Search Documents

By Fredrick M. Ryan

Present indications are that in about 2-3 years phosphor tags will be required in commercial explosives. A permissible 254 run ultraviolet lamp assembly has been developed to permit mine inspectors to detect such phosphor tags and therefore to establish if non-permissible explosives were used. This new lamp is powered by a Miner's cap battery without interference with the normal lighting requirements of the cap lamp battery. It is compact, light, and rugged with very high ultraviolet output.

Jan 1, 1977

By Terry P. Medhurst, Stuart A. MacGregor, Peter J. Hatherly

In addition to fractures and joints, compositional factors and bedding influence the strength of clastic sedimentary rocks. Rock mass rating schemes must therefore consider all of these factors. In this paper, a rating scheme for clastic sediments based on geophysical measurements is described. Geo-physical logging allows an approximation of rock com-position to be obtained and an assessment of bedding frequency and laminations. Velocity measurements incorporate the effects of fracturing. The rating requires scores for the intact rock, bedding/cohesion, and defects. These are combined to yield a Geophysical Strata Rating (GSR). Determination of the GSR is objective and repeatable. GSR values are typically between 20 and 80 and can be related to the Coal Mine Roof Rating.

Jan 5, 2007

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow in by the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

By F. J. Prokoski

The COALSTAR Project, which operated from November 1981 to December 1982, was a research and development project aimed at providing a reliable and inexpensive means of monitoring various waste site conditions via the GOES satellite system. The GOES system provides data transfer from unattended isolated sites where neither power nor telephone lines exist. The reliability and resolution of the data received while using the satellite link were excellent; however, the site instrumentation gave considerable trouble. The disastrous failure of a large coal waste embankment in 1972 led the Bureau of Mines to undertake a comprehensive program to reduce the likelihood of such an occurence again. Part of this program involved the installation of instruments to monitor the stability of a specially-selected embankment operated by Armco Incorporated near Montcoal, West Virginia. Initially, the instruments were monitored by normal telephone lines and used normal commercial power from the local utility. The project described here was initiated to replace this monitoring system with an unmanned, solar-powered data collection system which transmitted data via satellite to a central computer facility. The satellite data network is the National Earth Satellite Service of the National Oceanic and Atmospheric Administration.

Jan 1, 1984

By James D. Eklund

Towards the goal of improving safety, economy and efficiency of scaling in underground metal/nonmetal mines, Battelle developed a combination prying/hammering scaling tool. A prototype was subjected to limited testing 1) to verify its operational functions and 2) to assess its potential capability in future underground testing.

Jan 1, 1983

By W. D. Bensema

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550-and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines, describing mining methods and performance at individual mining operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and performance. Limestone deposits in Iowa are extensive and reserves are large. Most of the past production came from the eastern third of the state, although over half of the counties in the state have produced, or are now producing limestone. The stone is used as aggregate, road metal, agricultural lime, riprap, fluxing stone, railroad ballast, and in the manufacture of cement and lime.

Jan 1, 1962

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By J. McCoy

Charged sprays and fog have been evaluated for reducing respirable dust concen¬trations. Charged spray technology was reviewed for effectiveness, equipment and theoretical considerations. A mathematical model was developed for predicting dust reduction effects. Laboratory tests were made showing charged spray is considerably more effective at reducing dust on a unit water basis than hydraulic spray. Positive and negative sprays are equally effective. Combined polarity sprays are considerably less effective than either polarity alone. Little difference in effectiveness by dust type was observed. The charged cloud can present a spark hazard in explosive atmospheres. Due to this spark hazard from the charged droplet cloud this technique must not be used in gassy mines. Predictions were made for field test conditions but confirmation was impossible due to particles resulting from dissolved solides in the spray water. Dissolved or suspended solids in atomizing sprays can result in an increase of the respirable dust burden. Charged sprays are an available dust control technique best suited to applications where water usage must be limited and long contact time between spray and dust is possible.

Jan 1, 1983

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By V. A. Marple

At the Twin Cities "lining Research Center (TCMRC) a project is underway to determine how varying the parameters of a coal-cutting process would affect the amount and the size distribution of the generated dust. The cutting parameters being investigated are the cutting speed, depth of cut and shape of the cutting, tool. To accomplish this research ft is necessary to collect and transport the coal dust venerated at the cutting tool to measuring instruments for analysis. The purpose of this contract was to develop and deliver a system of instruments for measuring the size distributions of the generated coal dust. The instruments employed are essentially those developed for particulate air pollution measurements (1, 2). The instrument system covers a particle size range of 0.005 to 20 microns and is capable of performing in situ measurement and presenting data in real time.

Jan 1, 1974

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By Martin Smirlock

A novel instrumentation system has been developed which enables simple, quick, and accurate measurement of vehicular dynamics within low speed ranges. The system, consisting of a microwave transceiver and microprocessor data acquisition and reduction system, measures the deceleration dynamics of low-speed mining and construction equipment. It makes the basic measurement, calculates key parameters such as average deceleration, initial velocity, stopping distance, and brake system delay time, and produces autoscaled graphs of velocity, acceleration, and displacement versus time.

Jan 1, 1981