Search Documents

By J. H. East, D. Harrington

"INTRODUCTION Shaft mines, coal and noncoal alike, have a common hoisting problem that remains largely unsolved - how to obtain a mechanical device that will suspend a cage or skip in a mine shaft if the hoisting rope should break or become detached from the cage or skip and that will function effectively under all conditions of service. Safety catches, or safety dogs, as they are commonly named, are installed on nearly all mine cages and many skips operating in American mines, but often, if the hoisting rope breaks, the cage or skip falls to the bottom of the shaft in spite of safety devices, causing much property damage and often fatalities.Available information relative to safety catches for mine cages and skips, desirable characteristics of safety catches and methods of testing safety catches to determine whether they are functioning correctly has been assembled in this publication for the convenience of those responsible for the safe operation of mine cages end skips and, more particularly, to focus attention on the need for a device that actually will stop and suspend a falling cage or skip under all conditions of use and do it without killing or maiming the occupants."

Feb 1, 1948

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By J. H. East, D. Harrington

"INTRODUCTION Mining at its best is not a clean occupation for either surface or underground employees; and this applies alike to coal, metal, and non-metallic mines. The employees are handling minerals that have been blasted, or broken by some means and are subjected to mineral dust, whether it is coal, quartz, or talc. The employees usually wear clothes specifically adapted to the work in which they are engaged, and frequently these clothes are not suitable for use away from the mine. Many mines are wet, and employees must wear rubber boots to remain at least partly dry, and even on relatively dry mines, some parts of the mines usually have water falling from overhead, there are accumulations of water, or the floor or other surfaces are wet or muddy, Some mines are dusty, and the air-borne dust quickly settles on the clothes and body of the miner, especially, when he is working in confined areas, or in places that are hot, humid, or poorly ventilated. Most occupations around a coal tipple, anthracite breaker, or a mill at a metal or nonmetallic mine have their own problems of cleanliness as to skin or clothes or both. Mining in any of its phases is inherently dirty work, and the employees dress accordingly while at work.In the early stages of mining it was the custom or workers to wear their dirty clothes home and change there. This necessitated their going home after work in dirty clothes which were usually damp from perspiration or from contact with wet or muddy matelials or surfaces, and, in addition to being inconvenient this was a frequent cause of colds, pneumonia, other pulmonary diseases or, possible skin ailments. Men working in very wet mines found that it was more satisfactory to change into dry clothes in the boiler room at the mine after work and allow their wet clothes to dry overnight. The mining companies later provided the first of the so-called ""dry-houses"" which were heated but had, few, if any, conveniences, such as showers, lockers, or latrines. The miners changed into dry clothes after work, but would not bathe or ""clean up"" until they reached their homes. Later, progressive mining companies provided bathing facilities for the employees, and eventually the present modern wash and change houses were evolved. Unfortunately, many mines, still have no bathing accommodations, and many have only makeshift accommodations."

Dec 1, 1947

By Richard Stayner

Suspended seats perform two functions: Reduce effect of occasional large bumps; Reduce more continuous vibration at a lower level. The former needs high damping. The latter needs low damping. For most mobile work machines the inevitable compromise is generally better than a simple cushion seat, because that amplifies vibration at around 4 Hz which is a sensitive frequency for human vertical WBV. Why have standard tests for seat suspensions? • Seat suspensions are non-linear so any measure of performance depends on operating conditions. For comparison these need to be defined. • Seat manufacturers need benchmarks for product development; • Machine makers choose dynamic characteristics appropriate to their products; • Occupational health specialists wish to control operator exposure to Standard tests should be representative, repeatable and reproducible. These requirements are reviewed in relation to the history of seat test standards and the current position. Current position and history The current position is that we have standard tests for seats for agricultural tractors, earthmoving machinery, industrial (fork-lift) trucks. These tests comprise measurement of vibration transmission and of the rate of damping. Current standards developed as the technology developed, starting around 1960: 1. Test on machine driven over standard surface1. 2. Test on shaker reproducing standard surface. 3. Shaker input replaced by representative spectrum2. 4. Human subject replaced by dynamic dummy. (Not yet settled). Are standard tests representative? The development process has gradually moved seat tests further from reality. 4 hr samples of work exposure suggest that seats do not on average provide large reductions of vertical WBV3. For specific magnitudes of vibration they can work well. For low vibration, performance is reduced by friction and for severe vibration by length of travel. Recent work has led to a new test to quantify how a suspension controls over-travel 9.

Jan 6, 2006

By L. L. Hirst

Liquid fuel oils possess certain advantages over solid fuels. Ease in handling, precision temperature control, and almost complete freedom from ash are among those considered when a liquid fuel is selected for use in industrial processing. In some instances these fuels are desirable because more heating units can e packed in a Given space where space is limited, as on snips. In other cases the' are chosen because of lower actual cost per British thermal unit absorbed, or for control of the flame to increase the capacity of furnaces, as in steel and refining.

Jan 1, 1948

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By Mark L. Chatman

This report presents an economic mineral assessment and Inventory of mines and prospects In the approximately 176,000-acre Patagonia Mountains-Canelo Hills Unit of Coronado National Forest. Deposits or areas most likely to experience future development are characterized in terms of their economics, based on data acquired by the author from a variety of sources, and supplemented by USBM field data collected by other workers in 1990 and 1991. Numerous mine maps, rock-chip sample assays, and detailed descriptions of mine and prospect sites are in this report and appendixes. Heavy but sporadic mining, mainly between the 1850's and 1950's was nearly all confined to the Patagonia Mountains. High-grade sulfide veins, replacements, and skarn deposits accounted for most of the production, which included large quantities of zinc, lead, copper, and silver, and considerable quantities of gold. Small Quantities of molybdenum, manganese, tungsten, and placer gold have been mined. Most of the traditionally mined metalliferous sites will not see future activity due to the low tonnages present and removal of most high-grade rock. Possible future development areas include copper porphyries and breccia pipes; most are too deeply buried for current development. Localities where similar deposits may be concealed are identified.

Jan 1, 1994

By P. -É. Boileau, VibRG, S. Grenier, M. Smets, T. Eger, J. Stevenson

Load-haul dump vehicles (LHDs) are used to move waste rock and ore in underground mining operations. The LHD is designed for bi-directional operation and the driver sits sideways to the direction of travel. LHD operators have higher reports of low back pain and neck discomfort than other mobile equipment operators who do not sit sideways in the vehicle, but are exposed to whole-body vibration (WBV)1. Exposure to WBV is linked with reports of lower-back pain, neck problems and spinal degeneration2,3. Static sitting postures, sitting with the neck and back twisted, and sitting with the back in an unsupported posture are also linked with an increased risk of developing back pain4. The objective of this study was to determine typical vibration exposure levels and driving postures for LHD operators. Methods Whole-body vibration exposure was measured at the seat-pan, in accordance with the ISO 2631-1 standard5, on seven LHD vehicles with a 10 yard bucket haulage capacity. Vibration data were recorded with a Biometrics™ DataLog II (P3X8) and stored on a 128 Mb Simpletech™ multimedia card. Comparisons were made to the ISO 2631-1 Health Guidance Caution Zone (HGCZ) in order to determine potential injury risk. Operator posture was monitored with three digital video cameras which were secured inside each operator’s cab to the top left corner, top right corner and back right corner. Reflective tape was placed on each driver’s shoulders, head, and back in several locations and in several locations on the vehicle seat in order to aid in posture coding. Posture coding was performed with 3DMatch v4.50 multiple video view analysis feature. Vibration measurement and posture recording occurred simultaneously for 60 minutes while the LHD operator performed typical duties. Results and Discussion Results indicate LHD operators may be exposed to whole-body vibration levels putting them at risk for injury (Table 1). According to ISO 2631-1 the frequency weighted acceleration values corresponding to the lower and upper limits of the HGCZ (for an 8 hr exposure duration) are 0.45 and 0.90 m/s2 respectively5. Six of the seven vehicles showed exposure levels within the HGCZ defined for 8 hours. Preliminary video analysis indicated LHD operators were exposed to potentially harmful levels of WBV while adopting asymmetric postures (Table 2). For example, one LHD operator (Figure 1) worked with his neck twisted greater than 40 degrees for 93 % of a 60 minute work cycle. According to the Swedish National Work Injury Criteria, neck rotation should be less than 15 degrees if the motion is required for greater than 80% of the work time6. Results of this study highlight the need to further examine the contribution of non-neutral working postures and

Jan 6, 2006

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By A. C. Fieldner

THE Bureau of Mines has received many requests for Information concerning the methods its laboratories use for analyzing coal and coke and determining their heating value. The fuel investigations now conducted by the Bureau of Mines are an outgrowth of the work undertaken at the Government coal-testing plant erected in 1904 at the Louisiana Purchase Exposition in St. Louis, and the methods for proximate and ultimate analysis of coal used by the Bureau of Mines are based on those originally adopted by the chemists of the coal-testing plant and followed in the subsequent chemical work of the Government fuel-testing plants at St. Louis, Mo., Norfolk, Va., and Pittsburgh, Pa. The many valuable suggestions and criticisms received from N. W. Lord, director of the School of Mines, and from E. E. Somermeier, professor of metallurgy, of Ohio State University, at that time, are greatly appreciated; development of many of the methods for the proximate and ultimate analysis of coal now used by the Bureau of Mines is chiefly clue to these men.

Jan 1, 1951

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 29 countries: the 12 nations of the European Community (Belgium, France, the Federal Republic of Germany (FRG), Italy, Greece, the Netherlands, Denmark/Greenland, Spain, Portugal, Luxembourg, The United Kingdom, and Ireland); 6 of the 7 nations of the European Free Trade Association (Sweden, Norway, Finland, Iceland, Austria, and Switzerland); Malta; the 8 Centrally Planned Economies of Eastern Europe (the German Democratic Republic (GDR), Poland, Yugoslavia, Albania, Hungary, Czechoslovakia, Romania, and Bulgaria); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Com-munity (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to its ex-colonies in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). There is an important reason for this since Western Europe lies somewhere between Japan at one extreme and the United States and the U.S.S.R. at the other extreme as regards the availability of natural resources.

Jan 1, 1992

Multiple-seam interactions are a major ground control hazard in many U.S. underground coal mines. In some U.S. coalfields, particularly in central Appalachia and the West, the majority of today’s mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously disrupt mining operations and threaten the safety of miners. In early 2006, a West Virginia coal miner was killed by rib roll that occurred in a high-stress zone beneath a remnant structure in an overlying mine. Fortunately, not every multiple-seam situation results in hazardous conditions. Indeed, the vast majority do not. For the past several years, the National Institute for Occupational Safety and Health has been conducting research to develop better techniques for predicting the location and severity of multiple-seam interactions. During this investigation, more than 50 mines were visited across the U.S. coalfields. Nearly 300 case histories were collected and analyzed using multivariate statistical techniques. The study also employed the numerical model LaM2D to estimate the multiple-seam stress, the Analysis of Longwall Pillar Stability (ALPS) and the Analysis of Retreat Mining Pillar Stability (ARMPS) programs to determine pillar stability factors (SFs), and the Coal Mine Roof Rating to measure roof quality. The study focused on the two most common types of multiple-seam interactions: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the main concern; and • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. For the first time, however, it was possible to quantify these effects in terms of the equivalent thickness of interburden needed to compensate for them. The study also found that pillar design is a critical component of multiple-seam mine planning. Many of the failed cases involved pillars whose SF seemed inadequate once the multiple-seam stresses were accounted for. Weaker roof was also found to significantly increase the risk of multiple-seam interactions. The most important result of the study is an equation that predicts the critical thickness of the interburden required to minimize the likelihood of a multiple-seam interaction. This equation was incorporated into a step-by-step methodology that allows mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. Such measures could include installing cable bolts or other supplemental support, increasing the pillar size, or changing the mine layout to avoid the remnant structure entirely. These Proceedings also contain several previously published papers that cover other facets of multiple-seam mining research. Two papers describe the LaModel family of software developed by Professor Keith A. Heasley of West Virginia University. The LaModel programs were designed for calculating the stresses and displacements in coal mines or other thin, tabular seams in layered media. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D, by contrast, implements a simplified two-dimensional model that is suitable for quick approximations of the multiple-seam stresses and strains. Three additional papers in these Proceedings describe the extensive multiple-seam experience of the Harris Mine, examples of extreme multiple-seam mining from the central Appalachian coalfields, and longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining.

Jan 5, 2007

By John D. Bardill

This report covers magnetic surveys in the Dannemora arca , which was part of a general survey of magnetite deposits in New York started in 1943 . The objective of these surveys was to afford a basis for the selection of exploration projects .

Jan 1, 1947

By Doss H. White

The value of non fuel mineral production in Alabama in 1991 was $539.9 million, a decrease of $20.7 million, a result of the nationwide recession that was felt throughout the State's economy. The 3.7% decline in mineral sales was due primarily to a slowdown in construction, which had a major impact in the construction minerals mined instate. Production and sales of crushed stone and sand and gravel fell significantly below the value reported in 1990. Despite the recession, Alabama moved from 21st to 20th place nationally in mineral value. Mineral industry developments in 1991 were primarily in the metals manufacturing sector. Reynolds Metals Co., Sheffield, celebrated 50 years of operation in Alabama. During the November celebration, the company dedicated a $121 million expansion that included a new casting facility and sheet rolling operation. Gulf States Steel Corp., Gadsden, completed the first full year of operation of its new multimillion-dollar continuous caster.3 The Foundry of the Shoals Inc., Florence, replaced two coke-fired furnaces with electric furnaces.

Jan 1, 1993

By J. C. Edwards, C. C. Hwang

In ventilated tunnel fires, smoke and hot combustion products may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of this reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels and building corridors. In the present study, conducted by the National Institute for Occupational Safety and Health, a CFD program (fire dynamics simulator) based on large eddy simulations (LES) is used to model floor-level fires in a ventilated tunnel. Specifically, the critical ventilation velocity that is just sufficient to prevent the formation of a reverse stratified layer is simulated for two tunnels of different size. The computer code is verified by checking the computed velocity profile against experimental measurements. The CFD results show the leveling-off of the critical ventilation velocity as the heat release rate surpasses a certain value. At this critical ventilation, the ceiling temperature above the fire reaches a maximum for both tunnels. The velocity leveling-off can be explained from this observation. An extended correlation of Newman (Combust. Flame 57 (1984) 33) is applied to the temperature profiles obtained by CFD. At the critical ventilation, temperature stratification exists downstream from the fire. The computed critical ventilation velocity shows fair agreement with available experimental data taken from both horizontal and inclined fire tunnels. The CFD simulations indicate that the Froude modeling is an approximation for tunnel fires. The Froude-scaling law does not apply to two geometrically similar fire tunnels. The CFD results are compared with two simple theories of critical ventilation by Kennedy et al. (ASHRAE Trans. Res. 102(2) (1996) 40) and Kunsch

Objective: To help prevent squeezes, collapses, and other pillar failures through better pillar design, thereby enhancing safety for underground mine workers.

Jul 1, 1997

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By C. Edward Chamberlain

A Bureau of Mines procedure was developed for the analysis of volatile matter in airborne coal dust-rock dust mixtures prior to, and resulting from, coal mine fires and explosions. Dust in the 10-to 20-mg weight range can be analyzed. Volatile matter is determined by a greatly scaled-down version of the empirical macro-scale method used by the Bureau. The alkaline earth carbonates in the rock dust are dissolved in acid prior to the volatile matter determination of the residue, and the rock dust content is calculated from the analysis of calcium and magnesium by atomic absorption.

Jan 1, 1974

By H. Polat, Q. Hu, M. Polat, S. Chander

"The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank.Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTIONWater spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles."

Nov 1, 1995