburn

The Birmingham Coal and Coke – Knight Mine is a single seam coal mine in central Alabama. As pit development progressed in 2013, concerns over increasing vibration levels resulted in modifications to the blasting program that inhibited shot size and coal recovery. By January 2014, while still over 1,400 feet (427 m) from the regulatory seismograph, vibration levels climbed above 70% of the mine permit limit, even with triple decking of holes and reduced burden and spacing. At this time the decision was made to commit to the use of signature waveform analysis and precision programmable electronic detonators to minimize vibration and maximize the amount of coal that could be recovered before vibration levels reached permit limits.

Jan 1, 2015

By Thomas Barkley

Recent developments in hardware and software have made accurate measurement of Underground Face (Development) Drilling a reality. New and compact laser profiling equipment makes it possible to measure drilled material left on the face as well as the actual tracks of the holes drilled in the rounds. Utilization of these available technologies makes it possible to correctly define the drilling accuracy and the blasting pull. Through the use of actual face round measurements, I will show the level of definition and amount of information that can be collected.

Jan 1, 2003

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Gordon Revey

The challenge of managing blasting risk, types of risk, public perception, and a system for managing risk were covered in the first part of this article in the May/June 2000 issue of the Journal of Explosives Engineering. This final part of this two-part series provides a method for identifying specific blasting risks and reviews the importance of community relations.

Jan 1, 2001

By Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and the field controls used on the shot. This point cannot be over emphasized because when the geometry is not measured and/or field controls are not properly implemented, it can often have devastating effects on the final blast results. Thus drilling accuracy, tiont row burden control, explosive confinement, energy distribution, explosive selection, timing and structural geology become critical parameters in the design of successful blasts. Understanding the actual dynamics of the blast and why certain results were achieved is the fast step in optimizing a blast design. As stated by R. Frank Chiappetta, “Of all the blast monitoring systems available today, high speed videography still remains as the best stand alone instrumentation system for blast diagnostics.” Over the past years I have analyzed hundreds of blasts using either high-speed lowcams (500 frames per second) cameras or standard digital (30 frames per second). These analyses confirm, without a doubt, that shot geometry, in combination with structural geology, is the most important factor in overall blast results. Drilling accuracy is the single most important component in efficient blasting. Having equal mass associated with an equivalent energy is the basis in which blasts are designed. When drilling inaccuracy or borehole deviation occurs, not only is the energy unevenly distributed, but the basis of all design calculations becomes invalid. Over the past several years, quarry and mining operations have employed the use of boretracking measuring devices to measure borehole deviation and hole toe locations. In cases of operations using top hammer drills, it was discovered that the amount of deviation was significant and far greater than they believed they had. Set up error, improper drilling techniques and bit wear were some of the contributing factors. Through video anaysis of boretracked blasts, blast results were directly linked to drilling ..accuracy. The comparisons here took into account blast design, energy factors and hole sequencing.

Jan 1, 2000