Search Documents

By Shiou-Chuan Sun

The froth flotation of coal, differing greatly from that of most minerals1-5, is not improved but rather impaired by temperatures higher than room temperature6-10 This phenomenon has long taunted us for an explanation. Gayle and Associates 8,9 reported the lack of relationship between their contact angle measurements and their flotation of American coals under various temperatures. Bailey and Whelan6 stated that the viscosity of flotation reagents, offering some clue for their flotation of British coals at low temperatures, could not be put forward as an explanation either in whole or in part for the effect of temperatures on coal-flotation. In this paper, a froth hypothesis is proposed to explain the flotation behavior of coals under various pulp temperatures. Test work involved the flotation of coals and the frothing of reagents.

Jan 1, 1966

By D. W. Park

Longwall Strata Control and Maintenance System (LoSCoMS) is a software and data communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels including excessive shield load, low setting pressure, leg leakage and poor shield performance, eminent maintenance problems, etc. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems of their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 1998

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By L. F. Ruppert, R. C. Milici

Coalbed methane (CBM) is currently being produced from a relatively small area in the Dunkard and Pocahontas basins, in the northern and central parts of the Appalachian Basin, respectively. In general, much of the production occurs where the coal beds are beneath 500 feet or more of overburden, where the rank of the coal is high-volatile B or greater (%Ro >0.8), and where the natural fracture system is enhanced by structural deformation. It is anticipated that near-term CBM development will continue within these areas and will expand in the Appalachian basin as technology improves and as the price of gas rises.

Jan 1, 2003

By Sean Cassady, Jason Liu, Sanja Zlatanic, Taehyun Moon, Chris Devery

"For the Hollywood International Airport Runway Expansion Project at Fort Lauderdale, Florida, the structural fire durability analysis was completed for a series of tunnels formed by roadway and railroad cells located under the runway structure. A systematic design approach was developed to mitigate structural damage during a fire event and arrive at a practical method to structural fire engineering that is compliant to NFPA 502. To ensure the NFPA 502 requirements are satisfied, the performance based approach was implemented and the engineering analyses were performed for the adopted design fire event. The analyses considered the facility’s unique features including its fire safety systems to determine applicable design fire curves for structural durability analyses. The paper also outlines the process of defining the project specific fire curves for a specific design fire scenario and summarizes the results of heat transfer and structural fire durability analyses. This approach was aimed to assist the owner and Authority Having Jurisdiction to achieve practical decisions to the tunnel facility fireproofing.INTRODUCTIONFort Lauderdale–Hollywood International Airport (FLL) in Broward County, Florida is a major hub facility serving more than 23 million passengers annually. As part of the Airport Expansion Program, the South Runway (9R-27L) Expansion project aimed to meet ever increasing service demands via an increase to runway lengths. This necessitated the placement of one of the reconstructed runways on bridge structures over the existing U.S. Route 1 (US 1), a major north–south U.S. Highway that serves the East Coast of the United States, and the Florida East Coast (FEC) Railway, thus effectively creating multiple tunnel cells beneath the subject runway. For this project, HNTB suggested a tunnel fire damage mitigation system that would protect the runway major structural elements from the design fire event that may happen within the tunnel cells. This paper addresses the issues related to the fire event originating within the tunnel encompassing the US1 highway only, and deals with requirements of NFPA 502 [5] exclusively. Therefore, while approaching the structural fire protection issues for the specific tunnel cells beneath the runway structure, the requirements of the American National Standard NFPA 502 (Standard for Road Tunnels, Bridges, and Other Limited Access Highways, 2008 edition) were followed. Per this standard, regardless of tunnel length, all primary structural concrete and steel elements shall be protected in order to:"

Jan 1, 2016

By Emily Wortman-Wunder

As the 2010 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2010 issue of Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 328. A significant portion of the contribution that we as a professional society make is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable transfer of technology. Communication within the mining community is the key to a successful society. Through books, magazines, meetings and electronic media, we accomplish the technology exchange that is fundamental to the existence of the Society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, Pennsylvania, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume certainly fulfills that pledge. The 2010 Transactions is the first Transactions to take advantage of new publication technologies. It appears solely as an e-book. The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which will certainly better serve the mining community. I am excited about this development and the opportunities it presents. The 2010 Transactions also contain some of the most exciting research from the past year, including new developments in mineral processing, safety and exploration. Be sure not to miss the two Minerals & Metallurgical Processing issues on the subject of gold hydrometallurgy. This 2010 Transactions comprise of a total of 78 technical papers (582 pages including index), including all 21 papers (136 pages) that were published in 2010 in the Technical Papers Section of Mining Engineering magazine (Vol. 62) and all 34 papers (231 pages) that were published in 2010 in Minerals & Metallurgical Processing (Vol. 27). Addition, this volume contains 23 papers (194 pages) that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 78 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2010 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2010

By A. T. Yu, K. A. Young, Ronald M. Hays, Sanford Terry, D. R. Campbell, J. K. Lovrien, W. L. Price, C. W. Matthews, W. R. van Slyke, S. P. Cole

Storage and transport systems are essential for mineral processing. Section 10 includes systems for storage and transport of dry bulk materials, slurries, and water necessary for operation of mineral pro¬cessing plants. All aspects of these systems are presented, including material characteristics; dry material placement in and reclamation from storage stockpiles and bins; dry material conveyance; hydraulics (liquid flow and pumping); slurry characteristics; slurry storage and reclaim, slurry flow (distributors, launders, and pipes), and pumping; water (primary and secondary process, reclaimed, fire, cooling, and domestic) supply, transport, and storage; equipment selection and sizing; power transmission; controls; and health and safety. The mate¬rials considered include crude ore; process and other water supplies; initial, intermediate; and final in-plant materials; finished materials; and tailings and other waste products. Section 10 is a compilation of practical operating data for engineers, technicians, and plant opera¬tors. For the design of mineral processing plants, including selection and sizing of equipment, the design engineer should consult with equipment manufacturers, suppliers, engineering firms, and plant op¬erators with specialized experience in particular materials handling methods. When unusual conditions are encountered, actual pilot or full scale testing may be required to insure adequate design. Operation of mineral processing plants is dependent on the proper engineering and construction of storage and transport systems for dry bulk materials, slurries, and water. It is obvious that processing plants cannot produce the required quantities of semifinished and finished products unless these material can be transported adequately to, through, within, and from the plant. Costs of storage and transport systems may exceed 50% of the total capital and/or operating costs. Considerable attention must be given to the design, layout, and engineering of these systems. These systems are interrelated with the mineral processing method and it is necessary to determine the best combination of mineral processing method and storage and transport systems. Storage and transport systems perform a major supportive func¬tion to mineral processing. The final selection of these systems depends on the final selection of the processing method and related systems (environmental control, tailings and waste disposal, etc.). The process¬ing method determines the characteristics of materials to be stored and transported; distances, elevations, flow rates for transport; and storage requirements. Flowsheet After selection of the processing method and related systems, a flowsheet must be developed. This flowsheet should indicate produc¬tion rate, percent solids or moisture, and specific gravity for all initial, intermediate, and final products or product flow streams. It also may be necessary to know the size analysis, chemical analysis, abrasiveness, and other physical characteristics of various product flow streams. The flowsheet provides basic information for plant layout, storage requirements, and selection and sizing of process and transport equip¬ment. Storage and transport systems often function improperly be¬ cause of inadequate flowsheet data or process revisions, resulting in improper equipment selection and sizing. Further details on plant design are presented in Section 33. After selection and sizing of process equipment, it is necessary to select the type of material transport equipment to be used for in¬plant materials handling as well as crude ore, tailings, and final prod¬ucts. The storage and/or surge requirements, including capacity and location, then are determined. Storage and/or surge capacity is neces¬sary for leveling production rate fluctuations due to variations in material characteristics; production scheduling; equipment mismatch¬ing, failure, or breakdown; and scheduled maintenance downtime. Variations in ore grindability will cause fluctuations in throughput or production rate for grinding mills and variations in ore grade will cause fluctuations in production rate for concentrating equipment. Variations in material moisture content and percent solids can have serious effects on the capacity of material transport equipment. In some cases, a blending system may be desirable or necessary to reduce variations and to obtain uniform production and/or metallurgy. Storage capacity often is needed because of different production schedules for various phases of the mining and mineral processing complex. As an example, the mine and coarse crushing plant may operate on a one- or two-shift-per-day schedule while the fine crushing plant and concentrator on a three-shift-per-day schedule. This would require storage between the coarse and fine crushing plants. Another example would be load-out storage where unit trains are used to haul concentrate or final products. The concentrator could be operated on a three-shift-per-day schedule while only I to 2 hr may be scheduled for unit train loading. This would require adequate load-out storage so that the concentrator can be operated continuously. Process equipment with mismatched capacities requires storage or surge capacity between the mismatched equipment to achieve oper¬ating efficiency. As an example, the fine crushers may have greater capacity than the rod mills. Storage between the fine crushers and the rod mills permits both the crushers and rod mills to be operated at optimum capacity with the crushers actually operating or running a lesser number of hours per day. Mismatched capacities for process and transport equipment also may require storage or surge capacity. Mismatching of equipment capacities most often occurs because of the difficulty in equipment sizing. Thus, the design engineer must anticipate where in the flowsheet these mismatching capacities are likely to occur while making every effort to assure that equipment is selected and sized properly. Equipment breakdown can cause major operating difficulties and lost production. These breakdowns can be reduced with adequate scheduled maintenance. Lost production due to nonscheduled down¬time caused by equipment breakdown can be reduced further by standby equipment and storage and/or surge capacity ahead of essen¬tial mechanical and electrical equipment. As an example, standby pumps and conveyors often are available as part of the in-plant trans¬port system. Storage and/or surge bins and tanks often serve dual functions, such as dewatering, mixing, and smoothing production rate fluctuations.

Jan 1, 1985

By Lorraine Brandt Yde

This paper describes development of a cost report that is descriptive, logically oriented, and concise. Since the costs involved relate to mining, this reporting technique could help bridge any possible communications gap between "mining men" and computer personnel, at the same time giving the computer-oriented mining individual information to assist him in his job performance. As computers become entrenched in the mining world, meaningful report assimilation becomes a major task. No one should be more capable of defining required results than the man requesting a report. If he is able to clearly state his needs and has researched his problem, it will be reflected in the computer output. During 1970, The Anaconda Company's Berkeley Pit Operation, at Butte, Montana, received many different computer-generated equipment cost reports. Up to thirty-six different components for each type (class) of pit equipment contributed cost data to the Berkeley Pit cost system files for both operating and repairs during current month, year-to-date and accumulation-to-date time periods. This reporting approach was taken to facilitate analyzing this voluminous data. SUMMARY A Major Component Cost Analysis (Exhibits 6-A thru 6-C) developed by arranging the top ten operating and repair percentages (component cost divided by total cost) in descending order, and then accumulating these percentages to a possible one-hundred percent. While tabulating the operating and repair cost percentages by equipment unit number in the current month, year-to-date and accumulation-to-date time periods, a frequency chart is constructed for each equipment

Jan 1, 1971

By Gilles Cachia, Foteini Vasilikou, Seth Pollak, Hannes Lagger

"INTRODUCTION The Shatin to Central Link (SCL) is a new rail line being constructed by the MTR Corporation for the Government of Hong Kong to cater for the growing passenger demand between the North-East New Territories and the urban areas of the city. Contract 1103, which will provide the 4 km of running tunnels between the new Hin Keng and Diamond Hill Stations, was tendered in a design-build framework and awarded to Vinci Construction Grands Projets (VCGP) in October 2012, with Arup as Vinci’s lead designer. One of the most challenging pieces of work on the contract involved the construction of 133m of SEM mined tunnel on the northern end of the project. The Northern Mined Section (NMS) is an undrained, twin-track, single bore profile, broken out through the southern pipe pile wall of the Hin Keng Station cut-and-cover box, Figure 1. The tunnel has maximum excavated dimensions of 14.5m span x 12m height, with track spacing of 6.175m. The general excavation sequence consisted of 3 stages; a 6m high top heading (73.1m2), followed by bench (27.3m2), and invert (26.7m2). A risk-based approach to the design was taken given the large variation in rock level, cover, and an active stream course above tunnel crown. Ultimately, six different temporary support types were utilized in order to optimize the construction process through continually changing ground while maintaining a safe and stable excavation. Three main support types were developed during the initial design phase, along with a “contingency” case, which utilized a partial heading excavation sequence and enhanced face support. The purpose of the contingency support type was to have a robust, engineered design available for immediate implementation should unexpected ground behavior develop, leading to the breaching of instrumentation trigger levels. This support type was never implemented on site. Drill- and-blast tunneling commenced once 6m of rock cover was verified through forward probing. A robust instrumentation and monitoring scheme provided valuable data throughout excavation and the means to carry out a geotechnical back-analysis of the ground behavior and support performance."

Jan 1, 2016

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By Jerry C. Tien

Without a doubt, the scope of China?s coal boom has been nonstop. Despite the world economic slowdown, China?s year-on-year gross domestic product (GDP) jumped 10.3 percent year-on-year in 2010, boosted by a faster than expected 9.8 percent expansion in the fourth [ ] quarter. And, the first quarter of 2011 expanded another 9.7 percent. According to a frequently cited statistic, the country is building two mid-sized coal plants each week. This amounts to a yearly increase equivalent to the entire power grid in the United Kingdom. China?s coal production was doubled in the last 10 years, from 1.044 Gt (1.15 billion st) in 1999 to 3.2 Gt (3.52 billion st) in 2010. This is 3.2 times the U.S. production (986 Mt or 1.085 billion st) and nearly half (46.3 percent) of the world?s total coal production (6.91 Gt or 7.6 billion st). This rapid increase of demand for coal has made China the world?s largest coal importer in 2009. With the economic situation improving, this trend is expected to continue.

Jan 1, 2011

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By Ronald J. Riberich

The Mineral Economics and Management Society (MEMS) held its fifth annual conference in Montreal, Quebec, Canada earlier this year. “The Minerals Industry: Responding to the Global Challenge” was the first MEMS conference to be held outside of the United States. About 125 mining- and minerals-related professionals attended. The MEMS program included six sessions and three distinguished speaker addresses. The session topics included: “Minerals in the Macro economy: Development in Demand,” “Trends in Global Metals Supply: The Producers’ Challenge,” “Global Environmental Issues: Policy Perspectives,” “Global Environmental Issues: Quantitative Analysis” and “Minerals in the CIS: Phoenix or Albatross?” A student session was also offered. It provided a competition for monetary awards for outstanding papers.

Jan 1, 1996

By Steve Klein

Weak rock is an important consideration in tunnel design and construction due to the difficult ground conditions that are often encountered. Nevertheless, when conditions are favorable high advance rates can be achieved leading to economical tunnel construction. Successful construction of a tunnel in weak rocks depends on correctly anticipating the behavior of these unique materials. The objective of this paper is to provide guidelines that can be used to accurately classify the performance of weak rock in tunnels.

Jan 1, 2001

A machine that improves safety during the cutting of boxholes (ore-passes) and travelways in underground mining operations has delivered impressive results in trials conducted at a South African platinum mine. The technology is a joint effort by Sandvik Mining and Construction and platinum mining company Lonmin. The ABH 1600 boxhole borer was built by Voest-Alpine Bergtechnik, Sandvik’s Austrian subsidiary. It was delivered to the Lonmin Eastern platinum mine in February 2005. There, it was deployed underground on the Number 8 Level (320 m or 1,050 ft below the surface) at the mine’s Newman incline shaft.

Jan 1, 2006

By E. Cho

Illinois No. 6 coals of IBC 101 and IBC 112 were treated in solution with sodium hypochlorite to remove their sulfur contents, especially organic sulfur. The lab experiments were conducted in two steps of leaching at room temperature and hydrolysis at 90oC. The removal of organic sulfur from IBC 101 was by 37.8% while that from IBC 112 was only 13.7% under their respective optimum conditions. This large difference in organic sulfur removal is considered to be due to difference in concentration of surface total acid group, 3.14 vs. 0.88 mmol/g of coal.

Jan 1, 2007

By E. Bakhtavar

All parameters influencing the decision for selection of a suitable extraction method were first selected as the base of this study. Then these parameters were categorized in two main groups. The first group of the parameters includes ?geomechanical and inherent characteristics of the dimension stones? such as hardness, RQD, compressive strength, joints plane orientation and spacing, and water content. The second group was named ?technical and economical parameters associated with the investor?s objectives? like for example extraction capacity (production rate), blocks recovery, mechanization, capital investment and operational costs. Finally, the influences of all mentioned parameters on the selection of the most applicable extraction methods have been assessed and discussed.

Jan 1, 2012

By R. L. Guerguerian

Critical fasteners are described as they apply to the specification, manufacture, and assembly on large grinding mill bolted joints. The importance of adequate design methods, related joint diagrams and pivot analyses, and special emphasis on the quality of manufacturing and the tightening procedures in the field, are discussed; all in an effort to ensure high availability plant operation.

Jan 1, 2001