Search Documents

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

By James H. Russell

The Bureau of Mines, U.S. Department of the Interior, in cooperation with the Department of Energy, has attempted to increase the activity of nickel catalysts for converting synthesis gas, derived from coal, to a substitute natural gas. This report describes the effects of low-level additions of B, Ca, Ce, Co, Mn, Mo, Pd, Re, Ti, Y, Zn, and Zr on the methanation activity of Raney nickel. The methanation rate at 320° C and the resistance to poisoning by 2 ppm H2S were used to compare catalysts. The effects of the additions were small, and the experimental variances were large, necessitating the use of statistical methods to identify significant effects. Co, Ti, Y, and Zn improved the resistance to H2S poisoning, but only Co improved the methanation rate In some individual catalysts containing Ca, Mo, or Mn, both the methanation rate and resistance to H2S poisoning were improved.

Jan 1, 1980

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 5,640-acre Soda Mountain Wilderness Study Area (OR-011-017), in order to evaluate its identified mineral resources. The study area is located in Jackson County, OR, about 30 miles south-east of Medford. The study area covers most of the south-facing slope of 6,071-ft Soda Mountain. Geologically, the area is underlain by Oligocene to Pliocene basaltic andesite flows and less extensive intrusive rocks of the western Cascade Mountains. In addition, there is a 3/4-mile-diameter area of kaolinized and silicified rhyolite tuff, which appears to have intruded the andesite, and is host to epithermal gold mineralization.

Jan 1, 1989

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1984

By Jacqueline H. Jansky

The Bureau of Mines conducted a study to determine the relation-ship between geologic features and linears. Cleats, kettlebottoms, and roof rolls were mapped and superimposed on the linear plots for a coal mine in West Virginia. No clear relationships were evident. This may be due, in part, to the mining practice of leaving head coal, which obscures geologic features that may exist in the roof. Future studies should concentrate on mines where roof is extensively exposed.

Jan 1, 1982

By Michael D. Fenton

Detailed comprehensive assessment of the performance of Afghanistan&apos;s mineral industry during 1987 is virtually impossible, owing to the paucity of reliable published information. It was evident, however, that the level of civil disorder, now in its eighth year since the arrival of significant numbers of Soviet troops, was in actuality little removed from open civil war. Insurgents controlled substantial areas of the country and imperiled any industrial activity in many places. Assistance programs by the U.S.S.R. and other Eastern European nations were directed at developing the country&apos;s meager mineral industry, but the economy was generally viewed as chaotic. The inflation rate was somewhere between 20% and 30%; major food shortages contributed to the discontent of the population, and numerous villages were devastated by Soviet and Afghan Government campaigns to destroy the insurgents and cut their supply routes. Moreover, proposals by the Soviets and the Kabul Government aimed at reducing tensions with the rebels and scaling down the warfare seemingly were taken by the opposition as signs of weakening by the Soviet-backed Government, and rather than reducing aggressions, seemed to heighten insurrectionist activities. Efforts to entice the substantial number of Afghans who have fled to nearby areas of Pakistan and Iran to return to their country seemingly were failures, and indications near yearend that the Soviet Union might soon begin withdrawal of its occupation force of nearly 120,000 did little if any to reduce disorder.

Jan 1, 1989

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By C. P. Bowie

[Frequent accidents in the transportation and. handling off petroleum and its more volatile products, serve as a reminder that this is indeed a hazardous undertaking and should always be conducted with due caution. On October 4, 1920, vapors in the held of the British tanks steamer G. R, Crowe became ignited and, caused an explosion which, it is reported, killed 5 men, injured. 40 others and endangered the lives of some 300 more. On November 10, 1920 the Morgan, Line freighter El Mundo was almost totally sot destroyed in New York harbor by fire caused by an explosion of gases in a fuel-oil tank. These two disastrous explosions emu emphasize the ever- present danger attending the use of petroleum products. This is also shown by the frequent occurrence of minor fires and explosions, caused by careless handling of baseline, which result in loss of life or serious injury to railroad employees, to oil-tank drivers, and to individuals in various walls of life. Statistics indicate that the lighter cuts of petroleum products, because of fire hazards, are dangerous, and are so considered by the railroad and other transportation companies. According o the Bureau of Explosives (Bar-eau of Explosives Report No. 13 p. 7) during 1919 transportation of gasoline in the United States resulted in 172 accidents, causing 2 deaths and 31 injuries, and a property loss to the extent of $687,966. Among the causes of ignition, an open light in the vicinity of the container stands out most prominently.]

Jan 1, 1920

By George A. Morgan

Mineral production was confined to out-put of cement and gravel. However, exploration was being conducted by the U.S.S.R. and the United Nations Development Program. Development of a domestic limestone deposit and crude oil from an offshore oilfield was underway. Benin&apos;s currency remained fixed to the French franc. The gross domestic product (GDP) was $977 million in 1981, the latest year for which information was available. 2 COMMODITY REVIEW Cement.-Construction of a cement plant with 500,000 tons per year capacity neared completion at Pobé. The operator of the plant, using locally produced limestone, was the Societe des Ciments d&apos;Onigbolo, a joint venture between Benin and Nigeria. Nigeria was expected to utilize most of the cement produced. Equipment for the plant included a 1,600-ton-per-day, oil-fired pre-heater.

Jan 1, 1984

By C. D. Litton

The results of full-scale fire tests are used to determine optimum distributions of fire sensors for the protection of conveyor belt haulageways in underground coal mines. Empirical relationships are derived that relate the spacing of fire sensors to the rate of development of the fire hazard. For this application, a critical fire size is defined as that size of fire for which belt ignition and subsequent flame spread down the belt is assured. Detection and alarm, regardless of sensor type or sensing methodology, must be achieved at some point in time before the critical fire size is reached. Based upon this approach, it is found that the horizontal spacing for products-of-combustion sensors is in the range of 300 to 600 meters, while the required thermal sensor spacing is found to be ~4 meters or less. Additional design criteria are discussed for product-of-combustion fire sensing systems.

Jan 1, 1982

By M. B. Cooke

An analytical method for the determination of the gum-forming material in gasoline has been developed by the Bureau of Mines, during a study nor in progress to determine the best rays for elimination of such constituents from gasoline. This method is similar in principle to that previously described by Smith end Cooke,2 which involved evaporation of e sample of gasoline in a small glass dish. The evaporation was started on an actively boiling steam bath and completed in an air oven at 105°C. In the improved method described below, the stem bath has been replaced by a steam heated oven in which an inert atmosphere is maintained. Air is excluded from the oven, consequently the precision of the determination is increased. Furthermore, evaporating dishes different from those previously described may be used.

Jan 1, 1925

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By d&apos, Kathleen J. Amico

THIS summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S mineral production also is included.

Jan 1, 1964

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result-ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coal bed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beckley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By Ralph L. Brown

"IntroductionThe accumulation of gummy and resinous deposits in consumers' gas meters began to assume serious proportions about 1917. As the trouble developed and spread in the years following, it manifested itself in several ways, which ultimately began to the expressible in distinctly economic terms, more specifically in terms of costs; in 1922 an organized and fundamentally based investigation of this trouble was begun. In an earlier paper*** a short statement of the occurrence and costs of the deposition was given and at the same time an analysis of the problem, as well as well as a general plan of attack, was presented. That plan included two general phases, first, a chemical study of typical was 1 quarry or 2 cosinous content , mauformly consituents, rmln and selected subjects; and secondly, a comparative survey of plants affected and sufficient therewith, attention being paid to construction, operation, meter conditions and related data. In reporting progress in the axtual investigation, it was definitely set down that the basis of the gummy deposits was the unsaturated hydro consulting from the carburxtion of the water-gas with oil. That the presence of oily-gas condensate was closely associated with and largely"

Jul 1, 1923

By Abdo F. Bayazeed

A survey of the underground injection of steel processing waste pickle liquor (WPL) was made by Bureau of Mines engineers. Hydrochloric and sulfuric acids WPL are being injected into deep wells completed in the Cambrian age Mt. Simon Sandstone Formation in Illinois and Indiana. The Mt. Simon Formation ranges up to 1,800 feet in thickness. The average depth of WPL injection wells is 4,000 feet, and injection is mostly by gravity flow at rates as high as 4,000 barrels per day. The details of the design and operating history of a WPL well located near Gary, Ind., are discussed. Laboratory tests showed that the Mt. Simon Sandstone is sensitive to fresh water. The adsorption of iron and neutralization of acids by sandstone cores from deep wells and an outcrop were determined.

Jan 1, 1973

By A. W. Henderson

The growing importance of halide metallurgy for preparing high-purity metals has stimulated research to extend halogenation reactions to the direct extraction of metals from low-grade sources. This Bureau of Mines investigation involves a pioneering study of chlorination reactions in the presence of a fluorine donor. Tin slags containing tantalum and columbium and a zircon concentrate containing a relatively high ratio of hafnium to zirconium were studied. Direct chlorination of these materials at 500° C. yields only a 5-percent conversion of tantalum and columbium or zirconium and hafnium to anhydrous chlorides. This investigation showed that small additions of calcium fluoride to the reaction increased the recovery of tantalum and columbium to 95 percent and the recovery of zirconium and hafnium to 27 percent. These results were achieved with ratios of calcium fluoride to mineral or slag of only 0.2. Silica, the major impurity in the materials studied, was found to be converted to silicon tetrafluoride during chlorination in direct proportion to the quantity calcium fluoride added to the charge. However, large additions of calcium fluoride decreased the volatility of the resulting halides of tantalum, zirconium, and hafnium. Smaller amounts of calcium fluoride also favored recovering minor metal constituents in the zircon concentrate (uranium, thorium, and rare earths).

Jan 1, 1962