Search Documents

By H. S. Price

This report discusses the development of a mathematical model that describes the flow of methane only and methane and water in a coal bed during mining operations. Because of the complex geometry, boundary conditions and fluid properties, the model is based on a numerical solution to the equations describing flow. The goals for the development of this model and requirements to which it complies are for the most part expressly stated in Request for Proposal No. 50110752. In addition to the capabilities specified under the scope of work the model can handle an anisotropic porous medium and a source term has been added which will simulate, somewhat, the effects of desorption. This term will be pressure dependent. The effect of time on such a term is only taken care of in the change of pressure with time. This source term will have the dimensions of Mcf/day/Mcf pore volume. It will be a part of the input data to be supplied by the user and will be entered as a table of rates versus pressure. These models consider the fracture system as the main porosity. All computed results pertain to the fractures. The source term mentioned above represents the flow from the matrix porosity into the fracture. Such flow should be small compared with the flow between fractures since these models handle only one porosity structure system.

Jan 1, 2012

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

By M. M. Fine

Research on the solid-fuel reduction of Knob Lake iron or was conducted to upgrade lean and high-grade ores and recover metallized products suitable for ironmaking or steelmaking. The program included bench-scale tests plus a number of continuous campaigns in a 34-inch by 36-foot rotary kiln. In the laboratory, metallizations in excess of 90 percent were achieved by reduction of crushed ore with lignite at 950° C. Subsequent grinding (to minus 200 mesh) and wet magnetic separation yielded concentrates analyzing less than 3.0 percent SiO2 and more than 90 percent Fe. Virtually complete recovery of the iron occurred. During early continuous tests the crushed ore created a serious ringing in the kiln which was solved by balling the fines with bentonite. Unfortunately, at this temperature (950° C) the bentonite militates against the concentratability of the metallized product. For example, a run on direct-shipping ore produced concentrates of 89.5 percent Fe and 4.5 percent SiO2. At 500° C the adverse effect of bentonite disappeared and concentrates of 88.4 Fe and only 2.5 percent SiO2 resulted. However, with comparable feed r Los, the metallization dropped to 73 percent.

Jan 1, 1969

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

By W. R. Hardwick

This paper describes open-pit mining methods and practices at Copper Cities Division of Miami Copper Co, in Gila County, Ariz. It is one of a series being prepared by the Burea of Mines on mining methods, practices, and costs in various mining districts of the United States. A similar program, conducted from 1928 to 1939, provided technological information on the development and conservation of our mineral resources and assisted operators and engineers in evaluating and developing new mineral deposits. This circular contains a brief history of the district and describes the Copper Cities deposit, with particular emphasis on a detailed description of those characteristics--physical, economic, or engineering--that affect the choice of mining method. Prospecting and exploration, sampling and estimation of tonnage and values, development, and mining (including breaking ground, loading, hauling, ore control, and auxiliary operations related to mining) are described, Percentage of extraction, production rate, safety, first aid, Eire prevention, mine organization, and processing plant are discussed briefly, The final section gives such costs, on a percentage basis, as are available for publication. Where relevant, some information on the Castle Dome mine is included.

Jan 1, 1960

By W. F. Watts

This report describes the Mine Inspection Data Analysis System (MIDAS) developed by the Bureau of Mines to analyze the records of industrial hygiene samples collected by the Mine Safety and Health Administration (MSHA) in metal and nonmetal mines. MIDAS is the first system capable of sorting, editing, analyzing, and reporting these data. It is also the first system designed to be used by a number of Government agencies. At present the system contains 225,000 personal and area samples for 61 contaminants in 45 industries. The records date from 1974 to early 1980, and MSHA plans to provide yearly updates to the system. This report presents preliminary analyses of dust exposures and discusses the potential uses and limitations of these data. Analysis of the dust data for 1978 and 1979 showed that bagging had the highest percentage of dust overexposure. Morn than 40 pct of the 1,536 respirable quartz dust, total nuisance dust, and total silica dust samples exceeded the MSHA exposure limit. Other dusty occupations are ranked according to their percentage of overexposure.

Jan 1, 1981

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

By Jürgen F. Brune, Liming Yuan, Alex C. Smith

To provide insights and assistances for the optimization of ventilation systems for U. S. under-ground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study is being conducted to investigate the effect of the ventilation scheme on the prevention of spontaneous combustion in longwall gob areas. This report focuses on the flow patterns within the gob under three different ventilation systems; one-entry and two-entry bleederless systems as well as a three-entry bleeder system. The gas flow in the caved gob area is simulated as a laminar flow through porous media while the gas flow in ventilation airways is simulated as a fully developed turbulent flow. The air flow patterns are visualized using flow path lines. Air velocity contours and vector data are also obtained. The possible location of critical velocity zones where the gob is most liable to spontaneous heating is discussed.

By S. J. Schatzel, W. P. Diamond

High methane emissions originating from the active face areas and from the fractured formations overlying and underlying the mined coalbed can adversely affect both safety and productivity in underground coal mines. Since ventilation alone may not be sufficient to control the methane levels in the longwall mining environment, gob gas ventholes have become a standard supplementary methane control option in many mines. As mines progress into deeper and gassier coalbeds, or as longwall panel size increases, ventilation and gob gas ventholes together may not be sufficient to maintain methane levels within statutory limits. To decrease the risk associated with methane emissions under these circumstances, in-seam horizontal methane drainage is often used to reduce the gas content of the coalbed prior to mining. Horizontal methane drainage borehole completion designs, drilling strategies, and degasification lead times may need to be adjusted for site-specific conditions due to mine design, geology, and the gas content of the coalbed. This study investigates different horizontal methane drainage borehole patterns, borehole lengths, and degasification times prior to and during panel extraction to evaluate their effectiveness in reducing methane emissions using a "dynamic" 3D reservoir modeling of a 38 1-m wide longwall panel operating in the Pittsburgh coalbed. Results of this study showed that dual and tri-lateral boreholes are more effective in decreasing emissions and in shielding the entries compared to fewer shorter, cross-panel, horizontal boreholes parallel to the longwall face. Modeling results showed that after 12 months of pre-mining methane drainage, the average longwall face emission rates can be reduced by as much as 10.3 m3/min and 6.8 m3/min using tri- and dual-lateral boreholes, respectively. It was also shown that if pre-mining methane drainage time is short, it is important to continue methane drainage during the panel extraction to maximize reductions in longwall face emissions since additional face emission reductions achieved during this period can be comparable to pre-mining degasification.

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known. There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught firs, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known, There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught fire, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By Khamis Y. Haramy

This Bureau of Mines paper describes the use of the borehole shear tester (BST) In mines. Assembly and procedure sections explain how the equipment is assembled and used properly. Schematics of the BST, limitations, test hole specifications, data recording and calculations are all explained briefly, and an example of the data collecting and calculations is given to assist understanding.

Jan 1, 1981

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

By Arel B. McMahan

The U.S. Bureau of Mines investigated 21 mines, prospects, and mineralized sites in and adjacent to a 38,713-acre portion of the 255,058-acre Kingston Range Wilderness Study Area in 1983. The study area is 35 miles north of Baker, CA in the Mojave Desert. Mineral deposits in and adjacent to the study area are in altered carbonate rocks intruded by diabase sills near monzonite porphyry contacts. Monzonite porphyry forms the core of the Kingston Range and underlies about 70 percent of the study area. Sedimentary carbonate rocks are exposed in bands on the north and east boundaries and as isolated roof pendants in the southeastern portion of the study area.

Jan 1, 1986

By Frank Parrish

History and performance data of 17 water-injection projects in Cooke and Grayson Counties in north Texas are presented for the purpose of studying and comparing operating practices and oil-recovery techniques. Water is injected into Strawn and Canyon sands of Pennsylvanian age. The principal formation flooded is the Strawn, which ranges in depth from 725 to 6,900 ft in the projects covered. Estimated ultimate recoveries range as follows: Primary, 22 to 494 bbl per acre ft; and secondary; 63 to 296 bbl per acre ft. These figures represent the following percentages of original oil in place: Primary, 10 to 46 pct; and secondary, 8 to 23 pct. Shallower projects; 725 to 1,500 ft in depth, had higher average primary and secondary recoveries than did deeper projects. Crude-oil gravity, which ranges from 20° to 45° API, was not relatable to yield of secondary recovery oil. Analysis of the data indicates that five-spot injection patterns will yield the highest percentage of oil remaining at start of flooding; that is, 28.8 pct for five-spot injection patterns, compared with 20.8 pct for line-drive patterns and 11.6 pct for random patterns. Waterflooding in this area appears to be very successful. Secondary recoveries of most projects are expected to nearly equal primary recoveries.

Jan 1, 1963

By Richard F. Hewlett

Engineers at the Bureau of Mines Denver Mining Research Center have been a research program investigating the theory and application of mine sampling. Part of this program is an investigation of the efficiency of sampling methods that involves development of sampling-method theory through simulating ore-deposit samples and assays, using - electronic digital computer. Theoretical developments are checked against actual ore-deposit sampling, assay, and production data by the commonly used polygonal and triangular methods of computing grade and tonnage of ore reserves. To speed the computing procedures, a program has been developed utilizing a medium-size digital computer for computing ore reserves by the polygonal method. This program calculates nine prismoids per minute at a total cost of $0.21 per prismoid. The complete program, written for an augmented IBM 650 computer, is described in detail; it can be used without change for computing ore reserves for a low-grade deposit. Modifications necessary to convert the program to compute ore reserves for virtually any other type of deposit or grouping of ore horizons also are given; however, the program is limited to using only vertical drill-hole data.

Jan 1, 1962

By Alla D. Mah

The need for more and better basic thermodynamic data for the oxides of many of the rare metals is evident to anyone who attempts thermodynamic calculations involving these substances. In continuation of a Bureau of Mines program to meet this need, this paper reports new experimental values of the heats of formation at 298.15° K. of the hexagonal crystalline variety of germanium dioxide and germanium dioxide glass. The values were obtained by means of combustion calorimetry and sodium hydroxide-solution calorimetry. The calorimetric results also made possible the derivation of values for the heat and entropy of fusion of hexagonal germanium dioxide at its melting point. The newly measured data were combined with previously known entropy and high-temperature heat content values to obtain heats and free energies of formation of germanium dioxide (in the hexagonal crystalline, glassy, and liquid states) over the temperature range from 298.15° to 2,000° K.

Jan 1, 1962

By W. K. Overbey

The Bureau of Mines conducted surface joint and stress measurements, airborne remote sensing imagery studies, compass-oriented borehole televiewer surveys, numerical simulation of fractured wells, and well productivity studies in a four-quadrangle study area of Ohio, to determine the effects of earth fracture systems on the deliverability of gas storage fields. The results of these studies indicate that much useful information about a gas storage reservoir can be obtained and put to practical use by studying--(1) oriented cores for fractures and directional permeability, (2) orientation of induced hydraulic fractures for alignment of well patterns, and (3) aerial photos and multispectral scanner imagery for general surface geology comparison and to determine if some, development patterns can be generated by such results. The absence of known tectonic elements associated with flat-lying sediments, such as faults or fracture zones that can be seen on the surface, indicates that the use of remote sensors such as radar or aerial photography is not likely to be useful in picking well locations for drilling. Studies similar to those discussed here should be conducted in gently folded and strongly folded sedimentary formation areas to determine if the increased knowledge of earth fracture systems under these conditions might be beneficial in gasfield and gas storage reservoir development.

Jan 1, 1974

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

By Stanley C. Rhoads

The Bureau of Mines investigated the complete ternary system K2 HfF6¬K2ZrF6-l.25 weight-percent HF at 40° C. In addition, solubility curves have been established at 25°, 30°, 500, 60°, and 70° C. These solubility data implemented a study of hafnium enrichment in feed solutions for liquid-liquid extraction processes.. Selected K2HfF6-K2 ZrF6-1.25 weight-percent HF mixtures were equilibrated in a constant temperature bath. Compositions of the equilibrated solutions and wet residues were established from combined hafnium and zirconium oxide and total fluorine analyses. All solubility curves were essentially parallel on triangular coordinates. At 40° C, the solid phase of the K2HfF6-K2ZrF6-1.25 percent HF system is a series of solid solution hydrates with K2HfF6-H20 and K2ZrF6.3H2O segments existing at the respective extremes. Since this system contains K2HfF6-H20 and K2ZrF6.3H20 segments, it is not ideal for simple separation of high-purity K2HfF6 from K2HfF6-K2ZrF6 mixtures by recrystallization. However, it would be useful for producing hafnium-enriched feed solutions from zircon concentrates for liquid-liquid extraction of hafnium from zirconium.

Jan 1, 1973