Search Documents

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

By S. Kouniali

Experience with knowledge-based systems for Layout planning and roadway support dimensioning is on hand in European coal mining since 1985. The systems SOUT (support choice and dimensioning, 1989), SOUT 2, PLANANK (planning of bolt-support), EXOS (layout planning diagnosis. 1994), Sout 3 (1995) have been developed in close cooperation by CdF1. INERIS2. EMN3 (France) and RAG 4, DMT5, TH - Aachen6 (Germany); ISLSP (Integrated Software for Layout and support planning) development is in progress (completion scheduled for July 1996). This new software technology in combination with conventional programming systems. numerical models and existing databases turned out to be suited for setting-up an intelligent decision aid for layout and roadway support planning. The system enhances reliability of planning and optimises the safety-to-cost ratio for ? deformation forecast for roadways in seam and surrounding rocks, consideration of the general position of the roadway in the rock mass (zones of increased pressure, position of operating and mined panels). ? support dimensioning ? yielding arches, rigid arches, porch sets, rigid rings, yielding rings and bolting / shotcreting for drifts ? yielding arches, rigid arches and porch sets for roadways in seam ? bolt support for gateroads (assessment of exclusion criteria and calculation of the bolting pattern) ? bolting of face-end zones (feasibility and safety assessment, stability guarantee).

Jan 1, 1996

By Charles Steed

The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.

Jan 1, 2003

By Keith A. Heasley

Numerous different instruments and techniques have been developed for the purpose of measuring rock stress and stress changes around excavations. The interpretation of the output from many of these instruments has often been problematic. This paper covers the research performed in attempting to analyze one particular stress measuring instrument called the Borehole Platened Flatjack (BPF) . The approach used in this analysis was to combine the analytical solution for the displacements around a borehole and the analytical solution for the bore- hole-platen interaction with the empirical stiffness behavior of the flatjack. The resulting model of the BPF response was then verified using measured laboratory data with very good results. In addition, techniques for applying the method to the field are briefly discussed. The major accomplishments of this comprehensive modeling and testing program are; 1) the establishment of the critical installation and site parameters of the hydraulic pressure cell and 2) the development of a systematic procedure for calibrating the cell based on the given values of these critical parameters.

Jan 1, 1989

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By John C. Stankus

To improve mine roof bolt performance, Jennmar Corporation commenced the design and development of a new roof control sys- tem. This new system designated "Insta'l Compression", not only improves safety, but is more cost efficient due to reduced amounts of resin needed per bolt installation. In this paper the research and development of this new system will be outlined. Much of the information presented will be actual test data from various underground operations in Alabama, Kentucky, and Pennsylvania. The development of this system will also cover the design of a new expansion shell, resin compression ring, anti- friction washer, and upgrading of material specifications.

Jan 1, 1990

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By F. Ziaie

Line electrical resistivity method using physically infinite distance between current line electrodes is proposed to determine the location of mine workings. In this method at least three line electrodes are used. One of the current electrodes is used as a sinkhole electrode while the other two are used for different activiations of line electrodes when the survey area is between one of the line electrodes and outside the other one. The resistivity profiles perpendicular to the current line electrodes for different activation of electrodes is plotted versus the distance of the midpoint of the measuring potential electrodes. The anomaly due to presence of any locally lateral resistivity variation (e.g. mining cavity) will represent itself as peak or trough depending on resistivity contrast between the source of the anomaly and surrounding medium. Physical simulation of the proposed model was conducted by using a tank model in the laboratory. The results of experiments appear to be consistent with the theoretical model. Experiments for different depths and different spacial locations of the simulated cavities appeared to be successful for locating the depth and size of the cavity.

Jan 1, 1989

By Archie Richardson

The trona mines in the Green River Basin, commonly known as the "trona patch," present an interesting set of rock mechanics issues stemming from mining in a unique underground environment. Like other minerals occurring in tabular deposits, trona is mined using high-productivity room-and-pillar and longwall methods. However, trona does not behave quite like other evaporites and behaves far differently than coal. In this paper, the following key issues in trona patch rock mechanics are discussed: material properties, in situ stress field, water and gas pressure effects, creep characteristics, pillar behavior, roof span stability, floor stability, underground tailings storage, longwall mining, two-seam mining. and solution mining. Many of the existing trona producers are entering potentially more difficult mining conditions, and much consideration is being given to "new" technologies such as longwall mining and solution mining. In analyzing 20 years of experience with trona patch rock mechanics issues the authors have identified key comparisons and contrasts with conventional tabular deposit rock mechanics that will help illuminate what has been learned as the trona patch enters the 21" century.

Jan 1, 1999

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By D. S. Choi

This paper describes an improved source location technique for microseismic events related to coal mining. A system of non- linear distance equations is solved with the use of the Newton-Raphson method. This computational method is- advantageous when the number of geophones is limited. In addition, this paper includes the results of the analysis of data from several instruments which characterize both mine seismicity and environmental noise such as vehicle traffic. Analysis of the mine seismicity has contributed to a better understanding of caving above a longwall gob and of what constitutes stable ground conditions.

Jan 1, 1990

By Shosei Serata

The application of conventional rock mechanics methods to complex ground is very difficult. Yet. In most underground mining, the ground is complex. Therefore. conventional methods are not only difficult to apply but are also generally ineffective in improving underground operations. Similarly, conventional rock mechanics instrumentation has not significantly contributed to improvement of mining practice. Rock mechanics instrumentation in underground mining operations is often considered to be" merely an expensive nuisance. A new system of mine instrumentation is changing this traditional view. The new instrumentation method, called the SPDR method, was originally devised by Dr. Shosei Serata to meet the specific requirement of establishing the Stress Control Method of mining upon a solid quantitative foundation. This instrumentation method has contributed substantially to the widespread success of Stress Control mining under widely varying ground conditions in different types of underground mines (1.2.3.4). The instrumentation method provides an effective means for optimizing Stress Control mining patterns, simultaneously achieving reduction in production costs and substantial improvements in safety (5). The principles and methods of the new instrumentation method are described below, with field examples.

Jan 1, 1986

As the surface reserves are being depleted, more and more stone operators are seeking underground mining options. Stability of underground openings is a major concern for the safety and productivity. This paper relates to a field study conducted at a large underground limestone mine in Central Pennsylvania. Identification of hazards leading to ground failures and assessment of roof fall risks are important in mitigating injuries. Field observations at this mine were integrated with Roof Fall Risk Index (RFRI) mapping software recently developed by West Virginia University. The system is designed to combine field study data related to geologic factors, mining-induced damages, roof profile, and ground water influx to generate RFRI maps. The mine has adopted a proactive ground control program consisting of comprehensive examination of drilling and bolting logs; precision surveying of roof and rib; accurate mapping of cutters, falls, and geologic structures; and installation of extensometers and microseismic monitoring systems. Investment of time and resources has eliminated fatalities and lost-time injuries due to ground fall. This paper presents the geologic settings, mining conditions, ground control issues along with risk management and control techniques adopted at the study mine.

Jan 1, 2009

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012