Search Documents

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By L. J. Prosser, A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia [(Figure 1)]. Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden (> 30 m [l00 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Feb 24, 1997

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Dave Ragland

The SDSU tunnel and underground station are the first of these type facilities to be constructed by the Metropolitan Transit Development Board. Because there is no previous experience, and because tunneling activities are associated with some risk, he MTDB has undertaken a very proactive and wide reaching program to identify and control risks during construction. Finally, because the tunneling activity and underground station is on the San Diego State University, MTDB is working closely with their staff to identify construction impacts and mitigation’s, and thus ensure a quality project for both agencies.

Jan 1, 2001

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

By Yoshihiro Kawarabata

INTRODUCTION With only about 30% of Japan's entire population served by sewer systems at the end of 1980, extensive sewerage construction programs have been implemented. As major sewer networks in large cities are near completion, construction of smaller sewer networks in less populated areas and branch sewers in urban areas is on the rise, where a demand for sewer tunnels of 600mm to 1500mm diameter is very heavy. The pipe jacking technique, usually employed to excavate such small diameter tunnels, therefore has become the subject of further technological development and sophistication to cope with the increasing volume of construction. At the 1979 RETC, the state of the art on the slurry shield tunneling method at that time was reported. This paper is a follow up to the last paper and discusses a newly developed boulder crushing equipment and automatic pipe jacking system for the slurry shield method and their application. Such technological advancement as high-degree mechanization and automation will significantly improve tunneling operations in response to the aging society to come. Through application of the technique on so called factory automation, this is a step towards field automation for the construction industry.

Jan 1, 1983

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By J. P. Kennedy, O. A. Bascur

Large metallurgical complexes have more data than a small city and these data change as internal and external conditions evolve. Staffing turnover hinders experienced-based decisions especially with simple tools like spreadsheets. Lack of current information can contribute to decisions that result in significant deterioration in the quality of operation. Timely, unified information from sophisticated analyses presented to the broadest possible reach will improve operation. The major innovation is the addition of the web browser to the suite of software people will use with no training – the other two are spreadsheets and graphical presentations – and the consistent organization and transformation of the real time data to support broad access. This paper describes the data transformations and presentation methods necessary for a Web view, especially the special needs of real time data and analysis required for active operations decision-making. Many people inside and outside the complex, not just operators, need timely information that is abstracted, aggregated, organized and unified. Unification and aggregation of real time data presented via the Web opens a new paradigm for collaboration. The analysis tools are as important as the data. These rule-based tools add significantly to the operations database in the form of results stored for viewing with plant data. Mining and metallurgical plants already use many sophisticated analysis tools such as predictive maintenance policies based on statistical analysis vibration analysis, and oil and lube analysis for critical equipment. These add real time events, similar to an alarm package, and unified production information to the operational database. Simple models are used on line to create key indices that provide a real time indication of performance. Key indices include metrics for losses due to plant availability, performance efficiency, and overall process equipment effectiveness. These additional data in the operations database are used for early fault detection, increased production, better quality, higher availability of equipment and faster detection of process bottlenecks. An important feature is the ability for people to create their own key indices and store the results for use by anyone in the plant historian, but accessible by a browser. Keywords: plant information, principle components analysis, data reconciliation, gross error estimation, Internet, Word Wide Web

Jan 1, 2002

By Y. Nien Wang, Moe Amini, Heiner Sander, Max John

INTRODUCTION As the population increased along the coast route (California Route 1), and the people’s need to have guaranteed access increased, the landslides and related road closures began to have serious adverse economic impacts. Landslides were causing major long-term road closures about every 10 years on average. In 1983, ground movement at Devil’s Slide caused Highway 1 to be closed for an extended period of time which caused significant economic loss to the surrounding coastal communities. A number of options for bypassing the slide area were considered, and the Martini Creek inland bypass was selected for design. Subsequent litigation led to the creation of the Devil’s Slide Tunnel Study in 1996. The results of this study indicated that a tunnel alternative would be competitive with the inland bypass. The final decision was left to the citizens of San Mateo County, who approved the tunnel alternative in the November, 1996 election After completion of environmental studies and the processing of legal challenges, the final environmental document was finished in 2001. The preferred tunnel alternative was designated to proceed for final design and construction. PROJECT DESCRIPTION The Devil’s Slide Tunnels consists of a separated two-lane road, one lane in each direction, which passes through twin tunnels and over twin bridges and then connects with the existing non-separated, two-lane road at each end. The total length of the project is approximately 1900 meters consisting of four main project divisions, which are described below, going from south to north. 1.Operations and Maintenance Center (OMC) area, 2.Southern approach roadways to the South Portals (250 meters), including the South Rock Cut,

Jan 1, 2005

By Yoginder P.

ACKNOWLEDGEMENTS Authors sincerely appreciate the interest, cooperation and technical support of the coal company management and staff in conducting the study. Without their assistance this study would not have been possible. INTRODUCTION AND SPECIFIC OBJECTIVES An area in the midwest overlying abandoned room-and-pillar mine workings at, shallow depth has been experiencing subsidence movements with associated damage to surface structures. Other coal companies in the area have also been having similar experience. A 16 - month cooperative study between a mining company and the Department of Mining Engineering at SIUC was developed with the following objectives. 1) Determine the extent to which surface and subsurface movements were complete in the area, 2) Identify the mechanism(s) of subsidence in the area, 3) Determine the influence of geology and hydrology of the area on subsidence movements, 4) Observe the conditions of abandoned underground workings with a borehole TV camera, 5) Characterize the extent of damage and monitor possible progressive damage to selected surface structures, and 6) Make recommendations to a) minimize further damage to surface structures in the area, b) identify future areas that may be affected by these movements and c) modify mining systems to minimize these movements.

Jan 1, 1986

By K. Short

Over the past several years, the mining and minerals market was overloaded with discussions around reviving mature terminologies like distributed control systems (DCS), programmable logic controllers (PLC), and the ?new comers?: hybrid control systems (HCS) and programmable automation controllers (PAC) and, in parallel, which technologies would be more appropriate for mining and mineral processing applications. Ten years ago, a careful comparative analysis would make more sense. Control approaches had very distinctive differences where users needed to choose the right approach.

Jan 1, 2012

By Tom Dettweiler, Robina Sharpe, Wright. Michael

The International Seabed Authority and a number of countries have or are in the process of developing environmental impact assessment guidelines and legislation for seafloor mineral development. The formal decision to grant a project an environmental permit is based on an environmental and social impact assessment (ESIA), culminating in an environmental impact statement (EIS). The EIS needs to be supported by sufficient data upon which an assessment of impacts can be made and mitigation measures developed. Given the remote locations of many seafloor prospects, collection of sufficient environmental data to inform an EIS is often a difficult, expensive and lengthy process.

Sep 1, 2014

By A. Habibi

A study has been undertaken on two 1.12 m diameter industrial booster fans operating under different blade settings powered by a 1200 rpm motor at the Missouri University of Science and Technology. The fans total pressure varies up to 1kPa forcingup to 25 m3/s through the workings. A pressure-quantity survey has been conducted inby and outby the booster fans with different blade settings. The study uses a variable speed drive (VFD) to determine the effect of rotational frequency on the system. The pressure drop across the bulkheads has been monitored during the experiments. The fans were operated with various blade settings to determine the optimal scenario that maintains the maximum airflow quantity and the lowest power demand at a particular ventilation station. Five scenarios were conducted with different blade setting and mostly with two different speeds. The experimental results show that alteration of fans? speeds by use of a VFD unit can reduce power consumption while maintaining airflow requirements. With the flow rate forced through the mine by the surface fan the blade settings 4 and 5 were determined as possible alternative for the mine ventilation system. In scenario 4, the airflow at the particular ventilation station for a number of speeds is over 20m3/s. The power consumption at 1080 rpm was measured to be 20.1 kW compared to 25.5 kW at 1200 rpm. The operating cost would be significantly less at lower speeds. Scenario 5 is the alternative making use of both booster fans and the main fan in series that meets the minimum airflow requirement at the particular ventilation station along with minimum power consumption. Reducing both booster fans speeds to 1054 rpm results in power consumption of both together dropping to 11.8 kW. Therefore blade setting 5 using two booster fans was determined to be the optimal setting. Separately it was determined that the combination with use of only one booster fan, the West booster fan, running in series with the main fan is the overall optimal scenario. The power consumption of the West booster fan was calculated to be 8.8 kW at 860 rpm with the minimum airflow requirement being met. Computational fluid dynamics is used for analyzing three dimensional flow structures in time domain and calculating the corresponding unsteady pressure fluctuations. The sliding and dynamic mesh techniques were used to study the unsteady flow interaction arising due to the rotation of the fan blades. The numerical predictions of the variables in the form of velocity vectors and contour plots detailing the flow characteristics are then analyzed according to the known physical situation and existing experimental data.

Feb 27, 2013

By D. M. Wagner, G. Biggs, M. Osmundson, C. J. Twaroski

Potential air emission impacts to federal Class I areas from distant sources are receiving increasing scrutiny by federal land managers (FLMs). This paper provides summary results of the impact analyses conducted for FLMs and PSD permitting of a proposed expansion for a taconite processing facility. Results from air quality increment, acid deposition, mercury deposition, and visibility analyses for Class I areas located 50 to 162 km from the facility showed the project would meet the respective regulatory and guideline values for the specific analyses. During the course of the air quality analyses, potential new requirements from the FLMs’ Air Quality Related Values Workgroup (FLAG) efforts and USEPA’s Regional Haze Program were brought into the PSD discussions. The implications for these future guidelines and regulations as they may affect future expansions at other mineral processing facilities are also discussed.

Jan 1, 2001

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

By M. Weatherspoon, S. Gebo, K. Prisbrey

Our objective was to develop a transfer function model of phosphate heap leaching for design, optimization and control. The procedure included analysis of time-lapse photography of a laboratory heap. Our experimental results confirm the predicted system transfer function kinetics. Our conclusion was that the transfer function and z transform that we have developed will allow us to control flow rate and pH online.

Jan 1, 2001